Attachment 2 Description 3612-VH or EQUAL - Bandsaw.docx
DOCX document 21 KB Posted
- Attached to
- Vertical contour bandsaw DoAll 3612-VH or Equal
- Solicitation number
- FA671223Q0013
About this file
This document describes requirements for a vertical contour bandsaw for the 911th Airlift Wing of the Department of the Air Force Reserve Command. Essential specifications for the DoAll 3612-VH bandsaw or equal include a footprint of 56" L x 44" W x 80" H or smaller, 460V/60Hz/3-ph electrical requirements, a variable frequency drive motor, blade width capacity of 1/8" to 1", minimum 154" blade length, band speeds of 30-320 FPM and 550-5500 FPM, manual band tensioning, minimum 39 inch material pass height, mounted electrical controls with "T" slots for fixture mounting, hydraulic feed control, table tilt of at least 45 degrees negative to 10 degrees positive, a welder/grinder, blade door interlocks, preset band tension device, and safety features such as an emergency stop button. The bandsaw must also include blade guards, a chip box, work holding fixtures, lubrication equipment, and extended warranty and training options. The government is responsible for material handling, installation, and waste disposal; the contractor must provide leveling if needed.
View the file
Other files
| File | Type | Posted |
|---|---|---|
| Attachment 3 Pricing Template.docx | DOCX document | |
| Attachment 1 COMBINED SYNOPSIS_SOLICITATION.docx | DOCX document |
On GovTribe
Work with this file
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
Bandsaw DoAll 3612-VH or Equal
Bandsaw:
The bandsaw is a requirement for our Custodian Authorization Custody Receipt Listing (CACRL) equipment, which means that is a required piece of equipment for our C-17 aircraft.
Essential Characteristics:
| Footprint Maximum: | 56” L x 44” W x 80” H (Footprints larger than this will not be considered). Quotes must clearly show the footprint of the bandsaw. | |||
| Electrical Requirements: | Must be 460V/60Hz/3-ph | |||
| Band Motor: | Must contain a Variable Frequency Drive | |||
| Blade Width Capacity: | 1/8” to 1” | |||
| Blade Length: | minimum length 154” | |||
| Band Speed: | 30-320 FPM (low range) | |||
| 550-5500 FPM (high range) | ||||
| Band Tension: | Manual | |||
| Material Pass Height: | minimum 39 Inches | |||
| Electrical Controls: | Must be mounted | |||
| Table Features: | Must have “T” slots for fixture mounting to prevent material from moving during cutting (12 inches of travel) | |||
| Feed Control: | Must have Hydraulic Feed Control to maximize band life | |||
| Table Tilt: | At least 45 Degrees Negative to at least 10 Degrees Positive | |||
| Welder/Grinder: | Welder with grinder for 460 Volt | |||
| Interlock: | Band door interlocks, so the band cannot be started while the doors are open | |||
| Preset Band Tension Device: | Allows the operator/user to correctly tension the blade during the band change |
Shall include the following:
· Emergency Stop Button, Blade Start Button, and Blade Stop Button
· Blade Guard and Tension control device IAW OSHA 1910.213
· Work holding jaw with handles
· Work holding vice to fit table “T” slots
· Magnetic wand chip remover
· Flood coolant
· Work Light
· Chip Box
· Chip Blower
· Saw Blade Guards
· Band Mist Lubricator
· Table Feed Control
· Post Elevating Hand Wheel required to keep the upper saw guide block as close to the top of the material being cut without getting their hands close to the blade during adjustment. Assists with minimizing blade deflection and increasing band life and safety
· Tool saver lubricant stick
· 5-gallon pail of mist coolant (and/or any other fluid necessary for start-up)
· Option for extended warranty on the machine (10 year)
Materials to be cut:
· Primary: aluminum
· Secondary: Steel, wood and plexiglass
Size of material to be cut:
· Up to ½ inch thick. Will need to be capable of cutting L angles
Delivery Address:
· 911th Airlift Wing 2601 Defense Ave Building 418 Coraopolis, PA 15108
Unloading of bandsaw:
· Government is responsible for using forklift/material handling equipment to offload bandsaw and movement to the installation point
Bandsaw leveling:
· There is a slight slope in the floor. Contractor responsible for ensuring band saw is level
Installation:
· Government responsible for making bandsaw electrical connection. Vendor responsible for initial start-up
Training:
· Vendor to provide in-person training on proper use of bandsaw to audience of up to seven. Test cuts shall be performed during training with material provided by the government.
Disposal of packaging/misc waste:
Government to dispose of packaging material
File details come from the government source that posted it. Updated .