Exhibit A-E Combined - Post(PDF).pdf

1 | P a g e

Exhibit A

Unit #1528 2014 Ford E450 158-inch Chassis

ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

1 Remount of and Cutaway Van Ambulance (type III)

2024 or newer, Van Cutaway Chassis, largest Gas Engine available, 158"WB. Must meet or exceed all GVWR ambulance standards as specified in CAAS

3.0

Mount three (3) unit designator placard holders on unit; Curbside, rear and streetside. Position of holders to be provided upon prebuild meeting. Exact model/brand of holders will be provided by customer.

4 OEM High Idle Controls

5 Anti-Theft, Sound Off Signal ETISSO Ignition Security Systems

6 Back up Camera Monitor- Remove and Transfer for Existing Unit. Test and confirm functionality

Floor Cab Console, Custom Type III w/2 Cupholders, Large Map Slot and FWD Flat Section for Computer

Bracket. Console shall be coated with spray “bed liner” type coating

8 Stealth Switch, Cab/Mod Unlock Switch, Cab Grille

9 Running Boards, Grip Strut, Pair

Aluminum “Alcoa Style” wheels front and outside rear with Steel mounted on the inside rear. Rear wheels shall be separated by approved “barrier”, separating unlike metals.

Heat/AC – Replace existing HVAC unit. Replacement should be dual input AC/DC and shall be “Hoseline” brand or similar style unit.

Replace rear bumper. Any replacement components shall be with material and style that matches or exceeds the existing bumper

13 Black Undercoating, Rear Bumper Supports

Non-Emergency ‘Scene’ Lights – Reuse Existing Lights where able. If unable to reuse any existing lights, replace with same brand/style. Any changes will need to be approved by Rowan EMS prior to installation. Any replacement Flanges required should be Whelen 700 to fit existing lighting, chrome

Emergency Lighting – Reuse Existing Lights where able. If unable to reuse any existing lights, replace with same style. Any changes will need to be approved by Rowan EMS prior to installation. Any replacement Flanges required should be Whelen 900 to fit existing lighting, chrome

2 | P a g e

Unit #1528 Continued

ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

16 Inspect siren speakers, if replacement is required, must be dual Federal Signal, 100 Watts, in bumper

17 Inspect / replace as needed lighting Flanges, Whelen Chrome to match existing

18 Module Interior - Clean & Inspect

Paint – Exterior of module shall be completely inspected. Any scratches and required body work shall be repaired and repainted to a color (white) matching chassis and original module color. Any exterior graphics removed shall be replaced with customer supplied design. (change from existing)

20 Transfer Lights Whelen TIR6 500 LED, Red/Clear – Front Grille. Replace as needed

Graphics, module area. Exact colors and graphics to be determined during prebuild. Any decals removed during body repair shall be replaced and shall match original decals. If entire graphics from box are removed, customer shall supply design on new, replacement graphics

Transfer and install radio from existing chassis to new chassis. Radio must be fully functional upon remount completion.

Remove Kenwood brand radio and return along with all loose, associated components. Any space created from removed radio shall be patched with professional style components.

Clean/Inspect existing console. Replace only as needed. If replacement is warranted, switch location, radio location and computer mounting should mirror existing console. Repair/cover existing hole in console. Repair work should be professional in nature with like/same materials as existing console

25 Repair any minor body work on exterior sides of Module

Grille Guard and Replacement reinforced Bumper which meets or exceeds Manufacturer Specifications (Bull Bars will not be accepted) All Siren Speakers

(named above) and air horns shall be mounted within bumper unless approved otherwise. Grill guard must

NOT prohibit forward facing emergency lighting

There shall be provided a Stryker® cot system installed. The system will consist of the following: The newest version of the below described:

Stryker® Power Pro 2 Cot (with XPS), M/N 6507-

000000 Stryker® Power Load System, M/N 6390-000000

28 Estimated Build Time from award of Bid

29 Inspect/replace as needed all grabrails located throughout module

3 | P a g e

ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

30 Inspect/replace as needed all existing rub rails with same as existing

31 Install ground clearance lighting, wired to illuminate upon opening of any exterior doors.

Inspect / replace as needed Inverter with pure sine wave inverter commensurate with existing capacity or larger.

33 Inspect / replace aluminum fuel filler cap housing.

Repair any bodywork if modifications are needed

34 Inspect and/or replace as needed any aluminum “Diamond Plate” on exterior of module

35 Replace existing “door grabbers” on rear module door. Each door shall have two (2) grabbers

36 Inspect / replace as needed all door latches and associated connecting rods and/or cables

Inspect/replace as needed interior Captains Seat with four (4) point restraining seat. Must be of integral child seat style

Test / replace as needed interior module electrical switches. Any replacements shall be of same style as existing switches

Inspect all module compartmentation Lexan doors.

Replace any found to be cracked or broken with same style as existing.

40 Inspect bench seat padding and vinyl. Recover as needed.

41 Install two (2) new portable O2 brackets; location to be determined.

Install one (1) SIERRA MG90 5G AIRLINK 5G Airlink wireless gateway, provided by the dealer or manufacturer. The MG90 5G shall be installed in the cabinet containin existing gaeway and shall be powered by the unswitched 12v, +/- 15-amp circuit that is connected to the isolated third battery. Any devices removed shall be returned to customer.

43 Replace all exterior module door gaskets with new, watertight gaskets

44 Install Aeroclave connection port. Exact locations and specifics to be provided during prebuild meeting

45 Install “Grover” style airhorns with trumpet located as noted above.

Replace all seatbelts throughout module. All seatbelts should be red in color and meet or exceed all current SAE Automotive and CAAS 3.0 standards. Seatbelt and anchorages must meet or exceed Motor Vehicle Seat Belt Anchorages - Performance Requirements, Seat Belt Hardware Performance Requirements (STABILIZED Jul 2022) J141_202207

47 Inspect / replace as needed lighting Flanges, Whelen Chrome to match existing

4 | P a g e

ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

Inspect / replace rear Tow Hook surround mounting brackets with same or similar style as existing brackets as needed

49 Replace ‘Anti-Slip’ tape on the floor at all entry points;

side and rear

Replace all AC electrical connections and covers on exterior of module. Install new plastic “engraved” placard labeling of AC outlets

Completely inspect all ‘rub-rails’ along bottom of module. Any replacements shall be of same style as existing rub-rails

Replace both electrical shoreline covers. Inspect and replace as needed all connecting receptacles, verifying all wiring is connected and functioning properly to meet CAAS 3.0 and UL requirements.

Install new plastic “engraved” placard labeling of AC outlets

Install Knox brand KnoxLock MedVault 2.75, Large, eKEY Override, STD Door with Wi-Fi, Surface Mount.

Exact location to be determined upon prebuild

Replace OEM mirrors with Velvac brand aftermarket mirrors. Mirrors should have same functionality as existing, OEM mirrors.

All freight cost must be reflected including transport of existing unit, return of existing chassis and any freight costs for the new completed unit.

56 Test entire Oxygen delivery system. Repair any leaks or damaged potions of integral hose(s).

57 Replace all ‘Anti-Skid’ tape and all entrances and exits of module

58 Inspect and replace any missing drip rails on module

Exhibit B

Unit #1529 2014 Ford E450 158-inch Chassis

1 Remount of and Cutaway Van Ambulance (type III)

2023 or newer, Van Cutaway Chassis, largest Gas Engine available, 158"WB. Must meet or exceed all

3 OEM High Idle Controls

4 Anti-Theft, Sound Off Signal ETISSO Ignition Security Systems

5 Back up Camera Monitor- Remove and Transfer for Existing Unit. Test and confirm functionality

Floor Cab Console, Custom Type III w/2 Cupholders, Large Map Slot and FWD Flat Section for Computer

7 Stealth Switch, Cab/Mod Unlock Switch, Cab Grille

8 Running Boards, Grip Strut, Pair

Aluminum “Alcoa Style” wheels front and outside rear with Steel mounted on the inside rear. Rear wheels

12 Black Undercoating, Rear Bumper Supports

Non-Emergency ‘Scene’ Lights – Reuse Existing Lights where able. If unable to reuse any existing lights, replace with same brand/style. Any changes will need to be approved by Rowan EMS prior to able. If unable to reuse any existing lights, replace with same style. Any changes will need to be approved by Rowan EMS prior to installation. Any

15 Inspect siren speakers, if replacement is required, must be Dual Federal Signal, 100 Watts, In Bumper

16 Inspect / replace as needed lighting Flanges, Whelen

Unit #1529 Continued

ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

17 Module Interior - Clean & Inspect

Paint – Exterior of module shall be completely inspected. Any scratches and required body work shall be repaired and repainted to a color (white) matching chassis and original module color. Any

19 Transfer Lights Whelen TIR6 500 LED, Red/Clear –

Graphics, module area. Exact colors and graphics to be determined during prebuild. Any decals removed during body repair shall be replaced and shall match original decals. If entire graphics from box are

22 Repair any minor body work on sides of Module

Clean/Inspect existing console. Replace only as needed. If replacement is warranted, switch location, radio location and computer mounting should mirror existing console. Repair/cover existing hole in

Grille Guard and Replacement reinforced Bumper which meets or exceeds Manufacturer Specifications (Bull Bars will not be accepted) All Siren Speakers

(named above) and air horns shall be mounted within

There shall be provided a Stryker® cot system installed. The system will consist of the following: The newest version of the below described:

Stryker® Power Pro 2 Cot (with XPS), M/N 6507-

000000 Stryker® Power Load System, M/N 6390-000000

27 Inspect and replace any missing drip rails on module

29 Inspect/replace as needed all grabrails located throughout module

Replace all AC electrical connections and covers on

ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

31 Inspect/replace as needed all existing rub rails with same as existing

32 Install ground clearance lighting, wired to illuminate upon opening of any exterior doors.

Inspect / replace as needed Inverter with pure sine

34 Inspect / replace aluminum fuel filler cap housing.

35 Inspect and/or replace as needed any aluminum “Diamond Plate” on exterior of module

36 Replace existing “door grabbers” on rear module door. Each door shall have two (2) grabbers

37 Inspect / replace as needed all door latches and associated connecting rods and/or cables

Inspect/replace as needed interior Captains Seat with

42 Inspect bench seat padding and vinyl. Recover as

43 Install two (2) new portable O2 brackets; location to be determined.

Install one (1) SIERRA MG90 5G AIRLINK 5G Airlink wireless gateway, provided by the dealer or manufacturer. The MG90 5G shall be installed in the cabinet containin existing gaeway and shall be powered by the unswitched 12v, +/- 15-amp circuit

45 Replace all exterior module door gaskets with new, 46 Install Aeroclave connection port. Exact locations and specifics to be provided during prebuild meeting

47 Replace ‘Anti-Slip’ tape on the floor at all entry points;

side and rear

48 Install “Grover” style airhorns with trumpet located as noted above.

Replace OEM mirrors with Velvac brand aftermarket

ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

Replace all seatbelts throughout module. All seatbelts should be red in color and meet or exceed all current SAE Automotive and CAAS 3.0 standards. Seatbelt and anchorages must meet or exceed Motor Vehicle Seat Belt Anchorages - Performance Requirements, 51 Test entire Oxygen delivery system. Repair any leaks

52 Replace all ‘Anti-Skid’ tape and all entrances and exits of module

Completely inspect all ‘rub-rails’ along bottom of

Inspect / replace rear Tow Hook surround mounting replace as needed all connecting receptacles, verifying all wiring is connected and functioning properly to meet CAAS 3.0 and UL requirements.

Exhibit C

Unit #1624 2015 Ford E450 158-inch Chassis

1 Remount of and Cutaway Van Ambulance (type III)

2024 or newer, Van Cutaway Chassis, largest Gas Engine available, 158"WB. Must meet or exceed all

5 Anti-Theft, Sound Off Signal ETISSO Ignition Security Systems

6 Back up Camera Monitor- Remove and Transfer for Existing Unit. Test and confirm functionality

Floor Cab Console, Custom Type III w/2 Cupholders, Large Map Slot and FWD Flat Section for Computer

8 Stealth Switch, Cab/Mod Unlock Switch, Cab Grille

9 Running Boards, Grip Strut, Pair

Aluminum “Alcoa Style” wheels front and outside rear with Steel mounted on the inside rear. Rear wheels

13 Black Undercoating, Rear Bumper Supports

Non-Emergency ‘Scene’ Lights – Reuse Existing Lights where able. If unable to reuse any existing lights, replace with same brand/style. Any changes will need to be approved by Rowan EMS prior to able. If unable to reuse any existing lights, replace with same style. Any changes will need to be approved by Rowan EMS prior to installation. Any

16 Inspect siren speakers, if replacement is required, Unit #1624 Continued

ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

17 Inspect / replace as needed lighting Flanges, Whelen Chrome to match existing

18 Module Interior - Clean & Inspect

Paint – Exterior of module shall be completely inspected. Any scratches and required body work shall be repaired and repainted to a color (white) matching chassis and original module color. Any

Graphics, module area. Exact colors and graphics to be determined during prebuild. Any decals removed during body repair shall be replaced and shall match original decals. If entire graphics from box are

24 Repair any minor body work on sides of Module

Clean/Inspect existing console. Replace only as needed. If replacement is warranted, switch location, radio location and computer mounting should mirror existing console. Repair/cover existing hole in which meets or exceeds Manufacturer Specifications (Bull Bars will not be accepted) All Siren Speakers

(named above) and air horns shall be mounted within

Stryker Power-PRO XT 6506 cot system -transfer from existing module, tested in working order prior to delivery.

29 Inspect and replace any missing drip rails on module

30 Estimated Build Time from award of Bid

31 Inspect/replace as needed all grabrails located throughout module

ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

Replace all AC electrical connections and covers on

33 Inspect/replace as needed all existing rub rails with same as existing

34 Install ground clearance lighting, wired to illuminate upon opening of any exterior doors.

Inspect / replace as needed Inverter with pure sine

36 Inspect / replace aluminum fuel filler cap housing.

37 Inspect and/or replace as needed any aluminum “Diamond Plate” on exterior of module

38 Replace existing “door grabbers” on rear module door. Each door shall have two (2) grabbers

39 Inspect / replace as needed all door latches and associated connecting rods and/or cables

Inspect/replace as needed interior Captains Seat with

43 Inspect bench seat padding and vinyl. Recover as

44 Install two (2) new portable O2 brackets; location to be determined.

Install one (1) SIERRA MG90 5G AIRLINK 5G Airlink wireless gateway, provided by the dealer or manufacturer. The MG90 5G shall be installed in the cabinet containin existing gaeway and shall be powered by the unswitched 12v, +/- 15-amp circuit

46 Replace all exterior module door gaskets with new, 47 Install Aeroclave connection port. Exact locations and specifics to be provided during prebuild meeting

48 Install “Grover” style airhorns with trumpet located as noted above.

Replace all seatbelts throughout module. All seatbelts should be red in color and meet or exceed all current SAE Automotive and CAAS 3.0 standards. Seatbelt and anchorages must meet or exceed Motor Vehicle Seat Belt Anchorages - Performance Requirements, ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

Replace rear bumper. Any replacement components

52 Replace ‘Anti-Slip’ tape on the floor at all entry points;

Completely inspect and repair any holes found on exterior of module to include exterior doors, side panels, or other areas which are not designed to have such holes. Replace any missing drip rails replace as needed all connecting receptacles, verifying all wiring is connected and functioning properly to meet CAAS 3.0 and UL requirements.

56 Test entire Oxygen delivery system. Repair any leaks

57 Replace all ‘Anti-Skid’ tape and all entrances and exits of module

58 Inspect / replace as needed lighting Flanges, Whelen

Exhibit D

Unit #1717 2017 Ford E450 158-inch Chassis

1 Remount of and Cutaway Van Ambulance (type III)

2024 or newer, Van Cutaway Chassis, largest Gas Engine available, 158"WB. Must meet or exceed all

3 Inspect and replace any missing drip rails on module

5 Anti-Theft, Sound Off Signal ETISSO Ignition Security Systems

Install Knox brand KnoxLock MedVault 2.75, Large, 7 Back up Camera Monitor- Remove and Transfer for Existing Unit. Test and confirm functionality

Floor Cab Console, Custom Type III w/2 Cupholders, Large Map Slot and FWD Flat Section for Computer

9 Stealth Switch, Cab/Mod Unlock Switch, Cab Grille

10 Running Boards, Grip Strut, Pair

Aluminum “Alcoa Style” wheels front and outside rear with Steel mounted on the inside rear. Rear wheels

14 Black Undercoating, Rear Bumper Supports

Non-Emergency ‘Scene’ Lights – Reuse Existing Lights where able. If unable to reuse any existing lights, replace with same brand/style. Any changes will need to be approved by Rowan EMS prior to able. If unable to reuse any existing lights, replace with same style. Any changes will need to be approved by Rowan EMS prior to installation. Any

Unit #1717 Continued

ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

17 Inspect siren speakers, if replacement is required, must be Dual Federal Signal, 100 Watts, In Bumper

18 Module Interior - Clean & Inspect

Paint – Exterior of module shall be completely inspected. Any scratches and required body work shall be repaired and repainted to a color (white) matching chassis and original module color. Any

Graphics, module area. Exact colors and graphics to be determined during prebuild. Any decals removed during body repair shall be replaced and shall match original decals. If entire graphics from box are

23 Repair any minor body work on sides of Module

Clean/Inspect existing console. Replace only as needed. If replacement is warranted, switch location, radio location and computer mounting should mirror existing console. Repair/cover existing hole(s) in console. All repair work should be professional in nature with like/same materials as existing console which meets or exceeds Manufacturer Specifications (Bull Bars will not be accepted) All Siren Speakers

(named above) and air horns shall be mounted within

Stryker Power-PRO XT 6506 cot system -transfer from existing module, tested in working order prior to delivery.

29 Inspect/replace as needed all grabrails located throughout module

Replace all AC electrical connections and covers on

31 Inspect/replace as needed all existing rub rails with

ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

32 Install ground clearance lighting, wired to illuminate upon opening of any exterior doors.

Inspect / replace as needed Inverter with pure sine

Inspect / replace (only as needed) aluminum fuel filler cap housing. Repair any bodywork if modifications are needed

35 Inspect and/or replace as needed any aluminum “Diamond Plate” on exterior of module

36 Replace existing “door grabbers” on rear module door. Each door shall have two (2) grabbers

37 Inspect / replace as needed all door latches and associated connecting rods and/or cables

Inspect/replace as needed interior Captains Seat with

41 Inspect bench seat padding and vinyl. Re-cover as

42 Install two (2) new portable O2 brackets; location to be determined.

Install one (1) SIERRA MG90 5G AIRLINK 5G Airlink wireless gateway, provided by the dealer or manufacturer. The MG90 5G shall be installed in the cabinet containin existing gaeway and shall be powered by the unswitched 12v, +/- 15-amp circuit

44 Replace all exterior module door gaskets with new, 45 Install Aeroclave connection port. Exact locations and specifics to be provided during prebuild meeting

46 Replace ‘Anti-Slip’ tape on the floor at all entry points;

side and rear

47 Install “Grover” style airhorns with trumpet located as noted above.

Replace all seatbelts throughout module. All seatbelts should be red in color and meet or exceed all current SAE Automotive and CAAS 3.0 standards. Seatbelt and anchorages must meet or exceed Motor Vehicle Seat Belt Anchorages - Performance Requirements, ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

49 Install “brow light” under existing AC Evaporator unit on front of module

Replace OEM mirrors with Velvac brand aftermarket

51 Test entire Oxygen delivery system. Repair any leaks

52 Replace all ‘Anti-Skid’ tape and all entrances and exits of module

Completely inspect all ‘rub-rails’ along bottom of replace as needed all connecting receptacles, verifying all wiring is connected and functioning properly to meet CAAS 3.0 and UL requirements.

56 Inspect / replace as needed lighting Flanges, Whelen

Exhibit E

Unit #1818 2018 Ford E450 158-inch Chassis

1 Remount of and Cutaway Van Ambulance (type III)

2024 or newer, Van Cutaway Chassis, largest Gas Engine available, 158"WB. Must meet or exceed all

Install Knox brand KnoxLock MedVault 2.75, Large, 6 Anti-Theft, Sound Off Signal ETISSO Ignition Security Systems

7 Back up Camera Monitor- Remove and Transfer for Existing Unit. Test and confirm functionality

Floor Cab Console, Custom Type III w/2 Cupholders, Large Map Slot and FWD Flat Section for Computer

9 Stealth Switch, Cab/Mod Unlock Switch, Cab Grille

10 Running Boards, Grip Strut, Pair

Aluminum “Alcoa Style” wheels front and outside rear with Steel mounted on the inside rear. Rear wheels

14 Test entire Oxygen delivery system. Repair any leaks

15 Black Undercoating, Rear Bumper Supports

16 Replace all ‘Anti-Skid’ tape and all entrances and exits of module

Non-Emergency ‘Scene’ Lights – Reuse Existing Lights where able. If unable to reuse any existing lights, replace with same brand/style. Any changes will need to be approved by Rowan EMS prior to

Unit #1818 Continued

ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

Emergency Lighting – Reuse Existing Lights where able. If unable to reuse any existing lights, replace with same style. Any changes will need to be approved by Rowan EMS prior to installation. Any

19 Inspect siren speakers, if replacement is required, 20 Inspect / replace as needed lighting Flanges, Whelen Chrome to match existing

21 Module Interior - Clean & Inspect

Paint – Exterior of module shall be completely inspected. Any scratches and required body work shall be repaired and repainted to a color (white) matching chassis and original module color. Any

Graphics, module area. Exact colors and graphics to be determined during prebuild. Any decals removed during body repair shall be replaced and shall match original decals. If entire graphics from box are

25 Repair any minor body work on sides of Module

Clean/Inspect existing console. Replace only as needed. If replacement is warranted, switch location, radio location and computer mounting should mirror existing console. Repair/cover existing hole(s) in console. All repair work should be professional in nature with like/same materials as existing console which meets or exceeds Manufacturer Specifications (Bull Bars will not be accepted) All Siren Speakers

(named above) and air horns shall be mounted within

Stryker PowerLOAD cot system - transfer from existing module, tested in working order prior to delivery

30 Inspect and replace any missing drip rails on module

31 Estimated Build Time from award of Bid

ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

32 Inspect/replace as needed all grabrails located throughout module

Replace all AC electrical connections and covers on

34 Inspect all existing rub rails; replace as needed with

35 Install ground clearance lighting, wired to illuminate upon opening of any exterior doors.

Inspect / replace as needed Inverter with pure sine

37 Inspect / replace aluminum fuel filler cap housing.

38 Inspect and/or replace as needed any aluminum “Diamond Plate” on exterior of module

39 Replace existing “door grabbers” on rear module door. Each door shall have two (2) grabbers

40 Inspect / replace as needed all door latches and associated connecting rods and/or cables

Inspect/replace as needed interior Captains Seat with

44 Inspect bench seat padding and vinyl. Recover as

45 Install two (2) new portable O2 brackets; location to be determined.

Install one (1) SIERRA MG90 5G AIRLINK 5G Airlink wireless gateway, provided by the dealer or manufacturer. The MG90 5G shall be installed in the cabinet containin existing gaeway and shall be powered by the unswitched 12v, +/- 15-amp circuit

47 Replace all exterior module door gaskets with new, 48 Install Aeroclave connection port. Exact locations and specifics to be provided during prebuild meeting

49 Install “Grover” style airhorns with trumpet located as noted above.

ITEM SPECIFICATIONS COMMENTS or ALTERNATIVES

Replace all seatbelts throughout module. All seatbelts should be red in color and meet or exceed all current SAE Automotive and CAAS 3.0 standards. Seatbelt and anchorages must meet or exceed Motor Vehicle Seat Belt Anchorages - Performance Requirements, 53 Replace ‘Anti-Slip’ tape on the floor at all entry points;

Completely inspect and repair any holes found on exterior of module to include exterior doors, side panels, or other areas which are not designed to have such holes. Replace any missing drip rails

56 Install “brow light” under existing AC Evaporator unit on front of module

57 Inspect / replace as needed lighting Flanges, Whelen Chrome to match existing

Lights Whelen TIR6 500 LED, Red/Clear – Front

Transfer Lights Whelen TIR6 500 LED, Red/Clear – Front Grille. Replace as neededGrille replace as needed all connecting receptacles, verifying all wiring is connected and functioning properly to meet CAAS 3.0 and UL requirements.

60 Inspect / replace as needed lighting Flanges, Whelen