Attachment_3_-_PWS-ARNORTH_Physical_Security.pdf

PERFORMANCE WORK STATEMENT FOR

PHYSICAL SECURITY MAINTENANCE

1. DESCRIPTION OF SERVICES/ GENERAL INFORMATION

US Army North (ARNORTH) Fort Sam Houston has a requirement for Integrated Electronic

Security System (IESS), Access Control Systems (ACS), Alarmed Protected Distribution System

(PDS) and Closed Circuitry Television Systems (CCTV) Testing, Maintenance and Repair

Services. The contractor shall provide all resources necessary to maintain the IESS. The service contract may require expansion or modification to add additional coverage, including installation of the Security System for any new projects, sites, buildings and equipment on Fort Sam

Houston. The contractor shall provide preventive and demand maintenance, testing and repair services for US ARNORTH locations in Buildings 16, 2000, 2001, 2007, 4073, 4015, 4205, 4197, and 615 on Fort Sam Houston. The contractor shall provide all resources necessary to maintain an IESS consisting of all Access Control Systems (ACS), Closed Circuitry Television (CCTV)

Systems and Alarmed Protected Distribution Systems (PDS) and equipment as identified in the

Systems Listing of this Performance Work Statement (PWS). The contractor will replace existing proprietary equipment with hardware/software that is universal and/or non-proprietary.

Workstation and servers must be in compliance with National Security Agency (NSA) Security

Technical Implementation Guides (STIGs) as mandated by the Defense Information Systems

Agency (DISA). Additionally, management software must be certified via the Army Certificate of Networthiness (CON) process for inclusion into the Approved Products List (APL). This

PWS defines the efforts required for the testing, maintenance and replacement of ACS security system, CCTV System and PDS System components. All parts that are not covered under routine maintenance will first be approved by the Contracting Officer Representative ( COR) and provided at cost to the Government.

1.1. DESCRIPTION OF SERVICES:

1.1.1 ACS SYSTEM. The Government's ACS System includes the following: Identicard

Premisys system (Server, Controllers, and associated communication equipment), Network Data

Converters, Access Panels, Power Supplies, Interface Panels, Card Readers, Proximity Sensors, Door Strikes, Maglocks, Balanced Magnetic Sensors, Glass Break Sensors, Switches, Image

Capture Cameras, Badge Printers any other associated hardware and wiring. Contractor shall also maintain wiring from building head end blocks to the installed alarm panel, except base provided fiber. Service shall include ACS annual software backups and technical support capability via telephone.

1.1.2 ACS CONTROLS. All new or replacement card readers shall meet the Homeland Security

Presidential Directive-12, to ensure secure access to Federal Government networks and facilities by mandating the use of an interoperable secure personal identity card, there are only three cards issued that meet this requirement, the Common Access Card (CAC), Personal Identity Verification (PIV)

Credential and the Transportation Workers Identity Credential (TWIC).

1.1.3 PDS SYSTEM. The current PDS System includes the following: Alarm Processing units, Sensing Fiber, Non-Sensing Fiber, Power Supplies, Controllers, Network communication adapters and Optical Cut Off Switches and any other associated hardware and wiring. Service shall include annual calibration and telephone support plan.

1.1.4 CCTV SYSTEM. The Government's security CCTV System includes the following:

Digital Video Recorders (DVR), Network Video Recorders (NVR), Cameras, Lenses, Pan/Tilt/Zoom Mountings , Media Converters, Switchers, Multiplexers, Camera Housings, Amplifiers , AIS Viewing Software and other associated CCTV hardware and wiring.

1.1.5 SERVERS. Before the end of the base period of performance , the contractor shall upgrade/modify the proprietary IESS system (the Access Control Server & PDS Server currently in Bldg 16) so that it is compatible with Windows 10. All system software shall be DISA STIG compliant so that it can reside/interact with the US Government network. The software should appear on the approved Army products list.

1.1.6 SECURITY. Contractor employees shall have SECRET clearance prior to beginning work. The DD Form 254 Department of Defense Contract Security Classification Specification shall be completed and submitted to the COR before contract start date. The Government shall provide the contractor mechanical room keys during the course of the contract to ensure the contractors can properly support the contract during service calls, inspection etc. The contractor shall have a Law Enforcement Local Files Check completed for all employees that shall be entering Government facilities. Documentation of these checks shall be made available to the

COR upon request. Contractor employees accessing Government security systems and security plans shall have a SECRET clearance. The contractor shall provide names and social security numbers of any employee without a US SECRET security clearance that shall be entering US government facilities to the COR three days in advance. Contractor employees without a US

SECRET security clearance shall not be allowed access to any system drawings, schematics or plans . All contractor employees upon arrival at US ARNORTH Headquarters shall first check in with Visitor Access Control in Building 16 to sign in and receive access badges and shall sign out and tum in badges prior to departure. All bags and packages carried by the contractor employees shall be made available for inspection at Visitor Access Control.

1.1.7 QUALIFICATIONS. Technically qualified maintenance service personnel are required to repair and maintain the IESS. Technicians shall be qualified for execution of all on-site maintenance functions as delineated in the PWS. All contract employees shall have the appropriate license and/or certification to service or maintain equipment and software associated with this requirement.

1.1.7.1 Factory certifications are required for the contractor providing maintenance on the following major subsystems:

• Identicard IdentiPass and PremiSys ACS

• Fiber Sensys Model 208 & 348 series Fiber Defender

• Avigilon Control Center Software (ACC) and NVR

• AIS Viewer Software

1.1.7.2 In addition to the above stated certifications, the contractor shall provide employees qualified to perform electrical and electronic troubleshooting, repair, testing, diagnostics and programming of Avigilon ACC Software, Sound Masking equipment, and fiber optic communication equipment.

1.1.8. FUNCTIONAL SUPPORT. Systems preventive and demand/emergency maintenance support shall be provided and available on a 24hrs/7days a week basis as noted in the following paragraphs. All repairs shall be completed within 24 hours of contractor being notified of issue.

Contractor shall have at its disposal, 24/7 technical support for ACS and CCTV systems to resolve issues requiring advance diagnostics and guidance in restoring critical systems.

1.1.8.1 Preventive Maintenance -Contractor shall perform annual maintenance of the

ACS, PDS and CCTV Systems. Contractor shall submit a preventive maintenance schedule to the COR within 30 days of contract award. The schedule shall show all regularly scheduled preventive actions for the IESS. Preventive maintenance support shall be performed during normal duty hours. Normal duty hours shall be from 0730-

1700 hours including a one (1) hour lunch, Monday thru Friday. Preventive maintenance actions requiring downtime for systems or subsystems shall be coordinated with the

COR. Preventive maintenance actions shall be stopped should a demand maintenance requirement be reported. Preventive maintenance actions may resume following restoration of all outstanding outage tickets unless those outages attributed to Awaiting

Parts (AWP).

1.1.8.2 Demand Maintenance - Contractor shall provide local contact numbers for notification of demand/emergency maintenance requirements. Demand maintenance requirements shall take precedence over preventive maintenance requirements. Response time for demand maintenance shall be as follows:

• Critical Outage - 4 Hours response upon receipt of outage notification -

Critical system or subsystem failure resulting in major loss of ACS Server.

• Priority Outage - 12 Hours response upon receipt of Notification -Loss of system or subsystems resulting in loss of ACS and/or CCTV coverage or reporting affecting one or more of the below listed items:

• Partial loss of operator functionality at the monitoring console that does not create a critical loss of ACS capability.

• Loss of All CCTV monitoring capabilities .

• Routine Outage -24 Hours response upon receipt of Notification -Loss of any system, subsystem, or component that results in the loss or degradation of function that does not meet the criteria for Critical or Priority outages as noted above.

• System/Subsystem/Component Restoration: Contractor shall take all necessary steps within the bounds of the maintenance contract to restore any system problem as soon as possible. In the absence of specific spare equipment items, the Government's COR will be contacted and advised of the AWP status. The procurement of the required part(s) and/or repair of Government defective items, return of items under warranty, and other related expenses shall be accomplished by contractor when such costs are funded by the

Government. Priorities of all such actions shall be assigned by the COR.

1.1.9 EQUIPMENT SUPPORT. The contractor shall provide all transportation requirements for responding and attending to contract related issues. The contractor shall provide all hand tools, ladders, power tools, test equipment (less identified Government Furnished Equipment

( GFE), and expendable supplies for its operations. The contractor shall provide fiber fusion and test equipment. The contractor shall provide lifts, cranes, and other suitable platforms for elevated work involving cameras, towers, etc. The Government shall provide the contractor with all electrical power and other on-site utilities to support this contract (does not include off-site support).

1.1.10 SYSTEM INVENTORY CONTROL. Upon completion of a system inventory jointly conducted by contractor and the COR or designated Government Representative, the IESS systems inventory shall be managed by contractor for the period of performance of the requirement. System Inventory shall not interfere with operations of ARNORTH facilities for no more than 6 hours a month. The following functions shall be performed as part of the inventory control requirement:

1.1.10.1 Conduct initial inventory with COR within 5 working days of site mobilization.

Establish and maintain an active database of all accountable equipment which shows the following:

• Item description/Name

• Current location and/or assignment (IE: Bldg 4168 Locker 12)

• Operational status (active, functional spare, defective-factory maintenance , defective-not economically repairable, AWP, awaiting maintenance , missing , surplus)

• Make, model, serial # (if applicable)

• Major Assembly ID (identifies any major assembly for which this item is a part)

• New-Placed in Service Date (this is purchase/install date when item is new)

1.1.11 DATA BASE MAINTENANCE. Establish and maintain a maintenance database that links inventory data with maintenance data and tracks the following information for all performed maintenance:

• Preventive maintenance dates for each accountable item or major assembly.

• Preventive maintenance findings/adjustments for each accountable item.

• Demand/Emergency Maintenance Actions

• Trouble Ticket # (Assigned by Contractor)

• Major Assembly ID

• Item Control #

• Date/Time Discovered

• Date/Time Technician Notified

• Government Rep or Contractor's name/rank/position making notification

• Method of Notification (phone, in person, email, other)

• Date/Time Technician on site

• Description of Trouble

• Point of Contact and telephone # for field location troubles requiring access to remote secure buildings or locations

• Description of troubles found

• Description of restoration actions (time line format to include AWP periods)

• Date/time restored

• Date/time Government notified of restoration

• Person notified of restoration (Name/Rank/Position)

• Technician Name completing repairs

1.1.12 MAINTENANCE REPORTING. The contractor shall submit a monthly status report

(7th of every month) to the COR that shall included a summary of all preventive and demand maintenance actions, any outstanding maintenance issues to include outages pending receipt of parts or awaiting maintenance , and a general statement as to the general health of the IESS.

Outage reports shall be processed and documented on an approved maintenance ticket and signed by the Maintenance Technician making the repairs. A completed copy of each closed outage ticket shall be forwarded to the COR upon completion of the work and a file copy maintained by the contractor.

1.1.13 EXCLUSION. Communication infrastructure is not considered part of the Channel

Asociated Signaling (CAS) telephone and fiber backbones .When communication failures are suspected within the CAS 's communication infrastructure , Contractor shall advise the COR and a work order shall be secured to correct the problem . The line of demarcation between IESS and Fort Sam Houston communications infrastructure shall be at the CAS 's fiber patch or telephone punch blocks in each building. Fiber and cabling installed and documented as a dedicated part of the IESS (not common carrier facilities) is not part of this exclusion.

1.1.14 AIR FORCE ANTITERRORISM (AT) PROGRAM. The AT program seeks to deter or limit the effects of terrorist acts against the Air Force (AF) by giving guidance on collecting and disseminating timely threat information, providing training to all AF members, developing comprehensive plans to deter and counter terrorist incidents, allocating funds and personnel and implementing AT measures. In accordance with AFI 10-245 paragraphs 2.17 and paragraph 2.25, DOD contractors and sub-contracts personnel shall be offered Level 1 -

AT Awareness Training. Compliance with the training shall be monitored by the COR.

2. SERVICE SUMMARY

PERFORMANCE

OBJECTIVE

PWS

REFERENCE

PERFORMANCE

THRESHOLD

Equipment shall be fully operational 24 hours a day, seven

(7) days a week.

1.1.8 90%

Repairs and corrective actions shall be completed within 24 hours of contractor being notified.

1.1.8 90%

System Inventory shall not interfere with operations of ARNORTH facilities for no more than six (6) hours a month.

1.1.10 90%

Conduct annual inspection of all system equipment.

1.1.8 90%

The contractor shall submit a monthly status report (7th of every month) to the COR.

1.1.12 90%

The contractor shall respond to

Critical Outages within 4 hours and Priority Outages within 12 hours of being notified of issue.

1.1.8 90%

3. GOVERNMENT FURNISHED PROPERTY

Mechanic Room Keys

4. APPENDIX

A. CURRENTLY INSTALLED EQUIPMENT BY BUILDINGS

B. ACRONYMS

APPENDIX A

CURRENTLY INSTALLED EQUIPMENT BY BUILDINGS:

Building 16 Camera, IDS and Recording Equipment

Qty Manufacturer P/N Description

1 Identicard F59-LT/IPASS Identipass LT to Identipass 2.0 upgrade Software

8 Identicard F55-9CTLR/6 9000 4 Door Controller 6000 card capacity

1 Identicard F55-92RDR/6 9000 2 Door Controller (Not Exp)

6 Identicard F55-RDR/EXPD 9000 4 Door Expansion Card

3 Identicard F55-RIO/BRD 9000 Remote 1/0 Card I 6IN 160UT

46 HID HID-R10 iclass Proximity Reader

10 HID HID-RK40-6130 iclass Proximity Reader/Keypad

Detection

Systems DS160 Request to Exit Motion Detector

2 Locknetics 390PWM-DSM Mag Lock 1200 LB low current W/status

42 Locknetics 390TJ/DSM/MBS/PWM

Mag Lock 1200 LB Door sensor, Top of Jam Power

Miser

3 Locknetics 405-ARSB PowerBolt right angle electrified deadbolt .9A at 12vdc

29 STI SS-2105X RTE Green Momentary Button

2 Von Duprin 6211FSE Fail Secure Electric Strike for Cylindrical locks

1 Von Duprin 621OFSE Fail Secure Electric Strike

4 Locknetics 510-EIR Locknetics 12V 3AH Power Supply W/ relay

3 Locknetics SBE Standby Battery Enclosure

28 Yuasa NP4-12 12 VDC 4 Amp Battery

17 Sentrol 2505A-L Magnetic Contact Switch w/ Armored Cable

17 System Sensor MP-PA400W Sonic Alert Sounder 12/24VDC

2 Sentrol 1078C-M Door Status Switch Recessed 3/4" Brown

1 Altronix SMP3 12V 2.5A Power Supply board only

1 Altronix TP1640 16v 40 VA Transformer for SMP3E

1 NiceVision NVA-V9-BAS-32 NiceVision Alto basic recorder

2 NiceVision

NVA-V9-4CIFPLUS-

RT-16

Video Recording software supporting 16 cameras (1

VICO)

4 NiceVision NVA-V9-0LS-HDD250 250GB of storage

1 NiceVision

NVR-ENT-SVR9420-

RIN5-6TB

9400 Enterprise system, 2U, with Internal Hot Swappable

Raid-5 (5+1), total of 5TB (including SML)

6 NiceVision NV-ENT-I CH

Single license for NiceVision Enterprise package video channel

1 NiceVision NV-MEDIA PACK

Media pack including application software and documentation channel.

1 NiceVision 092910SC01 NET 2.0 software upgrade

Transition

Networks MIL-SM4004TG

(4)10/100/ 1000 BASE-T Ports & (4) SFP IOOOBASE-

X Ports

Transition

Networks TN-SFP-LXl

Hot Swap SFP SM LX Optical Transceiver 1000 Base-

LX (6.2 Mile)

1 AIS Remote Viewer Remote Camera Viewing Software.

1 Visionman V133-3304

Pentium D 930 3.0Ghz I Dual-Core 1U Hotswap Rackmt

Server

1 Visionman VI 33-3122 Intel Pentium 4 2.8GHz I 1U Rackmount Server

2 Microsoft

Win XP Pro OEM Microsoft® Windows® XP Pro, OEM

Preload

2 AIS KBD-MOUSE PC 104 Keyboard & Optical Mouse Kit

1 Blackbox AC643A Keyboard/Mouse Extender Local Unit

1 Blackbox AC644A Keyboard/Mouse Extender Remote Unit

1 ConnectGear GS-S16RE 16-Port 10/ 100 Rackmount Switch

1 Blackbox ST-CSKVM-600 Keyboard Video and Mouse Extender over Cat 5

1 Fiber Options S732DVT-EST1 Video and 2 way Multi Protocol Data Transmitter Wall Mt

1 Fiber Options S732DVR-RST1 Video and 2 way Multi Protocol Data Rcvr Rack Mt

2 Fiber Options S704VR-EST 4 Channel Video Receiver Wall

2 Fiber Options S704VR-RST 4 Channel Video Receiver Rack Mount

1 Fiber Options S700VT-TST

Cam Video XMTR, Ultra Compact Tubular, Multi Mode, 850nm

1 Fiber Options MM, Rack, 850nm

3 Fiber Options 613P Power Supply 13.5 VDC 1.3 Amp

13 Everfocus EQ500 1/3" Hi-Res Day/Night Camera 480 lines.

13 Tamron 13VG550-SQ

Lens, 1/3, Varifocal, 5-50mm,-Fl.4, DC Type, CSMount, 4-Pin

8 Samsung GVHOU3512 Environmental Housing with Mounting Arm.

5 Videolarm LCH Environmental Housing with Mounting Anrm.

1 Everfocus EVE-EHD350/N-1 Vandal Resistant 3.6-8MM Color Camera 480 lines

4 Altronix ALTV-244 4 Camera Power Supply

2 Unknown XP2440 Plug In Transformer For Camera

3 AD ADCHMTPOLE Camera Housing Pole Mount.

1 AIS SM-SC/LX-2M DPX 6' SM Fiber Patch Cord SC -LX Duplex

7 AIS MM-ST/ST-2M MM Fiber Patch Cord ST-ST 2 Meter

1 AIS 242010N4 24x20x10 Enclosure Nema 4 enclosure W/backplane

1 Hoffman CPMK12 Pole Mounting Kit for Enclosure

Building 16 PDS Equipment

Qty Manufacturer P/N Description

1 Identicard F55-IPASSPAR Identipass Partitioning

1 Identicard F55-IPASSUPOST Identipass User Interface (After ini Install) 1 or 2 Client

1 AIS AAA-ENS Automatic Alarm Email Notification Service

2 Identicard F55-9CTLR/6 9000 4 Door Controller 6000 card capacity

2 Identicard F55-RIO/BRD 9000 Remote I/O Card 16IN 160UT

3 Fiber Sensys RK-200 (RK-208) Rack W. Power Supply For 208R 208E/N

24 Fiber Sensys FD-208R 208 With Rack Mounting

21 Fiber Sensys SCS-2000-2x2 Optical Disconnect Switch 2 fiber in 2 fiber out

2 Fiber Sensys RK-210 19-inch Rack for Optical Cutoff Switch

Building 4205 Camera and Recording Equipment

1 NiceVision NVA-V9-BAS-16 Alto basic recorder, supporting 16 cameras

1 NiceVision

NVA-V9-4CIFPLUS-

RT-16

Video Recording software supporting 16 cameras (1

VICO)

3 NiceVision

NVA-V9-0LS-

HDD250 250GB of storage

2 Milan

E-1OOBTX-FX-

05(SM)

Fast Ethernet Media Converter 1OOBaseTX-1 OOBaseFX

SM SC

8 Everfocus EQ500 1/3" Hi-Res Day/Night Camera 480 lines.

8 Tamron 13VG550-SQ

Lens, 1/3, Varifocal, 5-50mm,-Fl.4, DC Type, CSMount, 4-

Pin S

8 Videolarm LCH Environmental Housing with Mounting Arm.

1 Altronix ALTV-248 8 Camera Power Supply

THE FOLLOWING BUILDINGS WILL NEED TO HAVE SECURITY MEASURES ADDED

THAT MATCH THE CAPABILITIES OF THE BUILDINGS LISTED ABOVE.

Building 2000 Access Control Equipment

5 Identicard PREM-CTLR2RDR PremiSys IP Controller with Two-Reader ports

17 Identicard PREM-BRD2RDR PremiSys Two-Reader Board

4 Identicard PREM-ENCLG PremiSys Large Enclosure

4 Identicard PREM-TAMPER PremiSys Tamper

4 Identicard PREM-ENCLOCK PremiSys Enclosure Lock and Key

9 Altronix AL1024ULACM Power Supply-Charger, 24 VDC @ 8 Amp Fire / Access

Interface

9 AlarmSaf BC-100 AlarmSaf Enclosure 16 x 12 x 7

41 Identicard HID-6120CGN0408-

G3.0 R40 Iclass Reader gray, FIPS 64 bit, back box mount

48 AIS TX-LOCK-SCHLAGE Provide and install (48) 672-36-313 and (48) 9507-18B

38 UTC RCR-REX-W Request To Exit Dual Tech Sensor, White

20 UBC UBC-D5744 12 VDC 12 Amp Battery

18 UBC UPG-UB12350 12 VDC 35 Amp Battery

2 IFS GE-DS-82 8-Port 10/100+2 GigE TP/SFP Managed Switch

2 IFS SFP1000LX-10KM 1000 Base-LX SFP Module - (single-mode) 10km

1 Commscope UNP610-24P 24 Port Cat 6 patch Panel 110 style

Building 2000 PDS Equipment

1 Identicard PREM-CTLR1POE PremiSys POE Controller with One Reader port

1 Identicard PREM-BRDIN PremiSys 16 Input Board

1 Identicard PREM-BRDOUT PremiSys 16 Relay Output Board

1 Identicard PREM-PS10A Ten-Amp Power Supply

1 Identicard PREM-ENCLG PremiSys Large Enclosure

1 Identicard PREM-ENCLOCK PremiSys Enclosure Lock and Key

2 Identicard PREM-TAMPER PremiSys Tamper

12 Fiber Sensys 980-22895 FD-348R Rack-Mounted Alarm Processing Unit.

2 Fiber Sensys 980-52920 RK-348 Rack W. Power Supply For 208R and 348 APU's Holds up to 8 APU

7 Fiber Sensys 980-71437 SCS-2X2-SM-SC Optical Cutoff Switch 2x2 Singlemode with

SC Connectors

1 Fiber Sensys 980-61447 RK-210 19-inch Rack for Optical Cutoff Switch

6 AIS PDS ZN-Kit PDS Installation kit for Zone Box

84 AIS PDS STA-Kit PDS Installation kit for Station Box

1 Winsted 97020 15-3/4"H Sectional Wall Mount Cabinet

Building 2001 Access and IDS Equipment

1 Identicard FPO150-D8PE4M1 LifeSafety Up-to-20 Door Single Voltage Integrated Power

System.

1 Identicard PREM-CTLRIP PremiSys IP Controller

1 Identicard PREM-CTLR2RDR PremiSys IP Controller with Two-Reader ports

1 Identicard PREM-BRDIN PremiSys 16 Input Board

1 HID 921NHRNEG00073 RK40-H PIV- iClass Reader/Keypad, Iclass, FIPS 64 Bit

Reader Grey, Single Gang Mount

1 HES 9600-12/24-630-LBSM HES Electric Strike, Genesis, DualLocking, LBMS Option, 630 Satin, Surface Mounted, 12 VDC Or 24 VAC

5 Allegion AD-301-993R-70-

FMK-RHO-625-PD

S123-LHR

AD 301 Electric Lock, Exit Trim Rim, Classroom Function, Smart Card FIPS

2 Allegion AD-301-993S-70-

FMK-RHO-625-PD

S123-RHR-

AD 301 Electric Lock, Exit Trim Surface Vert Rod, Classroom Function, Smart Card FIPS

1 HES 9600-12/24-630-LBSM HES Electric Strike, Genesis, DualLocking, LBMS Option, 630 Satin, Surface Mounted, 12 VDC Or 24 VAC

1 UTC RCR-REX-W Request To Exit Dual Tech Sensor, White

1 Inovonics EN4232MR 32 Channel Receiver 12 Output Relay (1Tbl, 11 Alarm)

8 Inovonics EN1210W Door /Window Transmitter

Building 2007 Access Equipment

1 Identicard FPO150-D8PE4M1 LifeSafety Up-to-20 Door Single Voltage Integrated Power

System. Supplies 12V/12A or 24V/6A to power eight boards that mount on the cabinet door and on a removable backplate.

Eight Class 2, Power Limited (CL2PL) outputs (D8P board) for independent power connection to each board and auxiliary equipment. Battery space for 12V, 8Ah battery.

Cabinet size: 24" x 20" x 4.5"

1 Identicard PREM-CTLRIP PremiSys IP Controller

1 Identicard PREM-CTLR2RDR PremiSys IP Controller with Two-Reader ports

1 HID 921NHRNEG00073 RK40-H PIV- iClass Reader/Keypad, Iclass, FIPS 64 Bit

Reader Grey, Single Gang Mount

1 HES 9600-12/24-630-LBSM HES Electric Strike, Genesis, DualLocking, LBMS Option, 630 Satin, Surface Mounted, 12 VDC Or 24 VAC

4 Allegion AD-301-993R-70-

FMK-RHO-625-PD

S123-LHR

AD 301 Electric Lock, Exit Trim Rim, Classroom Function, Smart Card FIPS

1 Allegion AD-301-993S-70-

FMK-RHO-625-PD

S123-RHR-

AD 301 Electric Lock, Exit Trim Surface Vert Rod, Classroom Function, Smart Card FIPS

1 HES 9600-12/24-630-LBSM HES Electric Strike, Genesis, DualLocking, LBMS Option, 630 Satin, Surface Mounted, 12 VDC Or 24 VAC

1 UTC RCR-REX-W Request To Exit Dual Tech Sensor, White

Building 4073 Access Equipment

1 Identicard FPO150-D8PE4M1 LifeSafety Up-to-20 Door Single Voltage Integrated Power

System.

1 Identicard PREM-CTLR2RDR PremiSys IP Controller with Two-Reader ports

2 Identicard PREM-BRD2RDR PremiSys Two-Reader Board

4 HID 921NHRNEG00073 RK40-H PIV- iClass Reader/Keypad, Iclass, FIPS 64 Bit

Reader Grey, Single Gang Mount

1 HID 920NHRNEG0001T R40-H PIV- iClass Reader, FIPS 64 Bit Reader Grey, Single

Gang Mount

4 UTC RCR-REX-W Request To Exit Dual Tech Sensor, White

4 STI SS-21A9EX Emergency Exit button. Latching button with turn to reset and built in sounder cover

1 U.S.P HUB-2SA Surface mount Switch Momentary DPDT screw terminal

5 Dynalock 3000-DSM-LP Mag Lock 1500 LB W/status and Low Current

1 Trine 4850-POE-32D-LB Rim Strike 1/2" Surface mounted 12VDC with Latchbolt

Monitor for Rim Panic Devices

1 GRI 2020-T-W 3/8 Recessed Door Status Switch White with Terminals

Building 4073 PDS Equipment

1 Identicard PREM-PCLIENT13 Premisys Pro Client Licenses. 1 - 3 Concurrent Client

Connections. Price is per Client.

1 Identicard PREM-CTLR2RDR PremiSys IP Controller with Two-Reader ports

1 Identicard PREM-LS75F Four to eight Door Single Voltage Integrated Power Supply.

Supplies 12V/6A or 24V/3A to power devices 24x20x4.5

2 Fiber Sensys 980-22895 FD-348R Rack-Mounted Alarm Processing Unit. 8 APUs can be installed in the 980-52920 RK-208/348 Rack.

Communication options include: RS-232, RJ-45 for IP/XML or Fiber Security Network (FSN). Output: 100mA DC

Normally-Open and Normally-Closed Relay Contacts.

1 Fiber Sensys 980-52920 RK-348 Rack W. Power Supply For 208R and 348 APU's

Holds up to 8 APU

1 Fiber Sensys 980-61447 RK-210 19-inch Rack for Optical Cutoff Switch

2 Fiber Sensys 980-71437 SCS-2X2-SM-SC Optical Cutoff Switch 2x2 Singlemode with SC Connectors

1 AIS AIS-PK1 Panel Installation Kit

2 AIS PDS ZN-Kit PDS Installation kit for Zone Box

19 AIS PDS STA-Kit PDS Installation kit for Station Box

1 UBC UBC-D5743 12 VDC 8 Amp Battery

Building 4015 Access Equipment

1 Identicard FPO150-D8PE4M1 LifeSafety Up-to-20 Door Single Voltage Integrated Power

System.

1 Identicard PREM-CTLRIP PremiSys IP Controller

1 Identicard PREM-CTLR2RDR PremiSys IP Controller with Two-Reader ports

1 HID 921NHRNEG00073 RK40-H PIV- iClass Reader/Keypad, Iclass, FIPS 64 Bit

Reader Grey, Single Gang Mount

1 HES 9600-12/24-630-LBSM HES Electric Strike, Genesis, DualLocking, LBMS Option, 630 Satin, Surface Mounted, 12 VDC Or 24 VAC

1 Allegion AD-301-993R-70-

FMK-RHO-625-PD

S123-LHR

AD 301 Electric Lock, Exit Trim Rim, Classroom Function, Smart Card FIPS

3 Allegion AD-301-993S-70-

FMK-RHO-625-PD

S123-RHR-

AD 301 Electric Lock, Exit Trim Surface Vert Rod, Classroom Function, Smart Card FIPS

1 HES 9600-12/24-630-LBSM HES Electric Strike, Genesis, DualLocking, LBMS Option, 630 Satin, Surface Mounted, 12 VDC Or 24 VAC

1 UTC RCR-REX-W Request To Exit Dual Tech Sensor, White

Building 615 Access and IDS Equipment

1 Identicard FPO150-D8PE4M1 LifeSafety Up-to-20 Door Single Voltage Integrated Power

System.

1 Identicard PREM-CTLRIP PremiSys IP Controller

1 Identicard PREM-CTLR2RDR PremiSys IP Controller with Two-Reader ports

1 Identicard PREM-BRDIN PremiSys 16 Input Board

1 HID 921NHRNEG00073 RK40-H PIV- iClass Reader/Keypad, Iclass, FIPS 64 Bit

Reader Grey, Single Gang Mount

1 HES 9600-12/24-630-LBSM HES Electric Strike, Genesis, DualLocking, LBMS Option, 630 Satin, Surface Mounted, 12 VDC Or 24 VAC

5 Allegion AD-301-993R-70-

FMK-RHO-625-PD

S123-LHR

AD 301 Electric Lock, Exit Trim Rim, Classroom Function, Smart Card FIPS

2 Allegion AD-301-993S-70-FMK-

RHO-625-PD S123-

RHR-

AD 301 Electric Lock, Exit Trim Surface Vert Rod, Classroom Function, Smart Card FIPS

1 HES 9600-12/24-630-LBSM HES Electric Strike, Genesis, DualLocking, LBMS Option, 630 Satin, Surface Mounted, 12 VDC Or 24 VAC

1 UTC RCR-REX-W Request To Exit Dual Tech Sensor, White

1 Inovonics EN4232MR 32 Channel Receiver 12 Output Relay (1Tbl, 11 Alarm)

8 Inovonics EN1210W Door /Window Transmitter

Building 4197 Access Equipment

1 Identicard FPO150-D8PE4M1 LifeSafety Up-to-20 Door Single Voltage Integrated Power

System.

1 Identicard PREM-CTLR2RDR PremiSys IP Controller with Two-Reader ports

2 Identicard PREM-BRD2RDR PremiSys Two-Reader Board

4 HID 921NHRNEG00073 RK40-H PIV- iClass Reader/Keypad, Iclass, FIPS 64 Bit

Reader Grey, Single Gang Mount

1 HID 920NHRNEG0001T R40-H PIV- iClass Reader, FIPS 64 Bit Reader Grey, Single

Gang Mount

4 UTC RCR-REX-W Request To Exit Dual Tech Sensor, White

4 STI SS-21A9EX Emergency Exit button. Latching button with turn to reset and built in sounder cover

1 U.S.P HUB-2SA Surface mount Switch Momentary DPDT screw terminal

5 Dynalock 3000-DSM-LP Mag Lock 1500 LB W/status and Low Current

1 Trine 4850-POE-32D-LB Rim Strike 1/2" Surface mounted 12VDC with Latchbolt

Monitor for Rim Panic Devices

1 GRI 2020-T-W 3/8 Recessed Door Status Switch White with Terminals

APPENDIX B

ACRONYMS:

ARNORTH Army North

IESS Integrated Electronic Security System

ACS Access Control Systems

PDS Protected Distribution System

CCTV Closed Circuitry Television Services

PWS Performance Work Statement

NSA National Security Agency

STIGS Security Technical Implementation Guides

DISA Defense Information Systems Agency

CON Certificate of Networthiness

APL Approved Products List

COR Contracting Officer Representative

CAC Common Access Card

PIV Personal Identity Verication

TWIC Transportation Workers Identity Credential

DVR Digital Video Recorder

NVR Network Video Recorder

ACC Avigilon Contro Center

AWP Awaiting Parts

GFE Government Furnished Equipment

CAS Channel Associated Signaling

AT Antiterrorism

AF Air Force