STATEMENT_OF_WORK.docx

UNITED STATES DEPARTMENT OF JUSTICE

FEDERAL BUREAU OF PRISONS

FCC VICTORVILLE

13777 AIR EXPRESSWAY BLVD.

VICTORVILLE CALIFORNIA, 92394

STATEMENT OF WORK 2018 ANNUAL ELECTRICAL INSPECTION

PART I - GENERAL INFORMATION

A. INTRODUCTION

Annual electrical inspection per Facilities Manual P.S. 4200.12

B. SCOPE

The following electrical equipment shall be tested according to manufacturer’s recommended procedures.

1. Seventy Two (72) MV Switches

2. Twenty Four (24) High Voltage Distribution Sections

3. Thirteen (13) High Voltage Switches

4. Utility Switchgear FCI1, with Four (4) protective relays

5. Utility Switchgear FCI2, with Four (4) protective relays

6. Utility Switchgear USP, with Four (4) protective relays

7. Four (4) protective relays

8. Protective Relays

9. Two (2) 951 Basler relays located in FCI2 & USP

10. Four (4) GPS Basler relays located in FCI2 & USP

11. Four (4) 87G Basler relays located in FCI2 & USP

12. Eight (8) 851 Basler relays located in FCI2 & USP

13. Twenty (20)DT3000 Eaton relays located in FCI2 & USP

14. Thirty Three (33) Oil Filled Transformers

15. Two (2) Dry Type Transformer

16. Two (2) Load Banks

17. Thirty Eight (39) High Voltage Circuit Breakers

(See Attachments)

PART II - WORK REQUIREMENTS

A. Switchgear and Switchboard Assemblies

1. Visual and Mechanical Inspection.

· Inspect for physical damage and proper installation.

· Inspect for proper alignment, anchorage and grounding.

· Inspect for proper identification of protective devices and switches.

· Physically test all mechanical interlocks to assure proper operation.

· Check tightness of accessible bolted bus connections.

· Clean switchboard interior compartments.

· Inspect insulators for evidence of physical damage or contaminated surfaces.

· Check key interlock systems for safe operation and proper key distribution. If applicable.

· Perform visual and mechanical inspection on all instrument transformers.

· Inspect control power transformers for physical damage, cracked insulation, broken leads, tightness of connections, defective wiring, and overall general condition.

· Verify correct functioning of instrument and control power transformer draw out disconnecting and grounding contacts and interlocks.

2. Electrical Tests

· Measure insulation resistance of each bus section phase-to-phase and phase-to ground.

B. Medium/High Voltage Load Interrupter Fusible Switch

1. Visual and Mechanical Inspection.

Inspect the switch and enclosure for cleanliness, condition of louvers and filters, corrosion and paint conditions.

Inspect the switch, bus, cable terminations and fuse holders for evidence of defects in insulation integrity, such as cracking, tracking, corona and overheating.

Inspect the switch contacts and arc chutes. Check for smooth movement, proper alignment and flicker blade operation per manufacturer’s procedures.

Verify that any mechanical and key interlock schemes function as intended.

Verify equipment ground connection.

Verify proper operation of space heaters.

Clean the cabinet floor and walls by vacuuming and wiping the walls.

Clean and lubricate the operating mechanism and blade contact surfaces per manufacturer’s guidelines.

Clean the switch, bus and support insulators by vacuuming and wiping. Some components may be cleaned with a manufacture approved electrical solvent.

2. Electrical Tests

Measure contact resistance for each phase.

Measure insulation resistance at the appropriate test value, each pole to ground, between phases and across open contacts of each phase.

C. Protective Relays

1. Visual and Mechanical Inspection.

Inspect relays for physical damage and proper installation.

Tighten case connections. Inspect cover for correct gasket seal. Inspect shorting hardware, connection paddles, and/or knife switches. Verify target reset.

Clean cover glass and relay components as required.

Check relay components for proper operation and alignment, as applicable.

Verify relays were set in accordance with coordination study supplied by owner.

Verify proper identification of protective relays.

2. Electrical Tests

Perform the following tests at the settings specified by client:

Pickup parameters on each operating element of the relay.

Timing tests conducted to verify proper delay of each element.

Pickup target and seal-in units.

Special tests as required checking operation of restraint, directional and other elements, per manufacturer's instructions.

Perform functional test to ensure relay trips the associated breaker or auxiliary device, as applicable.

Perform insulation resistance test on each electrical circuit to frame. Insulation resistance tests shall not be performed on solid-state protective relays.

C. Liquid Transformers

1. Visual and Mechanical Inspection.

Inspect the tank, radiators, control cabinets, fans and auxiliary devices for corrosion and paint condition.

Inspect the outside of the tank, radiators, sample valves, gauges and pad area for signs of fluid leaks.

Inspect the bushings, cable terminations and control wiring for evidence of defects in insulation integrity, such as cracking, wear, tracking corona or overheating.

Verify proper operation of temperature indicators, alarms and fan controls.

Check and record the nitrogen blanket pressure, liquid temperature, maximum temperature and liquid level.

Inspect mechanical pressure relief device to verify it has not operated.

Verify equipment, arrester, and neutral grounds if applicable.

2. Electrical Tests

Measure insulation resistance at the appropriate test value, each winding high to low and ground, low to high and ground, and high and low to ground.

Perform a Transformer turns ratio test on all three phase and compare results to values calculated from nameplate data.

Draw a fluid sample for general lab analysis.

Perform an insulation power factor test.

Perform a winding resistance test.

All service will be conducted in accordance with manufacturer’s specifications.

A comprehensive engineering report to include findings, equipment specific test data, and recommendations will be completed and submitted to the Facilities Manager within 30 days of completion of the inspection.

All work will be conducted Tuesday thru Friday, 7:00am-4:00 pm All 12 contract personnel entering the facility will be required to pass a NCIC background check, conducted by FCC Victorville. Because of time restraints of the job a minimum of 12 contractors will be required.

Facilities Manager: D.Dittemore, Cost Center Manager

Consolidated Equipment List

Model# 0076YA6SW01S Qty: 1

Qty: 2 Fused Switches

Model# 000A1P13W90A

Qty: 3

Manufacturer: ALCAD Model# SLRF 120-25 Qty: 3 Sections

Site #1

FCI 2 B UNIT

ASSET # T-H3-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL# 000D3A64K24A

SERIAL# CP0237003098

ASSET# SWGEAR-H3-01-VIX (4 section) DESCRIPTION: SWITCHGEAR (section 1)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33845G16

SERIAL# SM01A996G01

DESCRIPTION: SWITCHGEAR (section 2)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A996G02

DESCRIPTION: SWITCHGEAR (section 3)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A996G03

DESCRIPTION: SWITCHGEAR (section 4)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33845G16

SERIAL#SM01A996G04

Site #2

FCI 2 D UNIT

ASSET# T-H2-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000D3A64K24A

SERIAL#CP0237003099

ASSET# SWGEAR-H2-01-VIX (4 section) DESCRIPTION: SWITCHGEAR (section 1)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33845G16

SERIAL#SM01A995G01

DESCRIPTION: SWITCHGEAR (section 2)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A995G02

DESCRIPTION: SWITCHGEAR (section 3)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A995G03

DESCRIPTION: SWITCHGEAR (section 4)

MANUFACTURER: CUTLER HAMMER

SERIAL#SM01A995G04

Site #3

FCI 2 F UNIT

ASSET# T-H1-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000D3A64K24A

SERIAL#CP0237003100

ASSET# SWGEAR-H1-01-VIX (4 section) DESCRIPTION: SWITCHGEAR (section 1)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33845G16

SERIAL#SM01A994G01

DESCRIPTION: SWITCHGEAR (section 2)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A994G02

DESCRIPTION: SWITCHGEAR (section 3)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A994G03

DESCRIPTION: SWITCHGEAR (section 4)

MANUFACTURER: CUTLER HAMMER

SERIAL#SM01A994G04

Site #4

FCI 2 FOOD SERVICE

ASSET# T-FS-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000D3A64K24A

SERIAL#CP0126002262

ASSET# SWGEAR-FS-01-VIX (4 section) DESCRIPTION: SWITCHGEAR (section 1)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33845G16

SERIAL#SM01A992G01

DESCRIPTION: SWITCHGEAR (section 2)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A992G02

DESCRIPTION: SWITCHGEAR (section 3)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A992G03

DESCRIPTION: SWITCHGEAR (section 4)

MANUFACTURER: CUTLER HAMMER

SERIAL#SM01A992G04

Site #5

FCI 2 UNICOR

ASSET# T-UF-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000D3A64K24A

SERIAL#CP0126002261

ASSET# SWGEAR-UF-01-VIX (4 section) DESCRIPTION: SWITCHGEAR (section 1)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33845G16

SERIAL#SM01A991G01

DESCRIPTION: SWITCHGEAR (section 2)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A991G02

DESCRIPTION: SWITCHGEAR (section 3)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A991G03

DESCRIPTION: SWITCHGEAR (section 4)

MANUFACTURER: CUTLER HAMMER

SERIAL#SM01A991G04

Site #6

FCI 2 VOCATIONAL TRAINING

ASSET# T-VT-01-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000J2P11K36A

SERIAL#CP0137019338

ASSET# SWGEAR-VT-01-VIX (4 section) DESCRIPTION: SWITCHGEAR (section 1)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33845G16

SERIAL#SM01A988G01

DESCRIPTION: SWITCHGEAR (section 2)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A988G02

DESCRIPTION: SWITCHGEAR (section 3)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A988G03

DESCRIPTION: SWITCHGEAR (section 4)

MANUFACTURER: CUTLER HAMMER

SERIAL#SM01A988G04

Site #7

FCI 2 SPECIAL HOUSING

ASSET# T-SH-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000D3A64K24A

SERIAL#CP0137019334

ASSET# SWGEAR-SH-01-VIX (4 section) DESCRIPTION: SWITCHGEAR (section 1)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33845G16

SERIAL#SM01A993G01

DESCRIPTION: SWITCHGEAR (section 2)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A993G02

DESCRIPTION: SWITCHGEAR (section 3)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A993G03

DESCRIPTION: SWITCHGEAR (section 4)

MANUFACTURER: CUTLER HAMMER

SERIAL#SM01A993G04

Site #8

FCI 2 ADMINISTRATION

ASSET# T-AO-02-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000J2P11K36A

SERIAL#CP0137019342

ASSET# T-AO-03-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000J2P11K36A

SERIAL#CP0137019341

ASSET# SWGEAR-AO-01-VIX

DESCRIPTION: SWITCHGEAR (1 Section)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A986G01

ASSET# SWGEAR-AO-02-VIX

DESCRIPTION: SWITCHGEAR (1 Section)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A968G01

Site #9

FPC CENTRAL ADMIN BUILDING

ASSET# T-CA-02-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#V45M28F30LS42

SERIAL#CP0137019339

ASSET# T-CA-03-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#V45M28F30LS42

SERIAL#CP0137019340

ASSET# SWGEAR-CA-01-VIX

DESCRIPTION: SWITCHGEAR (1 Section)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A989G01

ASSET# SWGEAR-CA-02-VIX

DESCRIPTION: SWITCHGEAR (1 Section)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A998G01

Site #10

FCI 2 POWERHOUSE LOAD BANK

ASSET# T-UP-03-VIX

DESCRIPTION: TRANSFORMER (DRY TYPE)

MANUFACTURER: HAMMOND POWER

MODEL#159302

SERIAL#DB02F23

ASSET# SWGEAR-UP-02-VIX

DESCRIPTION: SWITCHGEAR (1 Section)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM02A465G01

ASSET# LDBNK-UP-01-VIX

DESCRIPTION: LOAD BANK

MANUFACTURER: ALCAD

MODEL#SLRF 120-25

SERIAL#282

Site #11

FCI 2 POWERHOUSE

ASSET# T-UP-01-VIX

DESCRIPTION: TRANSFORMER (DRY TYPE)

MANUFACTURER: CUTLER HAMMER

MODEL#MSN 02060

SERIAL#D S05007001

ASSET# SWGEAR-UP-03-VIX (2 Section) DESCRIPTION: SWITCHGEAR (section 1)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A990G01

DESCRIPTION: SWITCHGEAR (section 2)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A990G02

ASSET# HVLTDISP-UP-01-VIX (14 Sections)

DESCRIPTION: HIGH VOLTAGE DISTRIBUTION

MANUFACTURER: CUTLER HAMMER

MODEL#VCP-WSWGR

SERIAL#29949

DESCRIPTION: HIGH VOLTAGE BREAKERS (18 Breakers)

MANUFACTURER: CUTLER HAMMER

MODEL# 150VCP-W500

SERIAL#01097695, 01097543, 01097609, 01097556, 01097698, 01097696,

01107780, 01097796, 01107795, 01107805, 01107807, 01107801, 01097612, 02050538, 02050548, 01107794, 01107792, 01107803

DESCRIPTION: HIGH VOLTAGE RELAYS

MANUFACTURER: CUTLER HAMMER

MODEL# G5N1H0

SERIAL#H00215985, H00215986, H00215987, H00215988, H00215989

MODEL# BE1GPS100 E4N1H0

SERIAL#H00215990 (REV F), H00215991 (REV F)

DESCRIPTION: DIFFERENTIAL RELAY

MODEL# BE1-87G

SERIAL#H00214739, H00214740

Site #12

UNICOR PBW

ASSET# T-

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000L9P12K83A

SERIAL#CP0650014514

Site #14

FCI 1 OUTSIDE POWERHOUSE

ASSET# HVLS GL-CP-VIX

DESCRIPTION: HIGH VOLTAGE SWITCH

MANUFACTURER: SCOTT ENGINEERING

MODEL# 140437-0

SERIAL#101

ASSET# T-CP-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000A0A65W67S

SERIAL#986000615

ASSET# ET-CP-VIX (2 Section)

DESCRIPTION: EMERGENCY TRANSFORMER

MANUFACTURER: COOPER POWER

MODEL#0076YA6SW01S

SERIAL#986000635

Site #15

FCI 1 POWERHOUSE

ASSET# HVLTDISP-CP-01-VIX (10 Sections)

DESCRIPTION: HIGH VOLTAGE DISTRIBUTION

MANUFACTURER:RSE-SIERRA

MODEL#

SERIAL#11886-1

Site #16

WATERTOWER #1

ASSET# HVLS-WT1-VIX

DESCRIPTION: HIGH VOLTAGE DISTRIBUTION

MANUFACTURER: SCOTT ENGINEERING

MODEL#140436-0

SERIAL#206

ASSET# T-WT-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000E0P07W42A

SERIAL#9937017574

Site #17

EDISON YARD

ASSET# (3 Sections)

DESCRIPTION: FCI 2 SWITCHGEAR

MANUFACTURER: CUTLER HAMMER

MODEL#VACCLAD-W

SERIAL#72YE790

DESCRIPTION: CIRCUIT BREAKER

MANUFACTURER: CUTLER HAMMER

MODEL#150VCP-W500

SERIAL#01107793

ASSET# (3 Sections)

DESCRIPTION: USP SWITCHGEAR

MANUFACTURER: CUTLER HAMMER

MODEL#VACCLAD-W

SERIAL#72YE612

DESCRIPTION: CIRCUIT BREAKER

MANUFACTURER: CUTLER HAMMER

MODEL#150VCP-W500

SERIAL#01107787

ASSET# (4Sections)

DESCRIPTION: FCI 1SWITCHGEAR

MANUFACTURER: RSE-SIERRA

MODEL#

SERIAL#13344-1

Site #20

FPC FOOD SERVICE

ASSET# T-CC3-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#0034WA64W75S

SERIAL#986000670

ASSET# HVLS CC3-VIX

DESCRIPTION: HIGH VOLTAGE SWITCH

MANUFACTURER: SCOTT ENGINEERING

MODEL#140436-0

SERIAL#204

Site #21

FPC HOUSING UNIT

ASSET# T-A4-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#00A9P13W21A

SERIAL#986000742

ASSET# HVLS A4-VIX

DESCRIPTION: HIGH VOLTAGE SWITCH

MANUFACTURER: SCOTT ENGINEERING

MODEL#140436-0

SERIAL#205

Site #22

USP OUTSIDE POWERHOUSE

ASSET# T-M1-04-VIX

DESCRIPTION: TRANSFORMER (DRY TYPE) (2 Section)

MANUFACTURER: HAMMOND POWER

MODEL#159302

Site #23

USP OUTSIDE POWERHOUSE

ASSET# T-M1-01-VIX

DESCRIPTION: TRANSFORMER (DRY TYPE) (4 Section)

MANUFACTURER: CUTLER HAMMER

MODEL#MSN 01946

SERIAL#D S04154001

ASSET# SWGEAR-M1-02-VIX (2 Section) DESCRIPTION: SWITCHGEAR (section 1)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A443G01

DESCRIPTION: SWITCHGEAR (section 2)

MANUFACTURER: CUTLER HAMMER

MODEL#1A33841G16

SERIAL#SM01A443G02

ASSET# HVLTDISP-M1-01-VIX (14 Sections)

DESCRIPTION: HIGH VOLTAGE DISTRIBUTION

MANUFACTURER: CUTLER HAMMER

MODEL#VCP-WSWGR

SERIAL#29570

DESCRIPTION: HIGH VOLTAGE BREAKERS (18 Breakers)

MANUFACTURER: CUTLER HAMMER

MODEL# 150VCP-W500

SERIAL#01087368, 01087301, 01087358, 01087299, 01087266, 01076785, 01087302, 01087300, 01087372, 01087311, 01087320, 01076791, 01087370, 01076753, 01076767, 01076783, 01076794, 01076788

DESCRIPTION: HIGH VOLTAGE RELAYS

MANUFACTURER: CUTLER HAMMER

MODEL#E4NH0N

SERIAL#H00204645

MODEL#G5N1H0

SERIAL#H00207322, H00207323, H00207324

MODEL#BE1GPS100 E4N1H0

SERIAL#H00204012 (REV F), H00204013 (REV F)

Site #23

USP OUTSIDE POWERHOUSE

(CONT)

DESCRIPTION: HIGH VOLTAGE RELAY

MANUFACTURER: CUTLER HAMMER

MODEL#BE1-851

SERIAL#E00797748

DESCRIPTION: DIFFERENTIAL RELAY

MANUFACTURER: CUTLER HAMMER

MODEL#BE1-87G

SERIAL#H00214126, H00214127

Site #36

FCI 1 ADMINISTRATION

ASSET# T-B-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000A1P12W89A

SERIAL#989002768

ASSET# HVLS BCD-VIX

DESCRIPTION: HIGH VOLTAGE SWITCH

MANUFACTURER: SCOTT ENGINEERING

MODEL#140437-0

SERIAL#102

Site #37

FCI 1 HEALTH SERVICES

ASSET# T-K-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000A1P11W88A

SERIAL#989002712

ASSET# HVLS-K-VIX

DESCRIPTION: HIGH VOLTAGE SWITCH

MANUFACTURER: SCOTT ENGINEERING

SERIAL#106

Site #38

FCI 1 RECREATION

ASSET# T-O-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000A1P11W88A

SERIAL#989002711

ASSET# HVLS-O-VIX

DESCRIPTION: HIGH VOLTAGE SWITCH

MANUFACTURER: SCOTT ENGINEERING

MODEL#140436-0

SERIAL#202

ASSET# T-P-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000A0A65W67S

SERIAL#986000614

Site #39

FCI 1 FOOD SERVICE

ASSET# T-S-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000A0A65W67S

SERIAL#986000613

ASSET# HVLS-S-VIX

DESCRIPTION: HIGH VOLTAGE SWITCH

MANUFACTURER: SCOTT ENGINEERING

MODEL#140436-0

SERIAL#203

Site #40

FCI 1 FACILITIES

ASSET# T-V-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000A1P13W90A

SERIAL#989002821

ASSET# HVLS-V-VIX

DESCRIPTION: HIGH VOLTAGE SWITCH

MANUFACTURER: S&C ELECTRIC

MODEL#MANUAL PMH-9

SERIAL#051483

Site #41

FCI 1 UNIT E

ASSET# T-A3-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000A1P11W87A

SERIAL#989002934

ASSET# HVLS-A3-VIX

DESCRIPTION: HIGH VOLTAGE SWITCH

MANUFACTURER: SCOTT ENGINEERING

SERIAL#105

Site #42

FCI 1 UNIT C

ASSET# T-A2-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000A1P11W87A

SERIAL#989002933

ASSET# HVLS-A2-VIX

DESCRIPTION: HIGH VOLTAGE SWITCH

MANUFACTURER: SCOTT ENGINEERING

SERIAL#104

Site #43

FCI 1UNIT A

ASSET# T-A1-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: COOPER POWER

MODEL#000A1P11W87A

SERIAL#989002932

ASSET# HVLS-A1-VIX

DESCRIPTION: HIGH VOLTAGE SWITCH

MANUFACTURER: SCOTT ENGINEERING

SERIAL#103

Site #44

FCI 1 BLDG 1123

ASSET# T-1123-01-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: CUTLER HAMMER

MODEL#VGAE497CDK

SERIAL#10JC519460002

Site #45

FCI 1 BLDG 1119

ASSET# T-1119-01-VIX

DESCRIPTION: TRANSFORMER (OIL FILLED)

MANUFACTURER: CUTLER HAMMER

MODEL#VGAE497CDK

SERIAL#10JC519460001