Att_03_FS_Supplemental_Specifications_(240401).pdf

Table of Contents Preface

101 - Terms¸ Format¸ and Definitions

101.01 Meaning of Terms

101.03 Abbrevia ons

101.04 Defini ons

102 - Bid¸ Award¸ and Execution of Contract

Delete Sec on 102

103 - Scope of Work

Delete Subsec ons 103.02, 103.03, 103.04, 103.05

104 - Control of Work

Delete Subsec ons 104.01, 104.02, 104.04

104.06 Use of Roads by Contractor

106 - Acceptance of Work

106.01 Conformity with Contract Requirements

106.02 Visual Inspec on

107 - Legal Relations and Responsibility to the Public

Delete Subsec on 107.05

108 - Prosecution and Progress

Delete Sec on 108

109 - Measurement and Payment

Delete Subsec ons 109.06, 109.07, 109.08, 109.09

109.02 Measurement Terms and Defini ons

155 - Schedules for Construction Contracts

Delete Sec on 155

301 - Untreated Aggregate Courses

301.03 General

Preface Preface_wo_03_28_2024

Delete all but the first paragraph and add the following:

The Forest Service, US Department of Agriculture has adopted FP-14 for construction of National Forest System Roads.

101 - Terms¸ Format¸ and Definitions 101.01_National_11_9_2016

Add the following paragraph to Subsection 101.01:

101.01 Meaning of Terms.

Delete all references to the TAR (Transporta on Acquisi on Regula ons) in the specifica ons.

101.03_National_11_9_2016

Add the following to Subsection 101.03:

101.03 Abbrevia ons.

(a) Acronyms.

AGAR — Agriculture Acquisi on Regula ons

AFPA — American Forest and Paper Associa on

FSAR — Forest Service Acquisi on Regula ons

MSHA — Mine Safety and Health Administra on

NESC — Na onal Electrical Safety Code

WCLIB — West Coast Lumber Inspec on Bureau

(f) Miscellaneous unit abbrevia ons.

MP — milepost loca on ppm — parts per million volume

STA sta on loca on

101.04_National_11_9_2016

Make the following changes to Subsection 101.04:

101.04 Defini ons.

Delete these definitions and replace the following:

Bid Schedule — The Schedule of Items.

Bridge — A structure, including supports, erected over a depression or an obstruc on such as water along a road, a trail, or a railway and having a deck for carrying traffic or other loads.

Contractor — The individual or legal en ty contrac ng with the Government for performance of prescribed work. In a mber sale contract, the contractor is the “Purchaser”.

Culvert — Any structure with a bo om, regardless of fill depth, depth of invert burial, or presence of horizontal driving surface, or any bo omless (natural channel) structure with foo ngs that will not have wheel loads in direct contact with the top of the structure.

Drawings — (Public Works Contracts) Design sheets or fabrica on, erec on, or construc on details submi ed to the CO by the Contractor according to FAR Clause 52.236‐21 Specifica ons and Drawings for Construc on. Also refers to submissions and submi als.

No ce to Proceed — (Public Works Contracts) Wri en no ce to the Contractor to begin the contract work.

Right‐of‐Way — A general term deno ng (1) the privilege to pass over land in some par cular line

(including easement, lease, permit, or license to occupy, use, or traverse public or private lands), or (2)

Real property necessary for the project, including roadway, buffer areas, access, and drainage areas.

Solicita on—(Public Works Contracts) The complete assembly of documents (whether a ached or incorporated by reference) furnished to prospec ve bidders.

Add the following definitions:

Adjustment in Contract Price — “Equitable adjustment,” as used in the Federal Acquisi on Regula ons, or “construc on cost adjustment,” as used in the Timber Sale Contract, as applicable.

Change — “Change” means “change order” as used in the Federal Acquisi on Regula ons, or “design change” as used in the Timber Sale Contract.

Forest Service — The United States of America, ac ng through the Forest Service, U.S. Department of

Agriculture.

Neat Line — A line defining the proposed or specified limits of an excava on or structure.

Pioneer Road — Temporary construc on access built along the route of the project.

Purchaser — The individual, partnership, joint venture, or corpora on contrac ng with the Government under the terms of a Timber Sale Contract and ac ng independently or through agents, employees, or subcontractors.

Protected Streamcourse — A drainage shown on the plans or mber sale area map that requires designated mi ga on measures.

Road Order — An order affec ng and controlling traffic on roads under Forest Service jurisdic on. Road

Orders are issued by a designated Forest Officer under the authori es of 36 CFR, part 260.

Shop Drawings — (Timber and Stewardship Contracts) Referred to as “Drawings” in FP‐14, include drawings, diagrams, layouts, schema cs, descrip ve literature, illustra ons, lists or tables, performance and test data, and similar materials furnished by Purchaser to explain in detail specific por ons of the work required by the contract.

U liza on Standards — The minimum size and percent soundness of trees described in the specifica ons to determine merchantable mber.

Add Figure 101-1—Illustration of road structure terms:

Figure 101‐1—Illustra on of road structure terms.

102 - Bid¸ Award¸ and Execution of Contract 102.00_National_11_9_2016

Delete Section 102 in its entirety.

Delete Sec on 102.

103 - Scope of Work 103.00_National_11_9_2016

Delete all of Section 103 except Subsection 103.01 Intent of Contract.

Delete Subsec ons 103.02, 103.03, 103.04, 103.05.

104 - Control of Work 104.00_National_11_9_2016

Delete Subsections 104.01, 104.02, and 104.04.

Delete Subsec ons 104.01, 104.02, 104.04.

104.06_National_11_9_2016

Add the following to Subsection 104.06:

104.06 Use of Roads by Contractor.

The Contractor is authorized to use roads under the jurisdic on of the Forest Service for all ac vi es necessary to complete this contract, subject to the limita ons and authoriza ons designated in the Road

Order(s) or described in the contract, when such use will not damage the roads or na onal forest resources, and when traffic can be accommodated safely.

106 - Acceptance of Work 106.01_National_7_18_2017

Delete Subsection 106.01 and replace with the following:

106.01 Conformity with Contract Requirements.

Follow the requirements of FAR Clause 52.246‐12 Inspec on of Construc on.

References to standard test methods of AASHTO, ASTM, GSA, and other recognized standard authori es refer to the methods in effect on the date of solicita on for bids.

Perform all work to the lines, grades, cross‐sec ons, dimensions, and processes or material requirements shown on the plans or specified in the contract.

Incorporate manufactured materials into the work according to the manufacturer’s recommenda ons or to these specifica ons, whichever is more strict.

Plan dimensions and contract specifica on values are the values to be strived for and complied with as the design values from which any devia ons are allowed. Perform work and provide material that is uniform in character and reasonably close to the prescribed value or within the specified tolerance range. The purpose of a tolerance range is to accommodate occasional minor varia ons from the median zone that are unavoidable for prac cal reasons.

When standard manufactured items are specified (such as fence, wire, plates, rolled shapes, pipe conduits, etc., that are iden fied by gauge, unit mass, sec on dimensions, etc.), the iden fica on will be considered to be nominal masses or dimensions. Unless specific contract tolerances are noted, established manufacturing tolerances will be accepted.

The Government may inspect, sample, or test all work at any me before final acceptance of the project.

When the Government tests work, copies of test reports are furnished to the Contractor upon request.

Government tests may or may not be performed at the work site. If Contractor tes ng and inspec on is verified by the Government, the Contractor’s results may be used by the Government to evaluate work for acceptance. Do not rely on the availability of Government test results for process control.

Acceptable work conforming to the contract will be paid for at the contract unit bid price. Four methods of determining conformity and accep ng work are described in Subsec ons 106.02 to 106.05 inclusive.

The primary method of acceptance is specified in each Sec on of work. However, work may be rejected at any me it is found by any of the methods not to comply with the contract.

Remove, repair, or replace work that does not conform to the contract, or to prevailing industry standards where no specific contract requirements are noted. Removing, repairing, or replacing work;

providing temporary traffic control; and any other related work to accomplish conformity will be at no cost to the Government.

(a) Dispu ng Government test results. If the accuracy of Government test results is disputed, promptly inform the CO. If the dispute is unresolved a er reasonable steps are taken to resolve the dispute, further evalua on may be obtained by wri en request. Include a narra ve describing the dispute and a proposed resolu on protocol that addresses the following:

1. Sampling method;

2. Number of samples;

3. Sample transport;

4. Test procedures;

5. Testing laboratories;

6. Reporting;

7. Estimated time and costs; and

8. Validation process.

If the evalua on requires addi onal sampling or tes ng be performed, mutually agree with the

Government on witnessing procedures and on sampling and tes ng by a third party laboratory. Use a third party laboratory accredited by the AASHTO accredita on program. Provide proof of the laboratory’s accredita on for the test procedures to be used. Do not use the same laboratory that produced the disputed Government test results or that produced the test results used as a basis for the dispute.

The CO will review the proposed resolu on protocol and may modify it before final approval and execu on.

The Government will use the approved resolu on protocol test results to determine the validity of the disputed tes ng. If the Government test results are validated, the Contractor will be responsible for all costs associated with developing and performing the resolu on protocol. If the Government test results are not validated, the Government will be responsible for all costs associated with developing and performing the resolu on protocol. If the validity of the Government test results cannot be determined, the Contractor and Government will equally share all costs associated with developing and carrying out the resolu on protocol.

(b) Alterna ves to removing and replacing non‐conforming work. As an alterna ve to removal and replacement, the Contractor may submit a wri en request to:

1. Have the work accepted at a reduced price; or

2. Be given permission to perform corrective measures to bring the work into conformity.

The request must contain suppor ng ra onale and documenta on. Include references or data jus fying the proposal based on an evalua on of test results, effect on service life, value of material or work, quality, aesthe cs, and other tangible engineering basis. The CO will determine disposi on of the nonconforming work.

106.02_National_11_9_2016

Delete Subsection 106.02 and replace with the following:

106.02 Visual Inspec on.

Acceptance is based on visual inspec on of the work for compliance with the specific contract requirements. Use prevailing industry standards in the absence of specific contract requirements or tolerances.

107 - Legal Relations and Responsibility to the Public 107.05_National_7_18_2017

Delete Subsection 107.05.

Delete Subsec on 107.05.

108 - Prosecution and Progress 108.00_National_11_9_2016

Delete Section 108 in its entirety.

Delete Sec on 108.

109 - Measurement and Payment 109.00_National_11_9_2016

Delete Subsections 109.06, 109.07, 109.08, and 109.09:

Delete Subsec ons 109.06, 109.07, 109.08, 109.09.

109.02_National_11_9_2016

Add the following sentence to Subsection 109.02(b):

109.02 Measurement Terms and Defini ons.

(b) Contract quan ty.

Contract quan es will be adjusted only when there are errors in the original design of 15% or more.

155 - Schedules for Construction Contracts 155.00_National_11_9_2016

Delete Section 155 in its entirety.

Delete Sec on 155.

301 - Untreated Aggregate Courses 301.03_National_7_17_2017

Add the following to Subsection 301.03:

301.03 General.

Wri en approval of the roadbed is required before placing aggregate.

For pit run or grid‐rolled material, furnish material smaller than the maximum size, no grada on will be required otherwise. A er processing on the road, remove all oversize material from the road and dispose as directed by the CO.

Provide addi ves or binder, if required, at the propor ons specified.

Develop and use Government furnished sources according to Sec on 105.

If the aggregate is produced and stockpiled before placement, handle and stockpile according to Sec on

314.