462ENGINEERINGDATAREQUIRMENTS.pdf

REV: ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

GUN ACCESS DOOR

2. PART NUMBER:

160D115028-127

3. NATIONAL STOCK NUMBER:

1560-01-063-2132 FJ

PREPARED BY:

JASON HUFFMAN

OFFICE SYMBOL:

416 SCMS/GUMBA

DATE:

1/29/2013

HILL AFB FORM 462 Page 1 of 3

4. THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC. WILL BE USED IN LIEU OF THE DATA INDICATED. THE

SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.

5. THE CONTRACTOR IS RESPONSIBLE TO COMPLETELY RESEARCH THESE MANUALS, SPECIFICATIONS, AND STANDARDS AND FULLY UNDERSTAND THE REQUIREMENTS NECESSARY FOR THE MANUFACTURE OF COMPONENT PARTS AND ASSEMBLIES. ALL DEVIATIONS, MINOR AND MAJOR, FROM THE ENGINEERING DRAWING PACKAGE SHALL

BE SUBMITTED TO 416 SCMS/GUMBA, A-10 STRUCTURAL ENGINEERING FOR APPROVAL.

6. WHEN MILITARY DOCUMENTS LISTED IN THE ENGINEERING DRAWING ARE CANCELLED THEY SHALL BE REPLACED BY THE INDUSTRY EQUIVALENT DOCUMENT SPECIFIED ON THE MILITARY DOCUMENT’S CANCELLATION NOTICE. THIS APPLIES TO THE ORIGINAL AIRCRAFT MANUFACTURER’S SPECIFICATIONS THAT ARE CITED IN THE DRAWING, AS WELL. THE CHARACTERISTICS OF TYPE, GRADE, CLASS, ETC. SPECIFIED IN THE CANCELLED MILITARY DOCUMENT SHALL BE MAINTAINED OR EXCEED THOSE CHARACTERISTICS WHEN APPLYING THE INDUSTRY EQUIVALENT DOCUMENT(S). WHEN THERE IS NO LISTED REPLACEMENT THE CONTRACTOR SHALL REQUEST AND

RECOMMEND A SUBSTITUTE DOCUMENT THROUGH THE GOVERNMENT CONTRACTING OFFICIAL.

7. USE OF NORTHROP GRUMMAN SPECIFICATION Z-R701 IN CONJUNCTION WITH MIL-STD-130 IS MANDATORY TO ENSURE THE PROPER MARKING OF THE PARTS. (Z-R701 HAS UNLIMITED DATA RIGHTS IN JEDMICS)

8. "IUID" (ITEM UNIQUE IDENTIFIER) IS REQUIRED IAW MIL-STD-130. SPECIFIC INSTRUCTIONS FOR MARKING METHODS, LOCATION, CONTENT AND FORMAT SHALL BE SPECIFIED BY THE CONTRACTOR AND SUBMITTED TO THE GOVERNMENT FOR APPROVAL PRIOR TO CONTRACT DELIVERY. THE CONTRACTOR MUST DEMONSTRATE THE MARKING DOES NOT ADVERSELY AFFECT ITEM INTEGRITY OR PERFORMANCE AND WILL REMAIN READABLE AND ATTACHED THROUGHOUT THE USEABLE LIFE OF THE ITEM. IUID IS REQUIRED FOR ITEMS WHERE THE INDIVIDUAL COST PER UNIT IS GREATER THAN $5,000 OR IF THE ITEM HAS BEEN IDENTIFED AS FATIGUE CRITICAL REGARDLESS OF THE ITEMS PER

UNIT COST.

9. UNIQUE IDENTIFICATION (UID) SHALL BE APPLIED TO EACH PART PER MIL-STD-130 WITH THE ADDITION THE NSN.

THE UID SHALL BE BOTH HUMAN READABLE INFORMATION (HRI) MARKINGS AND MACHINE-READABLE INFORMATION (MRI) MARKS. THE MRI SHALL BE ACCOMPANIED BY A HRI. THE HRI SHALL APPEAR AS FOLLOWS:

CAGE 77751

P/N 160D115028-127

S/N #####MMYYNNNN

WHERE ##### IS THE VENDOR CAGE (FSCM OF THE CONTRACTOR NAMED ON THE CONTRACT, MMYY IS THE DATE OF MANUFACTURE, AND NNNN IS A UNIQUE 4-DIGIT NUMBER STARTING WITH 0001 IN NUMERICAL ORDER OF

MANUFACTURE.

THE HEIGHT OF EACH ALPHANUMERIC CHARACTER IN THE HRI SHALL BE A MAXIMUM OF .125 INCHES. MARKINGS FOR BOTH THE MRI AND HRI SHALL BE TO SAE AS 9132. THE METHOD OF MARKING FOR THE MRI SHALL BE LIMITED TO TESA BRAND SECURE 6973 BLACK UID LASER ETCHED MARKING TAPE (FOR MORE INFORMATION REFER TO (WWW.TESATAPE.COM/PROFESSIONAL/INDUSTRY/APPLICATIONS/UIDDOD) AND SHALL ONLY BE PLACED ON THE TOP COAT OF THE PAINTED COMPONENTS. THE MRI MARK ON THE TESA TAPE SHALL CONTAIN HRI EQUIVALENT INFORMATION IN BOTH 2D MATRIX FORM AND IN HUMAN READABLE FORM. WHEN ITEMS CANNOT BE FULLY MARKED OR TAGGED DUE TO LACK OF MARKING SPACE OR BECAUSE MARKING OR TAGGING WOULD HAVE A DELETERIOUS EFFECT, THE FULL DETAILED UID MARKING REQUIREMENTS SHALL BE APPLIED TO A SUPPLEMENTAL BAG OR OTHER

PACKAGE THAT ENCLOSES THE INDIVIDUAL ITEM.

HILL AFB FORM 462 Page 2 of 3

10. USE MS20001P12 STOCK IN LIEU OF 160D115028-25, 160D115028-41, 160D115028-43, 160D115028-45, AND 160D115028-47.

DO NOT CUT MS20001P12 INTO SEGMENTS (THIS WILL HELP FACILITATE 9475844 MOD). FROM STOCK MS20001P12 REMOVE CENTER PIN, SEPARATE HINGE SEGMENTS, REALIGN RIGHT HINGE SEGMENT (ROTATE 180 DEGREES ABOUT HORIZONTAL AXIS), AND THEN REASSEMBLE HINGE PER ATTACHED IMAGE. ALSO CUT HINGE PER DIMENSIONS

CALLED OUT IN IMAGE. ALL OTHER DIMENSIONS ARE STOCK DIMENSION OF THE MS20001P12.

See Note 10 Above

FWD

RIGHT

HILL AFB FORM 462 Page 3 of 3

11. DUE TO A CLEARANCE ISSUE BETWEEN THE 160D115028-123 ANGLE BRACKET AND THE 160D115028-79 ANGLE BRACKET, THE 160D115028-79 WILL BE TRIMMED TO FIT UNDER THE 160D115028-123 BRACKET.

12. MOD DRAWING 9475844 STATES THERE ARE 9 EQUAL SPACES BETWEEN 10 RIVETS TO ATTACH THE 160D115028-79 ANGLE BRACKET THIS IS IN CONFLICT WITH THE 8 LISTED ON THE 160D115028-127 DRAWING. FOLLOW THE DIRECTIONS OF THE MOD DRAWING AND ATTACH 10 EQUALLY SPACED RIVETS FOR A TOTAL OF 9 SPACES BETWEEN THE RIVETS.

13. INSTALL P/N 8730897-71 SCREEN WITH A LAYER OF MIL-S-81733 TYPE II-2 SEALANT, BETWEEN THE LOUVER (160D115028-27) AND THE DOOR SKIN IN ACCORDANCE WITH THE FIGURE BELOW. ENSURE SCREEN IS CENTERED WITH RESPECT TO THE LOUVER. IT IS PERMISSIBLE TO CUT SCREENS AT RIVET LOCATIONS TO ALLOW FOR INSTALLATION

OF THE RIVETS.