A06 Drawing.pdf

SECTION A-A

SCALE: 4X

6 INDICATED TEXT REPRESENTS PROCUREMENT

CONTRACT NUMBER AND IS PART OF

ELECTRONIC ARTWORK FILE. NUMBER IS ADDED

AFTER AWARD OF CONTRACT.

7 GROMMETS, WASHERS, AND EYELETS, ITEMS 1 ,

2 , AND 3 , ARE TO BE ATTACHED THRU TOP

SURFACE IN EACH HOLE OR SLOT SECURELY,

AFTER ENAMELING PROCESS HAS BEEN

COMPLETED. GROMMET AND EYELET FIT SHOULD

BE TIGHT AFTER INSTALLATION. DO NOT CRACK

ENAMEL COATING.

8 SUGGESTED SOURCE OF SUPPLY:

STIMPSON CO., INC.

1515 SW 13TH COURT

POMPANO BEACH, FL 33069

P/N: 0 (ZERO); C83; A516

NOTES:

1. REMOVE ALL BURRS AND SHARP EDGES.

2. DIMENSIONS IN BRACKETS ARE IN MILLIMETERS.

3. (.XXX) = DECIMAL EQUIVALENT.

4. THIS DRAWING IS TO BE USED IN CONJUNCTION

WITH USGS SPECIFICATION HIF-E-02.

5 RANGE OF STAGE TO BE SPECIFIED IN THE

PROCUREMENT CONTRACT. ELECTRONIC

ARTWORK FILE MATCHING SPECIFIED RANGE

SHALL BE SUPPLIED BY USGS/HIF. SEE

TABULATION BOX FOR RANGES. NUMBERS IN

PARENTHESES REPRESENT STAGE AT TOP END

OF EACH SECTION. THESE NUMBERS DO NOT

APPEAR ON THE STAFF GAGE SECTION.

63 [1.6] µm THIRD ANGLE PROJECTION

METRIC CONVERSION

DECIMAL [mm]

X.XX.XXX

.X X

X.X.XX

SURFACE FINISH:

ANGLES

1/16FRACTIONS

UNLESS OTHERWISE SPECIFIED DIMENSIONS

ARE IN INCHES AND INCLUDE PLATING

DECIMAL TOLERANCE [mm] = 0.13

= 1.6 = 0.8 = 0.38

.XXX .005

.XX .015

.X .030

- DO NOT SCALE THIS DRAWING -

UNITED STATES DEPARTMENT OF THE INTERIOR

GEOLOGICAL SURVEY - WATER RESOURCES DIVISION

PARTS LIST

NOTESDESCRIPTION

NO. REQ'D

APPROVALS

REVISION-DESCRIPTIONLTR. DATE

DATE

SCALE

TITLE

MATERIAL

SIZE DWG. NO. REV.

ITEM SH. QTY.

NO. SIZE DRAWING/PART NO. REQD.

DRAFTING CHECK:

DRAWN BY:

DESIGN CHECK:

DESIGN APPROVAL:

D

1/2

NIKKI DENTON

ROB MYERS

JOHNNY WHEAT

JOHNNY WHEAT

STAFF GAGE SECTIONS

STEEL, 18 GAGE (.0478) 1

0114001FULL -

8/3/10 7/11/19 7/11/19 7/11/19

REVISED AND REDRAWN

8/3/10

REVISED AND REDRAWN

AA

EYELET, OBLONG, BRASS,

.645 [16.38] X .260 [6.60] OD

2A516 3

WASHER, PLAIN, BRASS, #OW, .289 [7.34] ID8C83 2

GROMMET, ROUND, BRASS, #OG,

1/4 (.250) HOLE SIZE

80 (ZERO) 1

1.26.06 32.01.5[ ]

40.68.06 1033.31.5[ ]

.25 [6.4]

28.80.06 731.51.5[ ]

38.40.06 975.41.5[ ]

18 GAGE (.0478)

STOCK

.06/.09 [1.5/2.3]

REF - AFTER ENAMELING

REF

REF

.38 [9.7]

.19 [4.8]

19.20.06 487.71.5[ ]

TOP SURFACE

FULL R

.30 [7.6]

8X Ø"N" (.302) DRILL THRU

.25 [6.4]

.37 [9.5] REF

.37 [9.5] REF

.87 [22.1]

REF

1.37 [34.7]

REF

4.00.06 101.61.5[ ]

.18 [4.6]

.24 [6.1]168X

1.20 [30.5]

(.10 FT) REF

.090.010 2.290.25[ ]34X

.030.010 0.760.25[ ]135X 66

8-PLCS 2-PLCS

7 7

TABULATION BOX

DASH No. SECTION No. (FROM and TO) DASH No. SECTION No. (FROM and TO) DASH No. SECTION No. (FROM and TO)

-1 0.00 TO 3.32 (3.34) -11 33.96 TO 37.32 (37.34) -21 67.96 TO 71.32 (71.34)

-2 3.36 TO 6.72 (6.74) -12 37.36 TO 40.72 (40.74) -22 71.36 TO 74.72 (74.74)

-3 6.76 TO 10.12 (10.14) -13 40.76 TO 44.12 (44.14) -23 74.76 TO 78.12 (78.14)

-4 10.16 TO 13.52 (13.54) -14 44.16 TO 47.52 (47.54) -24 78.16 TO 81.52 (81.54)

-5 13.56 TO 16.92 (16.94) -15 47.56 TO 50.92 (50.94) -25 81.56 TO 84.92 (84.94)

-6 16.96 TO 20.32 (20.34) -16 50.96 TO 54.32 (54.34) -26 84.96 TO 88.32 (88.34)

-7 20.36 TO 23.72 (23.74) -17 54.36 TO 57.72 (57.74) -27 88.36 TO 91.72 (91.74)

-8 23.76 TO 27.12 (27.14) -18 57.76 TO 61.12 (61.14) -28 91.76 TO 95.12 (95.14)

-9 27.16 TO 30.52 (30.54) -19 61.16 TO 64.52 (64.54) -29 95.16 TO 98.52 (98.54)

-10 30.56 TO 33.92 (33.94) -20 64.56 TO 67.92 (67.94)

5 7 8

7 8

7 8

9.60.00 243.8.0[ ]