Plow Truck_Salient Features.pdf

www.greatlakes-seaway.com

September 18, 2020

Procurement Request: 2021 Conventional Truck with Tenco Plow Package – Or Equal-

Truck Salient Features:

• Vehicle Configuration (or Equal):

o 1085D CONVENTIONAL CHASSIS o 2021 MODEL YEAR SPECIFIED o SET BACK AXLE -TRUCK o STRAIGHT TRUCK PROVISION o LH PRIMARY STEERING LOCATION

• General Service (or Equal):

o TRUCK CONFIGURATION o DOMICILED, USA (EXCLUDING CALIFORNIA AND CARB OPT-IN

STATES)

o CONSTRUCTION SERVICE o CONSTRUCTION BUSINESS SEGMENT o DRY BULK COMMODITY o TERRAIN/DUTY: 100% (ALL) OF THE TIME, IN TRANSIT, IS SPENT ON

PAVED ROADS

o MAXIMUM 8% EXPECTED GRADE o SMOOTH CONCRETE OR ASPHALT PAVEMENT· MOST SEVERE IN-

TRANSIT (BETWEEN SITES) ROAD SURFACE

o FREIGHTLINER SD VOCATIONAL WARRANTY EXPECTED FRONT

AXLE(S) LOAD: 16000.0 lbs o EXPECTED REAR DRIVE AXLE(S) LOAD: 26000.0 lbs o EXPECTED GROSS VEHICLE WEIGHT CAPACITY: 42000.0 lbs

• Truck Service (or Equal):

o FLATBED/PLATFORM/STAKE BODY ABC SUPPLY CO., INC

• Engine (or Equal):

o CUM L9 330 HP @ 2000 RPM, 2200 GOV RPM, 1000 LB/FT @ 1400 RPM

180 Andrews Street Massena, N.Y. 13662 Tel.: (315) 764-3200

• Electronic Parameters (or Equal):

o 75 MPH ROAD SPEED LIMIT o CRUISE CONTROL SPEED LIMIT SAME AS ROAD SPEED LIMIT o PTO MODE BRAKE OVERRIDE • SERVICE BRAKE APPLIED o PTO RPM WITH CRUISE SET SWITCH • 700 RPM o PTO RPM WITH CRUISE RESUME SWITCH· 800 RPM o PTO MODE CANCEL VEHICLE SPEED - 5 MPH o PTO GOVERNOR RAMP RATE. 250 RPM PER SECOND o PTO MINIMUM RPM • 700 o REGEN INHIBIT SPEED THRESHOLD • 5 MPH

• Engine Equipment (or Equal):

o 2016-2019 ONBOARD DIAGNOSTICS/2010 EPAJCARB/FINAL GHG17

CONFIGURATION

o NO 2008 CARB EMISSION CERTIFICATION o STANDARD OIL PAN o OIL FILL ANO DIPSTICK LOCATED FOR ENHANCED SERVICEABILITY o SIDE OF HOOD AIR INTAKE WITH FIREWALL MOUNTED DONALDSON

AIR CLEANER

o DR 12V 160 AMP 28-SI QUAORAMOUNT PAD ALTERNATOR WITH

REMOTE BATTERY VOLT SENSE

o (2) DTNA GENUINE, FLOODED STARTING, MIN 2000CCA, 370RC, THREADED STUD BATTERIES o BATTERY BOX FRAME MOUNTED o STANDARD BATTERY JUMPERS o SINGLE BATTERY BOX FRAME MOUNTED LH SIDE BACK OF CAB o WIRE GROUND RETURN FOR BATTERY CABLES WITH ADDITIONAL

FRAME GROUND RETURN

o NON-POLISHED BATTERY BOX COVER o CAB AUXILIARY POWER CABLE o POSITIVE LOAD DISCONNECT WITH CAB MOUNTED CONTROL

SWITCH MOUNTED OUTBOARD DRIVER SEAT

o CUMMINS TURBOCHARGED 16.7 CFM AIR COMPRESSOR WITH

INTERNAL SAFETY VALVE

o ELECTRONIC ENGINE INTEGRAL SHUTDOWN PROTECTION SYSTEM o CUMMINS ENGINE INTEGRAL BRAKE WITH VARIABLE GEOMETRY

TURBO ON/OFF

o RH OUTBOARD UNDER STEP MOUNTED HORIZONTAL

AFTERTREATMENT SYSTEM ASSEMBLY WITH RH B-PILLAR

MOUNTED VERTICAL TAILPIPE

o ENGINE AFTERTREATMENT DEVICE, AUTOMATIC OVER THE ROAD

REGENERATION AND DASH MOUNTED REGENERATION REQUEST

SWITCH

o 11 FOOT 06 INCH (138 INCH+0/-5.9 INCH) EXHAUST SYSTEM HEIGHT o RH CURVED VERTICAL TAILPIPE B-PILLAR MOUNTED ROUTED FROM

STEP

o 13 GALLON DIESEL EXHAUST FLUID TANK

• Engine Equipment (or Equal):

o 100 PERCENT DIESEL EXHAUST FLUID FILL o STANDARD DIESEL EXHAUST FLUID PUMP MOUNTING o NON-POLISHED ALUMINUM DIAMOND PLATE DIESEL EXHAUST

FLUID TANK COVER

o LH MEDIUM DUTY STANDARD DIESEL EXHAUST FLUID TANK

LOCATlON o STANDARD DIESEL EXHAUST FLUID TANK CAP o ALUMINUM AFTERTREATMENT DEVICE/MUFFLER/TAILPIPE

SHIELD(S)

o HORTON DRIVEMASTER ADVANTAGE ON/OFF FAN DRIVE o AUTOMATIC FAN CONTROL WITHOUT DASH SWITCH, NON ENGINE

MOUNTED

o CUMMINS SPIN ON FUEL FILTER o COMBINATION FULL FLOW/BYPASS OIL FILTER o 1115 SQUARE INCH ALUMINUM RADIATOR o ANTIFREEZE TO-34F, OAT (NITRITE AND SILICATE FREE) EXTENDED

LIFE COOLANT

o GATES BLUE STRIPE COOLANT HOSES OR EQUIVALENT o CONSTANT TENSION HOSE CLAMPS FOR COOLANT HOSES o RADIATOR DRAIN VALVE o 350 ADAPTER FLANGE FOR FRONT PTO PROVISION o PHILLIPS-TEMRO 150WATT/115 VOL TOIL PREHEATER o BLACK PLASTIC ENGINE HEATER RECEPTACLE MOUNTED UNDER LH

DOOR

o ELECTRIC GRID AIR INTAKE WARMER o DELCO 12V 38MT HO STARTER WITH INTEGRATED MAGNETIC

SWITCH

• Transmission (or Equal):

o ALLISON 3000 RDS AUTOMATIC TRANSMISSlON WITH PTO

PROVISION

• Transmission Equipment (or Equal):

o ALLISON VOCATIONAL PACKAGE 223 • AVAILABLE ON 3000/4000

PROOUCT FAMILIES WITH VOCATIONAL MODELS RDS, HS. MH AND

o TRV o ALLISON VOCATIONAL RATING FOR CONCRETE MIXER

APPLICATIONS ONLY AVAILABLE WITH 3000 PRODUCT FAMILIES

o PRIMARY MODE GEARS, LOWEST GEAR 1, START GEAR 1, HIGHEST

GEAR 6, AVAILABLE FOR 3000/4000 PRODUCT FAMILIES ONLY

o SECONDARY MODE GEARS, LOWEST GEAR 1, START GEAR 1, HIGHEST GEAR 6, AVAILABLE FOR 3000/4000 PRODUCT FAMILIES

ONLY

o PRIMARY SHIFT SCHEDULE RECOMMENDED BY DTNA AND

ALLISON, THIS DEFINED BY ENGINE AND VOCATIONAL USAGE

• Transmission Equipment (or Equal):

o SECONDARY SHIFT SCHEDULE RECOMMENDED BY DTNA AND

ALLISON, THIS DEFINED BY ENGINE AND VOCATIONAL USAGE

o PRIMARY SHIFT SPEED RECOMMENDED BY DTNA AND ALLISON, THIS DEFINED BY ENGINE AND VOCATIONAL USAGE o SECONDARY SHIFT SPEED RECOMMENDED BY DTNA AND ALLISON, THIS DEFINED BY ENGINE AND VOCATIONAL USAGE o FUEL SENSE 2.0 DISABLED· PERFORMANCE - TABLE BASED o DRIVER SWITCH INPUT - DEFAULT - NO SWITCHES o DIRECTION CHANGE ENABLED WITH MULTIPLEXED SERVICE

BRAKES - ALLISON 5TH GEN TRANSMISSIONS

o MAGNETIC PLUGS, ENGINE DRAIN, TRANSMISSION DRAIN, AXLE(S)

FILL AND DRAIN

o PUSH BUTTON ELECTRONIC SHIFT CONTROL, DASH MOUNTED o TRANSMISSION PROGNOSTICS - ENABLED 2013 o WATER TO OIL TRANSMISSION COOLER, IN RADIATOR END TANK o TRANSMISSION OIL CHECK AND FILL WITH ELECTRONIC OIL LEVEL

CHECK

o SYNTHETIC TRANSMISSION FLUID (TES-295 COMPLIANT)

• Front Axle and Equipment (or Equal):

o DETROIT DA-F-16.0..5 16,000# FL 1 71.0 KPl/3.74 DROP SINGLE FRONT

AXLE

o MERITOR 16.5X6 Q+ CAST SPIDER HEAVY DUTY CAM FRONT

BRAKES, DOUBLE ANCHOR, FABRICATED SHOES

o NON-ASBESTOS FRONT BRAKE LINING o CAST IRON OUTBOARD FRONT BRAKE DRUMS o FRONT BRAKE DUST SHIELDS o FRONT OIL SEALS o VENTED FRONT HUB CAPS WITH WINDOW, CENTER AND SIDE PLUGS

- OIL

o STANDARD SPINDLE NUTS FOR ALL AXLES o MERITOR AUTOMATIC FRONT SLACK ADJUSTERS o STANDARD KING PIN BUSHINGS o TRW TAS-85 POWER STEERING o POWER STEERING PUMP o 2 QUART SEE THROUGH POWER STEERING RESERVOIR o MINERAL SAE 80/90 FRONT AXLE LUBE

• Front Suspension (or Equal):

o 16,000# FLAT LEAF FRONT SUSPENSION o GRAPHITE BRONZE BUSHINGS WITH SEALS - FRONT SUSPENSION o NO FRONT SUSPENSION OPTIONS o NO FRONT SHOCK ABSORBERS

• Rear Axle and Equipment (or Equal):

o RS-26-185 26,000# T-SERJES SINGLE REAR AXLE o 4.30 REAR AXLE RATIO o IRON REAR AXLE CARRIER WITH STANDARD AXLE HOUSING o MXL 17T MERITOR EXTENDED LUBE MAlN DRIVELINE WITH HALF

ROUND YOKES

o DRlVER CONTROLLED TRACTION DIFFERENTIAL • SINGLE REAR

AXLE

o (1) DRIVER CONTROLLED DIFFERENTIAL LOCK REAR VALVE FOR

SINGLE DRIVE AXLE

o BLINKING LAMP WITH EACH MODE SWITCH, DIFFERENTIAL UNLOCK

WITH IGNITION OFF, ACTIVE <5 MPH

o MERITOR 16.5X7 P CAST SPIDER CAM REAR BRAKES, DOUBLE

ANCHOR, CAST SHOES

o NON-ASBESTOS REAR BRAKE LINING o BRAKE CAMS AND CHAMBERS ON REAR SIDE OF DRIVE AXLE(S) o WEBB HEAVY WEIGHT CAST IRON REAR BRAKE DRUMS o REAR OIL SEALS o WABCO TRISTOP D LONGSTROKE 1-DRIVE AXLE SPRING PARKING

CHAMBERS

o HALDEX AUTOMATIC REAR SLACK ADJUSTERS o CURRENT AVAILABLE SYNTHETIC 75W-90 REAR AXLE LUBE o STANDARD REAR AXLE BREATHER(S)

• Rear Suspension (or Equal) o 26,000# FLAT LEAF SPRING REAR SUSPENSION WITH HELPER AND

RADIUS ROD

o SPRING SUSPENSION - NO AXLE SPACERS STANDARD AXLE SEATS IN

AXLE CLAMP GROUP

o FORE/AFT CONTROL RODS

• Brake System (or Equal):

o WABCO 4S/4M ABS o REINFORCED NYLON, FABRIC BRAID AND WIRE BRAID CHASSIS AIR

LINES

o FIBER BRAID PARKING BRAKE HOSE o STANDARD BRAKE SYSTEM VALVES o STANDARD AIR SYSTEM PRESSURE PROTECTION SYSTEM o STD U.S. FRONT BRAKE VALVE o RELAY VALVE WITH 5-8 PSI CRACK PRESSURE, NO REAR

PROPORTIONING VALVE

o BW AD-9 BRAKE LINE AIR DRYER WITH HEATER o AIR DRYER FRAME MOUNTED o STEEL AIR BRAKE RESERVOIRS o PULL CABLE ON WET TANK, PETCOCK DRAIN VALVES ON ALL

OTHER AIR TANKS

• Trailer Connectors (or Equal):

o UPGRADED CHASSIS MULTIPLEXING UNIT

• Wheelbase & Frame (or Equal):

o 4325MM (170 INCH) WHEELBASE o 11/32X3-1/2X10-15/16 INCH STEEL FRAME

(8.73MMX277.8MM/0.344X10.94 INCH} 120KSI

o 1600MM (63 INCH) REAR FRAME OVERHANG o FRAME OVERHANG RANGE: 61 INCH TO 70 INCH o 24 INCH INTEGRAL FRONT FRAME EXTENSION o CALC'D BACK OF CAB TO REAR SUSP CJL (CA) 104.72 in o CALCULATED EFFECTIVE BACK OF CAB TO REAR SUSPENSION C/L

(CA): 101.72 in o CALC'D FRAME LENGTH - OVERALL : 298.42 o CALCULATED FRAME SPACE LH SIDE : 40.96 In o CALCULATED FRAME SPACE RH SIDE: 175.06 in o CALC'D SPACE AVAILABLE FOR DECKPLATE: 104.45 in o SQUARE END OF FRAME o REAR TOW HOOKS o FRONT CLOSING CROSSMEMBER o LIGHTWEIGHT HEAVY DUTY ALUMINUM ENGINE CROSSMEMBER o STANDARD MIDSHIP #1 CROSSMEMBER(S) o STANDARD REARMOST CROSSMEMBER o STANDARD SUSPENSION CROSSMEMBER

• Chassis Equipment (or Equal):

o 14 INCH PAINTED STEEL BUMPER o FRONT TOW HOOKS - FRAME MOUNTED o BUMPER MOUNTING FOR SINGLE LICENSE PLATE o GRADE 8 THREADED HEX HEADED FRAME FASTENERS

• Fuel Tanks (or Equal):

o 60 GALLON/227 LITER ALUMINUM FUEL TANK • LH o 25 INCH DIAMETER FUEL TANK(S) o PLAIN ALUMINUM/PAINTED STEEL FUEL/HYDRAULIC TANK(S) WITH

PAINTED BANDS

o FUEL TANK(S) FORWARD o PLAIN STEP FINISH o FUEL TANK CAP(S) o DETROIT FUELWATER SEPARATOR WITH WATER IN FUEL SENSOR o EQUIFLO INBOARD FUEL SYSTEM o HIGH TEMPERATURE REINFORCED NYLON FUEL LINE\

• Tires (or Equal):

o CONTINENTAL HAU 3 WT 315/80R22.5 20 PLY RADIAL FRONT TIRES o CONTINENTAL HDR2 11R22.5 14 PLY RADIAL REAR TIRES

• Hubs (or Equal):

o CONMET PRESET PLUS PREMIUM IRON FRONT HUBS o CONMET PRESET PLUS PREMIUM IRON REAR HUBS

• Wheels (or Equal):

o ACCURIDE 29039 22.5X9.00 10-HUB PILOT 5.25 INSET 5-HAND STEEL

DISC FRONT WHEELS

o ACCURIDE 28828 22.5X82510-HUB PILOT 2- HAND HD STEEL DISC

REAR WHEELS

• Cab Exterior (or Equal):

o 108 INCH BBC FLAT ROOF ALUMINUM CONVENTIONAL CAB o AIR CAB MOUNTlNG o NONREMOVABLE BUGSCREEN MOUNTED BEHIND GRILLE o FRONT FENDERS SET-BACK AXLE o LH AND RH GRAB HANDLES o STATIONARY BLACK GRlLLE o BLACK HOOD MOUNTED AIR INTAKE GRILLE o FIBERGLASS HOOD WITH ACCESS HATCHES o SINGLE 14 INCH ROUND POLISHED AIR HORN ROOF MOUNTED o SINGLE ELECTRIC HORN o SINGLE HORN SHIELD o DOOR LOCKS AND IGNITION SWITCH KEYED THE SAME o KEY QUANTITY OF 2 o REAR LICENSE PLATE MOUNT END OF FRAME o HALOGEN COMPOSITE HEADLAMPS WITH BLACK BEZELS o (5) AMBER MARKER LIGHTS o INTEGRAL STOP/TAIUBACKUP LIGHTS o STANDARD FRONT TURN SIGNAL LAMPS o DUAL WEST COAST BRIGHT FINISH HEATED MIRRORS WITH LH AND

RH REMOTE

o DOOR MOUNTED MIRRORS o 102 INCH EQUIPMENT WIDTH o LH AND RH 8 INCH BRIGHT FINISH CONVEX MIRRORS MOUNTED

UNDER PRIMARY MIRRORS

o RH AND LH 8 INCH HEATED STAINLESS STEEL FENDER MOUNTED

CONVEX MIRRORS WITH TRIPOD BRACKETS

o STANDARD SIDE/REAR REFLECTORS o RH AFTERTREATMENT SYSTEM CAB ACCESS WITH POLISHED

DIAMOND PLATE COVER

o 63X14 INCH TINTED REAR WINDOW o TINTED DOOR GLASS LH AND RH WITH TINTED OPERATING WING

WINDOWS

o RH AND LH ELECTRIC POWERED WINDOWS, PASSENGER SWITCHES

ON D(X}R(S)

o 1-PIECE SOLAR GREEN GLASS WINDSHIELD o 8 LITER (2 GAL) WINDSHIELD WASHER RESERVOIR, CAB MOUNTED.

WITHOUT FLUID LEVEL INDICATOR

• Cab Interior (or Equal):

o OPAL GRAY VINYL INTERIOR o MOLDED PLASTIC DOOR PANEL o MOLDED PLASTIC DOOR PANEL o BLACK MATS WITH SINGLE INSULATION o DASH MOUNTED ASH TRAY(S) WITHOUT LIGHTER o FORWARD ROOF MOUNTED CONSOLE WITH UPPER STORAGE

COMPARTMENTS WITHOUT NETTING

o IN DASH STORAGE BIN o (2) CUP HOLDERS LH AND RH DASH o GRAY/CHARCOAL FLAT DASH o HEATER. DEFROSTER AND AIR CONDITIONER o STANDARD HVAC DUCTING o MAIN HVAC CONTROLS WITH RECIRCULATION SWITCH o STANDARD HEATER PLUMBING o VALEO HEAVY DUTY A/C REFRIGERANT COMPRESSOR o BINARY CONTROL, R-134A o STANDARD INSULATION o SOLID-STATE CIRCUIT PROTECTION AND FUSES o 12V NEGATIVE GROUND ELECTRICAL SYSTEM o DOME LIGHT WITH 3-WAY SWITCH ACTIVATED BY LH AND RH

DOORS

o LH AND RH ELECTRIC DOOR LOCKS o (1) 12 VOLT POWER SUPPLY IN DASH o BASIC HIGH BACK AIR SUSPENSION DRIVER SEAT WITH

MECHANICAL LUMBAR AND INTEGRATED CUSHION EXTENSION

o BASIC HIGH BACK NON SUSPENSION PASSENGER SEAT o DUAL DRIVER SEAT ARMRESTS AND INBOARD PASSENGER SEAT

ARMREST

o LH AND RH INTEGRAL DOOR PANEL ARMRESTS o VINYL WITH VINYL INSERT DRIVER SEAT VINYL WITH VINYL

INSERT PASSENGER SEAT BLACK SEAT BEL TS

o FIXED STEERING COLUMN o 4-SPOKE 18 INCH (450MM) STEERING WHEEL o DRIVER AND PASSENGER INTERIOR SUN VISORS

• Instruments and Controls (or Equal):

o GRAY DRIVER INSTRUMENT PANEL o GRAY CENTER INSTRUMENT PANEL o BLACK GAUGE BEZELS o LOW AIR PRESSURE INDICATOR LIGHT AND AUDIBLE ALARM o 2 INCH PRIMARY AND SECONDARY AIR PRESSURE GAUGES o INTAKE MOUNTED AIR RESTRICTION INDICATOR WITHOUT

GRADUATIONS

o ELECTRONIC CRUISE CONTROL WITH SWITCHES IN LH SWITCH

PANEL

o KEY OPERATED IGNITION SWITCH AND INTEGRAL START POSITION;

4 POSITION OFF/RUNISTART/ACCESSORY

• Instruments and Controls (or Equal):

o ICU3S, 132X48 DISPLAY WITH DIAGNOSTICS, 28 LED WARNING

LAMPS AND DATA LINKED

o HEAVY DUTY ONBOARD DIAGNOSTICS INTERFACE CONNECTOR

LOCATED BELOW LH DASH

o 2 INCH ELECTRIC FUEL GAUGE o PROGRAMMABLE RPM CONTROL - ELECTRONIC ENGINE o ELECTRICAL ENGINE COOLANT TEMPERATURE GAUGE o 2 INCH TRANSMISSION OIL TEMPERATURE GAUGE o ENGINE AND TRIP HOUR METERS INTEGRAL WITHIN DRIVER

DISPLAY

o ELECTRIC ENGINE OIL PRESSURE GAUGE o AM/FM/WB WORLD TUNER RADIO WITH AUXILIARY INPUT, J1939 o DASH MOUNTED RADIO o (2) RADIO SPEAKERS IN CAB o AM/FM ANTENNA MOUNTED ON FORWARD LH ROOF o ELECTRONIC MPH SPEEDOMETER WITH SECONDARY KPH SCALE, WITHOUT ODOMETER o STANDARD VEHICLE SPEED SENSOR o ELECTRONIC 3000 RPM TACHOMETER o IGNITION SWITCH CONTROLLED ENGINE STOP o (6) IGN CONTROLLED EXTRA SWITCHES WITH IND LIGHTS WIRED TO

POWER DIST BOX WITH RELAYS PROVIDING 20 AMPS PER CIRCUIT

TO JUNCTION BLOCK AND 1 CIRCUIT AT 30 AMPS

o DIGITAL VOLTAGE DISPLAY INTEGRAL WITH DRIVER DISPLAY o SINGLE ELECTRIC WINDSHIELD WIPER MOTOR WITH DELAY o MARKER LIGHT SWITCH INTEGRAL WITH HEADLIGHT SWITCH o ONE VALVE PARKING BRAKE SYSTEM WITH WARNING INDICATOR o SELF CANCELING TURN SIGNAL SWITCH WITH DIMMER.

WASHER/WIPER AND HAZARD IN HANDLE

o INTEGRAL ELECTRONIC TURN SIGNAL FLASHER WITH HAZARD

LAMPS OVERRIDING STOP LAMPS

• Design (or Equal):

o PAINT: ONE SOLID COLOR

• Color (or Equal):

o CAB COLOR A L0006EY WHITE ELITE EY o BLACK, HIGH SOLIDS POLYURETHANE CHASSIS PAINT o POWDER WHITE (N0006EA) FRONT WHEELS/RIMS (PKWHT21, TKWHT21, W, TW) o POWDER WHITE (N0006EA) REAR WHEELS/RIMS (PKWHT2·1, TKWHT21, W, TW) o STANDARD BLACK BUMPER PAINT o STANDARD E COAT/UNDERCOATING

• Certification/Compliance (or Equal):

o U.S. FMVSS CERTIFICATION, EXCEPT SALES CABS AND GLIDER KITS

• Raw Performance (or Equal):

o CALCULATED EFFECTIVE BACK OF CAB TO REAR SUSPENSION C/L

(CA). 101.72 111

o CALC'D SPACE AVAILABLE FOR DECKPLATE · 104.45 in

HYDRAULICS TO INCLUDE (or Equal):

o Front mounted tandem pump with electric clutch for disengagement, powered by engine through a 1200 series driveline o Commercial 6-section valve body to be mounted behind cab in a steel enclosure, right side o All valves and controls are to be air actuated, Apsco controls o 40 Gallon reservoir with 1 1/4" shut off valves mounted behind cab, left side o Low oil level sensor with automatic shutdown and override control o 2FFL-12 dual knob sander control o Hard pipe to rear of body shall be stainless steel with short hoses as required o Hydraulic lines to front hitch and pump shall be stainless steel with short hoses as required o Quick couplers for all detachable equipment o Plow controls to be mounted on swinging pedestal per request o All valves, oils, and controls for the complete operations of dump body, plow equipment, and sander

Chassis must be delivered in a manner which allows the above listed equipment to be installed without modification to the chassis.