TDP_added_Drawings.pdf

cborcher Current Contract 1-12

A10526F

COPYRIGHT 1991-2014 GENERAL DYNAMICS ORDNANCE AND TACTICAL SYSTEMS, INC.

ii

SPECIFICATION CHANGE LOG

REVISION

CN NUMBER

DATE

PARAGRAPHS AFFECTED

APPROVED

A

A10526-1

8/6/93

General Change

G. B. Coates

B

A10526-2

4/30/96

C

A10526-3

2/22/02

Changed 2.1, 2.2, and 3.1

T. J. Sweeney

D

A10526-4

5/17/02

E

A10526-5

7/26/06

Changed 3.1

F

A10526-6

03/04/14

Changed 2.2 and 3.1.

D.B. Fitzgerald

04 March 2014

COPYRIGHT 1991-2014 GENERAL DYNAMICS ORDNANCE AND TACTICAL SYSTEMS, INC.

1. SCOPE

1.1 This specification establishes the requirements for interchangeable use, in the manufacture of piece parts, of the following corrosion resistant steels:

a. Class 301

b. Class 302

c. Class 303

d. Class 304

e. Class 304L

f. Class 305

g. Class 309

h. Class 310

i. Class 316

j. Class 316L

k. Class 317

l. Class 321

m. Class 347.

2. APPLICABLE DOCUMENTS

2.1 Government documents. The following documents form a part of this specification to the extent specified herein. Unless a specific issue is specified, the latest revision shall apply. In the event of conflict between the documents referenced herein and the contents of this specification, the contents of this specification shall be considered a superseding requirement.

SPECIFICATIONS:

Military

MIL-T-5695 Tubing, Steel, Corrosion-Resistant (304), Cold Drawn

MIL-T-8504 Tubing, Corrosion-Resistant (304), Aerospace Vehicle Hydraulic Systems, Annealed, Seamless and Welded

MIL-T-8808 Tubing, Steel, Corrosion-Resistant (18-8 Stabilized), Aircraft Hydraulic Quality

(Copies of specifications, standards, drawings, and publications required in connection with specified procurement functions should be obtained from the Standardization Document Order Desk, 700 Robbins Avenue, Building Number 4, Section D, Philadelphia, Pennsylvania 19111- 5094.)

COPYRIGHT 1991-2014 GENERAL DYNAMICS ORDNANCE AND TACTICAL SYSTEMS, INC.

2.2 Non-Government documents. The following documents form a part of this specification to the extent specified herein. Unless a specific issue is specified, the latest revision shall apply. In the event of conflict between the documents referenced herein and the contents of this specification, the contents of this specification shall be considered a superseding requirement.

SPECIFICATIONS:

American Society for Testing and Materials (ASTM)

A 167 Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip, Specification for

A 240 Heat-Resisting Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels, Standard Specification for

A 269 Seamless and Welded Austenitic Stainless Steel Tubing for General Service, Specification for

A 276 Stainless Steel Bars and Shapes, Standard Specification for

A 511 Seamless Stainless Steel Mechanical Tubing, Specification for

A 582 Free-Machining Stainless and Heat-Resisting Steel Bars, Hot-Rolled or Cold-Finished, Specification for

(Application for copies should be addressed to the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.)

COPYRIGHT 1991-2014 GENERAL DYNAMICS ORDNANCE AND TACTICAL SYSTEMS, INC.

SPECIFICATIONS: (continued)

Society of Automotive Engineers (SAE)

Aerospace Material Specifications (AMS)

AMS 5517 Steel, Corrosion Resistant, Sheet and Strip 18Cr - 8Ni (SAE 30301) Cold Rolled, 125 ksi (862 MPa) Tensile Strength

AMS 5518 Steel, Corrosion Resistant, Sheet and Strip 18Cr - 8Ni (SAE 30301) Cold Rolled, 150 ksi (1034 MPa) Tensile Strength

AMS 5519 Steel, Corrosion Resistant, Sheet and Strip 18Cr - 8Ni (SAE 30301) Cold Rolled, 185 ksi (1276 MPa) Tensile Strength

AMS 5560 Steel, Corrosion Resistant, Seamless Tubing

AMS 5565 Steel, Corrosion Resistant, Welded Tubing

AMS 5901 Steel Sheet, Strip, and Plate, Corrosion Resistant 18Cr - 8Ni (SAE 30301) Solution Heat Treated

AMS 5902 Steel Sheet and Strip, Corrosion Resistant 18Cr - 8Ni (SAE 30301) Cold Rolled, 175 ksi (1207 MPa) Tensile Strength

AMS-QQ-S-763 Steel Bars, Wire, Shapes, and Forgings, Corrosion Resisting

(Application for copies should be addressed to the Society of Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096.)

3. REQUIREMENTS

3.1 Interchangeability. The following corrosion resistant steels may be used interchangeably in the manufacture of piece parts. All classes may be used interchangeably; however, when a specific class is defined on the drawing only that class shall be used. Bar, strip, sheet, plate, or tubing materials may be used interchangeably provided they conform to any one of the following specifications:

COPYRIGHT 1991-2014 GENERAL DYNAMICS ORDNANCE AND TACTICAL SYSTEMS, INC.

a. Bar:

1. SAE AMS-QQ-S-763, Condition A, Hot or Cold Finished (Class 302, 304, 304L, 305, 309, 310, 316, 316L, 317)

2. ASTM A 276, Condition A, Hot or Cold Finished (Class 302, 304, 304L, 305, 309, 310, 316, 316L, 317, 321, 347)

3. ASTM A 582, Condition A, Finish Optional (Class 303)

b. Plate:

1. ASTM A 240, Condition A, Finish 1 or 4 (Class 304, 304L, 316, 316L, 321, 347)

2. ASTM A 167, Hot Rolled, Finish 1 or 4 (Class 304, 304L, 316, 316L, 321, 347)

c. Sheet:

1. ASTM A 240, Condition A, Finish 2B or 4 (Class 304, 304L, 316, 316L, 321, 347)

2. ASTM A 167, Cold Rolled, Finish 2B or 4 (Class 304, 304L, 316, 316L, 321, 347)

d. Strip:

1. ASTM A 240, Condition A, Finish 1 or 2 (Class 304, 304L, 316, 316L, 321, 347)

2. ASTM A 167, Cold Rolled, Finish 1 or 2 (Class 304, 304L, 316, 316L, 321, 347)

e. Tubing:

1. MIL-T-5695, Seamless or Welded (Class 304)

2. MIL-T-8504, Seamless or Welded (Class 304)

3. SAE AMS 5560, Steel, Corrosion Resistant, Seamless Tubing

4. SAE AMS 5565, Steel, Corrosion Resistant, Welded Tubing

5. MIL-T-8606, Seamless or Welded (Class 304, 321)

6. MIL-T-8808, Seamless or Welded (Class 321)

7 ASTM A 269, Seamless or Welded (Class 304, 304L, 316, 316L, 317, 321, 347)

8. ASTM A 511, Seamless (All classes applicable to this specification)

COPYRIGHT 1991-2014 GENERAL DYNAMICS ORDNANCE AND TACTICAL SYSTEMS, INC.

f. Plate/Sheet/Strip:

1. Class 301 (UNS S30100):

(a) Annealed: AMS 5901

(b) 1/4: AMS 5517

(c) 1/2: AMS 5518

(d) 3/4: AMS 5902

(e) Full Hard: AMS 5519.

3.2 Fusion welding. Only Classes 304L, 316L, or 347 shall be used for fusion welding applications.

3.3 Annealed material. Annealed material shall not be substituted for 1/4, 1/2, 3/4, or full hard material.

4. NOTES

4.1 General. The following subparagraphs provide cautionary information to be considered when calling out this specification.

4.1.1 Cold forming of material. When annealed material is specified; 1/4, 1/2, 3/4, or full hard material may crack during cold forming operations.

4.1.2 Spot welding. This specification shall not be used when the material is to be resistance spot welded.

4.2 Class/type. Documentation for corrosion resistant steels use both the term ”class” and the term ”type” to categorize material. This specification standardizes on ”class” to cover both terms.

4.3 Revision identification. The margins of this specification are marked with change bars to indicate where changes (additions, modifications, corrections, deletions) from the previous issue were made. This was done as a convenience only and General Dynamics Armament and Technical Products assumes no liability whatsoever for any inaccuracies in these notations.

Evaluation of the requirements of this document should be based on the entire content irrespective of the marginal notation and relationship to the last previous issue. In the event of extensive revision to the specification, symbols will not be used to identify changes.

FA8252-12-C-0002