Sol_140R1725Q0079_Amd_0001.pdf

(x)

140R1725Q0079 x x

1 copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted ; or (c) By separate letter or electronic communication which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGEMENT TO BE

RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN REJECTION OF YOUR

OFFER. If by virtue of this amendment you desire to change an offer already submitted , such change may be made by letter or electronic communication, provided each letter or electronic communication makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

x

R17

Grand Coulee WA 99133

PO BOX 620, MS-7810

Bureau of Reclamation, PCN

08/05/20250001

13. THIS ITEM ONLY APPLIES TO MODIFICATION OF CONTRACTS/ORDERS. IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

12. ACCOUNTING AND APPROPRIATION DATA (If required) is not extended.is extended, Items 8 and 15, and returning

Offers must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended , by one of the following methods: (a) By completing

The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offers

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

FACILITY CODE CODE

10B. DATED (SEE ITEM 13)

10A. MODIFICATION OF CONTRACT/ORDER NO.

9B. DATED (SEE ITEM 11)

9A. AMENDMENT OF SOLICITATION NO.

CODE

8. NAME AND ADDRESS OF CONTRACTOR (No., street, county, State and ZIP Code)

7. ADMINISTERED BY (If other than Item 6)CODE 6. ISSUED BY

PAGE OF PAGES

4. REQUISITION/PURCHASE REQ. NO.3. EFFECTIVE DATE2. AMENDMENT/MODIFICATION NO. 5. PROJECT NO. (If applicable)

1. CONTRACT ID CODE

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

08/05/2025

CHECK ONE A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE CONTRACT

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority) appropriation data, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(b).

E. IMPORTANT: Contractor is not is required to sign this document and return __________________ copies to the issuing office.

ORDER NO. IN ITEM 10A.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

THE PURPOSE OF THIS AMENDMENT IS TO CORRECT THE DESCRIPTION AND EXTEND THE CLOSING DATE.

A. CLIN 10 HAS BEEN REVISED TO REMOVE THE VERBIAGE "OIL SOAKED"

B. THE SOLICITATION HAS BEEN EXTENDED THROUGH 1700 PD, AUGUST 19, 2025.

ALL OTHER TERMS AND CONDITIONS APPLY.

Change Item 00010 to read as follows(amount shown is the obligated amount):

Continued ...

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)15A. NAME AND TITLE OF SIGNER (Type or print)

15C. DATE SIGNED 16B. UNITED STATES OF AMERICA 15B. CONTRACTOR/OFFEROR 16C. DATE SIGNED

(Signature of person authorized to sign) (Signature of Contracting Officer)

Paula Gross

STANDARD FORM 30 (REV. 11/2016)

Prescribed by GSA FAR (48 CFR) 53.243

Previous edition unusable

Except as provided herein, all terms and conditions of the document referenced in Item 9 A or 10A, as heretofore changed, remains unchanged and in full force and effect .

ITEM NO. SUPPLIES/SERVICES QUANTITY UNIT UNIT PRICE AMOUNT

NAME OF OFFEROR OR CONTRACTOR

2 2

CONTINUATION SHEET

REFERENCE NO. OF DOCUMENT BEING CONTINUED PAGE OF

(A) (B) (C) (D) (E) (F)

140R1725Q0079/0001

00010 G4810000480166RC 4 SE

SEAL, MECHANICAL, END SECTION, FIBRE RESIN

COMPOSITE, per the attached Bureau of Reclamation drawing 222-117-28681.

END SEAL RING SHALL COMPRISE 6 SEGMEMTS

Total outer ring Diameter: 139.025"

Total inner ring Diameter: 135.152"

Height: 2.125"

Width: 2.020"

Material: High load bearing material made from a composite aramid fabric reinforcement impregnated with a thermosetting resin.

Tensile Strength: 88 N/mm2

Compressive strength: 537 N/mm2

VARIATION ON THIS DIMENSION BETWEEN EACH COMPLETE

RING MAY BE ±0.4 TOL SPECIFIED, BUT VARIATION

BETWEEN INDIVDUAL SEGMENTS FORMING EACH RING MUST

BE WITHIN ±0.2.

VARIATION ON THIS CHORDAL DIMENSION MUST BE SUCH

THAT WHEN SEGMENTS ARE FORMED INTO A RING THE

DIAMETER DIMENSION WILL BE WITHIN THE 0.5

TOLERANCE INDICATED.

ALL DIAMETERS TO BE CONCENTRIC TO WITHIN 0.25

T.I.R.

ALL UNSPECIFIED RADII TO BE 0.75 MAXIMUM.

ALL BURRS AND SHARP EDGES REMOVED

FORT WORTH GASKET & SUPPLY PART NUMBER

725150-02-00, OR EQUAL

NSN 7540-01-152-8067 OPTIONAL FORM 336 (4-86)

Sponsored by GSA

FAR (48 CFR) 53.110