Project CL20077004 PID.rtf

*** LTC PID Packaging Consolidated Text *** PLEASE SEE GLOSSARY AT THE END OF THE DOCUMENT FOR FULL TEXT OF THE ITEM DESCRIPTION

AND PACKAGING REFERENCE NUMBERS CALLED OUT FOR EACH NSN.

NSN:010603674

BASE, CANNON. (SUPPORT).

REFERENCE NUMBER:RA001

REFERENCE NUMBER:RD001

REFERENCE NUMBER:RP001

REFERENCE NUMBER:RQ001

REFERENCE NUMBER:RQ002

REFERENCE NUMBER:RQ009

REFERENCE NUMBER:RQ011

REFERENCE NUMBER:RT001

REFERENCE NUMBER:ZD003

REFERENCE NUMBER:RQ032

REFERENCE NUMBER:RD002

REFERENCE NUMBER:CQ006

REFERENCE NUMBER:CS187

REFERENCE NUMBER:ES371

_______________EXCEPTION DATA___________________

DRAWING 31933160 NOTE 12:

USE NAVSEA(53711)DRAWING 6782397 ILO MIL-PRF-24712

QPL IS NOT APPLICABLE.

SQAP010603674: DELETE PARAGRAPHS 4.1 AND 4.2

______________END OF EXCEPTIONS_________________

THIS ITEM IS A "DEFENSE ARTICLE" AS DEFINED IN

AND SUBJECT TO THE INTERNATIONAL TRAFFIC IN ARMS

REGULATIONS (22 C.F.R. 120-30) AND THE ARMS

EXPORT CONTROL ACT (22 U.S.C.A. 2778-2799).

ANY MANUFACTURER OR EXPORTER OF DEFENSE ARTICLES

IS REQUIRED TO REGISTER WITH THE DIRECTORATE OF

DEFENSE TRADE CONTROLS (DDTC), DEPARTMENT OF

STATE. DOCUMENTARY EVIDENCE OF REGISTRATION MAY

BE REQUIRED PRIOR TO AWARD. ADDITIONAL EXPORT

RESTRICTIONS APPLY AS INDICATED HEREIN. FAILURE

TO SUBMIT DDTC REGISTRATION WHEN REQUESTED WILL

MAKE A QUOTE/OFFER INELIGIBLE FOR AWARD.

THE ITEM BEING PROCURED IS A CRITICAL GUN PART

ITEM WITH UNIQUE REQUIREMENTS.

CONTRACTOR FAT APPLIES.

AFTER RECEIPT OF QUOTES, OFFERORS MAY BE

CONTACTED TO PRICE THE FAT REQUIREMENT.

PRODUCT INSPECTION WILL BE CONDUCTED BY THE DCMA

QAR AT THE ACTUAL MANUFACTURER'S FACILITY

IDENTIFIED ON THIS CONTRACT. THE IDENTIFICATION

OF THE ACTUAL MANUFACTURER MUST BE SUBMITTED TO

THE CONTRACTING OFFICER FOR INCLUSION IN THE

AWARD. UPON AWARD, ANY CHANGES TO THE ABOVE MUST

BE APPROVED BY THE PCO VIA FORMAL CONTRACT

MODIFICATION.

PRODUCT VERIFICATION TESTING (PVT) IN ACCORDANCE

WITH PROCUREMENT NOTE E05, MAY BE INVOKED FOR THE

REFERENCED CONTRACT. IF INVOKED, PVT SAMPLES MUST BE

INSPECTED, PACKAGED AND MARKED AS REQUIRED IN THE

CONTRACT. ONE (1) SAMPLE MAY BE DESTROYED DURING

TESTING.

PRODUCT VERIFICATION TESTING, IF INVOKED<(>,<)>

WILL BE PERFORMED PRIOR TO ACCEPTANCE OF

EACH SHIPMENT. THE CONTRACTOR MUST PROVIDE

PVT SAMPLES FROM EACH (SUB)CONTRACTOR USED

IN THE PRODUCTION OF PARTS ON THIS CONTRACT.

FIVE (5) PVT SAMPLES, UNLESS OTHERWISE

SPECIFIED, WILL BE REQUIRED TO BE IDENTIFIED

TO THOSE (SUB)CONTRACTORS WHEN THEY ARE SENT

IN FOR TESTING.

CRITICAL APPLICATION ITEM

IAW BASIC DRAWING NR 10001 3193160

REVISION NR P DTD 02/10/2005

PART PIECE NUMBER: 3193160-2

IAW REFERENCE DRAWING NR 53711 6782397

REVISION NR B DTD 03/29/2005

PART PIECE NUMBER:

IAW REFERENCE QAP 16236 SQAP010603674

REVISION NR DTD 04/03/2017

PART PIECE NUMBER:

PREP FOR DELIVERY

LINE ITEM 00001 TYPE OF COVERAGE: DLA DIRECT, CONUS

PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999

QUP:001 PRES MTHD:10 CLNG/DRY:1 PRESV MAT:00

WRAP MAT:CA CUSH/DUNN MAT:XX CUSH/DUNN THKNESS:X

UNIT CONT:D3 OPI:O

INTRMDTE CONT:DO INTRMDTE CONT QTY:AAA

PACK CODE:U

MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-129.

SPECIAL MARKING CODE:00 -00 No special marking

PALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY 01, 2008

NSN:012748914

SUPPORT,TRANSMISSION MOUNT

REFERENCE NUMBER:RA001

REFERENCE NUMBER:RQ032

REFERENCE NUMBER:RD002

REFERENCE NUMBER:RQ001

REFERENCE NUMBER:RQ002

REFERENCE NUMBER:RQ009

REFERENCE NUMBER:RQ011

REFERENCE NUMBER:RP001

REFERENCE NUMBER:RT001

REFERENCE NUMBER:ZD080

REFERENCE NUMBER:CS147

REFERENCE NUMBER:CS187

REFERENCE NUMBER:CQ006

REFERENCE NUMBER:CQ015

REFERENCE NUMBER:CQ046

IAW BASIC DRAWING NR 19207 12358605

REVISION NR F DTD 11/06/1996

PART PIECE NUMBER: 12358605-2

IAW REFERENCE DRAWING NR 19207 11629620

REVISION NR W DTD 04/20/1996

PART PIECE NUMBER: INTERFACE CONTROL

IAW REFERENCE QAP 19207 12358605

REVISION NR A DTD 04/03/1995

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12298021

REVISION NR A DTD 11/26/1985

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12358605-2

REVISION NR DTD 12/04/2019

PART PIECE NUMBER:

PREP FOR DELIVERY

LINE ITEM 00004 TYPE OF COVERAGE: DLA DIRECT, CONUS

PKGING DATA-QUP:001

IF MATERIAL IS CONSIDERED HAZARDOUS IAW FED-STD-313,

PACKAGE IN ACCORDANCE WITH TQ REQUIREMENT IP025.

IF THE MATERIAL IS NOT CONSIDERED HAZARDOUS, IN ACCORDANCE WITH

FED-STD-313, THE MATERIAL SHALL BE COMMERCIALLY PACKAGED IN ACCORDANCE

WITH ASTM D3951.

NSN:014964445

SPROCKET WHEEL

REFERENCE NUMBER:ZD004

REFERENCE NUMBER:RD002

REFERENCE NUMBER:RP001

REFERENCE NUMBER:RA001

REFERENCE NUMBER:RQ001

REFERENCE NUMBER:RQ002

REFERENCE NUMBER:RQ009

REFERENCE NUMBER:RQ011

REFERENCE NUMBER:RQ016

CERTIFICATE OF CONFORMANCE REQUIRED

EXCEPTION TO DATA: DWG 12369003 REV G CALLED OUT ON THE TDPL HAS BEEN

SUPERSEEDED BY DWG 12369003 REV J.

REFERENCE NUMBER:CS150

REFERENCE NUMBER:CS187

REFERENCE NUMBER:ZD080

CRITICAL APPLICATION ITEM

IAW BASIC DRAWING NR 19207 12474840

REVISION NR DTD 11/05/2001

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12369003

REVISION NR H DTD 09/24/2018

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12474840

REVISION NR DTD 04/29/2020

PART PIECE NUMBER:

IAW REFERENCE QAP 19207 12474840

REVISION NR A DTD 08/04/2004

LINE ITEM 00005 TYPE OF COVERAGE: DLA DIRECT, CONUS

PKGING DATA-QUP:001

WILL BE PACKAGED IN ACCORDANCE WITH ASTM D3951.

NSN:015915504

LIFTER,ROAD WHEEL

REFERENCE NUMBER:ZD004

REFERENCE NUMBER:RQ032

REFERENCE NUMBER:RD002

REFERENCE NUMBER:RP001

REFERENCE NUMBER:RA001

REFERENCE NUMBER:RQ001

REFERENCE NUMBER:RQ011

REFERENCE NUMBER:CS187

REFERENCE NUMBER:RQ016

REFERENCE NUMBER:RQ002

REFERENCE NUMBER:CA070

CRITICAL APPLICATION ITEM

IAW BASIC DRAWING NR 19207 12496775

REVISION NR B DTD 07/07/2015

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12350824

REVISION NR R DTD 09/28/2017

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12496774

REVISION NR E DTD 08/16/2017

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 19207 12496775

REVISION NR DTD 08/21/2018

LINE ITEM 00006 TYPE OF COVERAGE: DLA DIRECT, CONUS

PKGING DATA-QUP:001

WILL BE PACKAGED IN ACCORDANCE WITH ASTM D3951.

GLOSSARY

PACKAGING TEXT

THE FOLLOWING PARAGRAPH APPLIES TO ALL PACKAGING CALLED OUT IN THIS DOCUMENT:

All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951.

Mark and label all packaging and packing in accordance with MIL-STD-129.

The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order.

ITEM DESCRIPTION TEXT

REFERENCE NUMBER RA001

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS

(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE

DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB

AT:

http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE

SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE

ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE

APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON

REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

REFERENCE NUMBER RD001

RD001: DEMILITARIZATION: SMALL ARMS WEAPONS AND PARTS AND ACCESSORIES

(CATEGORY I - MUNITIONS LIST ITEMS, CATEGORY I-DODM 4160.28-VOL.3)

REFERENCE NUMBER RP001

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

REFERENCE NUMBER RQ001

RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND

NON-MANUFACTURERS)

REFERENCE NUMBER RQ002

RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL

REQUEST FOR VARIANCE (DEVIATION OR WAIVER)

REFERENCE NUMBER RQ009

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

REFERENCE NUMBER RQ011

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

REFERENCE NUMBER RT001

RT001: MEASURING AND TEST EQUIPMENT

REFERENCE NUMBER ZD003

A metal casting process was identified as a means to manufacture this item. Tooling is required to produce a casting. For sourcing, tooling, materials or other information, please contact the appropriate assistance team: (Aviation, C&E Supply Chains) DSCR.AFCAT@dla.mil; (Land & Maritime Supply Chains) DSCC.cast.forge@dla.mil

REFERENCE NUMBER RQ032

RQ032: EXPORT CONTROL OF TECHNICAL DATA

This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.

The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at:

https://www.dla.mil/HQ/LogisticsOperations/EnhancedValidation/

To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data.

REFERENCE NUMBER RD002

RD002, COVERED DEFENSE INFORMATION APPLIES

REFERENCE NUMBER CQ006

"CONTRACTOR/MANUFACTURER IS REQUIRED TO

ESTABLISH AND MAINTAIN A CALIBRATION SYSTEM THAT

MEETS THE REQUIREMENTS OF ANSI/NCSL Z540-1-1994,

AMERICAN NATIONAL STANDARD FOR CALIBRATION -

CALIBRATION LABORATORIES AND MEASURING AND TEST

EQUIPMENT-GENERAL REQUIREMENTS, OR ISO 10012-1,

QUALITY ASSURANCE REQUIREMENTS FOR MEASURING

EQUIPMENT- PART 1, METROLOGICAL CONFIRMATION

SYSTEM FOR MEASURING EQUIPMENT."

REFERENCE NUMBER CS187

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE

USED NOR INCORPORATED IN ANY ITEMS TO BE

DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION

SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT

DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS.

SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR

APPROVAL UNLESS THEY ARE AUTHORIZED BY THE

SPECIFICATION REQUIREMENTS.

REFERENCE NUMBER ES371

The Government Procuring Activity has determined that Surplus is not Acceptable for this NSN.

(End of TQ Requirement)

REFERENCE NUMBER ZD080

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ

H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE

SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,

STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR

AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF

VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED

ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE

SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER

MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR

PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT

SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT

UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

REFERENCE NUMBER CS147

"THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH

MUST CONFORM TO SOURCE CONTROL DRAWING. BY

SUBMITTING AN OFFER, THE OFFEROR AGREES TO

PROVIDE SOURCE CONTROLLED COMPONENTS FROM

SOURCES APPROVED ON THE APPLICABLE SOURCE

CONTROL DRAWING."

REFERENCE NUMBER CQ015

"FINAL INSPECTION AND ACCEPTANCE OF THE ITEM

SHALL BE AT THE ACTUAL MANUFACTURING FACILITY.

TECHNICAL INSPECTION IS REQUIRED. THE

CONTRACTOR SHALL MAKE DRAWINGS AND TECHNICAL

INFORMATION AVAILABLE TO VERIFY THAT THE ITEM

MEETS ALL TECHNICAL REQUIREMENTS.

COUNT, KIND, AND CONDITION INSPECTIONS ARE

NOT ACCEPTABLE. THIS NOTE TAKES PRECEDENCE OVER

MASTER SOLICITATION PART ONE PROVISIONS, NOTE 6,

QUOTATIONS BY NON-MANUFACTURERS (APR 1984,

DCSC 52.217-9C01). FINAL INSPECTION OF

PACKAGING, IF REQUIRED, MAY BE CONDUCTED

ELSEWHERE."

REFERENCE NUMBER CQ046

PROCESS, PROCEDURES, AND/OR WORKMANSHIP

SPECIMENS REQUIRED BY MILITARY SPECIFICATION(S)

OR DRAWINGS APPLICABLE TO THIS CONTRACT WILL BE

APPROVED BY THE ACTIVITY RESPONSIBLE FOR THE

ADMINISTRATION OF THE CONTRACT. POST AWARD

PREPRODUCTION APPROVAL VERIFYING THE

REQUIREMENTS OF CITED SPECIFICATION(S) IS

REQUIRED.

REFERENCE NUMBER IP025

IP025: PACKAGING, MARKING, AND SHIPPING OF HAZARDOUS MATERIALS

REFERENCE NUMBER ZD004

A forging process was identified as a means to manufacture this item.

Tooling is required to produce a forging. For sourcing, tooling, materials or other information, please contact the appropriate assistance team: (Aviation, C&E Supply Chains) DSCR.AFCAT@dla.mil;(Land & Maritime Supply Chains) DSCC.cast.forge@dla.mil

REFERENCE NUMBER RQ016

RQ016: COMPONENT QUALIFIED PRODUCTS LISTS (QPL)/QUALIFIED MANUFACTURERS

LISTS (QML). THIS ITEM CONTAINS ONE OR MORE COMPONENTS DEFINED BY A

SPECIFICATION(S) WITH AN ASSOCIATED QUALIFIED PRODUCTS LIST (QPL) OR

QUALIFIED MANUFACTURERS LIST (QML). QUALIFICATION REQUIREMENTS IN

PROCUREMENT NOTE H02 "COMPONENT QUALIFIED PRODUCTS LIST (QPL)/QUALIFIED

MANUFACTURERS LIST (QML)" APPLY.

REFERENCE NUMBER CS150

THIS NSN SHALL BE PHYSICALLY IDENTIFIED

I/A/W MIL-STD-130.

REFERENCE NUMBER CA070

FULL AND OPEN COMPETITION APPLY