Nephi Salient Characteristics.pdf

Nephi Armory Equipment Salient Characteristics

Equipment must fit in a fitness room with the measurement of:

24’ 2 ¾” x 34’ 10”

Equipment

Custom Weight and Storage Rig

- 100% made in the USA

- Height Range 101"-102"

- Width Range 31’-32’

- Depth Range 24’-25’

- 3” X 3” tubing, 11 gauge uprights drilled through in 2 directions, spaced on 2” drilled 1 1/16” hole centers

- Base of rack is should be drilled with 1 1/16 holes on 2” centers for entire length with feet to raise base of rack. Base of rack should be raised 6” off floor for user safety and comfort.

- Anchor feet should be externally rotated at the end of each rack.

- Bar hooks (j-hooks) should be cut of plate steel with at least 1” thick plastic HDPE material.

- All bar hooks and pins should have safety, bull nosed machined ends supported and secured through both sides of all drilled uprights for maximum strength yield.

- There should be no metal to metal contact during placement of weightlifting bar in bar hooks due to solid, UHMU hook central core on each hook.

- All uprights need to accept storage, weight storage, stretch band, pull-up bar, and roller pads in any of 4 directions.

- For safety and durability, all assembly bolts of main frame should be secured by at least 1” diameter bolts that can be adjustable with common hand tools.

- Plate, chain, and band storage pattern need to be able to be adjusted or changed by customer to suit various needs to any position on the rack.

- Rack must be able to have a customizable laser cut wide rib arch support measuring 41-43” wide by 10” deep and 4” at arch throat top.

- Rack arch must include a custom laser cut logo made of steel and cut to order according to customer branding. Each individually laser cut layer will be ground down, free of defects, and electrostatically powder coated according to its branding designation.

- Front and rear brace of rack should be drilled on 2” centers for accessory attachments.

- Each hole on rack and accessories should be marked with a high machined, milled in highly visible number as to hole assignment index.

- Approximate 1 1/16” holes should be drilled on 2” centers along the entire length of overhead supports on the top, bottom, and all sides to facilitate stretch band anchor and storage pins.

- Rack needs to be band compatible in all 4 directions, overhead and 2 directions on rack base section.

- Base of rack should have top area protected from wear by a thick UHMU plastic wear guard.

- Rack needs to have ability to bolt both a Cable Colum and Lat Pull Down / Low Row Unit to rear or side uprights of Rack using existing pre-drilled holes.

- Rack should include over 17” long 1” diameter solid steel pins that are covered for storage and stretch band anchor points.

- All storage, dip, and locking internal pins should be welded on

- Removable, adjustable for position on rack revolving self-locking pull-up bars should have 1” solid steel rubber grip covered handles.

- Custom rig must include 1 x Lat Pull Low Row Machine Rack Attached Lat Pull / Low Row Machine 100% made in the USA Material minimum 11 Gauge Steel Minimum 1" Bolt Fasteners.

Minimum 300lb plate stack Must have minimum 12 Position Modular Knurled Foot Pegs Must have a premium upholstered, minimum 15.5” x 10.25” bicycle style seat Must have minimum 12.5” thigh roller pads with 7 height positions and accommodate athletes up to 7' tall.

Must have adjustable machined HDPE band attachment points for adding an additional resistance option to the weight stack.

Must have Nylon Coated Aircraft Cables with Cable Thickness of 5/32"-7/32" Must have machined aluminum pulleys.

Minimum 70,000 PSI full pass mig welds Minimum 3 mils TGIC Powder coat paint Main framing must be brushed steel with a clear grind coating

- Custom Rig must also Include 4 x Functional Cable Columns

Rack Attached Functional Cable Column (Single Handle) 100% made in the USA Material minimum 11 Gauge Steel Minimum 1" Bolt Fasteners Minimum 250lb plate stack Must Include single handles and carabiner Must have Single Handle Adjustable Attachment Point and adjust on chromed telespar tubing Pulleys must be made from chromed hardened steel and high quality plastic Must have free rolling, adjustable tension band pegs attachments points Must have cam-guided cables for proper biomechanical loading of the muscle.

Must have Nylon Coated Aircraft Cables with Cable Thickness of 5/32"-7/32" Minimum 70,000 PSI full pass mig welds Minimum 3 mils TGIC Powder coat paint Main framing must be brushed steel with a clear grind coating

-Custom Rig must have built in storage for a set of 5-100 Hex Head Dumbbells -Custom Rig must have storage for at least 9 Medicine balls -Custom Rig must have 2 x Pairs of Adjustable Jammer Arm Attachments

Power Rack Adjustable Jammer Arms Attachment 100% made in the USA The Jammer Arms should be made of 11 Gauge American Steel Should be at least 48” long, 3” width, 3” height and is made completely in the USA.

Adjustable Bracket should be 11.5"L x 10.5"W x14.5" with a 14.5" Handle Width

Adjustable Recon Bench

- 100% made in the USA

- Adjustable to 5 positions.

- Entire frame construction of 11-gauge and 7-gauge 2” square steel bent tubing and at least 70,000 PSI full-pass mig welds and rubber caps.

- Integral wheels of solid rubber, 2” diameter (minimum). Must not contact floor when in use.

- Handle at seat-end of bench for ease of transport.

- Gravity-activated angle support

- There should be no inserts or additional pads between back and seat pad.

- Bench height 17-19”.

- Pads should be made with at least 3/4” birch plywood backboard with all corners and edges rounded

- 1” thick (minimum) high-density, non-moisture absorbing, closed-cell rebound foam covered with fully-sewn uniroyal “Spirit 2” Naugahyde, mounted to frame.

- Back pad 11-12” wide x 43-45” long.

- Seat pad tapered from 10” (rear) to 6” (front) for comfort.

- Bench must have ability to be stored in upright position when not in use.

Rubber Bumper Plate Set

- Weights Included: 40x45lbs, 40x25lbs, 40x10lbs

- 100% made in the USA

- Plate Diameter 17.72”

- Durometer 85 +/- 5

- Weight Tolerance +/- 2%

- Material Crumb Rubber

- Fits Olympic and Specialty Barbells

- Warranty 1 year

Urethane Change Plate Set

- Weights Included: 40x5lb and 40x2.5lb

- Must be 12-Sided Anti Roll design

- Must be 100% USA Made

- Must have a 5-year Guarantee

- Must be Urethane encased steel plates

Performance Bar

- 100% made in the USA

- Must have a weight of 20kg

- Must have a diameter of 28.5mm

- Must have Olympic & Power Lifting Ring Knurl Marks

- No center knurl

- Must have a Bright Zinc Shaft Coating

- Minimum Tensile Strength of 190k PSI

- Must have Hardened Chrome Sleeve Coating

- Must have Bronze Bushings

Magnetic Collars (Pair)

- Height 3"

- 100% made in the USA

- Weight 1 LB

- Diameter 1.937" to 2.007"

- Thickness 1.75"

- Twist To Tighten mechanism

- Integrated Magnetic Storage

- Made of 6,6 nylon commercial grade material

D-Ball Medicine Balls

- Sizes – 9” – 10lb and 15lb / 10.6” – 25lb

- Textured rubber shell

- 100% made in the USA

- Must be durable enough for slams and traditional medicine ball training

- warranty for 2 years from the date of purchase

Ductile Iron Kettlebell Set

- Weights Included: 1x8kg, 1x12kg, 1x16kg, 1x24kg, 1x28kg, 1x32kg

- Made in the USA

- Minimum 60 KSI Tensile Strength

- Must be Made with grade 65-45-12 Ductile iron.

- Must be Magnesium treated before casting to prevent and resist cracking during dropping and high intensity training. Resulting product is more than three times stronger than standard gray class 30 cast iron.

- Must be Corrosion resistant, bends without cracking, nodular graphite infused, and powder coated for smooth finish.

- Must be banded and colored for easy weight recognition.

Landmine - Multi directional torso trainer

- Must lock into any location that has 4-Way hole design

- Must be Made of 3/8" Steel, Schedule 40 Seamless Pipe.

- Length Range 16-17"

- Width 2.5"

- Must have Universal Swivel Joint/ Must have Bronze Oil Lite Bushings.

Professional Installation -Professional set-up, tuning, and calibration of listed equipment -Inspection of straps, cables and structural integrity of the racks/rigs and equipment -Vendor not responsible for mounting any equipment to the wall or floor