Engineering Data Requirements.pdf

REV: ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

CONTROL UNIT‐GUN. F‐16

2. PART NUMBER:

16VS003001‐2

3. NATIONAL STOCK NUMBER:

1005‐01‐055‐7373WF

PREPARED BY:

BILL GARCIA

OFFICE SYMBOL:

416 SCMS/GUEAA

DATE:

4 MARCH 2020

HILL AFB FORM 462 Page 1 of 2

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC., WILL BE USED IN LIEU OF THE DATA INDICATED. THE SUPERSEDED DATA

WILL NOT BE FURNISHED UNLESS SO INDICATED.

5. THE SOURCES/MATERIALS IF LISTED ON THE STANDARDS, SPECIFICATION AND DRAWINGS ARE THE ONLY SOURCES/MATERIALS FOR THOSE ITEMS. SUBSTITUTIONS SHALL HAVE PRIOR APPROVAL BY THE COGNIZANT ENGINEERING

ACTIVITY.

6. DEVIATIONS FROM SPECIFICATIONS IDENTIFIED IN CONTROL DRAWINGS ARE NOT AUTHORIZED WITHOUT PRIOR APPROVAL

BY THE COGNIZANT ENGINEERING ACTIVITY.

7. MARKING PER MIL‐STD‐130 IN LIEU OF FPS‐3008.

8. IUID PART MARKING IS REQUIRED FOR THIS ITEM. MARK PER THE FOLLOWING REQUIREMENTS:

‐ F‐16 AIRCRAFT CONTROLLER SENSOR ASSEMBLY (PN 11217‐2) SHALL BE MARKED WITH A UNIQUE ITEM IDENTIFIER

(UII). (REF: MIL‐STD‐130)

‐ IF NO UII MATRIX IS PRESENT, FABRICATE NEW IDENTIFICATION PLATE (200945069‐501) AND ATTACH TO THE EXISTING IDENTIFICATION PLATE/LABEL, TO THE RIGHT OF THE "NSN" AND "CONTR" BLOCKS. DO NOT COVER ANY

EXISTING INFORMATION

‐ THE NEW UID IDENTIFICATION PLATE WILL BE LOCATED ON THE EXISTING PLATE/LABEL AS SHOWN ON THE NEXT

PAGE.

‐ UID LABEL P/N 200945085‐005A IS AN ACCEPTABLE ALTERNATE

REV: ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

CONTROL UNIT‐GUN. F‐16

2. PART NUMBER:

16VS003001‐2

3. NATIONAL STOCK NUMBER:

1005‐01‐055‐7373WF

PREPARED BY:

BILL GARCIA

OFFICE SYMBOL:

416 SCMS/GUEAA

DATE:

4 MARCH 2020

HILL AFB FORM 462 Page 2 of 2

9. CONTRACTORS THAT SUPPLY ELECTRONIC PARTS OR SYSTEMS THAT CONTAIN ELECTRONIC PARTS SHALL ESTABLISH POLICIES AND PROCEDURES TO AVOID, DETECT, MITIGATE AND DISPOSITION COUNTERFEIT ELECTRONIC PARTS TO PREVENT SUCH PARTS FROM ENTERING THE USAF/DOD SUPPLY CHAIN. THESE POLICIES AND PROCEDURES SHALL BE DOCUMENTED IN A COUNTERFEIT PARTS PREVENTION PLAN (CPPP) IN ACCORDANCE WITH (IAW) DATA ITEM DESCRIPTION (DID) DI‐MISC‐81832 OR SIMILAR DOCUMENT (E.G., EXISTING COMPANY COUNTERFEIT PARTS PREVENTION POLICIES/PLANS) AS REQUIRED BY THIS CONTRACT.

THE CONTRACTOR SHALL ACCOMPLISH THE POLICIES AND PRACTICES IDENTIFIED IN THE CPPP FOR ALL ACTIVITIES ASSOCIATED WITH THIS CONTRACT. THE REQUIREMENTS ESTABLISHED BY THE CPPP ALSO APPLY TO ELECTRONICS COMPONENTS PROCURED IN SUSTAINMENT (E.G., REPAIR) OF SUCH SYSTEMS AND ASSEMBLIES. THE REQUIREMENTS OF THE DOD‐ADOPTED SAE 5553 (AS5553), AEROSPACE STANDARD, COUNTERFEIT ELECTRONICS PARTS; AVOIDANCE, DETECTION, MITIGATION, AND DISPOSITION SHALL APPLY TO THIS CONTRACT. REPORTING IAW AS5553, 4.1.7, SHALL INCLUDE NOTIFICATION TO THE

CONTRACTING OFFICER OF THIS CONTRACT.