Exhibit_A _Dorm_Furniture_Description_FY16.docx

EXHIBIT A, Dorm Furniture Description

- 96.5cm x 203.5cm x 50cm high

DESCRIPTION:

- 50mm X 30mm metal tubular perimeter frame with 14 arched multi-layer wooden slats set into metal tube with rubber end caps. Four elastic retaining belts are interwoven between slats. Legs are 50mm in diameter x 45cm long with plastic end caps. Legs screw into metal corner gusset plates welded to the tubular frame.

HARDWARE:

- Headboard fixing brackets (2 ea)

FINISH:

- Black

MATERIAL:

Top Plastic laminate, Wilson Art 7054-60 and balanced backer on a 3/4” 45lb. particle board core.

Internal edgebanding:

1 Long – 3/4” x 3” Solid Birch 2 Short – 3/4” x 7/8” Solid Birch 1 Long – 3/4” x 1/8” Solid Birch Sides: 3/4” Birch Veneer Plywood with solid Birch veneer edgebanding Back: 3/4” Birch Veneer Plywood Bottom: 3/4” Birch Veneer Plywood Top Spreader: 3/4” Solid Birch Bottom Spreader: 3/4” Solid Birch Door: 3/4” Birch Veneer Plywood with 3mm solid Birch edgebanding around perimeter Door Hinges: 2-1/2” Black metal inset heavy duty hinge Door Catch: Magnetic Door Pull: 96 MM Black metal curved pull Floor Glides: Nylon to prevent rusting and marking of floors.

CONSTRUCTION:

Sides are screwed to the top, bottom, and back utilizing ¾” x ¾” hardwood cleats. Top and bottom spreaders at the door opening are pocket screwed to the sides. Back shall be fitted into dado grooves cut along the back of the sides and securely screwed in place. Door hinges shall be thru-bolted to the door and sides.

FINISH:

Finish materials shall be of best quality to give hard durable smooth, liquid resistant finish. All surfaces exposed to view in normal use shall be smoothly machined and sanded. The application of finishing materials shall be controlled to produce items of uniform finish without sags, runs, orange peel, overspray or other defects detrimental to a smooth quality appearance. Finish shall be UV cured urethane and/or water base acrylic. Finishing process shall be environmentally friendly and emit no V.O.C.’s (Volatile Organic Compounds) into the atmosphere.

Stain Color:

Wild Cherry

- Long 38" x 80". innerspring unit shall consist of no less than 364 coils. Not less than 12 3/4 gauge tempered high carbon steel wire and height of 5". No less than three active turns per coil. Transverse rows of coils shall be connected by bonnell wires, running at right angles to the long axis of the unit. there shall be a border wire of not less than 6 gauge high carbon steel around the entire perimeter of the top and bottom surfaces of the unit, attached to each outside coil with high carbon spring wire helical. Insulators the entire area of the top and bottom surfaces shall be covered with a heavy duty polyester insulator pad no less than 5/8" thickness.

Filling and Upholstery:

- The top and bottom surfaces each shall have distributed equally over them not less than six pounds per side of boric acid treated cotton batting felt, which shall be wrapped around border wire. the mattress shall contain a total of nine pounds of boric acid treated cotton batting felt not including the corners, which is to be an amount adequate to support the border ticking, in addition, there shall be one polyurethane foam topper later that will be not less than 1/2" in total thickness.

Flange:

- Flange material of not less than 5 1/2" width and adequate to properly secure mattress panels to the innerspring unit by hog ringing every other coil around the entire mattress perimeter of both surfaces.

Border: There shall be a prebuilt, one piece border vertically stitched, at maximum intervals of 2 " to cellular polyethylene not less than 5" wide and 5/32" thick. Ticking:

- The ticking shall be a contract blue damask cover quilted to not less than 1/2" medium density foam. Each top and border panel shall be of one piece (no seams), and shall be double stitched to the pre-built border with not less than 78" wide binding tape.

Machine stitching:

- Machine stitching shall be done with synthetic fiber thread at a rate of not less than 8 stitches to the inch.

Color:

- Blue Damask

- Width 42" Depth 19-13/16" Height 29-3/4" MATERIAL:

- Curved Top Plastic laminate, Wilson Art 7054-60 and balanced backer on a 3/4” 45lb. particle board core.

Internal edgebanding: Front – 3/4” x 4” Solid Birch Sides: 3/4” x 7/8” Solid Birch Back: 3/4” x 1/8” Solid Birch

-Sides:1-1/4” Birch Veneer Plywood with 1” x 1-3/4” Solid Birch trim pieces along front and back edges. Sides also have a solid birch horizontal trim piece along the bottom of the panel

- Frames: Four sided Hardwood with glued and stapled half lap joints

- Aprons: 3/4” Birch Veneer Plywood with Birch veneer edgebanding

- Modesty Panel: 3/4” Birch Veneer Plywood

- Keyboard Tray: 3/4” Birch Veneer Plywood with solid Birch veneer edgebanding on front and sides. Front edge of keyboard tray has a 7/8” x 3” solid Birch shaped wrist rest.

- Keyboard Slides KV #8357-16” metal runners with undermount shelf tabs and hold-open feature. Tested to 50,000 cycles with a 75lb dynamic load rating.

- Runners Supports 3/4” x 4-1/4” Solid Hardwood

- Floor Glides Nylon to prevent rusting and marking of floors.

- Support Bar 3/4” x 3/4” x 30” long steel bar

CONSTRUCTION:

- Sides shall be joined using internal hardwood four-sided frames above and below the drawer, screwed to the sides. The modesty panel shall also be screwed to the sides using 3/4" x ¾” x 10” long hardwood cleats. Front aprons and hardwood runner supports are screwed to the frame structure.

The modesty panel has a wire access hole in back of the keyboard tray.

The top is secured to the top hardwood frame with screws. A 3/4” x 3/4” x 30” long steel support bar is screwed to the top for reinforcing along the front edge..

FINISH:

- Finish materials shall be of best quality to give hard durable smooth, liquid resistant finish. All surfaces exposed to view in normal use shall be smoothly machined and sanded. The application of finishing materials shall be controlled to produce items of uniform finish without sags, runs, orange peel, overspray or other defects detrimental to a smooth quality appearance. Finish shall be UV cured urethane and/or water base acrylic. Finishing process shall be environmentally friendly and emit no V.O.C.’s (Volatile Organic Compounds) into the atmosphere.

- Wild Cherry

- Dinning chair w/ Upholstered Seat

DIMENSIONS

- Back Height 34-1/2"

- Depth 19”

- Seat Height 19-1/2"

- Seat Size 18”W x 17-1/2DP”

MATERIAL

- Rear Uprights 1-1/4” x 1-1/2” Solid Wood

- Front Legs 1-1/4” x 1-1/2” Solid Wood

- Front Seat Frame Rail 3/4” x 2” Solid Wood

- Curved Seat Frame 1” x 2” Curved formed plywood

- Front Stretcher 3/4” x 3/4” Solid Wood

- Curved Stretcher 3/4” x 3/4” Curved plywood

- Top Seat Back Slat 3/4” x 3-1/8” Solid Wood (curved)

- Seat Back Slats 3/4” x 1-3/8” Solid Wood (curved)

CONSTRUCTION

- All joints are double dowelled where possible or mortised for added strength and stability. The curved plywood seat frame is bolted through the rear uprights and mortised into the front legs. The front seat frame rail is also mortised into the front legs. Solid wood corner blocks are glued and screwed into the curved plywood seat frame and the front seat frame as well as lag bolted to the front legs. A one piece curved plywood stretcher is screwed into the rear uprights and front legs. Seat back slats are fully mortised into the back posts. Upholstered seat is made of a 3/4" plywood base, a 1-1/2" layer of foam, and a fabric cover.

FINISH

- Wild Cherry

FABRIC

Absecon crypton, Suite Series 1

Width 39-1/2" X Depth 24" X Height 36"

MATERIAL:

Curved Top Plastic laminate, Wilson Art 7054-60 and balanced backer on a 3/4” 45lb. particle board core.

Internal edgebanding: Front – 3/4” x 4” Solid Birch Sides – 3/4” x 7/8” Solid Birch Back – 3/4” x 1/8” Solid Birch Sides 3/4” Birch Veneer Plywood with 1” x 1-3/4” Solid Birch trim pieces along front and back edges. Sides also have a solid birch horizontal trim piece along the bottom of the panel Frames Four sided Hardwood with glued and stapled half lap joints Back 1/4” Wild Cherry Hardboard (2 Sided) Curved Fixed Shelf Plastic laminate, Wilson Art 7054-60 and balanced backer on a 3/4” plywood core. Bullnosed edgebanding is matching PVC T-Moulding.

Adjustable Shelf Plastic laminate, Wilson Art 7054-60 and balanced backer on a 3/4” plywood core. Edgebanding is 3mm matching PVC. Bottom shall have recesses for adjustable shelf supports.

Drawer Fronts 3/4” Birch Veneer Plywood with solid Birch veneer edgebanding Drawer Sides 7/16" x 6-1/2”h x 16”dp Birch Multi-ply Drawer Back 7/16" x 6-1/2” Birch Multi-ply Drawer Bottom 1/4" Wild Cherry Hardboard Drawer Slides 16” Brown epoxy metal runners with Teflon ball bearing wheels tested to 50,000 cycles – 75lb dynamic load rating.

Floor Glides Nylon to prevent rusting and marking of floors.

Drawer Pulls 96 MM Black metal curved pull

CONSTRUCTION:

Sides shall be joined using internal four-sided frames. Frames shall be placed at the top and bottom of the case and fastened to the sides and top with screws.

Back shall be fitted into dado grooves cut along the back of the sides and securely screwed in place. Back shall have a large cut-out for routing wires and ventilation.

Top shall be butt-jointed to the sides and fastened with screws through the front and back of the upper frames. Top shall have a load capacity of 300lbs.

Drawer boxes shall be finger dovetailed at the front and back with the bottom fastened into dado grooves on the front, sides and back. Dove-tails shall be tight and well fitted. Drawer fronts shall have screw-on drawer pulls.

FINISH:

Finish materials shall be of best quality to give hard durable smooth, liquid resistant finish. All surfaces exposed to view in normal use shall be smoothly machined and sanded. The application of finishing materials shall be controlled to produce items of uniform finish without sags, runs, orange peel, overspray or other defects detrimental to a smooth quality appearance. Finish shall be UV cured urethane and/or water base acrylic. Finishing process shall be environmentally friendly and emit no V.O.C.’s (Volatile Organic Compounds) into the atmosphere.

Wild Cherry

Tops Plastic laminate, Wilson Art 7054-60 and balanced backer on a 3/4” 45 lb particle board core with matching 3mm PVC edgebanding.

Sides 3/4” Birch Veneer Plywood with solid birch veneer edgebanding.

Center Dividers 3/4” Birch Veneer Plywood with solid birch veneer edgebanding.

Backs 1/4” Wild Cherry Hardboard Frames Four sided Hardwood with glued and stapled half lap joints Base Front 3/4” Solid Birch Drawer Fronts 3/4” Birch Veneer Plywood with solid Birch veneer edgebanding Drawer Sides 7/16" x 5-1/2”h x 20”dp Birch Multi-ply Drawer Backs 7/16" x 5-1/2” Birch Multi-ply Drawer Bottoms 1/4" Wild Cherry Hardboard Drawer Slides 20” Brown epoxy metal runners with Teflon ball bearing wheels tested to 50,000 cycles – 75lb dynamic load rating.

Floor Glides Concealed casters (non-locking) Drawer Pulls 96 MM Black metal curved pull. Inserted into wood. Not to protrude out more then 1/4"

CONSTRUCTION:

Unit consists of a four drawer underbed storage unit on casters and a fixed filler box on one end. The sides of both units are constructed with four sided hardwood frames at the top and bottom, screwed to the sides.

The solid Birch base front on the drawer unit is also screwed to the sides. The back shall be fitted into dado grooves cut along the back of the sides and securely screwed in place.

Tops Shall be butt-jointed to the sides and fastened with screws through the front and back of the upper frames.

Drawer boxes shall be finger dovetailed at the front and back with the bottom fastened into dado grooves on the front, sides and back. Dove-tails shall be tight and well fitted. Drawer fronts shall have screw-on drawer pulls.

FINISH:

Finish materials shall be of best quality to give hard durable smooth, liquid resistant finish. All surfaces exposed to view in normal use shall be smoothly machined and sanded. The application of finishing materials shall be controlled to produce items of uniform finish without sags, runs, orange peel, overspray or other defects detrimental to a smooth quality appearance. Finish shall be UV cured urethane and/or water base acrylic. Finishing process shall be environmentally friendly and emit no V.O.C.’s (Volatile Organic Compounds) into the atmosphere.

Stain Color:

Wild Cherry

DIMENSIONS:

Width 68-3/4" Depth 24-1/8" Height 16-9/16"

Solid wood legs.High pressure plastic laminate on plycore for the top.

Color:

Wild Cherry Size:

30"W X 30" L X 30"H

Pillow top arms with decorative stitching on the padded headrest. Arm Height: 26", Back Height: 27". Seat Dimensions: 20w x 22d x 19h. Extended Length of Recliner when fully reclined: 72". Will Require approximately 11" of space from the wall when fully reclined. Sinuous Springs. All-steel mechanism. Kiln dried hardwood frame is double doweled, glued, and reinforced with steel at all stress points. 1.8 Poly Density Foam. Recliner can be closed hands-free. Seats and backs are heavily padded for comfort. Upholstery must holds up to more than 15,000 double rubs. Unlimited reclining positions.

Color: Java Size: W35 x D38 x H39.

42" X 24" x 30" Height

Pedestal Desk with keyboard drawer, pedestal on left side.

Solid Oak

Solid Oak

SHIPPING/HANDELING WILL BE INCLUDED IN THE UNIT PRICE.

MUST CHECK QUANTITY PER FREIGHT (Door to Door) SHIPMENT.

ALL DELIVERIES MUST BE COORDINTED WITH Mr. ADRIAN ROTH AT 00 49 631 536 0122 or

Mr. RUI SILVA AT 00 49 631 536 7578.

The Items Number: #0010, #0011, #0012 are Back Up Stock for the Furniture Series: #2200

Series: # 2200 - Grade: 01 - Solid Oak Construction with solid oak end panels and drawer fronts, and 5/8" drawer stock. Tops are matching woodgrain plastic laminate with PVC edgebanding. Drawer fronts are solid oak style #1020 double beaded with plunge pulls. Natural Finish