Signage Project Manual.pdf

FLORENCE-DARLINGTON TECHNICAL COLLEGE

MAIN CAMPUS SIGNAGE

GMC # ACST240010

PROJECT MANUAL

BID DOCUMENTS

JULY 23, 2024

997 Morrison Drive, Suite 102

Charleston, SC 29403

843.727.3140

MAIN CAMPUS SIGNAGE GMC Project Number: ACST240010 FLORENCE DARLINGTON TECHNICAL COLLEGE Bid Documents: 07/23/2024

FLORENCE, SOUTH CAROLINA

TABLE OF CONTENTS

PROJECT NAME: FDTC Main Campus Signage

PROJECT NUMBER: H59-6301-SG

SECTION NUMBER OF

PAGES

Table of Contents����������������������������������1

TECHNICAL SPECIFICATIONS

DIVISION 10 - SPECIALTIES

10 14 00 Signage��������������������������...����..9

ATTACHMENTS

Florence-Darlington Technical College, Design Package��������.��������..16

Florence-Darlington Technical College, Exterior Site Plan���������..�������2

FLORENCE, SOUTH CAROLINA

SIGNAGE 10 14 00 - 1 of 9

SECTION 10 14 00 � SIGNAGE

PART 1 - GENERAL

1.1 SUMMARY

A. Section Includes:

1. Exterior signage:

a. Monument cabinet signs.

b. Dimensional character signs.

c. Post-and-panel signs.

d. Post-and-cabinet signs.

2. Reinforced concrete bases with footings for monument signs.

3. Concrete footings for post and panel signs.

1.2 DEFINITIONS

A. Illuminated: Illuminated by lighting source integrally constructed as part of the sign unit.

1.3 ACTION SUBMITTALS

A. Product Data: For each type of product.

B. Shop Drawings: For signage.

1. Include fabrication and installation details; and attachments to other work.

2. Include details for:

a. Concrete base and footing construction; and attachment.

b. Existing brick base; and attachment.

c. Post-and-panel concrete footings

d. Existing wall/substrate construction and attachment.

3. Show sign mounting heights, supplementary supports and accessories.

4. Show message list, typestyles, graphic elements, and layout for each sign at least half size.

5. Show locations of electrical service connections.

6. Include diagrams for power, signal, and control wiring.

C. Samples for Verification: For each type of sign assembly showing components, and with the required finish(es), in manufacturer's standard size, unless otherwise indicated and as follows:

1. Monument Cabinet: Corner detail full at depth.

FLORENCE, SOUTH CAROLINA

SIGNAGE 10 14 00 - 2 of 9

2. Dimensional Characters:

a. Dimensional Characters: Half-size Sample each type of dimensional character.

b. Exposed Accessories: Full-size Sample of each accessory type.

3. Post-and-Panel:

a. Post-and-Panel Signs: Not less than 12 inches square, including corner and post.

b. Variable Component Materials: 8-inch Sample of each base material, character or graphic element, in each exposed color and finish not included in other Samples.

c. Exposed Accessories: Half-size Sample of each accessory type.

D. Product Schedule: For signage. Use same designations indicated on Attachments.

E. Delegated Design Submittal: For signs indicated in "Performance Requirements" Article.

1. Include structural analysis calculations for signs indicated to comply with design loads;

signed and sealed by the qualified professional engineer responsible for their preparation.

1.4 INFORMATIONAL SUBMITTALS

A. Qualification Data: For Installer and manufacturer.

B. Evaluation Reports: For post-installed anchors and power-actuated fasteners, from ICC-ES or other qualified testing agency acceptable to authorities having jurisdiction.

C. Sample Warranty: For special warranty.

1.5 CLOSEOUT SUBMITTALS

A. Maintenance Data: For signs to include in maintenance manuals.

1.6 QUALITY ASSURANCE

A. Manufacturer Qualifications: Manufacturer shall provide the following:

1. Executive Summary: Explaining who the company is and why they are a fit for the project.

2. Firm Profile: Showing number of offices, locations, number of employees, year of founding and number of active clients.

3. References: From similar clients including client name, contact person with title, email and phone number.

4. Project Team: List project specific team with educational background and experience.

Individual team members should have experience on similar projects and demonstrate expertise in Project Management, Engineering, Installation, Planning and Design.

5. Project Examples: Five project examples with photos for a similar scope.

6. Quality Management: Written description of company's quality management program.

7. Safety Management: Written description of company's safety program.

FLORENCE, SOUTH CAROLINA

SIGNAGE 10 14 00 - 3 of 9

8. Web Based Sign Management: Description and examples of web based sign management platform that will be used to manage final approvals and serve as a long term asset management platform.

9. Financial Statements: CPA reviewed financial statements showing the last 3 years of financial performance.

10. Material Samples: Project specific samples of all materials and colors within scope.

B. Installer Qualifications: An entity that employs installers and supervisors who are trained and approved by manufacturer.

1.7 FIELD CONDITIONS

A. Site Conditions: Survey site conditions. Graphically indicate and note grade conditions, and field measurements of adjacent construction such as, but not limited to, sidewalks, drives, parking and buildings.

B. Field Measurements: Verify locations of anchorage devices and electrical service embedded in permanent construction by field measurements before fabrication, and indicate measurements on Shop Drawings.

1.8 COORDINATION

A. Furnish templates and tolerance information for placement of sign-anchorage devices embedded in permanent construction.

B. Furnish templates for placement of electrical service embedded in permanent construction.

1.9 MAINTENANCE MATERIAL SUBMITTALS

A. Furnish extra materials, from the same product run, that match products installed and that are packaged with protective covering for storage and identified with labels describing contents.

1. Variable Component Materials: 12 replaceable text inserts and interchangeable characters (letters, numbers, and graphic elements) of each type.

2. Tools: One set(s) of specialty tools for assembling signs and replacing variable sign components.

1.10 WARRANTY

A. Special Warranty: Manufacturer agrees to repair or replace components of signs that fail in materials or workmanship within specified warranty period.

1. Failures include, but are not limited to, the following:

a. Deterioration of finishes beyond normal weathering.

b. Separation or delamination of sheet materials and components.

2. Warranty Period: Five years from date of Substantial Completion.

FLORENCE, SOUTH CAROLINA

SIGNAGE 10 14 00 - 4 of 9

PART 2 - PRODUCTS

2.1 PERFORMANCE REQUIREMENTS

A. Delegated Design: Engage a qualified professional engineer, as defined in Section 01 40 00 "Quality Requirements," to design sign structure and anchorage of base-supported, post-supported and wall-supported sign type(s) according to structural performance requirements.

B. Structural Performance: Signs and supporting elements shall withstand the effects of gravity and other loads within limits and under conditions indicated.

1. Uniform Wind Load: in accordance with International Building Code, 2021 Edition.

C. Thermal Movements: For exterior signs, allow for thermal movements from ambient and surface temperature changes.

1. Temperature Change: 120 degrees F (67 degrees C), ambient; 180 degrees F (100 degrees C), material surfaces.

D. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application.

2.2 SIGNAGE

A. Basis-of-Design Products: Subject to compliance with requirements, provide Takeform (www.takeform.net, 800-528-1398); products or comparable products, approved by the Architect, by one of the following.

1. ACE Sign Systems, Inc.

2. APCO Graphics, Inc.

3. ASI Sign Systems, Inc.

B. Description: See Attachments, to this specification section, for signage descriptions including, but not limited to, signage types, materials, finishes and colors, message schedules, text and typeface, dimensions, illumination requirements and locations.

2.3 MONUMENT CABINET SIGNS

A. Monument Cabinet Sign: Sign of cabinet (hollow-box) configuration; double-sided with smooth, uniform surfaces and support assembly; with message and characters having uniform faces, sharp corners, and precisely formed lines and profiles, as follows:

1. Materials: Aluminum, acrylic and vinyl.

2. Cabinet Size: As indicated on Attachments.

a. Profile: Square.

b. Corner Condition in Elevation: Square.

3. Illuminated/Nonilluminated: As indicated on Attachments.

FLORENCE, SOUTH CAROLINA

SIGNAGE 10 14 00 - 5 of 9

4. Aluminum Finish: Manufacturer�s standard baked-enamel or powder-coat finish.

a. Colors: As indicated on Attachments.

5. Surface-Applied Graphics: As indicated on Attachments.

6. Mounting: As indicated on Attachments including concrete base and footings.

2.4 DIMENSIONAL CHARACTERS

A. Cutout Characters: Characters with uniform faces; square-cut, smooth, edges; precisely formed lines and profiles; and as follows:

1. Character Material: Sheet or plate aluminum.

2. Character Height: As indicated on Attachments.

3. Thickness: As indicated on Attachments.

4. Finishes:

a. Manufacturer�s standard baked-enamel or powder-coat finish.

b. Overcoat: Manufacturer's standard baked-on clear coating.

c. Colors: As indicated on Attachments.

5. Mounting: Concealed studs with adhesive unless otherwise indicated or noted on Attachments.

2.5 POST-AND-PANEL SIGNS

A. Post-and-Panel Sign: Sign of single-panel configuration, both single-sided and double-sided; with smooth, uniform surfaces and support assembly; with message and characters having uniform faces, sharp corners, and precisely formed lines and profiles; and as follows:

1. Panel and Post Materials: Aluminum.

2. Sizes and Thicknesses: As indicated on Attachments.

a. Profile: Square.

3. Aluminum Finish: Manufacturer�s standard baked-enamel or powder-coat finish.

a. Colors: As indicated in Attachments.

4. Surface-Applied Graphics: As indicate on Attachments.

5. Installation: Direct burial or concrete footings as recommended by manufacturer.

2.6 POST-AND-CABINET SIGNS

A. Post-and-Panel Sign: Sign of cabinet (hollow-box) configuration; double sided with smooth, uniform surfaces and support assembly; with message and characters having uniform faces, sharp corners, and precisely formed lines and profiles; and as follows:

1. Cabinet and Post Material: Aluminum.

FLORENCE, SOUTH CAROLINA

SIGNAGE 10 14 00 - 6 of 9

2. Sizes and Thicknesses: As indicated on Attachments.

a. Profile: Square.

b. Corner Condition in Elevation: Square.

3. Aluminum Finish: Manufacturer�s standard baked-enamel or powder-coat finish.

a. Colors: As indicated in Attachments.

4. Surface-Applied Graphics: As indicate on Attachments.

5. Installation: Direct burial or concrete footings as recommended by manufacturer.

2.7 MATERIALS

A. Aluminum Sheet and Plate: ASTM B209, alloy and temper recommended by aluminum producer and finisher for type of use and finish indicated.

B. Aluminum Extrusions: ASTM B221, alloy and temper recommended by aluminum producer and finisher for type of use and finish indicated.

C. Acrylic Sheet: ASTM D4802, category as standard with manufacturer for each sign, Type UVF (UV filtering).

D. Vinyl Film: UV-resistant vinyl film of nominal thickness indicated, with pressure-sensitive, permanent adhesive on back; die cut to form characters or images as indicated on Attachments and suitable for exterior applications.

E. Paints and Coatings for Sheet Materials: Inks, dyes, and paints that are recommended by manufacturer for optimum adherence to surface and are UV and water resistant for colors and exposure indicated.

2.8 ACCESSORIES

A. Fasteners and Anchors: Manufacturer's standard as required for secure anchorage of signs, noncorrosive and compatible with each material joined, and complying with the following:

1. Use concealed fasteners and anchors unless indicated to be exposed.

2. For exterior exposure, furnish stainless steel devices unless otherwise indicated.

3. Exposed Metal-Fastener Components, General:

a. Fabricated from same basic metal and finish of fastened metal unless otherwise indicated.

b. Fastener Heads: For nonstructural connections, use flathead or oval countersunk screws and bolts with tamper-resistant Allen-head, spanner-head or slots unless otherwise indicated.

4. Sign Mounting Fasteners:

a. Concealed Studs: Concealed (blind), threaded studs welded or brazed to back of sign material, screwed into back of sign assembly, or screwed into tapped lugs cast integrally into back of cast sign material, unless otherwise indicated.

FLORENCE, SOUTH CAROLINA

SIGNAGE 10 14 00 - 7 of 9

B. Adhesive: As recommended by sign manufacturer.

C. Bituminous Paint: Cold-applied asphalt emulsion complying with ASTM D1187/D1187M.

2.9 FABRICATION

A. General: Provide manufacturer's standard sign assemblies according to requirements indicated.

1. Preassemble signs and assemblies in shop to greatest extent possible. Disassemble signs and assemblies only as necessary for shipping and handling limitations. Clearly mark units for reassembly and installation; apply markings in locations concealed from view after final assembly.

2. Mill joints to a tight, hairline fit. Form assemblies and joints exposed to weather to resist water penetration and retention.

3. Comply with AWS for recommended practices in welding and brazing. Provide welds and brazes behind finished surfaces without distorting or discoloring exposed side. Clean exposed welded and brazed connections of flux, and dress exposed and contact surfaces.

4. Conceal connections if possible; otherwise, locate connections where they are inconspicuous.

5. Internally brace dimensional characters for stability, to meet structural performance loading without oil-canning or other surface deformation, and for securing fasteners.

6. Provide rabbets, lugs, and tabs necessary to assemble components and to attach to existing work. Drill and tap for required fasteners. Use concealed fasteners where possible;

use exposed fasteners that match sign finish.

B. Post Fabrication: Fabricate posts designed for structural performance indicated and of lengths required for installation method indicated for each sign.

1. Aluminum Posts: Manufacturer's standard 0.125-inch- thick, extruded-aluminum tubing unless otherwise indicated, with brackets or slots to engage sign panels. Include post caps, fillers, spacers, junction boxes, access panels, reinforcement where required for loading conditions, and related accessories required for complete installation.

2. Direct Burial: Fabricate posts 36 inches longer than height of sign to permit direct burial or embedment in concrete foundations or concrete-filled postholes.

C. Brackets: Fabricate brackets, fittings, and hardware for bracket-mounted signs to suit sign construction and mounting conditions indicated. Modify manufacturer's standard brackets as required.

1. Stainless Steel Brackets: Factory finish brackets with No. 4 finish unless otherwise indicated.

2.10 GENERAL FINISH REQUIREMENTS

A. Protect mechanical finishes on exposed surfaces from damage by applying a strippable, temporary protective covering before shipping.

FLORENCE, SOUTH CAROLINA

SIGNAGE 10 14 00 - 8 of 9

B. Appearance of Finished Work: Noticeable variations in same piece are not acceptable. Variations in appearance of adjoining components are acceptable if they are within the range of approved Samples and are assembled or installed to minimize contrast.

C. Organic Produced Finishes: Apply to formed metal after fabrication but before applying contrasting polished finishes on raised features unless otherwise indicated.

2.11 ALUMINUM FINISHES

A. Baked-Enamel or Powder-Coat Finish: AAMA 2603 except with a minimum dry film thickness of

1.5 mils (0.04 mm). Comply with coating manufacturer's written instructions for cleaning, conversion coating, and applying and baking finish.

PART 3 - EXECUTION

3.1 EXAMINATION

A. Examine substrates, bases, areas, and conditions, with Installer present, for compliance with requirements for installation tolerances and other conditions affecting performance.

B. Verify that sign-support surfaces are within tolerances to accommodate signs without gaps or irregularities between backs of signs and support surfaces unless otherwise indicated.

C. Verify that electrical service is correctly sized and located to accommodate signs.

D. Proceed with installation only after unsatisfactory conditions have been corrected.

3.2 INSTALLATION � CABINET SIGNAGE

A. Preset Anchor Bolts: Set baseplate in position over anchor bolts projecting from concrete foundation, shim and support to prevent movement, place washers and nuts, and tighten. Fill shim space with nonshrink, nonmetallic grout, mixed and placed to comply with manufacturer's written instructions.

B. Drilled-in-Place Anchor Bolts: Set baseplate in position over concrete foundation, locate and drill anchor holes, shim and support to prevent movement, place washers and anchor bolts, and tighten. Fill shim space with nonshrink, nonmetallic grout, mixed and placed to comply with manufacturer's written instructions.

3.3 INSTALLATION - DIMENSIONAL CHARACTERS

A. General: Install signs using mounting methods indicated and according to manufacturer's written instructions.

1. Install signs level, plumb, true to line, and at locations and heights indicated, with sign surfaces free of distortion and other defects in appearance.

2. Before installation, verify that sign surfaces are clean and free of materials or debris that would impair installation.

FLORENCE, SOUTH CAROLINA

SIGNAGE 10 14 00 - 9 of 9

3. Corrosion Protection: Coat concealed surfaces of exterior aluminum in contact with grout, concrete, masonry, wood, or dissimilar metals, with a heavy coat of bituminous paint.

B. Mounting Methods:

1. Concealed Studs: Using a template, drill holes in substrate aligning with studs on back of sign. Remove loose debris from hole and substrate surface.

a. Masonry Substrates: Fill holes with adhesive. Leave recess space in hole for displaced adhesive. Place sign in position and push until flush to surface, embedding studs in holes. Temporarily support sign in position until adhesive fully sets.

b. Thin or Hollow Surfaces: Place sign in position and flush to surface, install washers and nuts on studs projecting through opposite side of surface, and tighten.

3.4 INSTALLATION - POSTS

A. Vertical Tolerance: Set posts plumb within a tolerance of 1/16 inch in 3 feet.

B. Direct-Burial Method:

1. Excavation: Excavate posthole to dimensions indicated. Reconstruct subgrade that is not firm, undisturbed, or compacted soil, or that is damaged by freezing temperatures, frost, rain, accumulated water, or construction activities by excavating an additional 12 inches, backfilling with satisfactory soil or well-graded aggregate, and compacting to original subgrade elevation.

2. Setting in Earth: Set post in position, support to prevent movement, and backfill with satisfactory soil or well-graded aggregate as recommended in writing by manufacturer.

Place and compact backfill in 6-inch lifts, compacting each lift.

3. Setting in Cast-in-Place Concrete: Set post in position, support to prevent movement, and place concrete in posthole indicated on Drawings.

3.5 ADJUSTING AND CLEANING

A. Remove and replace damaged or deformed characters and signs that do not comply with specified requirements. Replace characters with damaged or deteriorated finishes or components that cannot be successfully repaired by finish touchup or similar minor repair procedures.

B. Remove temporary protective coverings and strippable films as signs are installed.

C. On completion of installation, clean exposed surfaces of signs according to manufacturer's written instructions, and touch up minor nicks and abrasions in finish. Maintain signs in a clean condition during construction and protect from damage until acceptance by Owner.

END OF SECTION 10 14 00

Attachments:

- Florence-Darlington Technical College, Design Package, Version FLO0040 2110563 EXT Rev3, dated October 4, 2023.

- Florence-Darlington Technical College, Exterior Site Plan

Design Package

FLO0040_210563_EXT_Rev3

10 / 04 / 2023

Project:

Florence Darlington

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 1 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

120V Electrical Service Required

Verify Mounting Conditions

Site Survey Required

168.00”

Existing EMC Base Approximate Dimensions

144.00”

37.50"

4.00"

41.50"

141.00”

8.75"

Sign 81

Type 1 Double Sided, Internally Illuminated Monument Cabinet Mechanically Fasten to Existing Brick Base

QTY: 1

MAIN ENTRANCE

Alternate design option

A Painted, Routed Fabricated Aluminum Depth TBD based on existing cabinet depth to match PMS 2768 C / PMS 7405 C / CO104 White

Body

B 3/16” Transluscent Acrylic Backer w/ First Surface Applied Translucent Vinyl Graphic: Customer Supplied Artwork to match PMS 2768 C / PMS 7405 C / 7328 White

Logo

C Push-thru 3/4” Clear Acrylic, 1/2” Proud of Face Graphic: Customer Supplied Artwork 7328 White

Copy

D Painted, Fabricated Aluminum to match PMS 2768 C

Reveal

A

B

C

D

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 2 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

120V Electrical Service Required

Verify Mounting Conditions

Site Survey Required

112.00”

40.00"

PISGAH

ENTRANCE 4.37"

26.00"

Side A Side BProfile Left Profile Right

18.00"

16.00"38.00"

Sign 84

Sign 82 Message Schedule:

Sign 83

Type 1.1 Double Sided, Internally Illuminated Monument Cabinet Mechanically Fasten to Concrete Base

QTY: 3

ENTRANCE

DARLINGTON 3.75"

ENTRANCE

FLORENCE 3.75"

4.37"

4.37"

Typical

Side A

Side A

A Painted, Routed Fabricated Aluminum to match PMS 2768 C / PMS 7405 C / CO104 White

Body

B 3/16” Transluscent Acrylic Backer w/ First Surface Applied Translucent Vinyl Graphic: Customer Supplied Artwork to match PMS 2768 C / PMS 7405 C / 7328 White

Logo

C Push-thru 3/4” Clear Acrylic, 1/2” Proud of Face Graphic: Customer Supplied Artwork 7328 White

Copy

D Painted, Fabricated Aluminum to match PMS 2768 C / PMS 7405 C

Reveals

A

B

D D

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 3 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

Verify Mounting Conditions

Site Survey Required

MA

IN

ST

RE

ET

MA

IN

ST

RE

ET

DU

BA

RD

B

LV

D.

FL

OR

EN

CE

AV

E.

ST

IN

GE

RS

W

AL

K

DU

BA

RD

B

LV

D.

FL

OR

EN

CE

AV

E.

8.00'

48.00"

9.00'

3.00"

6.00"

Street ID

4.00"

Side A Side B Side A Side BProfileProfile

0.50"

4.37"4.37"

Sign 85, 86, 87 Street ID Sign 88, 89, 93, 94

Street ID Sign 90, 91, 92

Walk ID Sign 144, 145, 146 147, 148, 149, 150 151, 152, 153, 154 155, 156, 157

Type 2 Double Sided Post and Cabinet Direct Bury

QTY: 10

Type 6 Double Sided Post and Cabinet Direct Bury

QTY: 14

ST

IN

GE

RS

W

AL

K

Message Schedule:

Type 2

A Painted, 4” Deep Fabricated Aluminum to match PMS Medium Blue C

Wrap

B Painted, 1/2” Flat Cut Aluminum Font: Bebas Neue Pro Bold CO104 White

Copy

C Painted, 3” Square Aluminum to match PMS 7405 C

Post

A

B

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 4 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

120V Electrical Service Required

Verify Mounting Conditions

Site Survey Required

76.00"

40.00"

Side A Side BProfile

12.00"

10.00"

10.00"

1.50"

BLDG 100

PARKING

BLDG 5000

PARKING

Sign 97

3.00"

A

D

C

PMS 2612 C

PMS 7685 C

PMS 7409 C

PMS 368 C

PMS 7405 C

PMS 1795 C

Vinyl Colors

A Painted, Routed 12” Deep Fabricated Aluminum to match PMS 2768 C

Body

C Painted, Fabricated Aluminum to match PMS 2768 C / PMS 7405 C

Reveals

B Not Used

Illuminated Copy

D First Surface Applied Printed Reflective Vinyl Font: Helvetica LT Std Bold Condensed to match Vinyl Colors / 280-10 White Reflective

Non-Illuminated Copy

Type 3 Double Sided, Non-Illuminated Monument Cabinet Mechanically Fasten to Concrete Base

QTY: 10

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 5 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

120V Electrical Service Required

Verify Mounting Conditions

Site Survey Required

BLDG 5000

PARKING

Message Schedule:

Type 3

BLDG 100

PARKING

EXIT TO

HIGHWAY 52

BLDG SiMT

PARKING

EXIT TO

PISGAH RD.

Sign 98

Sign 106 Side A Side B

EXIT TO

HIGHWAY 52

Sign 100

DELIVERIES

BLDG 100-300

5000 / 7000

PARKING

thru

BLDG

100 / 5000

PARKING

EXIT TO

HIGHWAY 52

Sign 103

BLDG 600 / 650

7000 / SiMT

PARKING

thru

BLDG SiMT

PARKING

BLDG SiMT

PARKING

BLDG

100 / 5000

PARKING

Sign 107

PARKING

BLDG SiMT

PARKING

BLDG SiMT

PARKING

BLDG SiMT

PARKING

BLDG SiMT

PARKING

EXIT TO

PISGAH RD.

Sign 108

BLDG SiMT

PARKING

BLDG SiMT

PARKING

Sign 114

PARKING

ONE WAY

DO NOT ENTER

BLDG 100

PARKING

Sign 121 Sign 211

PARKING

BLDG SiMT

PARKING

PARKING

BLDG 100 / 200

300 / 5000

PARKING

BLDG 100 / 200

300 / 5000

PARKING

BLDG 600 / 650

PARKING

BLDG 600 / 650

PARKING

BLDG

100 / 5000

PARKING

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 6 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

120V Electrical Service Required

Verify Mounting Conditions

Site Survey Required

Side A Side BProfile

12.00"

10.00"

10.00"

1.50"

Type 3.1 Double Sided, Internally Illuminated Monument Cabinet Mechanically Fasten to Concrete Base

QTY: 5

BLDG 100 / 300

600 / 650 / 5000 7000 / SiMT

40.00"

PARKING

thru

BLDG

100 / 5000

PARKING

92.00"

3.00" BLDG

100 / 5000

PARKING

EXIT TO

HIGHWAY 52

Sign 96

A

B

C

A Painted, Routed 12” Deep Fabricated Aluminum to match PMS 2768 C

Body

C Painted, Fabricated Aluminum to match PMS 2768 C / PMS 7405 C

Reveals

B Push-thru 3/4” Clear Acrylic, 1/2” Proud of Face Font: Helvetica LT Std Bold Condensed to match Vinyl Colors / 230-43 Light Tomato Red / 7328 White

Illuminated Copy

D First Surface Applied Printed Reflective Vinyl Font: Helvetica LT Std Bold Condensed to match Vinyl Colors / 280-10 White Reflective

Non-Illuminated Copy

PMS 2612 C

PMS 7685 C

PMS 7409 C

PMS 368 C

PMS 7405 C

PMS 1795 C

Vinyl Colors

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 7 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

120V Electrical Service Required

Verify Mounting Conditions

Site Survey Required

Message Schedule:

Type 3.1

BLDG 100-300

5000 / 7000

DELIVERIES

PARKING

thru

BLDG

100 / 5000

PARKING

BLDG 100 / 200

300 / 5000

PARKING

thru

BLDG

100 / 5000

PARKING

EXIT TO

HIGHWAY 52

Sign 99

BLDG

100 / 5000

PARKING

Sign 101

Side A Side B

Sign 104

BLDG 600 / 650

7000 / SiMT

PARKING

thru

BLDG 7000

PARKING

BLDG

100 / 5000

PARKING

Sign 102

BLDG 600 / 650

SiMT

PARKING

thru

BLDG 7000

PARKING

BLDG

7000 / 900

PARKING

BLDG

7000 / 900

PARKING

BLDG

600 / 650 / SiMT

PARKING

BLDG

100 / 5000

PARKING

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 8 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

Verify Mounting Conditions

Site Survey Required

VIP & VISITOR

PARKING

24.00"

40.00"

84.00"

Side A Side BProfile

Type 4 Double Sided Post and Panel Direct Bury

QTY: 23

2.00" 28.00"

Sign 110, 112, VIP & VISITOR

PARKING

Sign 111

Typical

EMPLOYEE

PARKING

Sign 115, 116

EMPLOYEE

PARKING

Sign 117, 118

Sign 128, 131

EMPLOYEE

PARKING

STUDENT

PARKING

Sign 119, 120

STUDENT

PARKING

Sign 126

STUDENT

PARKING

Sign 122, 123, VISITOR

PARKING

Sign 125

STUDENT

PARKING

Sign 133

VIP & VISITOR

PARKING

Sign 134

STUDENT

PARKING

Sign 127

VISITOR

PARKING

Sign 129, 130

EMPLOYEE

PARKING

STUDENT

PARKING

Sign 132

Side A Side B

Message Schedule:

Type 4

4.20"

44.00"

A Painted .125” Aluminum to match PMS 2768 C

Panel

D Painted, 2” Square Aluminum to match PMS 7405 C

Post

B First Surface Applied Reflective Vinyl Font: Bebas Neue Pro Bold 280-10 White Reflective

Copy

C First Surface Applied Printed Reflective Vinyl Font: Helvetica LT Std Bold Condensed to match Vinyl Colors / 280-10 White Reflective

Parking Circle

A

B

C

D

PMS 2612 C

PMS 7685 C

PMS 7409 C

PMS 368 C

PMS 7405 C

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 9 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

Verify Mounting Conditions

Site Survey Required

RESERVED

VIP

Campus Tour Guest Parking

Only

18.00"

12.00"

88.00"

2.00"

CAMPUS MAP

40.00"

60.50"

10.00"

10.00"

4.00"

87.50"

2.00"

64.00"

Hinge frame w/ removable panel

5.00"

Sign 135, 136, 137, 138, Sign TBD

Type 5 Double Sided, Non-Illuminated Monument Cabinet Mechanically Fasten to Concrete Base

QTY: 3

Type 10 Single Sided Post & Panel Direct Bury

QTY: 2

A Painted, Routed 12” Deep Fabricated Aluminum to match PMS 2768 C

Body

C Painted, Fabricated Aluminum to match PMS 2768 C / PMS 7405 C

Reveals

B Painted, 1/2” Flat Cut Aluminum Font: Bebas Neue Pro Bold CO104 White

Copy

D Direct Print Graphic: Campus Map Artwork Required

Graphic

G Painted .125” Aluminum to match PMS 2768 C

Reserved Panel

I Painted 2” Square Aluminum to match PMS 2768 C /

PMS 7405 C

Post

H First Surface Applied Printed Reflective Vinyl Font: Helvetica LT Std Bold Condensed to match PMS 7405 C / 280-10 White Reflective

Copy

A

B

C

G

H

I

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 10 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

Verify Mounting Conditions

Site Survey Required

84.00"

40.00"

34.00"

5.50"

42.50"

4.00"

Type 7 Double Sided, Post and Panel Panel Count: Side A (2), Side B (2) Direct Bury

QTY: 7

Type 7.1 Double Sided, Post and Panel Panel Count: Side A (2), Side B (2) Direct Bury

QTY: 7

2.00"

Sign 159

Side A Side BProfile

44.00"

PARKING

BLDG SiMT

PARKING

BLDG SiMT

84.00"

40.00"

34.00"

42.50"

Sign 158

Side A Side B

44.00"

STINGERS WALK

PARKING

BLDG SiMT

STINGERS WALK

PARKING

BLDG 600

650 / 7000

Typical Copy:

1/2” Flat Cut

Aluminum Letters

A Painted .125” Aluminum to match PMS 2768 C / PMS Medium Blue C

Panel

D Painted, 2” Square Aluminum to match PMS 7405 C

Post

B First Surface Applied Reflective Vinyl Font: Bebas Neue Pro Bold 280-10 White Reflective

Stinger Copy

A A

B

C

D

C

D

C First Surface Applied Printed Reflective Vinyl Font: Helvetica LT Std Bold Condensed to match Vinyl Colors / 280-10 White Reflective

Parking Circle

PMS 2612 C

PMS 7685 C

PMS 7409 C

PMS 368 C

PMS 7405 C

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 11 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

Verify Mounting Conditions

Site Survey Required

Sign 162

Message Schedule:

Type 7

Message Schedule:

Type 7.1

Side A Side B

BLDG 7000

PARKINGPARKING

BLDG

600 / 650

Sign 165

PARKING

BLDG

200 / 300

Sign 163

PARKING

BLDG 100 / 200

300 / 5000

PARKING

BLDG 7000

Sign 160

PARKING

PARKING BLDG

SiMT / MBI

Sign 161

PARKING

Sign 164

PARKING

BLDG 7000BLDG

100 / 200 / 300

BLDG SiMT

BLDG 5000

Sign 166

BLDG

200 / 300

BLDG 5000

Sign 169 Sign 190

Sign 191

DELIVERIES

PHYSICAL PLANT

DELIVERIES

PHYSICAL PLANT

PARKING

BLDG

200 / 300

PARKING

BLDG 5000

Sign 167

PARKING

BLDG 5000

PARKING

BLDG 5000

Sign 210

BLDG

SiMT / MBI

BLDG SiMT

PARKING

PARKING

BLDG 300

BLDG 200

BLDG 100

PARKING

BLDG 7000

PARKING

PARKING

PARKING

PARKING

STINGERS WALK STINGERS WALK STINGERS WALK STINGERS WALK STINGERS WALK STINGERS WALK

STINGERS WALK STINGERS WALK STINGERS WALK STINGERS WALK STINGERS WALK STINGERS WALK

60.00"

Florence Darlington

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 12 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

120V Electrical Service Required

Verify Mounting Conditions

Site Survey Required

Side B

QTY: 6

Type 8: Option B Double Sided, Illuminated Monument Cabinet Mechanically Fasten to Concrete Base

Sign 168

A Painted, Routed 12” Deep Fabricated Aluminum to match PMS 2768 C

Body

C Painted, Fabricated Aluminum to match PMS 2768 C / PMS 7405 C

Reveals

B Push-thru 3/4” Clear Acrylic, 1/2” Proud of Face Font: Helvetica LT Std Bold Condensed to match PMS 7405 C / 7328 White

Illuminated Copy

D First Surface Applied Printed Vinyl Font: Helvetica LT Std Bold Condensed to match PMS 7405 C / 220-10 White

Non-Illuminated Copy

Profile

12.00"

1.50"

10.00"

10.00"

40.00"

STUDENT SERVICES

BOOKSTORE

ADMINISTRATIVE &

BUSINESS OFFICES

Side A

9.50"

2.39"

A

B

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 13 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

Verify Mounting Conditions

Site Survey Required

ADVISING CENTER

Side A Side B

Message Schedule:

Type 8

Sign 177

Sign 212

SiMT

ADVANCED

MANUFACTURING

CENTER

Sign 203, 205Sign 178

STUDENT SERVICES

BOOKSTORE

ADMINISTRATIVE &

BUSINESS OFFICES

PRINT SHOP

WELDING

LIBRARY

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 14 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

Verify Mounting Conditions

Wall Construction Details Required

Site Survey Required

SiMT

PHYSICAL PLANT

GOULD INCUBATOR

CEP

0.50" Flat Cut

Aluminum

Type 8.1 Dimensional Copy Stud Mount Flush to Building Fascia w/ Loctite PL Premium Construction Adhesive

QTY: 25

Sign 170, 171, 172 Sign 196, 198

Sign 173, 184, 185, 186 Sign 200

Sign 174, 175, 176

Sign 206, 207, 208

Sign 188, 189

Sign 209

Sign 199

Sign 187

Sign 179, 183

Sign 192, 193 Mounting Surface

10.00"

A Painted, 1/2” Flat Cut Aluminum Font: Helvetica LT Std Bold Condensed CO104 White

Copy

A

Technical College

Date:

03.16.23

Revisions:

07.11.23 JA

08.23.23 JA

10.04.23 JA

Drawn By:

JA

Filename:

FLO0040_210563_EXT_Rev3

Rendering 15 of 15

Scale:

1/2” = 1’-0”

Custom

Notes:

120V Electrical Service Required

Wall Construction Details Required

Verify Mounting Conditions

Site Survey Required

8.00"

Sign 180, 181, 182

Type 9 Illuminated Wall Cabinet Mechanically Fasten to Building Fascia Mounting Hardware to Suit Wall Construction

QTY: 3

61.00"

A Painted, Routed 8” Deep Fabricated Aluminum to match PMS 7405 C

Body

B 3/16” Transluscent Acrylic Backer w/ First Surface Applied Translucent Vinyl Graphic: Customer Supplied Artwork to match PMS 2768 C / PMS 7405 C / 7328 White

Logo

B

A

Type Description Details Qty

TY9 Type 9 - Branding 3

TY1 Type 1 - Campus Identification 1

TY1-1 Type 1.1 - Campus Identification

TY2 Type 2 - Street Identification

TY3 Type 3 - Primary Directional

TY4 Type 4 - Parking Identification

TY 5 Type 5 - Campus Map

Type 6 - Walk Identification 14

TY6

TY7

TY8

Type 7 - Secondary Directional

Type 8 - Building Identification (F/S)

TY8-1 Type 8.1 - Building Identification (W/M) 25

Subtotal: 119

Sign Count

FLO0040

NOT FOR CONSTRUCTION

Issued Date: 2023-06-09 https://app.signagent.com/sign_template/552710/edit/ https://app.signagent.com/sign_template/550821/edit/ https://app.signagent.com/sign_template/550822/edit/ https://app.signagent.com/sign_template/550824/edit/ https://app.signagent.com/sign_template/550825/edit/ https://app.signagent.com/sign_template/642878/edit/ https://app.signagent.com/sign_template/550826/edit/ https://app.signagent.com/sign_template/550828/edit/ https://app.signagent.com/sign_template/642877/edit/ https://app.signagent.com/sign_template/550829/edit/ https://app.signagent.com/sign_template/550832/edit/ https://app.signagent.com/sign_template/550834/edit/ https://app.signagent.com/sign_template/642874/edit/ https://app.signagent.com/sign_template/550835/edit/ cortney.sevor Typewritten Text cortney.sevor Typewritten Text cortney.sevor Typewritten Text cortney.sevor Typewritten Text

TY5

cortney.sevor Typewritten Text cortney.sevor Typewritten Text cortney.sevor Typewritten Text

<------ Darlington Highway 52 Florence ------>

Parking

Parking

Parking

SiMT Advanced

Manufacturing Center

SiMT Manufacturing and Business Incubator

DuB ard Bl vd.

Fountain

800 Bldg.

Grounds

ETV

Tower

ReadySC

Bldg.

Automotive/HVAC Center

Exterior Site Plan Florence-Darlington Technical College LEGEND Standard Glassbackers Side 2Side 1

81-EXT-TY1

82-EXT-TY1-1

83-EXT-TY1-1

84-EXT-TY1-1

85-EXT-TY2

86-EXT-TY287-EXT-TY2

88-EXT-TY2

89-EXT-TY2

90-EXT-TY2

91-EXT-TY2

92-EXT-TY2

93-EXT-TY2

94-EXT-TY2

96-EXT-TY3

97-EXT-TY3

98-EXT-TY3

99-EXT-TY3

100-EXT-TY3

101-EXT-TY3

102-EXT-TY3

103-EXT-TY3

104-EXT-TY3

106-EXT-TY3

107-EXT-TY3

108-EXT-TY3

110-EXT-TY4

111-EXT-TY4

112-EXT-TY4

113-EXT-TY4

114-EXT-TY3

115-EXT-TY4

116-EXT-TY4

117-EXT-TY4

118-EXT-TY4

119-EXT-TY4

120-EXT-TY4

121-EXT-TY3 122-EXT-TY4

123-EXT-TY4

124-EXT-TY4

125-EXT-TY4

126-EXT-TY4

127-EXT-TY4

128-EXT-TY4

129-EXT-TY4

130-EXT-TY4

131-EXT-TY4

132-EXT-TY4

133-EXT-TY4

134-EXT-TY4

135-EXT-TY5

136-EXT-TY5

137-EXT-TY5

138-EXT-TY5

143-EXT-TY5

144-EXT-TY6

145-EXT-TY6

146-EXT-TY6

147-EXT-TY6

148-EXT-TY6

149-EXT-TY6

150-EXT-TY6

151-EXT-TY6

152-EXT-TY6

153-EXT-TY6

154-EXT-TY6

155-EXT-TY6

156-EXT-TY6

157-EXT-TY6

158-EXT-TY7

159-EXT-TY7

160-EXT-TY7

161-EXT-TY7

162-EXT-TY7

163-EXT-TY7

164-EXT-TY7

165-EXT-TY7

166-EXT-TY7

167-EXT-TY7

168-EXT-TY8

169-EXT-TY7

170-EXT-TY8-1

171-EXT-TY8-1

172-EXT-TY8-1

173-EXT-TY8-1

174-EXT-TY8-1

175-EXT-TY8-1176-EXT-TY8-1

177-EXT-TY8

178-EXT-TY8

179-EXT-TY8-1

180-EXT-TY9

181-EXT-TY9

182-EXT-TY9

183-EXT-TY8-1

184-EXT-TY8-1

185-EXT-TY8-1

186-EXT-TY8-1

187-EXT-TY8-1

188-EXT-TY8-1

189-EXT-TY8-1

190-EXT-TY7

191-EXT-TY7

192-EXT-TY8-1

193-EXT-TY8-1

196-EXT-TY8-1

198-EXT-TY8-1

199-EXT-TY8-1

200-EXT-TY8-1

203-EXT-TY8

205-EXT-TY8

206-EXT-TY8-1

207-EXT-TY8-1

208-EXT-TY8-1

209-EXT-TY8-1

210-EXT-TY7

211-EXT-TY3

212-EXT-TY8

END OF SECTION 10 14 00