DWG_NO__216B_-_CET_AREA.pdf

A SEE SHEET 2

BUILDING 1461

HIGH BAY CHAMBER ROOM

SHEETS 2&3 SHOW DETAILS OF

THE INSTALLATION AREA FOR

THE NEW COMBINED ENVIRONMENTAL

TEST (CET) CHAMBERS

FRONT LOBBY

AREA

NOTE: THESE DRAWINGS ARE FOR

REFERENCE ONLY. FINAL

DIMENSIONS AND LOCATION

OF COMPONENTS ARE THE

VENDOR'S RESPONSIBILITY.

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

THE UNITED STATES DEPARTMENT OF THE

NAVY. ANY REPRODUCTION IN PART OR

AS A WHOLE WITHOUT THE WRITTEN

PERMISSION OF UNITED STATES

DEPARTMENT OF THE NAVY IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

NEXT ASSEM USED ON

APPLICATION

DIMENSIONS ARE IN INCHES

TOLERANCES:

FRACTIONAL 1/16

DECIMAL (0.0): 0.1

DECIMAL (0.00): 0.03

DECIMAL (0.000): 0.010

ANGULAR: 1/2

INTERPRET GEOMETRIC

TOLERANCING PER: ASME 14.5.1M

MATERIAL

FINISH

N/A

DRAWN

CHECKED

ENG APPR.

DESIGN

Q.A.

PROPULSION

POWER

4.4

DATENAME

TITLE:

SIZE

B

DWG. NO. REV

WEIGHT: SCALE: 1:512

UNLESS OTHERWISE SPECIFIED:

RMR

WJ 10/22/2015

10/21/2015

COMBINED

ENVIROMENTAL

TEST FACILITY AREA

SHEET 1 OF 3

[216B] CET AREA SOW

DRAWING

DO NOT SCALE DRAWING

DEPARTMENT OF THE NAVY

NAVAL AIR WARFARE CENTER - AIRCRAFT DIVISION

PATUXENT RIVER, MARYLAND 20670

216B

8'-5.0" 10'-8.0"

4'-0.0"

12'-0.0" 4'-0.0"

3'-6.0"

25'-11.0"

25'-9.5"

DETAIL A

SCALE 1 : 100

12' x 12' ROLL UP DOOR/OUTSIDE ENTRANCE

8" DIA FIRE WATER MAIN HEADER

EXISTING 10" SHAKER EXHAUST DUCTS.

EXISTING OUTSIDE WALL PENETRATIONS

SHALL BE USED.

OVERHEAD BUS DUCT PLUG-IN

BREAKER. 480V, 4W, 350A

OVERHEAD BUS DUCT MAIN

FEEDER WITH SHUTTERS FOR

THE CHAMBER ROOM. 480 V,

4W, 4000 A

HATCHED AREA INSIDE THESE BOUNDARIES IS THE

AVAILABLE INSTALL AREA FOR THE CHAMBERS

AND CONTROLS

AUXILARY AREA AVAILABLE

FOR USE

FABRICATION ROOM WALL. 2.00" SHOP

AIR SUPPLY WILL ENTER THE INSTALL

AREA THRU THIS WALL IN THE MOST

APPROPRIATE LOCATION DETERMINED

BY THE FINAL POSITION OF THE NEW

CHAMBER EQUIPMENT SKIDS. THIS WILL

BE THE GOVERNMENT'S RESPONSIBILITY.

NOTE: THESE DRAWINGS ARE FOR

REFERENCE ONLY. FINAL

DIMENSIONS AND LOCATION

OF COMPONENTS ARE THE

VENDOR'S RESPONSIBILITY.

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

THE UNITED STATES DEPARTMENT OF THE

NAVY. ANY REPRODUCTION IN PART OR

AS A WHOLE WITHOUT THE WRITTEN

PERMISSION OF UNITED STATES

DEPARTMENT OF THE NAVY IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

NEXT ASSEM USED ON

APPLICATION

DIMENSIONS ARE IN INCHES

TOLERANCES:

FRACTIONAL 1/16

DECIMAL (0.0): 0.1

DECIMAL (0.00): 0.03

DECIMAL (0.000): 0.010

ANGULAR: 1/2

INTERPRET GEOMETRIC

TOLERANCING PER: ASME 14.5.1M

MATERIAL

FINISH

N/A

DRAWN

CHECKED

ENG APPR.

DESIGN

Q.A.

PROPULSION

POWER

4.4

DATENAME

TITLE:

SIZE

B

DWG. NO. REV

WEIGHT: SCALE: 1:512

UNLESS OTHERWISE SPECIFIED:

RMR

WJ 10/22/2015

10/21/2015

COMBINED

ENVIROMENTAL

TEST FACILITY AREA

SHEET 2 OF 3

[216B] CET AREA SOW

DRAWING

DO NOT SCALE DRAWING

DEPARTMENT OF THE NAVY

NAVAL AIR WARFARE CENTER - AIRCRAFT DIVISION

BB

VIBE LAB AND

CONTROL ROOM

WALK-IN-CHAMBER

SUPPORT EQUIPMENT

ROOM

FABRICATION ROOM

BUILDING 1461

EXISTING STORAGE

CABINETS

B

SECTION B-B

14'-0.0"

8'-5.0"

7'-0.0"

11'-3.5"

DETAIL B

SCALE 1 : 80

12' X 12'ROLL UP

DOOR TO REAR

PARKING LOT

OUTSIDE WALL

BUILDING FIRE SPRINKLER

MAIN HEADER

THRU THE WALL

EXHAUST FAN

THRU THE WALL

FRESH AIR

MAKE-UP

EXISTING WALL PENETRATIONS

FORSHAKER EXHAUSTS

STORAGE CABINET

FABRICATION ROOM

EXISTING PULL BOX

NOT FOR NEW

CHAMBER POWER

CONCRETE FLOOR

VIBE LAB WALL

ROOF BAR JOISTS SIT

SIT ON TOP OF THIS

WALL

EXISTING DISCONNECT FOR

FUTURE UNIT UNDER TEST POWER

REQUIREMENTS

CET CHAMBER AREA

NOTE: THERE ARE OTHER OBSTRUCTIONS WHICH HANG BELOW THE TOP OF THE 14'-00"

WALL. LAB SPACE LIGHTING FIXTURES, WATER PIPES, ETC. THERE IS CLEAR SPACE OF

12'-00" BELOW THESE OBSTRUCTIONS.

NOTE: THESE DRAWINGS ARE FOR

REFERENCE ONLY. FINAL

DIMENSIONS AND LOCATION

OF COMPONENTS ARE THE

VENDOR'S RESPONSIBILITY.

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

THE UNITED STATES DEPARTMENT OF THE

NAVY. ANY REPRODUCTION IN PART OR

AS A WHOLE WITHOUT THE WRITTEN

PERMISSION OF UNITED STATES

DEPARTMENT OF THE NAVY IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

NEXT ASSEM USED ON

APPLICATION

DIMENSIONS ARE IN INCHES

TOLERANCES:

FRACTIONAL 1/16

DECIMAL (0.0): 0.1

DECIMAL (0.00): 0.03

DECIMAL (0.000): 0.010

ANGULAR: 1/2

INTERPRET GEOMETRIC

TOLERANCING PER: ASME 14.5.1M

MATERIAL

FINISH

N/A

DRAWN

CHECKED

ENG APPR.

DESIGN

Q.A.

PROPULSION

POWER

4.4

DATENAME

TITLE:

SIZE

B

DWG. NO. REV

WEIGHT: SCALE: 1:512

UNLESS OTHERWISE SPECIFIED:

RMR

WJ 10/22/2015

10/21/2015

COMBINED

ENVIROMENTAL

TEST FACILITY AREA

SHEET 3 OF 3

[216B] CET AREA SOW

DRAWING

DO NOT SCALE DRAWING

DEPARTMENT OF THE NAVY

NAVAL AIR WARFARE CENTER - AIRCRAFT DIVISION