Sol_140L3725Q0021.pdf

Quoters Copy Issuing Office:

BLM NIFC

Quotes Are Solicited For:

Pass Creek Hand Thinning

Solicitation: 140L3725Q0021

This solicitation can be downloaded at https://www.sam.gov.

IMPORTANT – NOTICE TO ALL PROSPECTIVE QUOTERS

Quotes shall be emailed to the Contracting Specialist, at Daniel Rosales drosales@blm.gov by 1000 hours, Mountain Daylight Time, 03/12/2025.

As part of its quote, the quoter shall complete/submit the following:

(a) SF 1449, Blocks 17a, 30a-30c;

(b) Fill in the appropriate information requested in Section B.1, Schedule of Items;

(c) Provide your responses to Sections E.3 Instructions to Offerors; and,

(d) Contact information for an individual with the authority to bind.

(e) Questions can be submitted via email until 3/07/2025 @ 1000 Mountain Daylight Time. Answers to questions will be submitted to SAM.gov as an amendment.

(f) No site visit is scheduled, but interested vendors may visit site at their convenience. Additionally, interested vendors may reach out to the COR Jeremiah Moore JLMoore@blm.gov if you would like to formally visit the site with the Government representative.

Quotes that arrive after the prescribed time for receipt of quotes will be considered late and treated in accordance with FAR 52.212-1, Instructions to Offerors-Commercial Items.

It is the Quoter’s responsibility to monitor the following website for any changes to the RFQ: https://www.sam.gov.

Quotes submitted in response to the solicitation shall honor the offer for 60 days.

This solicitation neither commits the Government to pay any cost incurred in the submission of the quote or in making necessary studies or designs for preparing the offer, nor to contract for services or supplies. Any cost incurred in anticipation of a contract shall be at the Quoter’s own risk.

Quoters may contact the Contracting Specialist, Daniel Rosales at drosales@blm.gov.

http://www.sam.gov/ mailto:JLMoore@blm.gov http://www.sam.gov./ mailto:drosales@blm.gov.

SEE ADDENDUMIS CHECKED

CODE 18a. PAYMENT WILL BE MADE BY

CODE

FACILITYCODE

17b. CHECK IF REMITTANCE IS DIFFERENT AND PUT SUCH ADDRESS IN OFFER

OFFEROR

LFA

BOISE ID 83705

3833 S. DEVELOPMENT AVE.

BLM FA NTL INTRAGCY FIRE (FA250)

0011276309 CODE 16. ADMINISTERED BYCODE

X

X

X

115310

SIZE STANDARD:

100.00 % FOR:SET ASIDE:UNRESTRICTED ORLFA

REQUEST FOR

PROPOSAL

(RFP)

INVITATION

FOR BID (IFB)

10. THIS ACQUISITION ISCODE

REQUEST FOR

QUOTE (RFQ)

14. METHOD OF SOLICITATION

13b. RATING

NORTH AMERICAN INDUSTRY

CLASSIFICATION STANDARD

(NAICS):

SMALL BUSINESS

03/12/2025 1000 MD

02/25/2025

Daniel Rosales (No collect calls)

INFORMATION CALL:

FOR SOLICITATION 8. OFFER DUE DATE/LOCAL TIMEb. TELEPHONE NUMBER a. NAME

4. ORDER NUMBER3. AWARD/ 6. SOLICITATION

140L3725Q0021

5. SOLICITATION NUMBER

SOLICITATION/CONTRACT/ORDER FOR COMMERCIAL ITEMS 1. REQUISITION NUMBER PAGE OF

1 52 0044006467OFFEROR TO COMPLETE BLOCKS 12, 17, 23, 24, & 30

TELEPHONE NO.

17a. CONTRACTOR/

CANON CITY CO 81212

3028 E MAIN STREET

BLM-CO ROYAL GORGE FIELD OFFICE*

15. DELIVER TO

BOISE ID 83705

3833 S. DEVELOPMENT AVE.

9. ISSUED BY

7.

2. CONTRACT NO.

EFFECTIVE DATE

$34

18b. SUBMIT INVOICES TO ADDRESS SHOWN IN BLOCK 18a UNLESS BLOCK BELOW

ISSUE DATE

DELIVERY FOR FREE ON BOARD

(FOB) DESTINATION UNLESS

BLOCK IS MARKED

11.

SEE SCHEDULEX

12. DISCOUNT TERMS THIS CONTRACT IS A RATED

ORDER UNDER THE DEFENSE

PRIORITIES AND ALLOCATIONS

SYSTEM - DPAS (15 CFR 700)

13a.

SERVICE-DISABLED

VETERAN-OWNED

SMALL BUSINESS

(SDVOSB)

HUBZONE SMALL

BUSINESS

8(A)

BLM FA-NTL INTRAGCY FIRE CTR(FA250)

WOMEN-OWNED SMALL

BUSINESS (WOSB)

ECONOMICALLY DISADVANTAGED

WOMEN-OWNED SMALL

BUSINESS (EDWOSB)

24.

AMOUNT

23.

UNIT PRICE

22.

UNIT

21.

QUANTITY

20.

SCHEDULE OF SUPPLIES/SERVICES

19.

ITEM NO.

Delivery: 12/15/2025

00010 Pass Creek Handthinning Product/Service Code: F014 Product/Service Description: NATURAL

RESOURCES/CONSERVATION- TREE THINNING

Period of Performance: 03/21/2025 to 12/15/2025

Continued ...

(Use Reverse and/or Attach Additional Sheets as Necessary)

HEREIN, IS ACCEPTED AS TO ITEMS:

X

XX

DATED

Daniel Rosales

. YOUR OFFER ON SOLICITATION (BLOCK 5),

INCLUDING ANY ADDITIONS OR CHANGES WHICH ARE SET FORTH

COPIES TO ISSUING OFFICE. CONTRACTOR AGREES TO FURNISH AND DELIVER

ARE

ARE

31c. DATE SIGNED

27b. CONTRACT/PURCHASE ORDER INCORPORATES BY REFERENCE FAR 52.212-4. FAR 52.212-5 IS ATTACHED. ADDENDA

31a. UNITED STATES OF AMERICA (SIGNATURE OF CONTRACTING OFFICER)

30c. DATE SIGNED 31b. NAME OF CONTRACTING OFFICER (Type or print)

ALL ITEMS SET FORTH OR OTHERWISE IDENTIFIED ABOVE AND ON ANY ADDITIONAL

SHEETS SUBJECT TO THE TERMS AND CONDITIONS SPECIFIED.

27a. SOLICITATION INCORPORATES BY REFERENCE (FEDERAL ACQUISITION REGULATION) FAR 52.212-1, 52.212-4. FAR 52.212-3

AND 52.212-5 ARE ATTACHED. ADDENDA

26. TOTAL AWARD AMOUNT (For Government Use Only)

OFFER

STANDARD FORM 1449 (REV. 11/2021)

Prescribed by GSA - FAR (48 CFR) 53.212

ARE NOT ATTACHED.

ARE NOT ATTACHED.

AUTHORIZED FOR LOCAL REPRODUCTION

PREVIOUS EDITION IS NOT USABLE

30b. NAME AND TITLE OF SIGNER (Type or print)

30a. SIGNATURE OF OFFEROR/CONTRACTOR

28. CONTRACTOR IS REQUIRED TO SIGN THIS DOCUMENT AND RETURN

25. ACCOUNTING AND APPROPRIATION DATA

29. AWARD OF CONTRACT: REFERENCE

32e. MAILING ADDRESS OF AUTHORIZED GOVERNMENT REPRESENTATIVE

32c. DATE 32b. SIGNATURE OF AUTHORIZED GOVERNMENT REPRESENTATIVE

ACCEPTED, AND CONFORMS TO THE CONTRACT, EXCEPT AS NOTED:

32a. QUANTITY IN COLUMN 21 HAS BEEN

RECEIVED INSPECTED

40. PAID BY39. S/R VOUCHER NUMBER38. S/R ACCOUNT NUMBER

37. CHECK NUMBER

FINALPARTIAL

36. PAYMENT

FINALPARTIAL

35. AMOUNT VERIFIED

CORRECT FOR

34. VOUCHER NUMBER33. SHIP NUMBER

COMPLETE

32g. E-MAIL OF AUTHORIZED GOVERNMENT REPRESENTATIVE

42d. TOTAL CONTAINERS42c. DATE REC'D (YY/MM/DD)

42b. RECEIVED AT (Location)

42a. RECEIVED BY (Print)

41c. DATE41b. SIGNATURE AND TITLE OF CERTIFYING OFFICER

41a. I CERTIFY THIS ACCOUNT IS CORRECT AND PROPER FOR PAYMENT

STANDARD FORM 1449 (REV. 11/2021) BACK

24.

AMOUNT

23.

UNIT PRICE

22.

UNIT

21.

QUANTITY

20.

SCHEDULE OF SUPPLIES/SERVICES

19.

ITEM NO.

32f. TELEPHONE NUMBER OF AUTHORIZED GOVERNMENT REPRESENTATIVE

32d. PRINTED NAME AND TITLE OF AUTHORIZED GOVERNMENT REPRESENTATIVE

52 2 of

SECTION B – SCHEDULE OF ITEMS/DESCRIPTION/SPECIFICATIONS

B.1 SCHEDULE OF ITEMS/PRICE SCHEDULE

Item Supplies/Services Qty Unit of

Issue

Unit Price

Total Price

0010 Pass Creek Hand Thinning 80 ACRE $ $

Total

FFP

C.1 – GENERAL REQUIREMENTS

C.1.1 – PROJECT OBJECTIVES

The treatment project is designed to cut and pile all conifer tree species in a riparian zone near Poncha Springs, CO.

The main objectives of this project are to improve and enhance wildlife habitat and forage, and to increase the vigor of the riparian tree species. This treatment will be accomplished with chainsaws and hand crews. The total project size is 80 acres in 1 treatment unit. Terrain and topography is variable, and it is recommended that the contractor attend the pre-bid inspection tour, as given below, to determine actual amount and type of work needed to complete this contract.

The stipulations listed in “Description of the Work” will be required within the acres of the project area (J.2: Pass Creek Project Map).

C.1.2 - LOCATION OF PROJECT

The project area is located near the community of Poncha Springs, CO, accessed via Fremont County Road 212. The legal description is: Chaffee County, Sixth Principal Meridian, T. 49 N., R 7 E., sections 13 and 14 (See J.1: Pass Creek Vicinity Map).

C.1.3 – SCOPE OF CONTRACT

The Contractor shall develop and submit a Treatment Plan and Schedule to accomplish the project objectives, and organize and direct all of the equipment and personnel needed to fully accomplish the work. The contractor shall furnish all technical expertise, labor, equipment, supervision, transportation, operating supplies, and incidentals necessary to complete the work required. The Treatment Plan and Schedule will be agreed upon by both parties and incorporated into the contract. All changes to the Treatment Plan will be agreed to prior to the changes taking effect.

The contractor shall be required to:

1. Provide a Treatment Plan and Schedule. See section C.1.3.1

2. Provide a Quality Control Plan. See section C.3.

3. Provide a Safety Plan. See section C.2.13.1

C.1.3.1 The Treatment Plan and Schedule shall include as a minimum the following items: Schedule for completion of objectives, personnel and equipment involved.

C.1.4 - DESCRIPTION OF WORK

Reserve Trees:

1) All Aspen, Rocky Mountain Maple, Alder, Birch, and oak

2) All ponderosa pine, Douglas-fir, and spruce greater than 7” DBH

Solicitation No. 140L3725Q0021

Pass Creek 2025

Project Specifications:

1) Cut all conifer trees

2) Stump heights cannot exceed 6 inches in height and all live branches will be severed from the stump.

3) No trees shall be felled toward or across any improvement such as, but not limited to roads, trails, fences, gates, signs and spring developments. Section corner monuments, survey markers, and private land boundaries will be protected. The contractor is responsible for the removal of all created slash and debris from roadways and trail.

4) All cut trees will be piled according to pile specifications below.

5) No off-road vehicle use.

Piling Specifications

1) All cut material will be hand piled.

2) Slash that would cause large air spaces in piles shall be sectioned (e.g. cut into smaller pieces).

3) Each slash pile shall have a minimum volume of 10-15% by volume of small sized slash (small branches less than ½ inch in diameter and or small branches with needles attached) placed in the lower, center of the pile, to provide kindling for prompt ignition to aid in the combustion of the larger slash.

4) Place larger diameter of the limbs (butt end) toward the center of the pile (up and into the pile) so that heavier material is in the center of the pile for more complete combustion.

5) Piles must be 10 feet wide by 10 feet tall or larger.

6) Piles will not be within 50 feet of another pile, to achieve this; slash will need to be dragged to be consolidated into bigger piles.

7) All limbed material shall be hand piled.

8) No piles will be within 30 feet of private land boundaries, land survey monuments, overhead power line/phone lines, or other improvements.

9) Slash pieces projecting 1 feet or more beyond the general perimeter of the pile shall be cut off and piled.

10) Piles will not be placed in avoidance areas that have been identified by the COR.

11) Piling methodology, pile location and orientation shall not result in unstable piles. All piles shall be as compact as possible and constructed so they will not topple

12) Piles should be at least 10 feet away from standing trees and located so that the burning will not cause damage to standing trees.

13) No soil, other than that adhering to the bark or contained in the root ends, will be acceptable in piles.

14) Clear all dead material within 15 feet of piles and incorporate into pile.

C.1.5 - CONTRACT PERIOD

This project will begin as soon as possible (no cutting between May 15 and July 15), but no later than 30 days after the award date. Holidays do not count as weekdays. Work will be completed by December 15, 2025. Consideration will be given to delays caused by bad weather or wet road conditions.

C.1.6 DEFINITIONS

DEFINITIONS

Bearing Tree - A tree which is used as a reference monument to locate a property corner.

Biomass- Biomass – Any tree, or portion of, less than 6 inches DBH and top, limbs, or slash of a merchantable tree.

Bole – The central stem of a tree, with no limbs, once it has grown to substantial thickness

Brush - Vegetation consisting of shrub species with single or multi-stems originating at or near ground level not normally reaching twenty feet in height. Examples include but are not limited to oakbrush, serviceberry, and sagebrush.

Conifer – A tree that is a gymnosperm, usually an evergreen with cones and needle-shaped or scale like leaves, i.e.

Douglas-fir, ponderosa pine, white fir, Rocky Mountain juniper or piñon pine.

CO – Contracting Officer

COR – Contracting Officers’ Representative

COR/PI - either the COR or the PI

Cut Leave Tree - A tree noted during inspection as a tree that should not have been cut.

DBH – Diameter at Breast height. The diameter of a tree measured at 4.5 feet from the ground on the uphill side.

DRC-Diameter at Root Collar or at the ground level.

Damaged Leave Tree - A tree damaged through the cutting and/or felling of other trees.

Forest Products – “Other vegetative resources” and “Timber” as defined in 43CFR5400.0.0

Fuelwood – Smaller diameter forest products that are generally used for heating.

Landing – A flat location cleared of trees within or near the treatment area with room to deck forest products for subsequent transportation.

Lodged Trees and Brush - Cut trees and brush leaning into, supported by, or covering a leave tree.

Muddy – Soil moisture conditions high enough for equipment to leave ruts over 1.5 inches in depth from the natural ground level.

PI – Project Inspector

Reserve Trees - Trees not to be cut.

Severe – To completely separate from the whole.

Slash - Any material which has been cut by the Contractor during mulching operations

Unsevered – not completely separated from the whole, pieces still attached.

**When a disagreement over definitions not listed arises, the Society of American Foresters, THE DICTIONARY of FORESTRY, will be used to determine accepted definitions.

SECTION C.2 – TECHNICAL REQUIREMENTS

C.2.1 - BLM WILL FURNISH OR PROVIDE THE FOLLOWING

1. Designate the boundary of the areas to be treated with orange plastic surveyors flagging.

2. Provide maps and descriptions of the area, and go with the operator around the boundary of the area.

3. Project area is publicly accessible, but if vendors would like to schedule a pre-bid tour, contact the COR.

4. Conduct on-site inspections by the PI/COR.

5. The CO/COR are available to approve/disapprove a proposed cutting method not herein listed prior to acceptance of a bid.

6. Measurement of the area treated by Global Positioning System (GPS) as each unit is completed. Note: All

GPS measurements are taken on the horizontal plane not “slope” acreage.

C.2.2 - CONTRACTOR WILL FURNISH

1. Cutting equipment and any and all necessary parts or equipment to maintain the tools in a safe operating condition.

2. Transportation for equipment and operators to and from the site.

3. Repair and maintenance of equipment.

4. An English speaking authorized representative on site at all times when working.

C.2.3 - ACCESS

Access is provided to the project location off Fremont County Road 212. Souhwest of Poncha Springs, CO on to lands managed by the Bureau of Land Management (see J.1 Pass Creek Vicinity Map).

C.2.4 – OPERATIONS PLAN

Prior to the commencement of operations, the Contractor shall obtain from the COR written approval of a written operations plan commensurate with the terms and conditions of the contract which shall include measures needed to assure protection of the environment and watershed. All thinning and clearing shall be done in accordance with the plan.

C.2.4.1 - Work must be done in a systematic manner, beginning at one end of the project area and working through it in a logical manner prescribed in the operations plan.

C.2.4 CAMPING AND WORKSITE CONDITIONS

C.2.4.1 The contractor or his employees, upon documented permission from the CO/COR, may establish temporary work camps on public lands administered by the Bureau of Land Management. Camps shall be kept tidy and free of refuse. These camps may consist of mobile trailers, pickup campers, tent trailers, or tents. The contractor will be required to rehabilitate the camping area to the satisfaction of the CO/COR. Camps are subject to all fire restrictions placed by state, county or federal authorities.

C.2.4.2 MIGRANT SEASONAL AGRICULTURAL WORKERS PROTECTION ACT REGISTRATION

As set forth in Title 29, Part 500 of the Code of Federal Regulations, Migrant and Seasonal Agricultural Worker Protection, the Contractor shall maintain all necessary U.S. Department of Labor registrations during the performance period of this contract. Failure to maintain a valid registration is grounds for termination of this contract.

In compliance with the Migrant and Seasonal Agricultural Worker Protection Act, the Contractor shall provide the following to meet minimum safety and health standards for housing employees when camping on Federal lands:

a. A shelter to provide protection from the elements. Where heat adequate for weather conditions is not provided, other arrangements should be made to protect the workers from the cold.

b. Sanitary facilities for storing food. Ice chests or coolers, with ice supply made from potable water replenished as necessary, to meet the requirement for storage of perishable food items.

c. An adequate and convenient potable water supply, approved by the appropriate health authority, in each camp for drinking and cooking purposes. As an alternative, commercial bottled water may be used.

d. Toilet and hand washing facilities adequate for the capacity of the camp, at not less than a 1:15 ratio, supplied with adequate toilet paper. Such facilities shall be maintained in a sanitary condition and shall be on site and serviceable prior to any camping.

e. Fly-tight, rodent-tight, impervious, cleanable or single service containers to be used for the storage of garbage. Such containers shall be kept clean and emptied when full.

f. Basic first aid supplies under the charge of a person trained to administer first aid.

g. A laundry tray or tub for every 30 workers, or transportation, at least weekly, to a commercial Laundromat for all workers.

C.2.4.3 Biomass Removal:

Pursuant to 48CFR1437 (as amended in the Federal Register / Vol. 69, No. 166 / Friday, August 27, 2004) biomass resulting from this contract may be purchased from the BLM.

1. The contractor may remove and utilize woody biomass if:

(a) Project work is progressing as scheduled; and

(b) Removal is completed before contract expiration

2. To execute this option, the contractor must submit a written request to the Government.

3. Following receipt of the written request, and if appropriate, the Government and the contractor will negotiate and execute a separate timber/vegetative sales contract. Payment under this sales contract must be at a price equal to or greater than the appraised value before the removal of any woody biomass. The contractor must make any appropriate payment specified in this timber/vegetative sales contract.

4. The contractor must treat any woody biomass not removed in accordance with the specifications in the service contract.

5. The sales contract and service contract are severable; default or termination under either does not remove the contractor from payment or performance obligations under the other contract.

C.2.5 - COR/PI

COR/PI Jeremiah Moore Forester-BLM Office (719) 269-8576 Cellular (719) 393-2514

C.2.6 - ENVIRONMENTAL CONSIDERATIONS

C.2.6.1 - Surface Conditions - Crew carriers (vehicles) shall not be operated when the road is muddy or if on site moisture (rain/snow/hail/etc.) events exceed 0.25 inch in 1 hour or .75" in 24 hours, the COR may require a halt to traffic until the roads dry enough (or freeze) so that damage by vehicles does not occur. When/If such conditions are encountered, the Contractor shall stop work and immediately notify the COR/PI.

C.2.6.2 - Any damage to roads caused by the contractor will be repaired by the contractor to the satisfaction of the COR.

C.2.6.3 - Contractor shall clean-up all generated liter and dispose of it at an approved sanitary landfill or other location and in a manner approved by the CO/COR.

C.2.6.4 - To avoid the taking of a nest and disruption of the nesting season, no cutting will be allowed from

May 15 to July 15.

C.2.7 FEDERAL HOLIDAYS

No closures related to Federal holidays

C.2.8 - FIRE STIPULATIONS

C.2.8.1. Fire Period and Closed Season

Required tools and equipment shall be kept in serviceable condition and immediately available for initial attack on fires.

C.2.8.2. Substitute Measures

The Contracting Officer Representative may by written notice authorize substitute measures or equipment or may waive specific requirements during periods of low fire danger.

C.2.8.3. Emergency Measures

The Bureau of Land Management may require emergency measures, including the necessary shutting down of equipment or portions of operations in the project area during periods of fire emergency created by hazardous climatic conditions or when the implementation of Fire Restrictions require.

C.2.8.4. Fire Control

The Contractor shall, independently and in cooperation with the BLM, take all reasonable action to prevent and suppress fires in the project area. Independent initial action shall be prompt and shall include the use of all personnel and equipment available in the project area.

For the purpose of fighting wildland fires on or in the vicinity of the project, which are not caused by the Contractor's operations, the Contractor shall place employees and equipment temporarily at the disposal of the BLM. Any individual hired by the BLM will be employed in accordance with the Interagency Pay Plan for Emergency Firefighters. The BLM will compensate the Contractor for equipment rented, at firefighting equipment rates common in the area.

C.2.8.5. Compliance with State Forest Laws

Listing of specific fire precautionary measures herein is not intended to relieve the Contractor in any way from compliance with the State Fire Laws covering fire prevention and suppression equipment, applicable to operations under this contract, permit or license.

C.2.8.6. Fire Precautions

Specific fire precautionary measures are as follows:

a. Smoking and Open Fires

The Contractor shall not allow open fires on the project area without advance permission in writing from the Contracting Officer Representative.

Unless restricted by State Law or Federal Regulations, smoking shall be permitted only in such portions of the project area that are free of flammable material. Smokers shall smoke in such a position that any burning material will fall within a cleared area, and shall extinguish and press out in mineral soil all burning material before leaving the cleared area.

b. Fire Extinguishers and Equipment, on Trucks, Tractors, etc.

All power-driven equipment operated by the Contractor on public land, except portable fire pumps, shall be equipped with one fire extinguisher having a UL rating of at least 5 B, C and one "D" handled or long handled round point shove.

In addition, each motor patrol, truck and passenger-carrying vehicle shall be equipped with a double-bit axe or Pulaski, 3-1/2 pounds or larger.

Equipment shall be kept in a serviceable condition and shall be readily available.

c. Power Saws

Each gasoline power saw operator shall be equipped with a pressurized chemical fire extinguisher of not less than 8-ounce capacity by weight, and one long handled round point shovel, size "O" or larger. The extinguisher shall be kept in possession of the saw operator at all times. The shovel shall be accessible to the operator within 1 minute.

d. Extinguishers

One refill for each type or one extra extinguisher sufficient to replace each size extinguisher required on equipment shall be safely stored in the fire tool box or other agreed upon place on the project area that is protected and readily available.

e. Spark Arresters and Mufflers

Each internal combustion engine shall be equipped with a spark arrester meeting either (1) USDA Standard 5100- 1a, or (2) appropriate Society of Automotive Engineers (SAE) recommended practice J335(b) and J350(a) as now or hereafter amended unless it is:

(1) Equipped with a turbine-driven supercharger such as the turbocharger. There shall be no exhaust bypass.

(2) A passenger carrying vehicle or light truck, or medium truck up to 40,000 GVW, used on roads and equipped with a factory designed muffler complete with baffles and an exhaust system in good working condition.

(3) A heavy duty truck, such as a dump or log truck, or other vehicle used for commercial hauling, used only on roads and equipped with a factory designed muffler and with a vertical stack exhaust system extending above the cab.

Exhaust equipment described in this Subsection, including spark arresters and mufflers, shall be properly installed and constantly maintained in serviceable condition.

C.2.8.7. Additional Fire Precautions

If determined that fire danger indices as displayed in the National Fire Danger Rating System for a given area are exceeding the .90 percentile for Energy Release Component and Burning Index the Contractor will be required to:

a. Partial Hoot owl - The following may operate only between the hours of ½ HOUR BEFORE SUNRISE and 2 P.M. local time:

(1) power saws, except at loading sites

(2) welding or cutting of metal

(3) tractor or other mechanized roller crushing, hydro-axing, dozer piling operations

(4) mechanized loading and hauling

(5) any other spark-emitting operation not specifically mentioned

b. Additional Fire Precautionary Measure 1 - Tank Truck

The Contractor shall provide a tank truck or trailer, containing not less than 300 gallons of water, during yarding, loading, land clearing, right-of-way clearing, roller crushing, hydro-axing, and mechanical treatment of slash.

Such tank truck or trailer shall be maintained in a serviceable condition and located within 10 minutes, round trip, from each project area during fire period and closed season.

The tank truck or trailer shall be equipped with a pump capable of discharging 20 gallons of water per minute, using a 1/4 inch nozzle tip, through a 50 foot length of rubber lined hose. In addition, 500 feet of serviceable fabric jacket rubber lined hose of not less than 1 inch outside diameter, fitted with a nozzle capable of discharging a straight stream of 1/4 inch diameter and a spray pattern shall be immediately available for use. The tank, pump and at least 250 feet of hose and nozzle shall be connected and ready for use at all times.

If a trailer is used, it shall be equipped with a hitch to facilitate prompt movement. A serviceable tow vehicle shall be immediately available for attachment to the trailer and must meet the time requirements stated above. Such truck or trailer shall be equipped to operate for a minimum of 8 hours. Tank truck or trailer shall be available from the start of work to the end of the Fire Watch/Fire Security service.

c. Fire Security

The Contractor shall designate a person who shall perform fire security services listed below on the project area and vicinity. The designated person shall be capable of operating the Contractor's communications and firefighting equipment specified in the contract, excluding helicopters, and of directing the activities of the Contractor's personnel on forest fires. In lieu of having the designated person perform the required supervisory duties, the Contractor may provide another person meeting the qualifications stated above to direct the activities of the Contractor's personnel and equipment during all firefighting activities.

Services described shall be for at least 2 HOURS from the time the Contractor's Operations are shut down. For the purposes of this provision, personnel servicing equipment and their vehicles or who are engaged in cutting or welding metal are not considered on fire security.

Fire security services shall consist of moving throughout the operation area or areas constantly looking, reporting and taking suppression action on any fires detected. Where possible, the designated person shall observe inaccessible portions of remote operating areas from vantage points within or adjacent to project work.

d. Communications

The Contractor shall provide adequate two-way communication facilities to report a fire to Bureau of Land Management within 15 minutes of detection. FCC Regulations prohibit commercial use of Citizen Band (CB) radios. (CB's are not considered adequate two-way communications.)

Such communications shall be operable during periods of operation of power-driven equipment, including the time fire security is required.

8. General Shutdown-all Operations Suspended

If fire danger is severe, the Contractor will be asked to suspend work.

C.2.9 - HAZARDOUS MATERIALS

C.2.9.1 Use of Hazardous Materials and/or petroleum products requires that all appropriate State and Federal Regulations be complied with including, but not limited to, Safety Data Sheets (SDS) on hand and use of necessary Personal Protective Equipment (PPE).

C.2.9.2. On-site disposal of Hazardous Materials or Waste including hydrocarbons is not authorized. On-site disposal will subject the contractor to at least the cost of reclamation and the appropriate disposal of contaminated soil.

C.2.9.3. Incidental (de minimus) leaks from fittings, gaskets or ruptured hoses will not subject the contractor to remedial requirements. They will be considered to be normal and unavoidable losses. Continual leaks will be noted on inspection reports and correction through maintenance required.

C.2.9.4. Maintenance and repair operations that require the draining of engines or hydraulic systems may be conducted on site only if the fluids are captured, containerized, and removed from public lands for proper disposal.

C.2.10 - PROTECTION

The contractor is required to protect cadastral survey markers (brasscaps), bench marks, project markers, and other markers and stakes from damage or removal. In case of destruction or removal by the contractor, they will be replaced by the government and the actual cost of replacement deducted from payments due the contractor.

C.2.11 - REMEASUREMENT

Re-measurement of the acreage under a task order will be made upon written request by the Contractor. The written request must be made within 10 calendar days after completion of the work. If measurement indicates a difference of not more than 5 percent from the original measurement, the contractor shall pay the actual cost of the Re-measurement.

Payments will be based on the second measurement where the difference between measurements is more than 5 percent. Where the difference is less than 5 percent the results of the first measurement will be used.

C.2.12 - ROAD MAINTENAINCE

There is no intent in this contract to require road maintenance except to repair any damage that occurs by the contractor on non-county roads or by those in his employ. Should damage occur, sections C.2.12.1 & C2.12.2 will apply.

C.2.12.1 The contractor shall maintain the cross section of dirt or graveled roads as existed prior to this contract by blading and shaping the road surface and shoulders. Banks shall not be undercut. Established berms shall be maintained and additional berms shall be placed where needed to protect fills as directed by the COR/PI.

C.2.12.2 The contractor shall perform all road clean-up including removal of bank slough, slides, and fallen timber, which can practicably be accomplished by a motor patrol grader equipped with a front end blade, rubber-tired front end bucket loader, or comparable equipment, and by the use of hand tools. When working conditions dictate end haul of material, the distance and the quantity of material required to be moved shall be limited to what is reasonable and practicable without the use of additional equipment.

C.2.12.3 There shall be no snow plowing without prior approval of the CO/COR

C.2.13 - SAFETY

C.2.13.1 Safety Plan Required The Contractor shall prepare a Safety Plan that addresses the specific hazards of the work site and shall include working in areas of dead trees and falling debris. The Contractor shall identify the specific conditions that she/he considers is a hazard. The Safety Plan shall also address the personal protective equipment and mitigating measures the Contractor will employ to increase safety on the worksite. Additionally, a plan of action for an emergency event shall be included in the Safety Plan.

C.2.14 - INJURIES AND DAMAGE

The Contractor, in his operations under this contract, shall not do or omit to do anything by which act or omission any person or property may be injured or damaged and shall indemnify and save the United States harmless from any claim, demand, action, or damages on account of any personal injury or property damage arising by reason of anything done or omitted to be done by the Contractor, his contractors, subcontractors, or the employees of any of them.

C.2.15 - SIMULTANEOUS USE OF AREA

If the CO or Field Office Manager determines that other uses of the contract area will not seriously interfere with the operations of the contractor, he may issue permits, leases, or contracts for the simultaneous use of the contract area by others.

C.2.16 - SPARK ARRESTERS

It is prohibited to operate or use any internal or external combustion engine, on any timber, brush, or grass covered land, including trails traversing such land, without a spark arrester maintained in effective working order and meeting guidelines set forth in National Wildfire Coordinating Group Publication NFES 1363 and 2363.

C.2.17 - STATUS REPORT

Provided an onsite visit has not occurred during the period, the contractor is required to report status of work when any special situations or problems are encountered or once a week (whichever is less). These reports may be made by telephone to the PI/COR.

In the event of extreme weather the Contracting Officer will determine the best course of action based on comments from both the Contractor and PI/COR.

C.2.18 - ARCHAEOLOGICAL OR CULTURAL DISCOVERIES

If in connection with operations under this contract the Contractor, his subcontractors, or the employees of any of them, discovers, encounters, or becomes aware of any objects or sites of cultural value on the contract area such as historical or prehistorical ruins, human remains, graves or grave markers, fossils, or artifacts, the Contractor shall immediately suspend all operations in the vicinity of the cultural value and shall notify the COR of the findings. Operations may resume at the discovery site upon receipt of written instructions and authorization by the COR.

C.3 - CONTRACTOR QUALITY CONTROL INSPECTION SYSTEM

The Contractor shall propose and adopt a quality control inspection system to ensure that the work is progressing in compliance with specifications. Complete records of all inspection work performed by the Contractor shall be maintained and made available to the Government during the contract performance.

The following is an example that may be used or the contractor may propose their own:

Inspections will be made on a series of 1/20th acre (26’4” feet radius) plots located at predetermined intervals across each work unit. Sufficient plots will be taken to obtain at least one percent sample of the work unit. The plots are to determine if the requirements of section C.1.4 were met.

Each inspection plot will be subdivided into four (4) quadrants based on cardinal directions. Each quadrant will be evaluated for compliance with the intent of the contract specifications as stated in Section C that pertains to this individual treatment. If two (2) or more quadrants fail to comply, the plot will fail.

Work quality percentages are derived from data developed from inspection plots. The total number of satisfactory plots divided by the number of plots inspected determines the quality rate. This rate multiplied by 100 provides the work quality percentage.

Example: Number of plots inspected 25 Number of satisfactory plots 23 23 divided by 25 92 Work Quality Percentage 92%

C.4 - GOVERNMENT INSPECTIONS

C.4.1 The Government will make periodic inspections as a basis for payments and recommendations for adjustments in work quality while work is in progress.

C.4.2 When a succinct area (unit) is complete and ready for inspection, the contractor shall request a final inspection.

Inspection requests shall be in writing and pursuant to FAR 52.246-4 shall include results of Contractor’s quality inspections. Inspection of completed units will not occur until such notification is received. Inspections will be completed within ten (10) calendar days after the notice is received for each item. If a formal request for an item inspection is within the ten (10) working days since the previous request, the time will not start until the time for the previous inspection expires.

C.4.3 Inspections will be made on a series of 1/20 acre plots (26’4” radius) located at predetermined intervals across the work unit. Sufficient plots will be taken to obtain at least a one percent (1%) sample of the treated area. Inspection plots will not be taken in the reserve areas.

C.4.4 Each inspection plot will be divided into 4 equal quadrants. Each quadrant will be evaluated for compliance with all contract specifications. Quadrants meeting all contract specifications will receive 3 points. Quadrants found to have one contract violation will receive 2 points. Quadrants found to have two or more contract violations will receive no points.

Any quadrant having a cut or damaged conifer leave tree will receive no points. A maximum of 12 points is possible for each plot.

C.4.5 The PI will also check for cut or damaged leave trees between plots.

C.4.6 The following information will be recorded for each plot inspected:

a. Number of leave trees on the plot, was thinning met as outlined in C.1.4

b. Number of cut or damaged leave trees or other trees specifically designated not to be cut or damaged in each quadrant.

c. Quadrants where stumps exceed maximum height.

d. Quadrants where slash is not within the specifications outlined in C.1.4.5.

C.4.7 - Work Quality Percentage

C.4.7.1 - The work quality percentage is derived from data developed from inspection plots.

C.4.7.2 - Work quality is determined by dividing the total number of points earned by the total number of points possible (12 x number of plots taken). This rate multiplied by 100 equals the work quality percentage.

EXAMPLE:

Number of plots inspected - 25

Total points possible (12 x 25) - 300

Total points earned - 267

WQP - (267/300) x 100 - 89%

C.5 -ACCEPTANCE

C.5.1 Work will be accepted or rejected on a unit basis.

C.5.2 Acceptable Quality Level (AQL) - A minimum AQL of 85 percent WQP is required.

C.5.3 - Unsatisfactory Work Quality

C.5.3.1 - Based on inspection results, if units fall below the AQL of 85 percent or if the cut/damaged tree percent exceeds five, the CO will immediately notify the Contractor in writing and instruct the Contractor to improve the quality of the work. If the quality of the work is not raised to the AQL of 85 percent or the cut/damaged tree percent reduced to five or less after written notification, the CO may issue a suspend work order to resolve the problem, during which time contract performance time will continue to run

C.5.3.2 - If lodged trees, high stumps, or untreated surplus vegetation are the primary reason for unsatisfactory work, the area may be reworked to obtain satisfactory work quality.

C.6 - REINSPECTION

When units fall below the AQL of 85 percent, rework may be required. When instructed by the COR, the Contractor shall rework the unit for reinspection by the Government. If the unit again fails to meet the AQL of 85 percent, the CO has the option of accepting the unit at the work quality percent calculated from inspection plots or of ordering the Contractor to rework the unit again. If the CO elects to accept the unit at the work quality percent calculated after rework, the Contractor will be paid based on the results of the reinspection. The Contractor shall be charged for all the Government's reinspection costs.

C.7 - PAYMENT

Payment will be based on the Government's inspection results. The Contractor's inspection results are to be used as a guide for the Contractor's use in complying with contract specifications and not as a basis for payment. Payment will be made for completed units, for the actual number of acres completed, inspected and accepted by the Government, less the adjustment in payment based on the work quality level percentage, if any. If the work quality level equals or exceeds 95 percent before rework, full payment (100%) will be made for the number of acres inspected and accepted by the Government on the completed units. Units achieving a work quality level of 85-94 percent will be paid at that percentage rate. If units are accepted which do not meet the AQL of 85 percent, payment will be made at a rate determined by multiplying the actual inspection percentage by the bid price.

Unit Number Total Acres Unit 1 80

PART I - THE SCHEDULE

SECTION H - SPECIAL CONTRACT REQUIREMENTS

H. 1 - KEY PERSONNEL

H.1.1 The Contractor shall assign to this contract key personnel that list may include the following:

CONTRACTOR REPRESENTATIVE

FOREMAN

INSPECTOR

H.1.2 The Contractor shall make no substitutions of key personnel without notifying the Contracting Officer within a reasonable timeframe and in advance, and shall submit justification (including proposed substitutions) in sufficient detail to permit evaluation of the impact on the contract. Proposed substitutes should have comparable qualifications to those of the persons being replaced.

H.1.3 The Contractor shall make no diversion of key personnel without the written consent of the Contracting Officer.

H.1.4 The contract will be modified to reflect any approved changes of key personnel.

H.1.5 The Contractor's contractor representative shall be fully conversant in the English language.

H.2 - PREWORK CONFERENCE

Prior to commencement of work, the Contractor shall attend a meeting to discuss the contract terms, work performance requirements, and safety. Also at this meeting such items as work progress schedule, quality control, camping/worksite plan, and fire prevention plans shall be finalized in writing.

H. 3. SAFETY PLAN

The Contractor shall prepare a Safety Plan that addresses the specific hazards of the work site and shall include working in areas of falling debris. The Contractor shall identify the specific conditions that she/he considers is a hazard. The Safety Plan shall also address the personal protective equipment and mitigating measures the Contractor will employ to increase safety on the worksite. Additionally, a plan of action for an emergency event shall be included in the Safety Plan. (See also C.2.13.1)

SECTION C - CONTRACT CLAUSES

C.1 CONTRACT TERMS AND CONDITIONS – COMMERCIAL PRODUCTS AND

COMMERCIALS SERVICES. FAR 52.212-4 (NOV 2023)

Addendum to 52.212-4:

C.2 ADDENDUM TO FAR. FAR 52.212-4

DIAR 1452.201-70 AUTHORITIES AND DELEGATIONS (SEP 2011)

(a) The Contracting Officer is the only individual authorized to enter into or terminate this contract, modify any term or condition of this contract, waive any requirement of this contract, or accept nonconforming work.

(b) The Contracting Officer will designate a Contracting Officer's Representative (COR) at time of award. The COR will be responsible for technical monitoring of the contractor's performance and deliveries. The COR will be appointed in writing, and a copy of the appointment will be furnished to the Contractor. Changes to this delegation will be made by written changes to the existing appointment or by issuance of a new appointment.

(c) The COR is not authorized to perform, formally or informally, any of the following actions:

(1) Promise, award, agree to award, or execute any contract, contract modification, or notice of intent that changes or may change this contract;

(2) Waive or agree to modification of the delivery schedule;

(3) Make any final decision on any contract matter subject to the Disputes Clause;

(4) Terminate, for any reason, the Contractor's right to proceed;

(5) Obligate in any way, the payment of money by the Government.

(d) The Contractor shall comply with the written or oral direction of the Contracting Officer or authorized representative(s) acting within the scope and authority of the appointment memorandum. The Contractor need not proceed with direction that it considers to have been issued without proper authority. The Contractor shall notify the Contracting Officer in writing, with as much detail as possible, when the COR has taken an action or has issued direction (written or oral) that the Contractor considers to exceed the COR's appointment, within 3 days of the occurrence. Unless otherwise provided in this contract, the Contractor assumes all costs, risks, liabilities, and consequences of performing any work it is directed to perform that falls within any of the categories defined in paragraph (c) prior to receipt of the Contracting Officer's response issued under paragraph (e) of this clause.

(e) The Contracting Officer shall respond in writing within 30 days to any notice made under paragraph (d) of this clause.

A failure of the parties to agree upon the nature of a direction, or upon the contract action to be taken with respect thereto, shall be subject to the provisions of the Disputes clause of this contract.

(f) The Contractor shall provide copies of all correspondence to the Contracting Officer and the COR.

(g) Any action(s) taken by the Contractor, in response to any direction given by any person acting on behalf of the Government or any Government official other than the Contracting Officer or the COR acting within his or her appointment, shall be at the Contractor's risk.

(End of Clause)

--- End of Addendum to 52.212-4---

C.3 CONTRACT CLAUSES INCORPORATED BY REFERENCES. FAR 52.252-2 (FEB 1998)

This contract incorporates one or more clauses by reference, with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause may be accessed electronically at this/these address(es):

Federal Acquisition Regulation (FAR) Clauses: https://www.acquisition.gov/browse/index/far (FAR clauses begin with 52).

Department of the Interior Acquisition Regulation (DIAR) Clauses: https://www.acquisition.gov/diar.

52.204-9 Personal Identity Verification of Contractor Personnel (JAN 2011) 52.204-13 System for Award Management Maintenance (OCT 2018) 52.204-18 Commercial and Government Entity Code Maintenance (AUG 2020)

C.4 Contract Terms and Conditions Required to Implement Statutes or Executive Orders–

Commercial Products and Commercial Services. FAR 52.212-5 (JAN 2025)

(a) The Contractor shall comply with the following Federal Acquisition Regulation (FAR) clauses, which are incorporated in this contract by reference, to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services:

(1) 52.203-19, Prohibition on Requiring Certain Internal Confidentiality Agreements or Statements (JAN 2017) (section 743 of Division E, Title VII, of the Consolidated and Further Continuing Appropriations Act, 2015 (Pub. L. 113-235) and its successor provisions in subsequent appropriations acts (and as extended in continuing resolutions)).

(2) 52.204-23, Prohibition on Contracting for Hardware, Software, and Services Developed or Provided by Kaspersky Lab Covered Entities (DEC 2023) (Section 1634 of Pub. L. 115-91).

(3) 52.204-25, Prohibition on Contracting for Certain Telecommunications and Video Surveillance Services or Equipment. (NOV 2021) (Section 889(a)(1)(A) of Pub. L. 115-232).

(4) 52.209-10, Prohibition on Contracting with Inverted Domestic Corporations (NOV 2015).

(5) 52.232-40, Providing Accelerated Payments to Small Business Subcontractors (MAR 2023) ( 31 U.S.C. 3903 and 10 U.S.C. 3801).

(6) 52.233-3, Protest After Award (AUG 1996) (31 U.S.C. 3553).

(7) 52.233-4, Applicable Law for Breach of Contract Claim (OCT 2004) (Public Laws 108-77 and 108-78 ( 19 U.S.C. 3805 note)).

(b) The Contractor shall comply with the FAR clauses in this paragraph (b) that the Contracting Officer has indicated as being incorporated in this contract by reference to implement provisions of law or Executive orders applicable to acquisitions of commercial products and commercial services:

[Contracting Officer check as appropriate.]

__ (1) 52.203-6, Restrictions on Subcontractor Sales to the Government (JUN 2020), with Alternate I (NOV

2021) (41 U.S.C. 4704 and 10 U.S.C. 4655).

__ (2) 52.203-13, Contractor Code of Business Ethics and Conduct (NOV 2021) (41 U.S.C. 3509)).

__ (3) 52.203-15, Whistleblower Protections under the American Recovery and Reinvestment Act of 2009 (JUN

2010) (Section 1553 of Pub. L. 111-5). (Applies to contracts funded by the American Recovery and Reinvestment Act of 2009.)

__ (4) 52.203-17, Contractor Employee Whistleblower Rights (NOV 2023) ( 41 U.S.C. 4712); this clause does not apply to contracts of DoD, NASA, the Coast Guard, or applicable elements of the intelligence community—see FAR 3.900(a).

_XX_ (5) 52.204-10, Reporting Executive Compensation and First-Tier Subcontract Awards (JUN 2020) (Pub. L. 109-282) ( 31 U.S.C. 6101 note).

__ (6) [Reserved].

__ (7) 52.204-14, Service Contract Reporting Requirements (OCT 2016) (Pub. L. 111-117, section 743 of Div. C).

__ (8) 52.204-15, Service Contract Reporting Requirements for Indefinite-Delivery Contracts (OCT 2016) (Pub. L. 111-117, section 743 of Div. C).

_XX_ (9) 52.204-27, Prohibition on a ByteDance Covered Application (JUN 2023) (Section 102 of Division R of Pub. L.

117-328).

__ (10) 52.204-28, Federal Acquisition Supply Chain Security Act Orders—Federal Supply Schedules, Governmentwide Acquisition Contracts, and Multi-Agency Contracts. (DEC 2023) ( Pub. L. 115–390, title II).

__ (11) (i) 52.204-30, Federal Acquisition Supply Chain Security Act Orders—Prohibition. (DEC 2023) ( Pub. L. 115–390, title II).

__ (ii) Alternate I (DEC 2023) of 52.204-30.

_XX_ (12) 52.209-6, Protecting the Government's Interest When Subcontracting With Contractors Debarred, Suspended, Proposed for Debarment, or Voluntarily Excluded. (JAN 2025) ( 31 U.S.C. 6101 note).

__ (13) 52.209-9, Updates of Publicly Available Information Regarding Responsibility Matters (OCT

2018) ( 41 U.S.C. 2313).

__ (14) [Reserved].

__ (15) 52.219-3, Notice of HUBZone Set-Aside or Sole-Source Award (OCT 2022) ( 15 U.S.C. 657a).

__ (16) 52.219-4, Notice of Price Evaluation Preference for HUBZone Small Business Concerns (OCT 2022) (if the offeror elects to waive the preference, it shall so indicate in its offer) (15 U.S.C. 657a).

__ (17) [Reserved]

_XX_ (18) (i) 52.219-6, Notice of Total Small Business…