1-Pavement_Technology__Inc._-_Submittals.pdf

RECLAMITE® SUBMITTALS

Forest Trail, Halsey Boulevard, Patterson Avenue, South Rhett Avenue, Shadowmoss Parkway, Algon Quin Road, Queen Street, Wingo Way

Determine the Dynamic Shear Rheological properties at 60° C of the recovered asphalt binder from the top 3/8-inch layer of each core. These properties include viscosity, phase angle, complex, elastic and viscous moduli.

The top 3/8-inch of each core was removed for testing. The asphalt was extracted and recovered as prescribed by California Test Method 365.

Viscosity and phase angle, as well as, complex, elastic and viscous moduli were determined on the recovered asphalt binder using Dynamic Shear Rheology as prescribed by AASHTO T315. Test results are reported by Table I.

SAFETY DATA SHEET

1. Identification

RECLAMITE® EMULSIONProduct identifier

None.Other means of identification

Asphalt RejuvenatorRecommended use

Must be diluted with water following manufacturer's recommendations.Recommended restrictions

Manufacturer/Importer/Supplier/Distributor information

Tricor Refining, LLC.Manufacturer:

P.O. Box 5877Address:

Bakersfield, CA 93388

(661) 393-711024-hour Telephone Number:

1-800-424-9300 (North America)CHEMTREC:

1-703-527-3887 (International)

2. Hazard(s) identification

Not classified.Physical hazards

Not classified.Health hazards

Not classified.Environmental hazards

Not classified.OSHA defined hazards

Label elements

None.Hazard symbol

Signal word None.

Hazard statement Not available.

Precautionary statement

Prevention Not available.

Response Not available.

Storage Not available.

Disposal Not available.

Hazard(s) not otherwise classified (HNOC)

None known.

Supplemental information Not applicable.

3. Composition/information on ingredients

Mixtures

CAS number %Chemical name Common name and synonyms

64742-52-5DISTILLATES (PETROLEUM),

HYDROTREATED HEAVY

NAPHTHENIC

<=40

64742-11-6Extracts (petroleum), Heavy Naphthenic Distillate Solvent

<=40

7732-18-5WATER <=40

N/APROPRIETARY INGREDIENTS < 5

4. First-aid measures

Move to fresh air. Call a physician if symptoms develop or persist.Inhalation

Wash off with soap and water. Get medical attention if irritation develops and persists.Skin contact

Rinse with water. Get medical attention if irritation develops and persists.Eye contact

1 / 6

Material name: RECLAMITE® EMULSION

5586 Version #: 03 Revision date: 11-03-2021 Issue date: 08-19-2021

SDS US

Rinse mouth. Do not induce vomiting without advice from poison control center. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs.

Ingestion

Direct contact with eyes may cause temporary irritation.Most important symptoms/effects, acute and delayed

Treat symptomatically.Indication of immediate medical attention and special treatment needed

Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves.

General information

5. Fire-fighting measures

Water fog. Foam. Dry chemical powder. Dry chemicals. Carbon dioxide (CO2).Suitable extinguishing media

Do not use water jet as an extinguisher, as this will spread the fire.Unsuitable extinguishing media

During fire, gases hazardous to health may be formed.Specific hazards arising from the chemical

Self-contained breathing apparatus and full protective clothing must be worn in case of fire.Special protective equipment and precautions for firefighters

Cool containers exposed to heat with water spray and remove container, if no risk is involved. Move containers from fire area if you can do so without risk.

Fire fighting equipment/instructions

Use standard firefighting procedures and consider the hazards of other involved materials.Specific methods

6. Accidental release measures

Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep upwind.

Keep out of low areas. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. For personal protection, see section 8 of the SDS.

Personal precautions, protective equipment and emergency procedures

Extinguish all flames in the vicinity.

Large Spills: Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Cover with plastic sheet to prevent spreading. Use a non-combustible material like vermiculite, sand or earth to soak up the product and place into a container for later disposal.

Absorb in vermiculite, dry sand or earth and place into containers. Prevent entry into waterways, sewer, basements or confined areas. Following product recovery, flush area with water.

Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination.

Never return spills to original containers for re-use.

Methods and materials for containment and cleaning up

Contact local authorities in case of spillage to drain/aquatic environment. Prevent further leakage or spillage if safe to do so. Do not contaminate water. Avoid discharge into drains, water courses or onto the ground.

Environmental precautions

7. Handling and storage

Avoid prolonged or repeated contact with skin. Avoid prolonged exposure. Use only in well-ventilated areas.

Precautions for safe handling

Keep away from heat and sources of ignition. Store in original tightly closed container.Conditions for safe storage, including any incompatibilities

8. Exposure controls/personal protection

Occupational exposure limits

US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) FormValueComponents Type

PEL 5 mg/m3 Mist.DISTILLATES

(PETROLEUM),

HYDROTREATED HEAVY

NAPHTHENIC (CAS

64742-52-5)

2 / 6

Material name: RECLAMITE® EMULSION

US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) FormValueComponents Type

PEL 5 mg/m3 Mist.Extracts (petroleum), Heavy Naphthenic Distillate Solvent

(CAS 64742-11-6)

US. ACGIH Threshold Limit Values FormValueComponents Type

TWA 5 mg/m3 Inhalable fraction.DISTILLATES

(PETROLEUM),

HYDROTREATED HEAVY

NAPHTHENIC (CAS

64742-52-5)

US. NIOSH: Pocket Guide to Chemical Hazards FormValueComponents Type

Ceiling 1800 mg/m3DISTILLATES

(PETROLEUM),

HYDROTREATED HEAVY

NAPHTHENIC (CAS

64742-52-5)

STEL 10 mg/m3 Mist.

TWA 350 mg/m3

STEL 10 mg/m3 Mist.Extracts (petroleum), Heavy Naphthenic Distillate Solvent

(CAS 64742-11-6)

TWA 5 mg/m3 Mist.

No biological exposure limits noted for the ingredient(s).Biological limit values

Provide adequate ventilation, including appropriate local extraction, to ensure that the defined occupational exposure limit is not exceeded.

Appropriate engineering controls

Individual protection measures, such as personal protective equipment

Wear safety glasses with side shields (or goggles).Eye/face protection

Skin protection

Chemical resistant gloves are recommended. If contact with forearms is likely wear gauntlet style gloves.

Hand protection

Wear appropriate chemical resistant clothing.Other

When workers are facing concentrations above the exposure limit they must use appropriate certified respirators.

Respiratory protection

Wear appropriate thermal protective clothing, when necessary.Thermal hazards

Keep away from food and drink. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants.

General hygiene considerations

9. Physical and chemical properties

Appearance

Liquid.Physical state

Liquid.Form

Not available.Color

Not available.Odor

Odor threshold Not available.

pH Not available.

Melting point/freezing point Not available.

Initial boiling point and boiling range

> 212 °F (> 100 °C) IBP

3 / 6

Material name: RECLAMITE® EMULSION

Flash point > 413.6 °F (> 212.0 °C)

Evaporation rate Not available.

Not available.Flammability (solid, gas)

Upper/lower flammability or explosive limits

Flammability limit - lower

Not available.

Flammability limit -upper (%)

Not available.

Explosive limit - lower

Not available.

Explosive limit - upper

Not available.

Vapor pressure Not available.

Vapor density Not available.

Relative density Not available.

Solubility(ies)

Solubility (water) Readily Dispersible

Partition coefficient (n-octanol/water)

Not available.

Auto-ignition temperature 500 °F (260 °C)

Decomposition temperature Not available.

Viscosity Not available.

Other information

Specific gravity 0.92 - 1.04

10. Stability and reactivity

The product is stable and non-reactive under normal conditions of use, storage and transport.Reactivity

Material is stable under normal conditions.Chemical stability

No dangerous reaction known under conditions of normal use.Possibility of hazardous reactions

Avoid temperatures exceeding the flash point. Contact with incompatible materials.Conditions to avoid

Strong oxidizing agents.Incompatible materials

No hazardous decomposition products are known.Hazardous decomposition products

11. Toxicological information

Information on likely routes of exposure

Inhalation Prolonged inhalation may be harmful.

Skin contact Frequent or prolonged contact may defat and dry the skin, leading to discomfort and dermatitis.

Eye contact Direct contact with eyes may cause temporary irritation.

Ingestion Expected to be a low ingestion hazard.

Symptoms related to the physical, chemical and toxicological characteristics

Not available.

Information on toxicological effects

Acute toxicity Not classified.

Prolonged skin contact may cause temporary irritation.Skin corrosion/irritation

Not classified.Serious eye damage/eye irritation

Respiratory or skin sensitization

Respiratory sensitization Not classified.

Not classified.Skin sensitization

No data available to indicate product or any components present at greater than 0.1% are mutagenic or genotoxic.

Germ cell mutagenicity

4 / 6

Material name: RECLAMITE® EMULSION

Carcinogenicity

IARC Monographs. Overall Evaluation of Carcinogenicity

DISTILLATES (PETROLEUM), HYDROTREATED HEAVY

NAPHTHENIC (CAS 64742-52-5)

3 Not classifiable as to carcinogenicity to humans.

OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)

Not regulated.

US. National Toxicology Program (NTP) Report on Carcinogens

Not listed.

This product is not expected to cause reproductive or developmental effects.Reproductive toxicity

Specific target organ toxicity

- single exposure

Not classified.

Specific target organ toxicity

- repeated exposure

Not classified.

Aspiration hazard Not classified.

Chronic effects Prolonged inhalation may be harmful.

12. Ecological information

The product is not classified as environmentally hazardous. However, this does not exclude the possibility that large or frequent spills can have a harmful or damaging effect on the environment.

Ecotoxicity

No data is available on the degradability of this product.Persistence and degradability

No data available.Bioaccumulative potential

No data available.Mobility in soil

Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component.

13. Disposal considerations

Contract with a disposal operator licensed by the Law on Disposal and Cleaning. Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Do not discharge into drains, water courses or onto the ground. Dispose in accordance with all applicable regulations.

Disposal instructions

Dispose in accordance with all applicable regulations.Local disposal regulations

The waste code should be assigned in discussion between the user, the producer and the waste disposal company.

Hazardous waste code

Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner (see: Disposal instructions).

Waste from residues / unused products

Empty containers should be taken to an approved waste handling site for recycling or disposal.

Since emptied containers may retain product residue, follow label warnings even after container is emptied.

Contaminated packaging

14. Transport information

DOT

Not regulated as dangerous goods.

IATA

Not regulated as dangerous goods.

IMDG

Not regulated as dangerous goods.

Not available.Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code

15. Regulatory information

This product is not known to be a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200.

US federal regulations

TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)

Not regulated.

CERCLA Hazardous Substance List (40 CFR 302.4)

Not listed.

5 / 6

Material name: RECLAMITE® EMULSION

SARA 304 Emergency release notification

Not regulated.

OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)

Not regulated.

SARA 302 Extremely hazardous substance

Superfund Amendments and Reauthorization Act of 1986 (SARA)

Not listed.

NoSARA 311/312 Hazardous chemical

SARA 313 (TRI reporting)

Not regulated.

Other federal regulations

Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List

Not regulated.

Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)

Not regulated.

Not regulated.Safe Drinking Water Act

(SDWA)

WARNING: This product contains a chemical known to the State of California to cause cancer.US state regulations

International Inventories

Country(s) or region Inventory name On inventory (yes/no)*

YesAustralia Australian Inventory of Chemical Substances (AICS)

YesCanada Domestic Substances List (DSL)

NoCanada Non-Domestic Substances List (NDSL)

YesChina Inventory of Existing Chemical Substances in China (IECSC)

YesEurope European Inventory of Existing Commercial Chemical Substances

(EINECS)

NoEurope European List of Notified Chemical Substances (ELINCS)

NoJapan Inventory of Existing and New Chemical Substances (ENCS)

YesKorea Existing Chemicals List (ECL)

YesNew Zealand New Zealand Inventory

YesPhilippines Philippine Inventory of Chemicals and Chemical Substances

(PICCS)

YesTaiwan Taiwan Chemical Substance Inventory (TCSI)

YesUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory

*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s) A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing country(s).

16. Other information, including date of preparation or last revision

08-19-2021Issue date

11-03-2021Revision date

Version # 03

Health: 1 Flammability: 1 Instability: 0

NFPA ratings

The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text.

Disclaimer

Physical & Chemical Properties: Multiple Properties Regulatory Information: United States Regulatory information: US federal regulations

Revision information

6 / 6

Material name: RECLAMITE® EMULSION

JOINTBOND® SUBMITTALS

The longitudinal joints in asphalt pavements are a common failure point.

When improperly maintained, they can reduce pavement longevity by as much as 40 percent. JOINTBOND® asphalt joint stabilizer protects longitudinal joints and surrounding areas by deeply penetrating the pavement and stabilizing the critical joints and adjacent areas. It is primarily for use on asphalt pavements less than one year old.

Markets

Counties

• Highway Shoulders

Compatible Substrates

• For asphalt pavements less than one year old.

Benefits

• Helps prevent cracking and separating of critical joints

• Penetrates deeply and quickly to protect against air, water and salt brine

• Will not obliterate striping and other markings

How It Works JOINTBOND longitudinal joint stabilizer was developed to inhibit the premature deterioration of construction joints by penetrating the asphalt pavement and combining with the existing asphalt binder.

As a polymerized maltene-based emulsion, JOINTBOND stabilizer extends the service life of longitudinal joints and adjacent areas in two ways:

• Improving the chemistry of the in-place asphalt binder

• Adding a physical in-depth seal to the construction joint, thereby sealing the joint and surrounding area against intrusion by air, water and salt brine

How to Apply Temperature Apply only when ambient temperature is expected to remain at or above 40°F for 12 hours.

Surface Preparation Surface must be dry with no threat of rain within 4 hours of application.

Field testing shall be performed prior to application to determine the maximum amount of material that the pavement can absorb within a 20 minute period.

Contractor shall apply various test strips ranging in length from 100-150 ft. using different rates, noting the time it takes for total absorption to occur without surface residues remaining.

Application Method/Rate JOINTBOND stabilizer must be applied by an approved applicator using a computerized distributor truck cleaned of all other materials to prevent contamination. Its recommended application rate is between 0.06 and

0.15 gallons per square yard (GSY).

JOINTBOND stabilizer shall be applied such that a uniform distribution is obtained along the longitudinal construction joint and an area from 1 to 1.5 feet on both sides of the joint.

Multiple applications may be needed on grades or super elevations prone to excessive runoff. Succeeding applications shall be made as soon as penetration of the preceding application is complete.

If significant residue remains due to misapplication or spills, a light coating of sand may be spread on the surface prior to opening the road to traffic.

Other Considerations Treated sections must be closed and free from traffic until JOINTBOND treatment is complete. Traffic control shall be conducted in compliance with all local, state and federal requirements.

Limited Warranty Pavement Technology, Inc. (PTI) warrants its products to be of the highest quality.

Refund of purchase price or replacement of product shall constitute the limit of PTI’s liability. PTI makes no other warranties, express or implied, with respect to the products or any service and disclaims all other warranties, including any warranty of merchantability and fitness for particular purpose. This limited warranty may not be modified by reps of PTI, its distributors or dealers.

Pavement Technology, Inc.

Real Science. Real Results.

800-333-6309 www.pavetechinc.com

(continued)

JOINTBOND Being Applied to Longitudinal Joint Area

Treated and Untreated Areas, 4 Years Post-Treatment

Treated Joint

Untreated Joint

JOINTBOND® asphalt joint stabilizer

© 2017 Pavement Technology, Inc. LB 352

Made and Sourced in America

800-333-6309 www.pavetechinc.com

The performance of JOINTBOND® asphalt joint stabilizer has been field tested by government agencies to verify its effectiveness in changing the viscosity values of the asphalt binder. The above test results were taken from the top 3/8” and the 3/8” to 3/4” layers of each core specimen removed separately. The asphalt binder was extracted and recovered from both layers separately by California Test Method 365. Viscosities, pascals (Pa), phase angles, and complex, elastic, and viscous moduli were determined on the recovered asphalt binder using the Dynamic Shear Rheometer as prescribed in ASHTO T316. The results cited above demonstrate that JOINTBOND® stabilizer has effectively combined with the asphalt binder to produce a more durable and longer lasting construction joint area.

Safety Guidelines Contractors shall follow all stipulated application requirements.

Manufacturer D&D Emulsions, Inc., Mansfield, OH

National Distributor Pavement Technology, Inc., Westlake, OH

Residue, %w 1 ASTM D-244 (Mod) Min. 39, Max. 44

Miscibility 2 ASTM D-244 (Mod) No Coagulation

Particle Charge ASTM D-244 Positive

Flash Point, COC °C ASTM D-92 Min. 200

Viscosity @ 60°C, cSt ASTM D-445 Min. 100, Max. 200

Asphaltenes, %w ASTM D-2006-70 Max. 1.0

Maltene Distribution Ratio (PC+A1) / (S+A2) 3 ASTM D-2006-70 Min. 0.2, Max. 0.8

PC/S Ratio 4 ASTM D-2006-70 Min. 0.5

Saturated Hydrocarbons ASTM D-2006-70 Min. 21, Max. 28

Percent Light Transmittance 5 D&D Emulsions Max. 30

Charge Positive

Monomer Ratio, Butadiene/Styrene 76/24

Solids Content, %w 63

Coagulum on 80 mesh screen (max. %w) 0.1

Mooney Viscosity of Polymer (ML 4 @ 212°F) min. 100

PH of Polymer 5.0

Weight per gallon (wet pounds @ 63% solids content) 7.94

Specifications/Testing

Emulsion

Residue From Distillation

Polymer

Property Test Method Requirements

Test Results on Recovered Binder

Treated Core B 3/8”-3/4” layer 7028 84.4 7047 685 7013

Untreated Core B Top 3/8” 8258 84.0 8279 869 8234

Untreated Core B 3/8”-3/4” layer 8251 84.2 8292 833 8250

Treated Core C 4036 85.2 4047 336 4033

Untreated Core C 8108 83.2 8129 965 8071

SAFETY DATA SHEET

1. Identification

Product identifier JOINTBOND®

Other means of identification Maltene Based Asphalt Longitudinal Joint Stabilizer

Recommended use Post Construction Asphalt Rejuvenator/Stabilizer

Recommended restrictions Follow the manufacturer’s instructions.

Manufacturer/Importer/Supplier/Distributor information

Manufacturer

Manufacturer: D & D Emulsions, Inc.

Address: 270 Park Avenue East

P.O. Box 1706

Mansfield, OH 44901

24- Hour Telephone Number:

CHEMTREC: 1-800-424-9300 (USA and Canada)

CCN794154

2. Hazard(s) identification

Physical hazards Not classified

Health hazards Not classified

Environmental hazards Not classified

OSHA defined hazards Not classified

Label elements

Signal word None

Hazard statement None

Precautionary statement Do not handle until all safety precautions have been read and understood.

Storage Store in accordance with international regulations. Store locked up.

Disposal Dispose of contents/container in accordance with local/regional/national/international regulations.

Hazard(s) not otherwise None known classified (HNOC)

Supplemental information Not applicable

3. Composition/information on ingredients

Mixtures

Chemical name Common name and synonyms CAS number %

PETROLEUM MALTENE EXTRACT (>99%) Maltene Rejuvenator N/A 60 – 65

WATER 7732-18-5 35 – 40

PROPRIETARY INGREDIENTS* N/A <5

*Designates that a specific chemical process or identity of composition has been withheld as a trade secret.

4. First-aid measures

Inhalation Move to fresh air. Call a physician if symptoms develop or persist.

Skin contact Wash off with soap and water. Get medical attention if irritation develops and persists.

Eye contact Rinse with water. Get medical attention if irritation develops and persists.

Ingestion Rinse mouth. Do not induce vomiting without advice from poison control center.

Material name: JOINTBOND SDS US

5516 Version #: 01 Issue date: 08/15/2021 1 / 6

Most important Direct contact with eyes may cause temporary irritation.

symptoms /effects, acute and delayed

Indication of immediate Treat symptomatically.

medical attention and special treatment needed

General information Ensure that medical personnel are aware of the material(s) involved and take precautions to protect themselves.

5. Fire-fighting measures

Suitable extinguishing media Water fog. Foam. Dry chemical powder. Dry chemicals. Carbon dioxide (CO2).

Unsuitable extinguishing media Do not use water jet as an extinguisher, as this will spread the fire.

Specific hazards arising from During fire, gases hazardous to health may be formed.

the chemical

Special protective equipment Self-contained breathing apparatus and full protective clothing must be worn in case of fire.

and precautions for firefighters

Fire-fighting Cool containers exposed to heat with water spray and remove container if no risk is involved.

equipment/ instructions

Specific methods Use standard firefighting procedures and consider the hazards of other involved materials.

6. Accidental release measures

Personal precautions, For personal protection, see section 8 of the SDS.

protective equipment and emergency procedures

Methods and materials for Large Spills: Stop the flow of material if this is without risk. Dike the spilled material, where this is possible. Cover containment and cleaning up with plastic sheet to prevent spreading. Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water.

Small Spills: Wipe up with absorbent material (e.g., cloth, fleece). Clean surface thoroughly to remove residual contamination.

Never return spills to original containers for re-use. For waste disposal, see section 13 of the SDS.

Environmental precautions Avoid unintentional discharge. Clean up accordingly.

7. Handling and storage

Precautions for safe handling Avoid prolonged or repeated contact with skin. Avoid prolonged exposure. Use only in well- ventilated areas.

Conditions for safe storage, Keep away from heat and sources of ignition. Store in original tightly closed container. Store away from incompatible including any incompatibilities materials (see section 10 of the SDS).

8. Exposure controls/personal protection

Occupational exposure limits

US. OSHA Table Z-1 Limits for Air Contaminants (29 CRF 1910.1000)

Components Type Value Form

SIMILAR CHEMICALS* PEL 5 mg/m3 Mist.

US. NIOSH: Pocket Guide to Chemical Hazards

Components Type Value Form

SIMILAR CHEMICALS* STEL 10 mg/m3 Mist.

TWA 5 mg/m3 Mist.

*Emulsified Reclamite is made from a sufficiently refined petroleum extract; Exposure limits based on similar but potentially insufficiently refined petroleum products.

Biological limit values No biological exposure limits noted for the ingredient(s).

5516 Version #: 01 Issue date: 08/15/2021 2/ 6

Appropriate engineering Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions.

controls If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level.

Individual protection measures, such as personal protective equipment

Eye/face protection Wear safety glasses with side shields (or goggles).

Hand protection Wear protective gloves.

Skin protection

Other Wear appropriate chemical resistant clothing.

Respiratory protection Not available

Thermal hazards Wear appropriate thermal protective clothing, when necessary.

General hygiene Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, considerations and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants.

9. Physical and chemical properties

Appearance Opaque Liquid

Physical state Liquid

Form Liquid

Color Yellow

Odor Mild Odor

Odor threshold Not available pH 4.5 – 7.2

Melting point/freezing point Not available

Initial boiling point and > 212 °F ( > 100 °C ) estimated boiling range

Flash point > 413 °F ( > 212 °C ) estimated

Evaporation rate < 1

Flammability (solid, gas) Not available

Upper/lower flammability or explosive limits

Flammability limit – lower Not available

Flammability limit - Not available upper ( % )

Explosive limit – lower Not available

Explosive limit – upper Not available

Vapor pressure Not available

Vapor density Not available

Relative density 1 g/cm3

Solubility (ies)

Solubility (water) Readily Dispersible

Partition coefficient Not available

(n-octanol/water)

Auto-ignition temperature 500 °F ( 260 °C ) estimated

Decomposition temperature Not available

Viscosity Not available

Other information

Percent volatile <63% (105 °C ) estimated

VOC (Weight %) Not applicable

5516 Version #: 01 Issue date: 08/15/2021 3/ 6

10. Stability and reactivity

Reactivity Product is stable and non-reactive under normal conditions of use, storage, and transport.

Chemical stability Material is stable under normal conditions.

Possibility of hazardous reactions No dangerous reaction known under conditions of normal use.

Conditions to avoid Avoid temperatures exceeding the flash point. Contact with incompatible materials.

Incompatible materials Strong oxidizing agents.

Hazardous decomposition products No hazardous decomposition products are known.

11. Toxicological information

Information on likely routes of exposure

Ingestion Expected to be a low or no ingestion hazard.

Inhalation No data available to indicate product or any components present at greater than 0.1% pose inhalation risk.

Skin contact No adverse effects due to skin contact are expected.

Eye contact Direct contact with eyes may cause temporary irritation.

Symptoms related to the physical, Direct contact with eyes may cause temporary irritation.

chemical and toxicological characteristics

Information on toxicological effects

Acute toxicity No data available to indicate product or any components present at greater than 0.1% pose toxicity risk.

Skin corrosion/irritation Prolonged skin contact may cause temporary irritation.

Serious eye damage/eye irritation Direct contact with eyes may cause temporary irritation.

Respiratory or skin sensitization

Respiratory sensitization No data available to indicate product or any components present at greater than 0.1% pose respiratory sensitization.

Skin sensitization This product is not expected to cause skin sensitization.

Germ cell mutagenicity No data available to indicate product or any components present at greater than 0.1% are mutagenic or genotoxic.

Carcinogenicity Not classified.

Emulsified Reclamite is made from a sufficiently refined petroleum extract that, in independent laboratory testing, contains no classified ingredients (>BDL) under

EPA 8207C or listed as known or potential carcinogenic agents per ACGIH, NTP, OSHA, IARC or California Prop 65.

US. OSHA Specifically Regulated Substances (29 CRF 1910.1001-1050): Not Listed

Reproductive toxicity This product is not expected to cause reproductive or developmental effects.

Specific target organ toxicity Not classified

- single exposure

Specific target organ toxicity Not classified

- repeated exposure

Aspiration hazard Not available; Not Expected.

Chronic effects Not available; Not Expected.

12. Ecological information

Ecotoxicity Product is not classified as environmentally hazardous.

Persistence and degradability No data available

Bioaccumulative potential No data available

Mobility in soil No data available

Other adverse effects No other adverse environmental effects (e.g., ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this product.

5516 Version #: 01 Issue date: 08/15/2021 4/ 6

13. Disposal considerations

Disposal instructions Collect and reclaim or dispose in sealed containers at licensed waste disposal site.

Local disposal regulations Dispose in accordance with all applicable regulations.

Hazardous waste code The waste code should be assigned in discussion between the user, the producer, and the waste disposal company.

Waste from residues/unused products Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner (see: Disposal instructions)

Contaminated packaging Empty containers should be taken to an approved waste handling site for recycling or disposal. Since emptied containers may retain product residue, follow label warnings even after container is emptied.

14. Transport information

DOT Not regulated as dangerous goods.

IATA Not regulated as dangerous goods.

IMDG Not regulated as dangerous goods.

Transport in bulk according to Not available

Annex II of MARPOL 73/78 and the IBC Code

15. Regulatory information

US federal regulations All components are on the U.S. EPA TSCA Inventory list.

TSCA Section 12 ( b ) Export Notification (40 CRF 707, Subpt. D) Not regulated

CERCLA Hazardous Substance List (40 CRF 302.4) Not listed

US. OSHA Specifically Regulated Substances (29 CRF 1910.1001-1050) Not listed

Superfund Amendments and Reauthorization Act of 1986 (SARA)

Hazard categories Immediate Hazard – No

Delayed Hazard – Not known

Fire Hazard – No

Pressure Hazard – No

Reactivity Hazard – No

SARA 302 Extremely hazardous substance Not listed

SARA 311/312 No

Hazardous chemical SARA 313 (TRI reporting) Not regulated

Other federal regulations

Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) list Not regulated

Clean Air Act (CAA) Section 112 ( r ) Not Regulated

Accidental Release Prevention (40 CRF 68.130) Not regulated

Safe Drinking Water Act (SDWA) Not regulated

5516 Version #: 01 Issue date: 08/15/2021 5 / 6

US state regulations

US. Massachusetts RTK – Substance List

Similar chemicals*

US. New Jersey Worker and Community Right-to-Know Act

Not regulated

US. Pennsylvania RTK – Hazardous Substances

Similar chemicals*

US. Rhode Island RTK

Not regulated

US. California Proposition 65

Similar chemicals*

*Emulsified Reclamite is made from a sufficiently refined petroleum extract. Disclosure here is not based on Emulsified Reclamite, but similar and potentially insufficiently refined petroleum products. The listing requirements of the Right to Know (RTK) legislation varies by state. All actionable information for NJ, PA, MA, CA and other states can be derived from the listing of hazardous and non-hazardous components in section 2 and 15 of this SDS.

International Inventories

Country (s) or region Inventory name On inventory (yes / no) *

Australia Australian Inventory of Chemical Substances (AICS) Yes

Canada Domestic Substances List (DSL) Yes

Canada Non-Domestic Substances List (NDSL) No

China Inventory of Existing Chemical Substances in China (IECSC) Yes

Europe European Inventory of Existing Commercial Chemical Substances Yes

(EINECS)

Europe European List of Notified Chemical Substances (ELINCS) No

Japan Inventory of Existing and New Chemical Substances (ENCS) No

Korea Existing Chemicals List (ECL) Yes

New Zealand New Zealand Inventory Yes

Philippines Philippine Inventory of Chemicals and Chemical Substances (PICCS) Yes

United States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory Yes

*A “Yes” indicates that all components of this product comply with the inventory requirements administered by the governing country(s)

A “No” indicates that one or more components of the product are not listed or exempt from this listing on the inventory administered by the governing country(s).

NFPA Ratings

Health: 0

Flammability: 0

Reactivity: 0

16. Other information, including date of preparation or last revision

Issue date 02-22-2021

Version # 01

Disclaimer The information provided in this Safety Data Sheet is correct and based upon independent laboratory testing and other information, knowledge, and belief at the date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage, transportation, disposal, and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text.

5516 Version #: 01 Issue date: 08/15/2021 6/ 6