Amendment_3.pdf

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

Except as provided herein, all terms and conditions of the document referenced in Item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A. NAME AND TITLE OF SIGNER (Type or print)

30-105-04EXCEPTION TO SF 30

APPROVED BY OIRM 11-84

STANDARD FORM 30 (Rev. 10-83) Prescribed by GSA

FAR (48 CFR) 53.243

The purpose of this Amendment is to add the revised SOW, revise CLINS, and to extend the response date.

1. CONTRACT ID CODE PAGE OF PAGES

J 1 8

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)

16C. DATE SIGNED

BY 19-Sep-2018

16B. UNITED STATES OF AMERICA15C. DATE SIGNED15B. CONTRACTOR/OFFEROR

(Signature of Contracting Officer)(Signature of person authorized to sign)

8. NAME AND ADDRESS OF CONTRACTOR (No., Street, County, State and Zip Code) X N6426718T0205

X 9B. DATED (SEE ITEM 11)

10-Aug-2018

10B. DATED (SEE ITEM 13)

9A. AMENDMENT OF SOLICITATION NO.

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

X The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offer X is extended, is not extended.

Offer must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended by one of the following methods:

(a) By completing Items 8 and 15, and returning 1 copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted;

or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN

REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. ACCOUNTING AND APPROPRIATION DATA (If required)

13. THIS ITEM APPLIES ONLY TO MODIFICATIONS OF CONTRACTS/ORDERS.

IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE

CONTRACT ORDER NO. IN ITEM 10A.

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, appropriation date, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(B).

C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority)

E. IMPORTANT: Contractor is not, is required to sign this document and return copies to the issuing office.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

10A. MOD. OF CONTRACT/ORDER NO.

2. AMENDMENT/MODIFICATION NO. 5. PROJECT NO.(If applicable)

6. ISSUED BY

3. EFFECTIVE DATE

19-Sep-2018

CODE

NAVAL SURFACE WARFARE CENTER CORONA DIV.

1999 FOURTH STREET BLDG 510

NORCO CA 92860

N64267 7. ADMINISTERED BY (If other than item 6)

4. REQUISITION/PURCHASE REQ. NO.

CODE

See Item 6

FACILITY CODECODE

EMAIL:TEL:

N6426718T0205

SECTION SF 30 BLOCK 14 CONTINUATION PAGE

SUMMARY OF CHANGES

SECTION A - SOLICITATION/CONTRACT FORM

The required response date/time has changed from 18-Sep-2018 01:00 PM to 19-Sep-2018 05:00 PM.

SECTION B - SUPPLIES OR SERVICES AND PRICES

CLIN 0019

The CLIN description has changed from Powder Sieve to Item Removed/Deleted from SOW.

The pricing detail quantity has decreased by 1.00 from 1.00 to 0.00.

CLIN 0020

The CLIN description has changed from Additional Sieve to Item Removed/Deleted from SOW.

CLIN 0027

The CLIN description has changed from Building Chamber Reduction Kit to Item Removed/Deleted from

SOW.

CLIN 0028

The CLIN description has changed from Reduced Chamber Building Plate to Items Removed/Deleted from SOW.

CLIN 0029

The CLIN description has changed from Building Chamber Reduction Kit Installat to Item Removed/Deleted from SOW.

SECTION C - DESCRIPTIONS AND SPECIFICATIONS

The following have been modified:

GENERAL

This is a Request for Quotation (RFQ) for a commercial item(s) prepared in accordance with the information in FAR Parts 12 and 13.5.

SALES TAX EXEMPTION

The contractor is hereby advised that the United States Government and Agencies thereof are exempt from State and Local Government tax by virtue of Article 6 of the United States Constitution. No exemption certificate is required.

Statement of Work Measurement Science and Engineering Department, 3D Metal Printer

1. INTRODUCTION

The Naval Surface Warfare Center (NSWC), Corona Division, Measurement Science Department, Code MS21 requires the purchase of one (1) Metal Additive Manufacturing (AM) Powder Bed Fusion Machine used for the research of AM processes to certify critical parts as well as the repair and manufacturing of special interface gages, weapon systems prototypes, and support equipment.

2. BACKGROUND

A Capital Improvement Program (CIP) at NSWC Corona has been awarded to purchase a Metal Additive Manufacturing Machine. This machine will be used for both Research into certifying critical parts necessary for the Navy to use this technology for critical applications, as well as for general machining and cost and time savings for operations at NSWC Corona. This AM Machine will be placed in the Measurement Science & Technology Laboratory (MSTL) at NSWC Corona. This machine will also be used to repair and manufacture special interface gages, support equipment, and prototypes for mission critical weapon systems while reducing costs and increasing production efforts.

3. SCOPE

The scope of this proposal is the complete purchase installation of all equipment and materials necessary to operate a Metallic Powder Bed Fusion process within NSWC Corona.

4. APPLICABLE DOCUMENTS

Document Type No./Version Title Date

GSA

FED-STD-313 Hazardous Materials Management (HAZMAT) https://www.gsa.gov/cdnstatic/FED-STD-313E.pdf

Jul 2014

GOV

FAR 23.3 Material Safety Data Sheets (MSDS) https://www.acquisition.gov/?q=browsefar

Jan 2018

5. REQUIREMENTS

The following is a synopsis of the requirements requested by NSWC Corona for the integration of a Metallic Powder Bed Fusion machine at NSWC Corona.

Product Name Part Number Quantity Part Description General

M2Cusing DL 400W

1 Metal AM System with an ATEX explosive atmosphere certification, with a minimum build envelope of 250 mm x 250 mm x 350 mm (x,y,z) to operate reactive and non-reactive powder materials including Maraging Tool Steel, Stainless Tool Steel, Aluminum, Titanium, and Inconel. Dual industry standard continuous laser, glove box insert, movable process chamber, open architecture, access for sensor integration above build chamber, unlimited operator contact with metal powder, and unexposed material containers.

Approved for use of third party materials to use within the machine, active dual laser meltpool monitoring, expansive and cost effective customer support, FAA certified part support, part accuracy of ±.003 inches and surface finish of Ra 177 and 275 µin.

Max Envelope Machine

N/A Height:90” Width: 110” Depth:75”

Power Supply N/A Max Power Supply 3/N/PE AC 400V Materials 1 Software Capability for Maraging Tool Steel, 316 SS, GD-AlSi10Mg, TiAl6V4, and Inconel 625.

Non Traditional

Materials 1 Software Capability for Platinum and Tungsten

Powder 1 Minimum 250kg of Maraging Tool Steel, 316 SS, and GD-AlSi10Mg, 50 kg of Inconel 625, 50 kg of TiAl6V4

Laser Scanning Speed

N/A Minimum Scanning speed 7 m/s, 4.5 m/s for variable focus move

Layer Thickness N/A Maximum Layer thickness 80µm Production Speed N/A 2 - 20 cm3/h (depending on material / laser power)

Power Consumption N/A Maximum power consumption 9 kW Furnace Nabertherm

N41/H furnace

1 Furnace to provide heat-treatment and stress relief for parts in an inert gas atmosphere. Voltage of 400V. 50Hz. Minimum furnace dimensions, 350 mm x 500 mm. 250 mm. Minimum Volume of 41 liters. Should include gas box, manual gas fitting, charging plate, charging cart, temperature display, hardening foil, and hardening tongs, gloves.

Wet Separator Vacuum

Ruwac wet separator NA7

- 11 CL

1 Wet Separator Vacuum to remove excess powder from the build chamber and safely passivate the powder in the receiver tank filled with fluid. Minimum Air flow 130m3/h, Fluid Volume, 7 liters.

Laser Power Measurement

QM Power 1 Equipment used to measure, standardize and compare the laser power and various positions in the process chamber used to ensure uniform power distribution through the entire build platform

Clamping System EROWA clamping system

1 Palletizing system to finish traditionally prefabricated parts

Micro Bead System Peenmatic 620 S

Bead blasting system used for post processing part surfaces

Powder Exchange Container (Master)

Powder exchange container (Master)

9 Inert Filtration Exchange System, Minimum tumbler diameter of 400mm.

Powder Sieve 1 Powder sieve to filter powder Additional Sieve 1 Additional Sieve for a minimum of 60 micrometer sieving capability

Powder Container Shelf

Powder container shelfrack system

1 Storage for powder exchange containers. Minimum 500kg load bearing.

Nitrogen Generator

MIDIGAS2 1 For use of non-reactive materials such as maraging tool steel, a Nitrogen Generator shall provide a minimum inlet pressure of 6 bar

Wear Parts Wear Parts Kit

2 Minimum of 20 Steel, Plastic, and Rubber Recoater blades

Build Plates Aluminum

M2cusing 5 5 build plates in Aluminum

Build Plate Steel M2cusing 250x250

10 Steel build plates

Build Plate Titanium

M2cusing 250x250

5 Titanium build plates

External Sieve Station

QM Powder External sieve station with extra-large sieve area and small mesh size up to minimum of 45 μm under an inert gas atmosphere

Raster Software Materialise Magics Package M2 Cusing

1 Providing raster software Materialise to allowing industry adopted capability of developing Machine Laser Raster Path

Intuitive Programming

Intuitive Program System to guide operator through the steps of machine programming.

Training CLWRX parameter training

1 Provide Training for Standard usage of the machine including all safety procedures, troubleshooting, powder exchange and handling of reactive powders, and real time monitoring.

Installation Machine Installation

Installation of the machine into the government facility

Shipping DDP shipping

1 Machine and all additional equipment shipped to government facility

Pre Installation Site Visit

Pre Installation Site Visit

1 Site visit vendor for facility inspection for appropriate installation of Machine and supplemental equipment

Powder Lift INOX 200 1 Electrical Lifting device used to load and unload Powder chambers inside the machine

Basic Maintenance Agreement

Basic Maintenance Agreement M2cusing

1 Basic Maintenance Agreement

Training at Customer’s Site

Training at Customer's Site

1 Training at Customer's Site

Powder Coating Analysis Module

QM Coating

1 A module that monitors and analyses the applied powder layer during the building process. The module should take a picture before and after the application of a layer is taken for each powder layer and analyzed by the associated analysis software.

Laser Meltpool Monitoring Module

QM

Meltpool 3D

2 Real-time quality management system module to monitor the melting pool, integrated into the optical path. Tracking of the ongoing building process via two optical sensors per scanner unit with several thousands of pictures per second, correlating to the emission position at the construction site. Real-time analysis of relevant data of the melting path including documentation. 3D visualization of the melting pool data in the form of the part geometry.

Surge Protector

UPS

TLE Series

UPS

480V/277 in/out

1 A UPS that will provide surge protection for the PBF Machine. This should include a Battery Cabinet, 40kVA- 480VAC with static Bypass Wall Mount/ Maintenance Bypass Cabinet, and iUPS.

Item Unique

Identification Tag

(IUID)

IUID tag plate per MIL-STD-130x

SECTION F - DELIVERIES OR PERFORMANCE

The following Delivery Schedule item for CLIN 0019 has been changed from:

DELIVERY DATE QUANTITY SHIP TO ADDRESS DODAAC /

CAGE

90 dys. ADC 1 NAVAL SURFACE WARFARE CENTER

TBD.

1999 FOURTH ST BUILDING 204

NORCO CA 92860

951-393-4760 FOB: Destination

N64267

To:

DELIVERY DATE QUANTITY SHIP TO ADDRESS DODAAC /

CAGE

90 dys. ADC 0 NAVAL SURFACE WARFARE CENTER

TBD.

1999 FOURTH ST BUILDING 204

NORCO CA 92860

951-393-4760

The following Delivery Schedule item for CLIN 0020 has been changed from:

CAGE

30 dys. ADC 1 NAVAL SURFACE WARFARE CENTER

TBD.

1999 FOURTH ST BUILDING 204

NORCO CA 92860

951-393-4760

CAGE

30 dys. ADC 0 NAVAL SURFACE WARFARE CENTER

TBD.

1999 FOURTH ST BUILDING 204

NORCO CA 92860

951-393-4760

The following Delivery Schedule item for CLIN 0027 has been changed from:

CAGE

90 dys. ADC 1 NAVAL SURFACE WARFARE CENTER

TBD.

1999 FOURTH ST BUILDING 204

NORCO CA 92860

951-393-4760

CAGE

90 dys. ADC 0 NAVAL SURFACE WARFARE CENTER

TBD.

1999 FOURTH ST BUILDING 204

NORCO CA 92860

951-393-4760

The following Delivery Schedule item for CLIN 0028 has been changed from:

CAGE

90 dys. ADC 1 NAVAL SURFACE WARFARE CENTER

TBD.

1999 FOURTH ST BUILDING 204

NORCO CA 92860

951-393-4760

CAGE

90 dys. ADC 0 NAVAL SURFACE WARFARE CENTER

TBD.

1999 FOURTH ST BUILDING 204

NORCO CA 92860

951-393-4760

The following Delivery Schedule item for CLIN 0029 has been changed from:

CAGE

90 dys. ADC 1 NAVAL SURFACE WARFARE CENTER

TBD.

1999 FOURTH ST BUILDING 204

NORCO CA 92860

951-393-4760

CAGE

90 dys. ADC 0 NAVAL SURFACE WARFARE CENTER

TBD.

1999 FOURTH ST BUILDING 204

NORCO CA 92860

951-393-4760

(End of Summary of Changes)