IBM10B0006_specsIntroToTechSpecs_amend 5_attmt4.pdf

Upper Rio Grande Flood Control Project – Rectification Reaches Rehabilitation Improvements for Fort Hancock Reach and Fabens Reach Hudspeth County & El Paso County, Texas

IDENTIFICATION OF TECHNICAL SPECIFICATIONS

USIBWC Contract No.: IBM10BO006-Amendment 5 Page 01.01.00 - 1

SPECIFICATION 01 01 00

This specification provides for the identification and introduction to the technical specifications and related information, and includes the following:

1.1 Governing Technical Specifications

1.2 Related Documents & Provisions

1.3 Provisions for Measurement and Payment

1.4 Specification / Bid Item Format and Conventions

PART 1 - GENERAL

1.1 GOVERNING TECHNICAL SPECIFICATIONS

A. All technical specifications applicable to this Contract are identified as follows:

DIVISION 00 - PROCUREMENT AND CONTRACTING REQUIREMENTS

SPECIFICATION 00 01 01 PROJECT TITLE

SPECIFICATION 00 01 10 TABLE OF CONTENTS

SPECIFICATION 00 01 15 LIST OF CONTRACT DRAWINGS

SPECIFICATION 00 01 20 LIST OF SCHEDULES

SPECIFICATION 00 31 19 EXISTING CONDITION INFORMATION

SPECIFICATION 00 31 21 SURVEY INFORMATION

SPECIFICATION 00 31 24 ENVIRONMENTAL ASSESSMENT INFORMATION

SPECIFICATION 00 31 26 EXISTING HAZARDOUS MATERIAL INFORMATION

SPECIFICATION 00 31 32 GEOTECHNICAL DATA

SPECIFICATION 00 31 43 PERMIT APPLICATION

DIVISION 01 - GENERAL REQUIREMENTS

SPECIFICATION 01 01 00 IDENTIFICATION OF TECHNICAL SPECIFICATIONS

SPECIFICATION 01 19 00 SCOPE OF WORK

SPECIFICATION 01 27 00 MEASUREMENT AND PAYMENT

SPECIFICATION 01 31 00 PROJECT MANAGEMENT AND COORDINATION

SPECIFICATION 01 32 00 CONSTRUCTION PROGRESS DOCUMENTATION

SPECIFICATION 01 33 00 SUBMITTALS

SPECIFICATION 01 39 00 SAFETY

SPECIFICATION 01 42 00 REFERENCES

SPECIFICATION 01 46 00 QUALITY CONTROL / QUALITY ASSURANCE

SPECIFICATION 01 51 00 TEMPORARY UTILITIES

SPECIFICATION 01 56 00 BARRICADES AND SIGNS

SPECIFICATION 01 57 00 TEMPORARY EROSION, SEDIMENTATION AND

ENVIRONMENTAL CONTROLS

SPECIFICATION 01 59 00 TEMPORARY CONTROLS FOR WORK AREAS / PROJECT-

SPECIFIC LOCATIONS

STANDARD DIVISIONS

USIBWC Contract No.: IBM10BO006-Amendment 5 Page 01.01.00 - 2

SPECIFICATION 01 69 00 CONTROL OF MATERIALS

SPECIFICATION 01 70 00 MOBILIZATION

SPECIFICATION 01 71 00 FIELD ENGINEERING

SPECIFICATION 01 77 00 CONTRACT CLOSE-OUT

DIVISION 02 - EXISTING CONDITIONS

SPECIFICATION 02 02 00 EXISTING CONDITIONS & FACILITIES

SPECIFICATION 02 91 00 INSTALL, REMOVE AND/OR RELOCATE FENCE

DIVISIONS 31 / 33 - SITE GRADING

SPECIFICATION 31 04 00 REMOVING CONCRETE

SPECIFICATION 31 11 00 PREPARING RIGHT OF WAY

SPECIFICATION 31 12 00 OBLITERATE EXISTING ROAD

SPECIFICATION 31 14 00 REMOVE / STOCKPILE EXISTING MATERIALS

SPECIFICATION 31 20 00 CLEAN EXISTING CHANNEL

SPECIFICATION 31 81 00 PROOF ROLLING

SPECIFICATION 31 92 00 VEGETATION FOR EROSION CONTROL

DIVISION 35 - WATERWAY / MARINE

SPECIFICATION 35 41 00 CONSTRUCTION OF LEVEE

SPECIFICATION 35 42 00 WATERWAY BANK PROTECTION

DIVISION 50 - ROADWAY CONSTRUCTION

SPECIFICATION 50 11 00 ROADWAY EMBANKMENT

SPECIFICATION 50 12 00 ROADWAY EXCAVATION

SPECIFICATION 50 20 00 ROADWAY BASE

SPECIFICATION 50 21 00 PRIME COAT

SPECIFICATION 50 22 00 ASPHALT ANTISTRIPPING AGENTS

SPECIFICATION 50 23 00 EQUIPMENT FOR ASPHALT CONCRETE PAVEMENT

SPECIFICATION 50 24 00 ASPHALT, OILS, AND EMULSIONS

SPECIFICATION 50 25 00 HOT MIX ASPHALT CONCRETE PAVEMENT

SPECIFICATION 50 26 00 SURFACE TREATMENTS

SPECIFICATION 50 27 00 AGGREGATES FOR SURFACE TREATMENTS

SPECIFICATION 50 40 00 METAL BEAM GUARD FENCE

SPECIFICATION 50 60 00 CONCRETE PAVEMENT

DIVISION 60 - STRUCTURES

SPECIFICATION 60 02 00 TRENCH EXCAVATION PROTECTION

SPECIFICATION 60 10 00 EXCAVATION AND BACKFILL FOR STRUCTURES

SPECIFICATION 60 20 00 CONCRETE STRUCTURES

SPECIFICATION 60 21 00 HYDRAULIC CEMENT

SPECIFICATION 60 23 00 FLOODWALL

SPECIFICATION 60 24 00 PRECAST CONCRETE STRUCTURES (FABRICATION)

SPECIFICATION 60 25 00 PRECAST PRESTRESSED CONCRETE STRUCTURAL

MEMBERS

SPECIFICATION 60 26 00 PRESTRESSING

SPECIAL DIVISIONS

USIBWC Contract No.: IBM10BO006-Amendment 5 Page 01.01.00 - 3

SPECIFICATION 60 27 00 SURFACE FINISHES FOR CONCRETE

SPECIFICATION 60 34 00 ROADWAY APPROACH SLABS

SPECIFICATION 60 38 00 CLEAN / SEAL JOINTS

SPECIFICATION 60 40 00 REINFORCING STEEL

SPECIFICATION 60 41 00 STEEL STRUCTURES

SPECIFICATION 60 42 00 METAL FOR STRUCTURES

SPECIFICATION 60 45 00 GALVANIZING

SPECIFICATION 60 46 00 CLEANING AND PAINTING STEEL

SPECIFICATION 60 47 00 STRUCTURAL BOLTING

SPECIFICATION 60 48 00 STRUCTURAL FIELD WELDING

SPECIFICATION 60 58 00 WATERPROOFING MEMBRANES FOR STRUCTURES

SPECIFICATION 60 64 00 REINFORCED CONCRETE PIPE

SPECIFICATION 60 66 00 HEADWALLS AND WINGWALLS

SPECIFICATION 60 68 00 SLUICE GATES

SPECIFICATION 60 80 00 FLOODGATES

SPECIFICATION 60 96 00 REMOVING EXISTING STRUCTURES

SPECIFICATION 60 98 00 CLEAN EXISTING STRUCTURES

B. In any case where these technical specifications conflict with the Federal Acquisition Regulations (FAR), FAR requirements will take precedence. In any case where FAR requirements are more strict or impose a higher standard than these technical specifications, FAR requirements will take precedence.

1.2 RELATED DOCUMENTS & PROVISIONS

Other related documents describing the requirements for the Work to be performed include the construction drawings entitled:

United States Section

International Boundary & Water Commission American Recovery and Reinvestment Act of 2009

Upper Rio Grande Flood Control Project

Rehabilitation Improvements for Fort Hancock Reach

In Hudspeth County

United States Section

International Boundary & Water Commission American Recovery and Reinvestment Act of 2009

Upper Rio Grande Flood Control Project

Rehabilitation Improvements for Fabens Reach

In El Paso County

USIBWC Contract No.: IBM10BO006-Amendment 5 Page 01.01.00 - 4

Additionally, other related documents include these technical specifications, and the associated provisions included in the Contract.

1.3 PROVISIONS FOR MEASUREMENT AND PAYMENT

For Work performed by the Contractor under this Contract, the identified technical specifications (as shown in paragraph 1.1 herein) are those under which payment is to be made to the Contractor.

Measurement and payment of work shall be in accordance with SPECIFICATION 01 27 00 of this Contract.

1.4 SPECIFICATION / BID ITEM FORMAT AND CONVENTIONS

A. Specification Format. The technical specifications are organized into Divisions, and identified in Level 2 title format, using the Construction Specifications Institute’s (CSI) "MasterFormat – 2004 Edition" numbering system. For this Contract, the Divisions are grouped in two categories: (1) Standard Divisions, which are Divisions identified and defined by CSI, and (2) Special Divisions, which are Divisions that have been developed using industry standards, for some unique items of Work under this Contract.

B. Bid Item Format. Bid Items under this Contract have been derived from the governing specifications identified in paragraph 1.1 herein. Bid Items are numbered in Level 3 title format, using CSI’s “MasterFormat – 2004 Edition" numbering system. All Bid Items are identified in Section B of the Contract Provisions.

PART 2 – MATERIALS & EQUIPMENT (Not Applicable To This Specification)

PART 3 – CONSTRUCTION (Not Applicable To This Specification)

PART 4 – MEASUREMENT AND PAYMENT (Not Applicable To This Specification)

- END OF SPECIFICATION -