MIL-STD-648E.pdf

AMSC N/A AREA PACK

INCH-POUND

MIL-STD-648E

1 November 2016

SUPERSEDING

MIL-STD-648D

10 April 2008

DEPARTMENT OF DEFENSE

DESIGN CRITERIA STANDARD

SPECIALIZED SHIPPING CONTAINERS

Source: https://assist.dla.mil -- Downloaded: 2017-04-20T13:14Z Check the source to verify that this is the current version before use.

MIL-STD-648E

ii

FOREWORD

1. This standard is approved for use by all Departments and Agencies of the Department of Defense.

2. This standard establishes the general design criteria and associated tests for specialized shipping containers used by the Department of Defense. The initial step in the creation of a specialized shipping container is to distill the general design criteria within this document into specific design criteria. By filling out a container requirements checklist (see Appendix A) prior to initiating the design, a focused list of unique needs can be identified to ensure that the container’s contents are properly protected throughout its planned distribution and stowage logistics.

3. A specialized container is uniquely configured to support and protect its prescribed contents while being handled, stored, shipped to, and unpacked by the user; or to protect personnel and equipment from hazardous contents. Containers of this type frequently incorporate energy absorbing systems, temperature control systems, or special features to make handling or shipment possible, easier, or safer. Engineering drawings, or equivalent, are used to define form, fit, function, materials, tolerances, and manufacturing techniques.

4. A specialized shipping container is designed for use with a specific item when general container specifications are not sufficiently detailed to assure required protection, safety, reliability, maintainability, or configuration control. The need for a specialized container may arise with any deliverable item and invariably does so with nuclear and conventional ammunition and explosives. The container may be the result of a completely original design effort or of the modification of existing or standard container designs.

5. Copies of this standard are available online at http://quicksearch.dla.mil.

6. Comments, suggestions, or questions on this document should be addressed to Commander, Naval Sea Systems Command, ATTN: SEA 05S, 1333 Isaac Hull Avenue, SE, Stop 5160, Washington Navy Yard, DC 20376-5160 or emailed to CommandStandards@navy.mil, with the subject line “Document Comment”. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https://assist.dla.mil.

http://quicksearch.dla.mil/ mailto:CommandStandards@navy.mil https://assist.dla.mil/ iii

CONTENTS

PARAGRAPH PAGE

1. SCOPE

1.1 Scope

2. APPLICABLE DOCUMENTS

2.1 General

2.2 Government documents

2.2.1 Specifications, standards, and handbooks

2.2.2 Other Government documents, drawings, and publications

2.3 Non-Government publications

2.4 Order of precedence

3. DEFINITIONS

3.1 General

3.1.1 Ambient (temperature)

3.1.2 Anthropometry

3.1.3 Clinch

3.1.4 Commercial-off-the-shelf (COTS)

3.1.5 Competent authority

3.1.6 Connected replenishment-at-sea (CONREP)

3.1.7 Cracking pressure (relief valve)

3.1.8 Critical item development specification (CIDS)

3.1.9 Cushion (compressive) creep

3.1.10 Distributed isolation material (DIM)

3.1.11 Elastomer

3.1.12 Energy absorbing devices

3.1.13 Explosive limit

3.1.14 Faying surfaces

3.1.15 Fire-retardant materials

3.1.16 Flexible barriers

3.1.17 Fragility levels

3.1.18 Galling

3.1.19 Grade A container

3.1.20 Grade B container

3.1.21 Hazardous material (HAZMAT)

3.1.22 Human systems integration (HSI)

3.1.23 Hydrogen embrittlement

3.1.24 Hygroscopic

3.1.25 Level A

3.1.26 Level B

3.1.27 Life cycle environmental profile (LCEP)

3.1.28 Minimum flow rate (relief valve)

3.1.29 Nematode

3.1.30 Non-combustible materials

3.1.31 Non-person portable container

3.1.32 Passivation

3.1.33 Performance Oriented Packaging (POP)

3.1.34 Reseal pressure (relief valve)

iv

PARAGRAPH PAGE

3.1.35 Shock response spectrum (SRS)

3.1.36 Specialized shipping container

3.1.37 Springwood

3.1.38 Standard parts and materials

3.1.39 Standard tension replenishment alongside method (STREAM)

3.1.40 Summerwood

3.1.41 Sympathetic reaction

3.1.42 Transmissibility

3.1.43 Underway replenishment at sea (UNREP)

3.1.44 Unitized load

3.1.45 Vertical replenishment (VERTREP)

4. GENERAL REQUIREMENTS

4.1 General

4.1.1 HAZMAT and devices

4.2 Interfaces

4.2.1 Contents

4.2.2 Handling equipment

4.2.3 Distribution network

4.2.4 Unitized load compatibility

4.3 Configuration

4.4 Transportability requirements

4.4.1 Sensitive materials (transportation security)

4.4.2 Transfer-at-sea (UNREP)

4.5 Cube and weight

4.5.1 Naval aircraft carrier container size limits

4.6 Materials and manufacturing methods

4.6.1 Plating

4.6.2 Dissimilar metals

4.6.2.1 Acceptance criteria

4.6.3 Screw threads

4.6.4 Elastomeric parts

4.6.5 Standard parts and materials

4.6.6 Material stability

4.6.7 Internal packaging materials

4.6.7.1 Materials compatibility

4.6.7.2 Wood dunnaging

4.6.7.3 Cushioning materials

4.6.7.4 Resilient mounts

4.6.7.5 Dynamic characteristics

4.6.8 Interchangeability

4.6.9 Fasteners and closure devices

4.6.10 Wood treatment and preservation

4.6.10.1 Nematodes

4.6.11 Nonmetallic materials

4.6.12 Corrosion

4.6.13 Stainless steel

v

PARAGRAPH PAGE

4.7 Fire performance

4.8 Drainage

4.9 Records receptacle

4.10 Closure devices

4.11 Static electricity

4.12 Preservation

4.13 Clean-room operations

4.14 Security seal

4.15 Protection of contents against corrosion and water damage

4.15.1 General

4.15.2 Closed containers without auxiliary barriers

4.15.2.1 Ventilation

4.15.2.2 Drainage

4.15.3 Closed containers with auxiliary barriers

4.15.4 Integral-barrier containers

4.15.4.1 Structural

4.15.4.2 Leakage

4.15.4.3 Closures (except removable head drums)

4.15.4.4 Desiccant storage

4.15.4.5 Humidity indicator

4.15.4.6 Pressurizing fitting

4.15.4.7 Leakage indicator

4.15.4.8 Container accessories

4.15.4.9 Transparent window in auxiliary barrier

4.15.4.10 Special requirements for non-breathing integral-barrier containers

4.15.4.11 Special requirements for controlled-breathing integral-barrier containers

4.15.4.12 Special requirements for free-breathing containers

4.15.4.13 Observation window

4.15.4.13.1 Alternate observation window location

4.16 Stacking and stowing

4.16.1 General

4.16.2 Stacking stability

4.16.3 Stackability

4.16.4 Distributed load

4.16.5 Stacking strength

4.17 Handling

4.17.1 General

4.17.2 Manual lifting/carrying

4.17.2.1 Handle characteristics

4.17.2.2 Handhold characteristics

4.17.3 Hoisting

4.17.3.1 External air transport

4.17.3.2 Hoisting provisions

4.17.4 Tiedown

4.17.5 Skids

4.17.6 Forklift truck compatibility

vi

PARAGRAPH PAGE

4.17.6.1 Containers having a length greater than 88 inches

4.17.6.2 Containers ranging in length from 50 to 88 inches

4.17.6.3 Pallet size containers (52 by 44 inches or smaller)

4.17.6.4 Direct interface with military aircraft loading operations

4.17.6.5 Secondary uses for fork pockets

4.17.7 Pallet jack compatibility

4.17.8 Shipboard handling

4.17.9 Handling provision maintainability

4.18 Special protection devices

4.18.1 Temperature control

4.18.2 Field-force protection

4.18.3 Magnetic shielding

4.19 Protecting and identifying the container

4.19.1 Painting requirements

4.19.2 Identification and instructional markings

4.19.2.1 Identification marking

4.19.2.2 Basic instructional markings

4.19.3 Container markings

4.20 NBC survivability

4.21 HSI

5. DETAILED REQUIREMENTS

5.1 Fit and compatibility

5.1.1 General

5.1.2 Fit test

5.2 Mechanical shock

5.2.1 General

5.2.1.1 Acceptance criteria

5.2.1.2 Test loads

5.2.1.3 Instrumentation

5.2.1.4 Temperature combined with shock

5.2.1.5 Drop surface

5.2.2 Repetitive shock test

5.2.2.1 Repetitive shock test (stacked)

5.2.3 Drop test (free-fall)

5.2.4 Cornerwise-drop (rotational) test

5.2.5 Edgewise-drop (rotational) test

5.2.6 Impact test

5.2.6.1 Truck transport

5.2.6.2 Rail transport

5.2.6.3 Impact test (stacked)

5.2.7 Transfer-at-sea shock test

5.2.8 Tipover test

5.2.9 Shipboard shock test

5.2.9.1 Shipboard shock test (eligibility)

5.2.9.2 Pass-fail criteria

5.2.9.3 Grades of containers

vii

PARAGRAPH PAGE

5.2.9.4 Classes of containers

5.2.9.5 Class I containers (foam or rubberized fiber isolation systems)

5.2.9.5.1 Container testing

5.2.9.5.2 Weight limitations

5.2.9.5.3 Size limitations

5.2.9.5.4 Testing orientations

5.2.9.5.5 Method of securing the container to the MWSM

5.2.9.5.6 Design criteria

5.2.9.5.7 FSP testing

5.2.9.5.8 Deck-stowed containers

5.2.9.5.9 Method of securing the container to the FSP

5.2.9.6 Class II containers (resilient mount isolation systems)

5.2.9.6.1 Testing to HI-shock events

5.2.9.7 Chain tiedown assembly

5.2.10 Safety drop test

5.3 Vibration

5.3.1 General

5.3.2 Random vibration

5.3.2.1 Truck transportation over U.S. highway

5.3.2.2 Mission/field transportation

5.3.2.3 Jet aircraft

5.3.2.4 Propeller aircraft

5.3.2.5 Shipboard

5.3.3 Sinusoidal testing

5.3.3.1 Resonance survey and dwell test

5.3.4 Sinusoidal cycling test

5.4 Structural integrity

5.4.1 General

5.4.2 Pressure test

5.4.2.1 Test pressures

5.5 Leakage integrity

5.5.1 General

5.5.2 Leak test

5.5.2.1 Test pressures

5.6 Superimposed load

5.6.1 General

5.6.2 Load test (like containers)

5.6.3 Load test (unlike containers)

5.7 Hoisting fittings, closure fittings, and tiedown attachment points

5.7.1 General

5.7.2 Acceptance criteria

5.7.3 Hoisting fittings strength test

5.7.4 Single hoisting fitting strength test

5.7.5 Tiedown strength test

5.7.6 Closure fitting strength test

5.8 Forklift truck (fully captive fork tine enclosures) compatibility test viii

PARAGRAPH PAGE

5.8.1 Forklift truck (non-captive lift) compatibility test

5.9 Handlift truck MK 45 compatibility

5.9.1 General

5.9.2 Static overload

5.9.3 Shock test

5.9.4 Rolling test

5.10 Fire performance requirements

5.10.1 Flame spread index test

5.10.2 Smoke density test

5.10.3 Stacked container fire test

5.11 Measurement of magnetic fields

5.12 Insensitive munitions

5.13 POP testing for HAZMAT

5.14 Certificate of equivalency (COE)

5.15 Testing sequences

5.15.1 Army containers

5.15.2 Air Force containers

5.15.3 Navy containers

6. NOTES

6.1 Intended use

6.2 Acquisition requirements

6.3 Subject term (key word) listing

6.4 International standardization agreement implementation

6.5 Changes from previous issue

APPENDIX PAGE

APPENDIX A. CONTAINER REQUIREMENTS CHECKLIST

A.1 SCOPE

A.1.1 Scope

APPENDIX B. DRAWINGS OF COMMON STANDARD PARTS FOR NAVY CONTAINERS

B.1 SCOPE

B.1.1 Scope

APPENDIX C. ELECTROSTATIC PROPERTIES OF MATERIALS

C.1 SCOPE

C.1.1 Scope

C.2 DEFINITION

C.2.1 Electrostatic properties

C.3 APPARATUS

C.4 SPECIMENS

C.5 CONDITIONING

C.5.1 Test environment

C.6 PROCEDURE

C.7 NOTES

ix

APPENDIX PAGE

APPENDIX D. SUPERIMPOSED-LOAD TEST (STACKABILITY, WITH DUNNAGE)

D.1 SCOPE

D.1.1 Scope

D.2 DEFINITIONS

D.2.1 Top dunnage

D.3 APPARATUS

D.3.1 Top superimposed-load test

D.4 SPECIMEN

D.4.1 Contents of container

D.5 CONDITIONING

D.5.1 Test specimen

D.6 PROCEDURE

D.7 NOTES

APPENDIX E. SUPERIMPOSED-LOAD TEST (UNIFORMLY DISTRIBUTED, WITHOUT DUNNAGE)

E.1 SCOPE

E.1.1 Scope

E.2 DEFINITIONS

E.2.1 Packing E.2.1.1 Level A E.2.1.2 Level B

E.2.2 Top dunnage

E.3 APPARATUS

E.3.1 Top superimposed-load test

E.4 SPECIMEN

E.4.1 Contents of container

E.5 CONDITIONING

E.5.1 Test specimen

E.6 PROCEDURE

E.7 NOTES

APPENDIX F. VIBRATION (REPETITIVE SHOCK) TEST

F.1 SCOPE

F.1.1 Scope

F.2 DEFINITIONS

F.2.1 Shock F.2.2 Vibration

F.3 APPARATUS

F.3.1 Platform F.3.2 Restraining devices

F.4 SPECIMENS

F.4.1 Contents of container

F.5 CONDITIONING

F.5.1 Test specimen

F.6 PROCEDURE

x

APPENDIX PAGE

APPENDIX G. FREE-FALL DROP TEST

G.1 SCOPE

G.1.1 Scope

G.2 APPARATUS

G.3 SPECIMEN

G.3.1 Contents of container

G.4 CONDITIONING

G.4.1 Test specimen

G.5 PROCEDURE

G.5.1 Bags G.5.2 Cylindrical containers G.5.3 Rectangular containers G.5.4 Drop height

G.6 NOTES

APPENDIX H. CORNERWISE-DROP (ROTATIONAL) TEST

H.1 SCOPE

H.1.1 Scope

H.2 DEFINITIONS

H.2.1 Large shipping containers

H.3 APPARATUS

H.3.1 Cornerwise-drop test

H.4 SPECIMEN

H.4.1 Contents of container

H.5 CONDITIONING

H.5.1 Test specimen

H.6 PROCEDURE

H.6.1 Number and height of drops

H.7 NOTES

APPENDIX I. EDGEWISE-DROP (ROTATIONAL) TEST

I.1 SCOPE

I.1.1 Scope

I.2 DEFINITIONS

I.2.1 Large shipping containers

I.3 APPARATUS

I.3.1 Edgewise-drop test

I.4 SPECIMEN

I.4.1 Contents of container

I.5 CONDITIONING

I.5.1 Test specimen

I.6 PROCEDURE

I.6.1 Number and height of drops

I.7 NOTES

xi

APPENDIX PAGE

APPENDIX J. TIPOVER TEST

J.1 SCOPE

J.1.1 Scope

J.2 DEFINITION

J.2.1 Large shipping containers

J.3 APPARATUS

J.3.1 Tipover test

J.4 SPECIMEN

J.4.1 Contents of container

J.5 CONDITIONING

J.5.1 Test specimen

J.6 PROCEDURE

J.6.1 Number and direction of tipover

J.7 NOTES

APPENDIX K. ROLLOVER TEST

K.1 SCOPE

K.1.1 Scope

K.2 APPARATUS

K.3 SPECIMEN

K.3.1 Contents of container

K.4 CONDITIONING

K.4.1 Test specimen

K.5 PROCEDURE

K.6 NOTES

APPENDIX L. INCLINE-IMPACT TEST

L.1 SCOPE

L.1.1 Scope

L.2 DEFINITION

L.2.1 Incline impact tester

L.3 APPARATUS

L.3.1 Inclined track

L.4 SPECIMEN

L.4.1 Contents of container

L.5 CONDITIONING

L.5.1 Test specimen

L.6 PROCEDURE

L.7 NOTES

APPENDIX M. PENDULUM-IMPACT TEST

M.1 SCOPE

M.1.1 Scope

M.2 DEFINITION

M.2.1 Large shipping containers xii

APPENDIX PAGE

M.3 APPARATUS

M.3.1 Pendulum-impact tester

M.4 SPECIMEN

M.4.1 Contents of container

M.5 CONDITIONING

M.5.1 Test specimen

M.6 PROCEDURE

M.7 NOTES

APPENDIX N. VIBRATION (SINUSOIDAL MOTION) TEST

N.1 SCOPE

N.1.1 Scope

N.2 DEFINITION

N.2.1 Octave

N.3 APPARATUS

N.3.1 Platform N.3.2 Fixture N.3.3 Instrumentation

N.4 SPECIMENS

N.4.1 Contents of container

N.5 CONDITIONING

N.5.1 Test specimen

N.6 PROCEDURE

APPENDIX O. LEAKS IN CONTAINERS

O.1 SCOPE

O.1.1 Scope

O.2 DEFINITIONS

O.2.1 Leak O.2.2 Leakage

O.3 APPARATUS

O.4 SPECIMEN

O.4.1 Contents of container

O.5 CONDITIONING

O.5.1 Test specimen

O.6 PROCEDURE

O.6.1 Vacuum retention technique O.6.2 Vacuum chamber technique O.6.3 Pneumatic pressure technique O.6.4 Squeeze technique O.6.5 Hot water technique O.6.6 Submersion (or immersion) techniques O.6.7 Simulated rainfall technique O.6.8 Hydraulic pressure technique O.6.9 Static technique xiii

APPENDIX PAGE

O.7 NOTES

O.7.1 Selection of technique

APPENDIX P. MECHANICAL HANDLING TEST

P.1 SCOPE

P.1.1 Scope

P.2 APPARATUS

P.2.1 Forklift handling P.2.2 Hoisting with slings P.2.3 Hoisting with grabs P.2.4 Pushing P.2.5 Towing P.2.6 Conveying

P.3 SPECIMEN

P.3.1 Contents of container

P.4 CONDITIONING

P.4.1 Test specimen

P.5 PROCEDURE

P.5.1 Handling provisions P.5.2 Lifting and transporting by forklift truck P.5.3 Pushing test (flat)

P.5.3.1 Pushing test (lifted) P.5.4 Towing

P.5.4.1 Additional towing test P.5.5 Hoisting with slings

P.5.5.1 Undersling handling P.5.5.2 Sling handling with attachments

P.5.6 Hoisting with grabs P.5.7 Conveying P.5.8 Inspection after handling

P.6 NOTES

P.6.1 Test procedure

APPENDIX Q. MINIMIZATION OF HYDROGEN EMBRITTLEMENT IN PH 17-4/7 H900 COUPLED WITH

ALUMINUM IN PHST CENTER DESIGNED EQUIPMENT

Q.1 SCOPE

Q.1.1 Scope xiv

FIGURE PAGE

1. View of STREAM trolley and transfer strongback

2. Standard fork tine spacings

3. Pallet size container fork tine spacings

4. Samples of symmetrical packaging

5. Front view of stacked container fire test setup

6. Plan view of stacked container fire test setup

7. Army test sequence for containers under 150 pounds and issued to ground troops

8. Army test sequence for containers 150 pounds or more and issued to ground troops

9. Air Force test sequence for containers under 150 pounds

10. Air Force test sequence for containers 150 pounds or more B-1. Records holder (Drawing 799AS105) B-2. Center lift (Drawing 3214AS110) B-3. Holder, records (Drawing 5166322) B-4. Plug, humidity indicator (Drawing 5166628) B-5. Endlift-adapter (Drawing 5167401) B-6. Fork pocket (Drawing 5167633) B-7. Fork pocket (Drawing 5167693) B-8. Handle (Drawing 6212630) B-9. Observation window (Drawing 6212706) B-10. Access port (Drawing 6212707) B-11. Shackle (Drawing 6212862) B-12. Valve, breather (Drawing 6212863) B-13. Desiccator (Drawing 6212868) B-14. Latch (Drawing 6213102 B-15. Ring, container lift (Drawing 6214106) B-16. Container endlift interface (Drawing 6214131, sheet 1 of 3) C-1. Electrostatic test chamber C-2. Electrostatic test arrangement C-3. Electrostatic test C-4. Electrostatic detector C-5. Electrode D-1. Top superimposed-load test (stackability, with dunnage) E-1. Top superimposed-load test (uniformly distributed, without dunnage) G-1. Free-fall drop test H-1. Cornerwise drop (rotational) I-1. Edgewise drop (rotational) L-1. Incline-impact test M-1. Pendulum-impact test without platform M-2. Pendulum-impact test P-1. Slings placed around specimen with load superimposed P-2. Hoisting with sling attachment provisions P-3. Hoisting with grabs xv

TABLE PAGE

I. Common standard parts for Navy containers II. Expected temperature extremes III. Mechanical shock input locations to containers IV. Shock test for containers-at-sea G-I. Height of free-fall drops for containers of various sizes and weights H-I. Height of rotational drops for containers of various sizes and weights I-I. Height of rotational drops for containers of various sizes and weights

1. SCOPE

1.1 Scope. This standard establishes general design guidelines and associated tests for specialized shipping containers used by the Department of Defense. Definitive requirements for specific containers will be defined by the individual specification, acquisition, or task order. This standard is intended to be used as the basic reference document in all specifications and standards prescribing performance requirements to be applied to a specialized shipping container. Compliance with this intent is expected through normal application of the specification or standard preparation and revision processes.

2. APPLICABLE DOCUMENTS

2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this standard. This section does not include documents cited in other sections of this standard or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3, 4, or 5 of this standard, whether or not they are listed.

2.2 Government documents.

2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

INTERNATIONAL STANDARDIZATION AGREEMENTS

STANAG 2828 - Military Pallets, Packages and Containers

STANAG 2829 - Material Handling Equipment

STANAG 4240 - Liquid Fuel/External Fire, Munition Test Procedures

STANAG 4241 - Bullet Impact, Munition Test Procedures

STANAG 4375 - Safety Drop, Munition Test Procedures

STANAG 4382 - Slow Heating, Munitions Test Procedures

STANAG 4396 - Sympathetic Reaction, Munition Test Procedures

STANAG 4496 - Fragment Impact, Munitions Test Procedure

STANAG 4526 - Shaped Charge Jet, Munitions Test Procedure

FEDERAL STANDARDS

FED-STD-H28 - Screw-Thread Standards for Federal Services

COMMERCIAL ITEM DESCRIPTIONS

A-A-55057 - Panels, Wood/Wood Based; Construction and Decorative

DEPARTMENT OF DEFENSE SPECIFICATIONS

MIL-S-901 - Shock Tests, H.I. (High-Impact) Shipboard Machinery, Equipment, and Systems, Requirements for

MIL-DTL-2427 - Box, Ammunition Packing: Wood, Nailed

MIL-D-3464 - Desiccants, Activated, Bagged, Packaging Use and Static Dehumidification

MIL-D-3716 - Desiccants, Activated for Dynamic Dehumidification

MIL-DTL-53072 - Chemical Agent Resistant Coating (CARC) System Application Procedures and Quality Control Inspection

MIL-PRF-81705 - Barrier Materials, Flexible, Electrostatic Discharge Protective, Heat-Sealable

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-129 - Military Marking for Shipment and Storage

MIL-STD-130 - Identification Marking of U.S. Military Property

MIL-STD-209 - Lifting and Tiedown Provisions

MIL-STD-709 - Ammunition Color Coding

MIL-STD-810 - Environmental Engineering Considerations and Laboratory Tests

MIL-STD-814 - Requirements for Tiedown, Suspension and Extraction Provisions on Military Materiel for Airdrop

MIL-STD-889 - Dissimilar Metals

MIL-STD-913 - Requirements for the Certification of Sling Loaded Military Equipment for External Transportation by Department of Defense Helicopters

MIL-STD-1320 - Standard Practice for Designing Unit Loads, Truckloads, Railcar Loads, and Intermodal Loads for Ammunition and Explosives

MIL-STD-1365 - General Design Criteria for Handling Equipment Associated with Weapons and Related Items

MIL-STD-1366 - Transportability Criteria

MIL-STD-1472 - Human Engineering

MIL-STD-1660 - Ammunition Unit Loads

MIL-STD-1686 - Electrostatic Discharge Control Program for Protection of Electrical and Electronic Parts, Assemblies and Equipment (Excluding Electrically Initiated Explosive Devices)

MIL-STD-1791 - Designing for Internal Aerial Delivery in Fixed Wing Aircraft

MIL-STD-1904 - Design and Test Requirements for Level A Ammunition Packaging

MIL-STD-2073-1 - Military Packaging

MIL-STD-2105 - Hazard Assessment Tests for Non-Nuclear Munitions

MIL-STD-3010 - Test Procedures for Packaging Materials and Containers

MIL-STD-3028 - Joint Modular Intermodal Container

DEPARTMENT OF DEFENSE HANDBOOKS

MIL-HDBK-304 - Package Cushioning Design

DOD-HDBK-743 - Anthropometry of U.S. Military Personnel (Metric)

(Copies of these documents are available online at http://quicksearch.dla.mil.)

Source: https://assist.dla.mil -- Downloaded: 2017-04-20T13:14Z http://quicksearch.dla.mil/

2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.

CODE OF FEDERAL REGULATIONS (CFR)

40 CFR 261.24 - Protection of Environment, Identification and Listing of Hazardous Waste, Toxicity Characteristic

49 CFR Parts 100-180 - Transportation, Chapter 1, Pipeline and Hazardous Materials Safety Administration, Department of Transportation

(Copies of these documents are available online at https://www.gpo.gov/fdsys/search/home.action.)

DEPARTMENT OF THE ARMY DOCUMENTS

TP-94-01 Revision 2 - Transportability Test Procedures

(Copies of this document are available online at http://www3.dac.army.mil.)

DEPARTMENT OF DEFENSE JOINT SERVICE DOCUMENTS

(The following publication is jointly issued for the Department of Defense. Each service refers to the document using its unique numbering system. The numbers listed are for the Air Force, Army, Navy, Marine Corps, and Defense Logistics Agency.)

Air Force Regulation (AFR) 80-18 Army Regulation (AR) 70-44 Naval Operations Instruction

(OPNAVINST) 4600.22

Marine Corps Order (MCO) 4610.14 Defense Logistics Agency Regulation

(DLAR) 4500.25

- DoD Engineering for Transportability

(Copies of this document are available online at http://www.dla.mil, http://www.army.mil/usapa/epubs, http://www.usmc.mil/directiv.nsf/web+orders, or http://usahec.contentdm.oclc.org/cdm/ref/collection/p16635coll11/id/802.)

(The following publication is jointly issued for the Department of Defense. Each service refers to the document using its unique numbering system. The numbers listed are for the Air Force, Army, Navy Supply Systems Command, Marine Corps, and Defense Logistics Agency.)

Air Force Manual (AFM) 24-210 Army Regulation (AR) 700-143 Naval Supply Corps System Command Instruction (NAVSUPINST) 4030.55 Marine Corps Order (MCO) 4030.40 Defense Logistics Agency Regulation

(DLAR) 4145.41

- Packaging of Hazardous Material

(Copies of this document are available online at http://www.dla.mil, http://www.army.mil/usapa/epubs, http://www.usmc.mil/directiv.nsf/web+orders, https://nll2.ahf.nmci.navy.mil/default.cfm, or http://www.e-publishing.af.mil.)

Source: https://assist.dla.mil -- Downloaded: 2017-04-20T13:14Z Check the source to verify that this is the current version before use.

https://www.gpo.gov/fdsys/search/home.action http://www3.dac.army.mil/ http://www.dla.mil/ http://www.army.mil/usapa/epubs/ http://www.usmc.mil/directiv.nsf/web+orders http://usahec.contentdm.oclc.org/cdm/ref/collection/p16635coll11/id/802 http://www.dla.mil/ http://www.army.mil/usapa/epubs/ http://www.usmc.mil/directiv.nsf/web+orders https://nll2.ahf.nmci.navy.mil/default.cfm http://www.e-publishing.af.mil/

Army Regulation (AR) 70-75 - Survivability of Army Personnel and Materiel

(Army application for publication copies should be addressed to: Army Publishing Directorate, 9351 Hall Rd., Fort Belvoir, VA 22060.)

Test Operations Procedure (TOP) 8-2-111 - Chemical, Biological, and Radiological (CBR) Contamination Survivability, Small Items of Equipment

(Copies of this document are available online at http://www.dtic.mil/whs/directives/.)

DEPARTMENT OF DEFENSE ISSUANCES

DOD 4140.65-M - Issue, Use, and Disposal of Wood Packaging Material (WPM)

DODI 5100.76 - Safeguarding Sensitive Conventional Arms, Ammunition, and Explosives

(AA&E)

(Copies of these documents are available online at http://www.dtic.mil/whs/directives/.)

DEPARTMENT OF THE NAVY DOCUMENTS

NWP 4-01.4 - Underway Replenishment

(Copies of this document are available online at http://www.maritime.org/doc/pdf/unrep-nwp04-01.pdf.)

MILITARY STANDARD (MS) DRAWING

MS17868 - Indicator, Propellant Leak, Plug, Color Change, for Unsymmetrical Dimethylhydrazine and Fuming Nitric Acid

(Copies of this document are available online at http://quicksearch.dla.mil.)

DTIC TECHNICAL REPORTS

Technical Report 93003 - Weapons Container Stacking Study

(Copies of this document are available online at http://www.dtic.mil.)

NAVAL AIR SYSTEMS COMMAND (NAVAIR) DRAWINGS

799AS105 - Records Holder

3214AS110 - Center Lift

2602910 - Decal, Leak Detector

(Copies of these documents are available online at https://mynatec.navair.navy.mil.)

NAVAL SEA SYSTEMS COMMAND (NAVSEA) DRAWINGS

5166322 - Holder, Records

5166628 - Plug, Humidity Indicator

5167399 - Extrusion, Endlift

5167401 - Endlift-Adapter

5167633 - Fork Pocket

5167693 - Fork Pocket

6212630 - Handle

Source: https://assist.dla.mil -- Downloaded: 2017-04-20T13:14Z Check the source to verify that this is the current version before use.

http://www.dtic.mil/whs/directives/ http://www.dtic.mil/whs/directives/ http://www.maritime.org/doc/pdf/unrep-nwp04-01.pdf http://quicksearch.dla.mil/ http://www.dtic.mil/ https://mynatec.navair.navy.mil/

6212706 - Observation Window

6212707 - Access Port

6212862 - Shackle

6212863 - Valve, Breather

6212868 - Desiccator

6212876 - Beam, Container Handling MK 52 MOD 0

6213102 - Latch

6213893 - Beam, Container H