123-25_Bid_Document.pdf

ITB: 123-25

Wood-Chippers

REQUIREMENTS/SPECIFICATIONS

Section 1: Intent

The purpose of this invitation to bid is to establish a term contract with qualified suppliers of Wood-Chipper Units. Quantities and types of equipment to be purchased by ODOT and Political Subdivisions through this contract are undefined. Purchases will be made on an as needed basis.

Section 2: Multiple Award

ODOT will accept all responsive bids submitted on or before the specified bid opening date and make an award to all responsive bidders pursuant to O.R.C. 5513.02.

Section 3: Contract Duration

The effective duration of this contract shall be for twelve (12) months from the Date of Award.

Section 4: Free on Board (F.O.B.) Destination

The net unit bid price shall include delivery charges, Free on Board (F.O.B.) to any of ODOT’s twelve (12) Districts and eighty-eight (88) county destination locations in the State of Ohio, as per the enclosed map: NOTE: Purchase orders when issued, will detail specific destination points.

District 1 - Lima District 7 - Sidney

District 2 - Bowling Green District 8 - Lebanon

District 3 - Ashland District 9 - Chillicothe

District 4 - Akron District 10 - Marietta

District 5 – Jacksontown District 11 – New Philadelphia

District 6 – Delaware District 12 – Garfield Heights

Central Garage – Columbus (CG) OPI/CCI – Chillicothe

Section 5: Delivery

Delivery of the vehicle(s) will be F.O.B. Destination to the ship to address listed on the purchase order (this includes Co-Op) locations.

Delivery shall be required to be completed within 90 calendar days of receipt of valid Purchase Order.

5.1: Delivery Hours

All deliveries made to a Department of Transportation facility must be made between the hours of 8:00 a.m. and 2:30 p.m., Monday through Friday, unless special permission is granted by the Department to temporarily waive or adjust this requirement.

5.2: Fuel

Each unit must be delivered with a full tank of fuel & DEF, if applicable.

Section 6: Purchase Orders

The awarded vendor must be able to accept purchase orders for new units throughout the entire duration of the contract.

Section 7: Invoicing

In order to streamline the invoice payment process, the Office of Equipment Management requires vendors to email an attached copy of the invoice to the following address:

dot.cen.oem@dot.ohio.gov. The invoice is to be sent on the date that the ordered commodity is delivered to the Department.

Paper invoice to be mailed to the “Bill To” contact and address located on the purchase order. If the order is processed through a credit card, the vendor will remit the invoice to the Credit Card holder’s name and address.

Section 8: Identification Number

With invoicing, provide description and serial number/vin for each commodity being built.

Section 9: Certificate of Title or Certificate of Origin

Certificate of Title or Certificate of Origin to be furnished within thirty (30) days after delivery of the equipment. Title to be filed in Franklin County and made out to: State of Ohio, Department of Transportation, 1620 West Broad Street, Columbus, Ohio 43223.

Delivery will not be considered complete unit the title is received by Department.

Section 10: Dealers and Service

It will be the responsibility of the awarded vendor/manufacturer to provide a list of authorized on-site service providers or authorized dealers in the State of Ohio to provide warranty and service repair.

Section 11: Options List

All bidders are highly recommended to provide a complete manufacturer’s options list for the make and model bid. If ODOT plans to purchase a piece of equipment with an option that you had not bid, it could exclude you from consideration for that specific purchase.

This shall be included on pricing page excel options sheet.

Section 12: Descriptive Literature

Bidders are required to submit with their bids, the latest literature that fully describes the units being bid. The Department may, at its own discretion, find a bid non-responsive for failure to submit this descriptive literature. Bidders shall submit this literature in both a hard copy and electronic format to ensure that this requirement is fully met.

By signing and submitting a bid for this solicitation, the bidder is certifying that the make and models of all items bid herein are the latest and most current manufacturers’ models and will include the manufacturer’s latest engineering changes.

Section 13: Trade-in

The Ohio Department of Transportation reserves the right to offer used, operational equipment as trade-ins. Dealerships will be required to provide estimated trade-in values at the time a specific vehicle quotation is requested. Freight for the trade vehicle to the dealership will be FOB ODOT location and included in the freight charge for the new vehicle. At the time of delivery, dealerships have the right to re-evaluate the estimated trade in value. The Administrator of the Office of Equipment Management reserves the right to reject or refuse any trade-in allowances offered if it is determined by ODOT that refusal will be in ODOT’s best interest.

Quoted trade-in values must be held firmly. The only exception would be if damage occurred to the equipment being traded-in after the quotations have been accepted by ODOT. This change in the quotation must be preapproved by ODOT before the used equipment is transferred to the vendor. It is ODOT’s responsibility to notify the awarded vendor of any damage that has occurred after the award.

Section 14: Fluids & Lubricants

Vendor must fill out “FLUIDS & LUBRICANTS” tab to the manufacture’s standard recommendation. Must fill out accordingly to the equipment being bid through this contract.

The vendor may add more rows & columns if there are more fluids or lubricants not covered in the spreadsheet.

Section 15: Price Change

All bid pricing shall not increase for the first sixty (60) calendar days after the date of the bid opening. Thereafter, a request for a price increase may be submitted in writing to the Department’s Office of Contract Sales along with all documentation that supports the need for the price increase. No price increase will be effective until it is approved by the Department and the Vendor is notified of such approval in writing. The price increase will take effect upon the date the Vendor is notified. In the event that a price increase is accepted by the Department, the Vendor may not seek an additional price increase for at least thirty (30) calendar days. The Department reserves the right to reject any proposed price increase, or to cancel the contract if such action is determined to be in the best interest of the Department.

In the event of a general price decrease, the Department shall be guaranteed full benefit of the price reduction for all undelivered purchase orders on the effective date of the decrease and thereafter. The Department will be entitled to a price decrease any time the Vendor sells a product or a service to any similarly situated customer for less than the price agreed to between the Department and the Vendor under this Contract. Any time the Vendor sells a product or provides a service to any customer or dealer for less than it is available to the Department under this Contract, the Vendor must notify the Department of that event within thirty (30) calendar days of its occurrence and immediately reduce the price of the affected goods or services to the Department under this Contract. If the Department believes it is appropriate, it will ask to renegotiate the price under this Contract of the goods and services affected by the general reduction in price. If the Vendor and the Department cannot agree on a renegotiated price, the Department will have the right, upon notice to the Vendor, to immediately remove the affected products and services from this Contract.

Section 16: Product Specifications

All parts not specifically mentioned, which are necessary to provide a complete unit, or normally furnished as standard equipment shall be furnished. The parts shall conform in strength, quality of material and workmanship to what is normally provided in the industry.

This equipment must meet ALL Federal and State regulations.

The signing of this bid shall be considered a certification that the model as bid herein is the latest current model and will include the manufacturer’s latest engineering changes.

The Ohio Department of Transportation will consider performance history of similar equipment, vendor’s service and vendor’s overall responsiveness to the Department of Transportation’s utility of the products.

The Bidder of the equipment which is considered for award shall, at the request of the Ohio Department of Transportation, demonstrate the equipment at a location chosen by the Department Personnel to prove any feature or performance capabilities which may be in question. Should the Demonstration Equipment fail to meet Department requirements, the equipment shall be adjudged as non-conforming to bid specifications. Any equipment failing to meet the Department’s requirements/specifications, set forth in this bid document, can be removed from the contract at any time.

Compliance check boxes: Located to the right of each minimum specification are the “Comply or Don’t Comply” check boxes. Check the Comply Box if the equipment being bid meets or exceeds the minimum specifications. If the equipment does not meet or exceed the department’s minimum specifications, then the bidder must check the Don't Comply box and supply an explanation, on the ODOT excel pricing tab called “EXCEPTION”, for the non-compliant specification. The department has the right to review the “Don’t Comply” explanation and make a decision to accept or deny the equipment being bid. The bid package will be determined non-compliant and rejected by ODOT if the bidder fails to check either a Comply or Don't Comply box for each and every line of the specification being bid. This section is located in the ODOT supplied excel pricing spreadsheet, on the “SPECIFICATIONS” tab.

All other remarks, comments, etc. that are not check marks located in the check boxes will deem the vendor non-compliant.

(Specifications are located in the excel pricing sheet)

Section 17: Ohio buys information

Vendors must submit their Bid Responses electronically in OhioBuys before the published deadline date & time, Columbus, Ohio local time on the Proposal due date. Vendors will not be able to submit Bid Responses, or unsolicited Proposal amendments after the deadline.

Vendors must allow adequate time for uploading a Bid Response prior to the due date and time.

ODOT recommends that vendors submit Bid Responses as early as possible. If a second round is issued for any reason, vendors must resubmit their bid if they had already submitted in a previous round, as the previously submitted Bid Responses do NOT carry over to the new round.

The Signature process takes place after the award now. The email will come from documents@esign.ohio.gov and will go to the signatory that was identified in the bid submission.

The subject line will be the bid # Signature Request, (example: 101G-25 Signature Request).

No contract can be issued to your company until we receive your signature to complete the process. And you must have an OAKS Payor ID before a contract can be issued. To obtain that, you will need to go into https://ohiopays.ohio.gov.

ATTACHMENT A – Ohio DOT Trailer Lighting & Wiring Standard and Specifications

ODOT will only purchase trailers that meet the following lighting and wiring specifications (Reference Drawing):

Trailer shall meet or exceed all current Federal Motor Carrier Safety Regulations 393.9 thru 393.33.

Trailer cord plug shall meet SAE spec. J560 and be wired directly to trailer cord with no adaptors.

Plug to be wired as follows (no other plug wiring will be accepted):

o White – Ground return to towing vehicle o Black – Electric break controller – or not utilized if trailer has air, hydraulic or no brakes o Yellow – Left turn signal and on some light duty tow vehicles, stop/hazard lamps o Red – Stop lamps and antilock device o Green – Right turn signal and on some light duty tow vehicles, stop/hazard lamps o Brown – Clearance, marker, license plate and tail lights o Blue – If air Brake – Continuous ABS power – If electric Brake – Ing. Controlled B+ for break-away battery charge maintenance circuit

No adapters will be accepted.

Trailer cord to be wired to a weatherproof, 7-terminal junction block (Waytek part #47290 or approved equal).

All trailer light wiring (including ground wiring) must be routed to junction block.

Wire splices will be done with heat shrink butt connectors or soldered with heat-shrink.

No wire nuts, closed end connectors or self-stripping displacement connectors (i.e. Scotch Loks).

All lights to be LED. There shall be individual brake (2 ea.) and turn signal lights (2 ea.) for a total of 4 lights. These lights shall be 4” Round lights in rubber grommets or 3”x7” oval lights in rubber grommets. Clearance and Marker lights shall be 2” round lights in rubber grommets or ODOT approved equal.