4 - Att B-3 - PID (Pulley).docx

Attachment 1 to SPE7LX20RXXXX to PID, Packaging, and Marking *** LTC PID Packaging Consolidated Text ***

PLEASE SEE GLOSSARY AT THE END OF THE DOCUMENT FOR FULL TEXT OF THE ITEM DESCRIPTION AND PACKAGING REFERENCE NUMBERS CALLED OUT FOR EACH NSN.

NSN: 3020005343151

PULLEY, GROOVE.

REFERENCE NUMBER: RA001

REFERENCE NUMBER: ZD003

REFERENCE NUMBER: RQ032

REFERENCE NUMBER: RD002

REFERENCE NUMBER: RQ001

REFERENCE NUMBER: RQ002

REFERENCE NUMBER: RQ009

REFERENCE NUMBER: RQ011

REFERENCE NUMBER: RQ016

REFERENCE NUMBER: RP001

REFERENCE NUMBER: RT001

REFERENCE NUMBER: ZD087

REFERENCE NUMBER: ZD080

E/I KC-135 AIRCRAFT.

EXCEPTIONS:

1) PART MARKING I/A/W MIL-STD-130 METHOD AS PER DRAWING REQUIREMENTS AND BAC 5307. MARKING MUST INCLUDE NSN, PART NUMBER, CURRENT DESIGN CODE (98748), ACTUAL MANUFACTURER CAGE CODE, DATE OF MANUFACTURE AND "FOR MILITARY USE ONLY" PARTS NOT TO BE MARKEDWITH THE ORIGINAL DESIGN AUTHORITY (BOEING) CAGE CODE.

2) DELETE REFERENCE TO BAC 5005, D2-5000

3) SURFACE TEXTURE PER ASME B46.1

4) DIMMENSIONS AND TOLERANCES PER ASME Y 14.5M

5) USE SAE AMS (5513H, 5516M, 5517L, 5518K, 5519M, 5524K, 5901B, 5902B, 5903A, 5904A, 5905A, 5906A, 5907A, 5910A, 5911A, 5912A AND 5913A) ILO MIL-S-5059

6) USE SAE AMS QQ-S-763A ILO QQ-S-763

7) USE ASTM A240/A240M REV A, ASTM A 666, AND ASTM A 693 ILO QQ-S-766

8) USE SAM AMS 5510R AND 5512K ILO MIL-S-6721

9) USE MIL PRF 23827 ILO MIL-G-3278

10) USE BAC 5975 ILO BAC 5930

11) EOO2011C0660-T AND EO2011C0663-T

12) FINISH CODE F-1.10 READS: APPLY NO FINISH, EXCEPT THAT TEMPORARY PROTECTION MAY BE APPLIED FOR HANDLING, TRANSPORTATION AND STORAGE.

13) USE SAE-AMS-2175A ILO MIL-C-6021B

REFERENCE NUMBER: ZDL01

REFERENCE NUMBER: CS187

REFERENCE NUMBER: CQ015

CRITICAL APPLICATION ITEM

IAW BASIC DRAWING NR 81205 5-97226

REVISION NR E DTD 08/05/1982

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81205 BACD2033

REVISION NR B DTD 02/06/1968

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81205 BACB10A

REVISION NR AT DTD 06/17/2011

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81205 BAC5975

REVISION NR M DTD 06/01/2005

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81205 BAC5975

REVISION NR M DTD 10/28/2008

PART PIECE NUMBER:

IAW REFERENCE SPEC NR MIL-PRF-23827C(2) NOT 2

REVISION NR 2 DTD 04/05/2016

PART PIECE NUMBER:

IAW REFERENCE NON GOVT STD SAE AMS5510S

REVISION NR S DTD 12/01/2008

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81205 BAC5300

REVISION NR M DTD 09/09/2011

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81205 BAC5423

REVISION NR W DTD 09/02/1999

PART PIECE NUMBER:

IAW REFERENCE NON GOVT STD SAE AMS5516P

REVISION NR P DTD 05/01/2007

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81205 EO2011C663-T

REVISION NR E DTD 05/24/2011

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81205 E02011C660-T

REVISION NR E DTD 04/21/2011

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81205 5-97226

REVISION NR DTD 05/21/2011

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81205 2011C0660-T

REVISION NR E DTD 04/21/2011

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81205 2011C0663-T

REVISION NR E DTD 05/24/2011

PART PIECE NUMBER:

IAW REFERENCE NON GOVT STD SAE AMS 5512

REVISION NR DTD

PART PIECE NUMBER:

IAW REFERENCE NON GOVT STD AMS-QQ-S-763D

REVISION NR D DTD 03/01/2015

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81205 BAC5300-2

REVISION NR H DTD 09/15/2014

PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81205 BAC5300-1

REVISION NR H DTD 06/23/2014

PART PIECE NUMBER:

PREP FOR DELIVERY

LINE ITEM 00001 TYPE OF COVERAGE: DLA DIRECT, CONUS

PKGING DATA-QUP: 001

WILL BE PACKAGED IN ACCORDANCE WITH ASTM D3951.

GLOSSARY

PACKAGING TEXT

THE FOLLOWING PARAGRAPH APPLIES TO ALL PACKAGING CALLED OUT IN THIS DOCUMENT: All DLA Master List of Technical and Quality Requirements take precedence over ASTM D3951. Mark and label all packaging and packing in accordance with MIL-STD-129. The Unit of Issue (U/I) and Quantity per Unit Pack (QUP) will be as specified in the contract/purchase order.

ITEM DESCRIPTION TEXT

REFERENCE NUMBER RA001

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

REFERENCE NUMBER ZD003

A metal casting process was identified as a means to manufacture this item. Tooling is required to produce a casting. For sourcing, tooling, materials or other information, please contact the appropriate assistance team: (Aviation, C&E Supply Chains) DSCR.AFCAT@dla.mil; (Land & Maritime Supply Chains) DSCC.cast.forge@dla.mil

REFERENCE NUMBER RQ032

RQ032: EXPORT CONTROL OF TECHNICAL DATA

This item has technical data some or all of which is subject to export-control of either the International Traffic in Arms regulations (ITAR) or the Export Administration Regulations (EAR), and cannot be exported without prior authorization from either the Department of State or the Department of Commerce. Export includes disclosure of technical data to foreign persons and nationals whether located in the United States or abroad. This requirement applies equally to foreign national employees and U.S. companies and their foreign subsidiaries. DFARS 252.225-7048 is applicable to this data.

The Defense Logistics Agency (DLA) limits distribution of export-control technical data to DLA contractors that have an approved US/Canada Joint Certification Program (JCP) certification, have completed the Introduction to Proper Handling of DOD Export-Controlled Technical Data Training and the DLA Export-Controlled Technical Data Questionnaire (both are available at the web address given below), and have been approved by the DLA controlling authority to access the export-controlled data. Instructions for obtaining access to the export-controlled data can be found at: https://www.dla.mil/HQ/LogisticsOperations/EnhancedValidation/

To be eligible for award, offerors and any sources of supply proposed for use are required to have an approved JCP certification and have been approved by the DLA controlling authority to access export-controlled data managed by DLA. DLA will not delay award in order for an offeror or its supplier to apply for and receive approval by the DLA controlling authority to access the export-controlled data.

REFERENCE NUMBER RD002

RD002, COVERED DEFENSE INFORMATION APPLIES

REFERENCE NUMBER RQ001

RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS)

REFERENCE NUMBER RQ002

RQ002: CONFIGURATION CHANGE MANAGEMENT - ENGINEERING CHANGE PROPOSAL REQUEST FOR VARIANCE (DEVIATION OR WAIVER)

REFERENCE NUMBER RQ009

RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN

REFERENCE NUMBER RQ011

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

REFERENCE NUMBER RQ016

RQ016: COMPONENT QUALIFIED PRODUCTS LISTS (QPL)/QUALIFIED MANUFACTURERS LISTS (QML). THIS ITEM CONTAINS ONE OR MORE COMPONENTS DEFINED BY A SPECIFICATION(S) WITH AN ASSOCIATED QUALIFIED PRODUCTS LIST (QPL) OR QUALIFIED MANUFACTURERS LIST (QML). QUALIFICATION REQUIREMENTS IN PROCUREMENT NOTE H02 "COMPONENT QUALIFIED PRODUCTS LIST (QPL)/QUALIFIED MANUFACTURERS LIST (QML)" APPLY.

REFERENCE NUMBER RP001

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

REFERENCE NUMBER RT001

RT001: MEASURING AND TEST EQUIPMENT

REFERENCE NUMBER ZD087

THIS NSN CONTAINS ONE OR MORE COMPONENTS WHICH MUST MEET QPL/QML REQUIREMENTS. BY SUBMITTING AN OFFER, THE OFFEROR AGREES TO PROVIDE QPL/QML COMPONENTS ONLY FROM SOURCES QUALIFIED ON THE APPLICABLE QPL(S)/QML(S).

REFERENCE NUMBER ZD080

SAMPLING: THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

REFERENCE NUMBER ZDL01

A BOEING RIGHTS GUARD LICENSE AGREEMENT 01 RESTRICTED TECHNICAL DATA PACKAGE EXISTS FOR THIS ITEM. DATA NON-DISCLOSURE AND DATA DESTRUCTION CONDITIONS APPLY. VENDORS MUST COMPLETE AND RETURN THE FORMS LOCATED IN THE "01 BOEING RIGHTS GUARD" LICENSE AGREEMENT FOLDER AVAILABLE AT https://pcf1x.bsm.dla.mil/cFolders

REFERENCE NUMBER CS187

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE USED NOR INCORPORATED IN ANY ITEMS TO BE DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT DOES NOT ALLEVIATE ANY PRODUCT REQUIREMENTS. SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR APPROVAL UNLESS THEY ARE AUTHORIZED BY THE SPECIFICATION REQUIREMENTS.

REFERENCE NUMBER CQ015

"FINAL INSPECTION AND ACCEPTANCE OF THE ITEM SHALL BE AT THE ACTUAL MANUFACTURING FACILITY. TECHNICAL INSPECTION IS REQUIRED. THE CONTRACTOR SHALL MAKE DRAWINGS AND TECHNICAL INFORMATION AVAILABLE TO VERIFY THAT THE ITEM MEETS ALL TECHNICAL REQUIREMENTS. COUNT, KIND, AND CONDITION INSPECTIONS ARE NOT ACCEPTABLE. THIS NOTE TAKES PRECEDENCE OVER MASTER SOLICITATION PART ONE PROVISIONS, NOTE 6, QUOTATIONS BY NON-MANUFACTURERS (APR 1984, DCSC 52.217-9C01). FINAL INSPECTION OF PACKAGING, IF REQUIRED, MAY BE CONDUCTED ELSEWHERE."