1-015-26_ODOT_Catalog.pdf

Utility Truck Equipment, Inc.

Ohio DOT Contract

DOT015-26

Catalog and Prices

July 1, 2025

SST-40-EIH ODOT CONTRACT 015-26

UTILITY TRUCK EQUIPMENT, INC.

23893 U.S. 23 SOUTH

P.O. BOX 130

CIRCLEVILLE OH 43113

Telephone 740-474-5151 Fax 740-474-4402

40’ AERIAL UNIT

AERIAL TOWER AND ACCESSORIES

Versalift model SST-40-EIH insulated aerial tower with a maximum working height of 45', and a maximum horizontal side reach of 27’- 9”. Includes the following features and accessories:

• 24" x 30" x 42" enclosed fiberglass platform with bucket liner and cover.

• Full pressure platform mounted 3-function single handle control.

• Full pressure individual lower controls, with upper control override.

• Hydraulic platform leveling system with upper and lower tilt controls.

• Combination articulating/telescoping boom assembly.

• Upper fiberglass telescoping boom with outer boom insert.

• Articulating steel lower boom assembly with 12” insulated lower boom insert.

• ANSI category "C" insulation rating for 46KV and below.

• 360-degree continuous rotation.

• Center mount pedestal ahead of rear axle, with booms stowed to the rear.

• Two (2) vertical hydraulic outriggers between cab and body, controls at rear.

• Outrigger / boom interlock system.

• 17-gallon integral oil reservoir located in pedestal.

• 4/5 GPM open center hydraulic system.

• Pump and PTO assembly with brake interlock.

OHIO DEPARTMENT OF TRANSPORTATION CONTRACT 015-26

ODOT 015-26

• One (1) set of hydraulic tool outlets with quick connects located at platform.

• Remote engine stop/start system with upper and lower controls.

• 2-speed engine throttle system with upper, lower, and curbside rear controls.

• 12-volt emergency power system with upper and lower controls.

• Upper boom storage cradle with ratchet type tie down strap.

• Tubular rubber platform support.

• Safety harness and lanyard.

• Two (2) aerial device operator/service manuals.

• Finish paint standard white urethane.

• ANSI A92.2 data plate.

• Inclinometer each side on rear of body.

• Complete installation and testing of aerial tower and accessories.

AERIAL SERVICE BODY

Fiberglass service body, 132” long, 94” wide, with 18” deep side compartments.

Includes the following features and accessories:

• Heavy duty 6” steel body understructure.

• Body modification for installation of aerial tower.

• Stainless steel hinges and recessed two stage paddle latches.

• Steel treadplate cargo area floor.

• Spring loaded door holders on all vertical side compartment doors.

• Cable door stops on all horizontal doors.

• Automotive bulb type rubber door seals on all body doors.

• Curbside #2 access opening with steps to cargo area.

• Removable board across side access opening.

• Removable 6” rear tailboard.

• 30” full width steel treadplate rear tailshelf.

• ICC rear bumper with gripstrut step each side.

• Grab rail installed at curbside rear.

• Two (2) composite 18 x 18 x 1” outrigger pads and (2) aluminum pad holders.

• Two (2) rubber wheel chocks and holders.

• Combination ball / pintle hook, standard pintle hook or Reese receiver tube only.

• Fire extinguisher, first aid kit, and triangle reflector kit.

• Standard LED lighting package.

• LED rope lighting in each compartment with dash switch.

• Four (4) light strobe system, including two (2) LED amber strobes on posts at front of body, and two (2) amber strobe type flashers in tailshelf riser panel.

• Lighted master switch on dash.

• Electric back up alarm.

• Rear trailer receptacle: 6 pole pin, 7 pole pin, or 7 pole RV flat blades.

• Rear mud flaps.

• Standard white gelcoat finish on sideboxes.

• Complete installation of body and accessories.

STANDARD ODOT CONTRACT 132” BODY

CURBSIDE COMPARTMENTATION

First Vertical – Three (3) adjustable shelves with adjustable dividers.

Second Vertical - Gripstrut access steps to cargo area – Includes a grab handle on the rear of the # 1 compartment.

6" high recycled plastic board installed at floor level at access opening to close off cargo area.

Third Horizontal – Two (2) full length divider shelves, one (1) in center and one on bottom of compartment, each with twelve (12) adjustable dividers.

Fourth Vertical – Five (5) locking swivel material hooks, 1-3-1.

STREETSIDE COMPARTMENTATION

Full length through shelf installed in top of streetside sidebox, 10" down from top, with full width drop down access door on rear body panel.

First Vertical – Two (2) adjustable shelves with adjustable dividers.

Second Vertical - Two (2) adjustable shelves with adjustable dividers.

Third Horizontal - Full length bottom shelf with twelve (12) adjustable dividers.

Fourth Vertical - Two (2) adjustable shelves with adjustable dividers.

OPTION #33 – 108” BODY IN LIEU OF 132” BODY

Second Horizontal – Two (2) full length shelves with adjustable dividers, one (1) in center and one (1) on bottom of compartment.

Third Vertical – Five (5) swivel material hooks, 1-3-1.

with drop down access door on rear body panel.

First Vertical - Two (2) adjustable shelves with adjustable dividers.

Second Horizontal - One (1) full length shelf with adjustable dividers, installed on bottom of compartment.

Third Vertical - Five (5) swivel material hooks, 1-3-1.

STANDARD UNIT PRICE .......................................................................... $123,303.00.

CONTRACT DISCOUNT .......................................................................... ($10,311.00).

TOTAL F.O.B. DESTINATION ................. $112,992.00.

STANDARD UNIT OPTIONS

OPTION # PRICE EACH

1) 37' aerial tower in lieu of 40'. DEDUCT ($1,688.00)

2) Truguard 2.0 upper control dielectric system. $0.00

3) Non-insulated aerial tower in lieu of insulated. DEDUCT ($1,140.00)

4) 4-function single handle upper control ILO 3-function. $1,277.00

5) 180-degree hydraulic platform rotator. (Reduces bucket capacity by 50 lbs.) $2,436.00

6) 50 KV 24" x 30" platform liner delete. DEDUCT ($802.00)

7) 24" x 42" platform with liner and cover. (Reduces bucket capacity).

$2,112.00

8) 50KV 24" x 42" platform liner delete. DEDUCT ($928.00)

9) 24" x 30" walk-in platform with L.H. door. $1,259.00

10) Torsion bar stabilizers in lieu of outriggers. DEDUCT ($1,990.00)

11) Torsion bar stabilizers in addition to outriggers. $6,031.00

12) Hydraulic tool outlets at upper controls delete. DEDUCT ($1,176.00)

13) Hydraulic tool outlets at curbside rear under tailshelf. $1,600.00

14) Standard non-metallic colors other than white; includes tower and body.

$4,322.00

15) Ziebart rustproof chassis cab and body understructure. $1,218.00

16) Aluminum understructure with alum treadplate floor. $1,931.00

17) Aluminum treadplate cargo wall liners and comp’t tops. $1,763.00

18)

Fiberglass transverse compartment with aluminum treadplate overlay, between front verticals, with top opening lid and center shelf (front compt. Hooks 2-0-2 –

NOT AVAILABLE ON SST37 OPTION

$1,855.00

19) Pull-out drawer in bottom of transverse. $907.00

20) 18" wide through tunnel under tailshelf, door each side. $1,098.00

21)

Through shelf from horizontal to rear in top of curbside sidebox with rear door and top opening lid above horizontal compartment.

$1,075.00

22) Aluminum ladder rack assembly, installed. $1,516.00

23) #2 curbside comp’t with shelving ILO access opening. $0.00

24) Curbside tailshelf access steps ILO #2 access opening. $740.00

25) Curbside #4 access opening ILO #2 access opening. $0.00

26) Aluminum gripstrut full length of sidebox, per side. $1,284.00

27) Rod lock door system for side compartments. $793.00

28) D-ring 3-point latches in lieu of rotary latches on side compartments.

$1,762.00

29) Additional divider shelves, each. $160.00

30) One (1) pull-out 30” x 3” drawers with egg crate dividers under shelf in horizontal.

$1,233.00

31) Aluminum wheel well liners. $641.00

32) Two (2) 12-volt amber LED grille strobes. $990.00

33) Complete 60" CA package in lieu of 84" CA. DEDUCT ($160.00)

NOTES

• Requires selection of the appropriate chassis. Customer furnished chassis must meet minimum requirements for installation of equipment.

• Contact UTE to review all options available to ensure the final unit meets your specific needs. 740-474-5151

• Delivery: Approximately 400-480 days after receipt of order.

We appreciate the opportunity to assist with your equipment requirements. If you have any questions or require additional information, please contact us at your earliest convenience.

Sincerely, Jake Hill

VST-40-I ODOT CONTRACT 015-26

40’ AERIAL UNIT

Versalift model VST-40-I insulated aerial tower with a maximum working height of 45', and a maximum horizontal side reach of 30'. Includes the following features and accessories:

• 24" x 30" x 42" enclosed fiberglass platform with liner and cover.

• Full pressure individual lower controls, with upper control override.

• Hydraulic platform leveling system with upper and lower tilt controls.

• 180-degree hydraulic platform rotator system with platform mounted control.

• Combination articulating/telescoping boom assembly.

• Upper fiberglass telescoping boom with outer boom insert.

• Articulating lower boom with fiberglass insert.

• ANSI category "C" insulation rating for 46KV and below.

• 360-degree continuous rotation.

• Pedestal at the front of the cargo area, with booms stowed to the rear.

• Pedestal mounted "A" frame type main outriggers with rear controls.

• Outrigger / boom interlock system.

• 17-gallon integral oil reservoir located in pedestal.

• 6 GPM open center hydraulic system.

• Pump and PTO assembly with brake interlock.

• One (1) set of hydraulic tool outlets located at platform with pressure limit.

• Remote engine stop/start system with upper and lower controls.

• 2-speed engine throttle system with upper, lower, and curbside rear controls.

• 12-volt emergency power system with upper and lower controls.

• Upper boom storage cradle with ratchet type tie down strap.

• Tubular rubber platform support.

• Safety harness and lanyard.

• Two (2) operator/service manuals.

• Finish paint standard white urethane.

• ANSI A92.2 data plate.

• Inclinometer installed each side on rear of body.

AERIAL SERVICE BODY

Fiberglass service body, 132” long, 94” wide, with 18” deep side compartments.

• Heavy duty 6” steel body understructure.

• Body modification for installation of aerial tower.

• Stainless steel hinges and recessed two stage paddle latches.

• Steel treadplate cargo area floor.

• Spring loaded door holders on all vertical side compartment doors.

• Cable stops on all horizontal doors

• Automotive bulb type rubber door seals on all body doors.

• Curbside #2 access opening with steps to cargo area.

• Removable board across side access opening.

• Removable 6” rear tailboard.

• Outrigger cutouts in front vertical compartments.

• 30” full width steel treadplate rear tailshelf.

• ICC rear bumper with gripstrut step each side.

• Grab rail installed at curbside rear.

• Two (2) composite 18 x 18 x 1” outrigger pads and aluminum holders.

• Two (2) rubber wheel chocks and holders.

• Combination ball / pintle hook, standard pintle hook, or Reese receiver tube only.

• Fire extinguisher, first aid kit, and triangle reflector kit.

• Standard LED lighting package.

• LED rope lighting in each compartment with dash switch.

• Four (4) light strobe system, including two (2) LED amber strobes on posts at front of body, and two (2) LED amber strobe flashers in tailshelf.

• Lighted master switch on dash.

• Electric back up alarm.

• Rear trailer receptacle: 6 pole pin, 7 pole pin, or 7 pole RV flat blade.

• Rear mud flaps.

• Standard white gelcoat finish on sideboxes.

• Left rear chassis spring build up as required.

First Vertical -Two (2) adjustable shelves with adjustable dividers in upper section of compartment.

Second Vertical - Gripstrut access steps to cargo area –Includes a grab handle on the rear of the # 1 compartment.

Third Horizontal - Two (2) full length divider shelves, one (1) in center and one on

Fourth Vertical - Five (5) locking swivel material hooks, 1-3-1.

with drop down access door on rear body panel.

First Vertical - Two (2) adjustable shelves with adjustable dividers in upper section

STANDARD UNIT PRICE .......................................................................... $137,808.00.

CONTRACT DISCOUNT .......................................................................... ($10,266.00).

TOTAL F.O.B. DESTINATION .................$127,542.00.

1) 36’ VST unit in lieu of 40’. DEDUCT ($1,268.00)

2) Non-insulated aerial tower in lieu of insulated. DEDUCT ($2,085.00)

3) Truguard 2.0 upper control dielectric isolation system. $0.00

4) 4-function single handle upper control in lieu of 3-function. $1,277.00

5) Heavy duty hydraulic platform rotator and support. $1,414.00

6) Hydraulic platform elevator with HD rotator. $7,148.00

7) 50 KV 24” x 30” platform liner delete. DEDUCT ($802.00)

8) 24” x 30” walk-in platform with L.H. door. $1,259.00

9) 24” x 42” platform with liner and cover. $2,112.00

10) 50KV 24” x 42” platform liner delete. DEDUCT ($928.00)

11)

Modified A-Frame auxiliary outriggers mounted in tailshelf with rear controls. Includes interlocks, treadplate covers, and two (2) additional outrigger pads and holders.

$13,200.00

12) 24"x48" Platform with liner, cover, and additional platform rest. 600# Capacity with auxiliary rear outrigger option. $2,352.00

13) 50KV 24"x48" Platform liner delete. DEDUCT ($970.00)

14) 36” x 60” walk-in aluminum platform. $9,234.00

15) Jib and winch preparation package for hydraulic jib. $2,884.00

16) Top mount material handling winch W/ manual jib. $6,409.00

17) Top mount material handling winch W/ hydraulic jib. $10,914.00

18) Top mount material handling winch w/ dual arm hyd. jib. $11,970.00

19) Auto boom latch for support on outer boom Electroguard. $2,460.00

20) Hydraulic tool outlets at upper controls delete. DEDUCT ($1,176)

21) 4-5 GPM Hydraulic tool outlets at curbside rear of tailshelf. $1,600.00

22) Standard non-metallic colors other than white; includes tower and body. $4,322.00

23) Ziebart rustproof chassis cab and body understructure. $1,218.00

24) Aluminum understructure with alum treadplate cargo floor. $1,931.00

25) Aluminum treadplate cargo wall liners and comp’t tops. $1,763.00

26) 18” wide through tunnel under tailshelf, door each side. $1,098.00

27) Through shelf from front of horizontal to rear in top of CS sidebox. $1,075.00

28) Aluminum ladder rack assembly, installed. $1,516.00

29) #2 curbside compt. with shelving ILO access opening. $0.00

30) 15” curbside tailshelf access steps ILO #2 access opening. $740.00

31) Curbside #4 access opening in lieu of #2 access opening. $0.00

32) Aluminum gripstrut full length of sidebox, per side. $1,284.00

33) Rod lock door system for side compartments. $793.00

34) D-ring 3-point latches in lieu of rotary latches on side compts. $1,762.00

35) Additional divider shelves, each. $160.00

36) One (1) pull-out 30” x 3” drawer with criss-cross dividers under shelf in horizontal. $1,233.00

37) Aluminum wheel well liners. $641.00

38) Two (2) 12-volt amber LED grille strobes. $990.00

39) Complete 60” C.A. package in lieu of 84” C.A. DEDUCT ($160.00) must meet minimum requirements for installation of equipment.

• Contact UTE to review all options available to ensure the final unit meets your specific needs. (740)-474-5151

VST-47-I ODOT CONTRACT 015-26

P.O. BOX 130

47’ AERIAL UNIT

Versalift model VST-47-I insulated aerial tower with a maximum working height of 52', and a maximum horizontal side reach of 31'. Includes the following features and accessories:

• 24" x 30" x 42" enclosed fiberglass platform with liner and cover.

• Full pressure individual lower controls, with upper control override.

• Hydraulic platform leveling system with upper and lower tilt controls.

• 180-degree hydraulic platform rotator system with platform mounted control.

• Combination articulating/telescoping boom assembly.

• Upper fiberglass telescoping boom with outer boom insert.

• Articulating lower boom with fiberglass insert.

• ANSI category "C" insulation rating for 46KV and below.

• 360-degree continuous rotation.

• Center mount pedestal ahead of rear axle, with booms stowed to the rear.

• Four (4) hydraulic outriggers with integral full length subframe.

• Outrigger / boom interlock system.

• 17-gallon integral oil reservoir located in pedestal.

• 6 GPM open center hydraulic system.

• Transmission PTO/pump assembly with brake interlock.

• One (1) set of hydraulic tool outlets located at platform with pressure limit.

• Remote engine stop/start system with upper and lower controls.

• 2-speed engine throttle system with upper, lower, & curbside rear controls.

• 12-volt emergency power system with upper and lower controls.

• Upper boom storage cradle with ratchet type tie down strap.

• Tubular rubber platform support.

• Safety harness and lanyard.

• Two (2) operator/service manuals.

• Finish paint standard white urethane.

• ANSI A92.2 data plate.

• Inclinometer installed each side on rear of body.

• Complete installation and testing of aerial tower and accessories.

AERIAL SERVICE BODY

Fiberglass service body, 132” long, 94” wide, with 18” deep side compartments. Includes the following features and accessories:

• Heavy duty 6” steel body understructure.

• Body modification for installation of aerial tower and subframe.

• Stainless steel hinges and recessed two stage paddle latches.

• Steel treadplate cargo area floor.

• Spring loaded door holders on all side compartment doors.

• Cable stops on both horizontal doors

• Automotive bulb type rubber door seals on all body doors.

• Curbside #2 access opening with steps to cargo area.

• Removable board across side access opening.

• Removable 6” rear tailboard.

• Outrigger cutouts in front vertical compartments.

• 30” full width steel treadplate rear tailshelf.

• ICC rear bumper with gripstrut step each side.

• Grab rail installed at curbside rear.

• Four (4) composite 18 x 18 x 1” outrigger pads and aluminum holders.

• Two (2) rubber wheel chocks and holders.

• Combination ball-pintle hook, standard pintle hook, or Reese receiver tube only.

• Fire extinguisher, first aid kit, and triangle reflector kit.

• Standard LED lighting package.

• LED rope lighting in each compartment with dash switch.

• Four (4) light strobe system, including two (2) LED amber strobes on posts at front of body, and two (2) LED amber strobe flashers in tailshelf.

• Lighted master switch on dash.

• Electric back up alarm.

• Rear trailer receptacle: 6 pole pin, 7 pole pin, or 7 pole RV flat blade

• Rear mud flaps.

• Standard white gelcoat finish on sideboxes.

• Left rear chassis spring build up as required.

STANDARD 132” BODY ON ODOT CONTRACT

First Vertical – Two (2) adjustable shelves with adjustable dividers in upper section

Second Vertical - Gripstrut access steps to cargo area – Includes a grab handle on the rear of the # 1 compartment.

Fourth Vertical – Five (5) locking swivel material hooks, 1-3-1.

OPTIONAL (#26): Full length through shelf installed in top of streetside sidebox, 10" down from top, with “E” type drop down access door on rear body panel.

First Vertical – Two (2) adjustable shelves with adjustable dividers in upper section

STANDARD UNIT PRICE… .................................................................. $165,256.00.

CONTRACT DISCOUNT ...................................................................... ($14,328.00).

TOTAL F.O.B. DESTINATION… ............. $150,928.00

OPTION #21 –124” BODY IN LIEU OF 132” BODY

First Vertical - Gripstrut access steps to cargo area, with a 1" opening between the back of each step and riser panel to allow mud and ice to fall through. Includes a grab handle on the front of the # 2 compartment.

Fourth Vertical - Five (5) locking swivel material hooks, 1-3-1.

OPTIONAL (#26): Full length through shelf installed in top of streetside sidebox, 10" down from top, with “E” type drop down access door on rear body panel.

1) 4-function single handle upper control in lieu of 3-function. $1,277.00

2) Truguard 2.0 upper control dielectric isolation system. $0.00

3) Heavy duty hydraulic platform rotator and support. $1,414.00

4) Hydraulic platform elevator with HD rotator. $7,148.00

5) 50 KV 24” x 30” platform liner delete. DEDUCT ($802.00)

6) 24” x 30” walk-in platform with L.H. door. $1,259.00

7) 24” x 42” platform with liner and cover. $2,112.00

8) 50KV 24” x 42” platform liner delete. DEDUCT ($928.00)

9) 36” x 60” walk-in aluminum platform. $9,234.00

10) Jib and winch preparation package for hydraulic jib. $2,884.00

11) Top mount material handling winch W/ manual jib. $6,409.00

12) Top mount material handling winch W/ hydraulic jib. $10,914.00

13) Top mount material handling winch w/ dual arm hyd. jib. $11,970.00

14) VST-50-TN; Non-insulated aerial tower with a top mount 36” x 60” x 43” steel platform in lieu of VST-47-I. DEDUCT ($1,090.00)

15) 200# jib/winch package for VST-50-TN. $5,729.00

16) VST-52-I aerial tower in lieu of VST-47-I. $2,351.00

17) Auto boom latch for mounting on outer boom Electroguard. $2,460.00

18) 4-5 GPM Hydraulic tool outlets at curbside rear of tailshelf. $1,600.00

19) Standard non-metallic colors other than white; includes tower and body. $4,322.00

20) Ziebart rustproof chassis cab and body understructure. $1,218.00

21) 124” long body in lieu of 132”. $0.00

22) Aluminum understructure with alum treadplate cargo floor. $1,931.00

23) Aluminum treadplate cargo wall liners and comp’t tops. $1,763.00

24) 12” wide through tunnel under tailshelf, door each side. $1,089.00

25) Through shelf from horizontal to rear in top of curbside sidebox with top opening lid. $1,075.00

26) Full length hotstick shelf with “E” style door in top of streetside sidebox. $842.00

27) Aluminum ladder rack assembly, installed. $1,516.00

28) #1 or #2 curbside compt. with 3 shelves in lieu of access opening

$0.00

29) 15” Curbside tailshelf access steps in lieu of #1 or #2 access opening

$740.00

30) Curbside #4 access opening in lieu of #2 access opening. $0.00

31) Aluminum gripstrut installed full length of sidebox, per side. $1,284.00

32) Rod lock door system for side compartments. $793.00

33) D-ring 3-point latches in lieu of rotary latches on side compts.

$1,762.00

34) Additional divider shelves, each. $160.00

35) One (1) pull-out 30” x 3” drawer with criss-cross dividers

36) Aluminum wheel well liners. $641.00

37) Two (2) 12-volt amber LED grille strobes. $990.00 must meet minimum requirements for installation of equipment.

• Contact UTE to review all options available to ensure the final unit meets your specific needs. 740-474-5151

VST-5000-I ODOT CONTRACT 015-26

50’ AERIAL UNIT

Versalift model VST-5000-I insulated aerial tower with a maximum working height of 55', and a maximum horizontal side reach of 36'. Includes the following features and accessories:

• 24" x 48" x 42" enclosed fiberglass platform with liner and cover.

• Full pressure platform mounted 3-function single handle control.

• Full pressure individual lower controls, with upper control override.

• Hydraulic platform leveling system with upper and lower tilt controls.

• 180-degree hydraulic platform rotator system with platform mounted control.

• Combination articulating/telescoping boom assembly.

• Upper fiberglass telescoping boom with outer boom insert.

• Articulating lower boom with 24" fiberglass insert.

• ANSI category "C" insulation rating for 46KV and below.

• 360-degree continuous rotation.

• Pedestal at the front of the cargo area, with booms stowed to the rear.

• Pedestal mounted; Two (2) "A" frame type main outriggers with rear controls.

• Modified "A" frame auxiliary outriggers mounted in tailshelf with rear controls.

• Outrigger / boom interlock system.

• 25-gallon integral oil reservoir located in pedestal.

• 8 GPM open center hydraulic system.

• Electric shift power take off and flange mounted hydraulic pump.

• One (1) set of hydraulic tool outlets located at platform with pressure limit.

• Remote engine stop/start system with upper and lower controls.

• 2-speed engine throttle system with upper, lower, and curbside rear controls.

• 12-volt emergency power system with upper and lower controls.

• Lighted 12-volt switch panel on dash.

• Upper boom storage cradle with ratchet type tie down strap.

• Dual tubular rubber platform supports.

• Two (2) safety harnesses with lanyards.

• Two (2) operator/service manuals.

• Finish paint standard white urethane.

• ANSI A92.2 data plate.

• Inclinometer installed each side on rear of body.

AERIAL LINE BODY

Fiberglass line body, 132" long, 94" wide, with 18" deep side compartments.

Includes the following features and accessories:

• 6” steel body understructure with steel treadplate cargo area floor.

• Body modification for installation of aerial tower.

• Stainless steel hinges and recessed two stage paddle latches.

• Door holders on all vertical side compartment doors.

• Cable stops on both horizontal doors

• Automotive bulb type rubber door seals on all body doors.

• Curbside #2 access opening with steps to cargo area.

• Removable board across side access opening.

• Removable 6” rear tailboard.

• 30” full width steel treadplate rear tailshelf.

• ICC rear bumper with gripstrut step each side.

• Curbside rear grab rail.

• Four (4) composite 18” x 18” x 1” outrigger pads and aluminum holders.

• Four (4) rubber wheel chocks and holders.

• BP100A heavy duty pintle hook assembly.

• Fire extinguisher, first aid kit, and triangle reflector kit.

• Standard LED lighting package.

• LED rope lighting in each compartment with dash switch.

• Four (4) light strobe system, including two (2) LED amber strobes at front on posts at front of body, and two (2) amber strobe type flashers in tailshelf.

• Lighted master switch on dash.

• Electric back up alarm.

• Rear trailer receptacle: 6 pole pin, 7 pole pin, or 7 pole RV flat blade

• Rear mud flaps.

• Standard white gelcoat finish on sideboxes.

• Chassis spring build up as required.

STANDARD VST 5000 132” BODY ON ODOT CONTRACT

First Vertical - Five (5) swivel material hooks, 1-3-1. Hooks to be made of 1/2" round stock with 4" clear throat openings.

Second Vertical - Gripstrut access steps to cargo area, with a 1" opening between the back of each step and riser panel to allow mud and ice to fall through. Includes a grab handle on the rear of the #1 compartment.

Third Horizontal – Two (2) full length fixed divider shelves with twelve (12) adjustable dividers each, one (1) in center and one (1) on bottom of compartment.

Fourth Vertical – Two (2) adjustable shelves with adjustable dividers.

Hotstick shelf installed in top of streetside sidebox, 10" down from top, with drop down rear access door. Shelf shall include cradles equally placed along the bottom of the shelf to separate up to five (5) hotsticks.

STANDARD UNIT PRICE ......................................................................... $184,963.00.

CONTRACT DISCOUNT .......................................................................... ($9,218.00).

TOTAL F.O.B. DESTINATION .................$175,745.00.

OPTION #31 – 156” BODY IN LIEU OF 132” BODY

6" high recycled plastic board at floor level at access opening to close off cargo area.

Third Vertical - Two (2) adjustable shelves with adjustable dividers.

Fourth Horizontal - Two (2) full length fixed divider shelves with twelve (12)

Fifth Vertical - Two (2) adjustable shelves with adjustable dividers.

down rear access door.

Fourth Horizontal - Full length bottom shelf with twelve (12) adjustable dividers.

1) Truguard 2.0 upper control dielectric isolation system. $0.00

2) 4-function single handle upper control in lieu of 3-function. $1,277.00

3) 50KV 24" x 48" platform liner delete. DEDUCT ($948.00)

4) 24” x 42” x 42” platform with liner and cover. NC

5) 50KV 24” x 42” platform liner delete. NC

6) 24” x 30” walk-in platform with L.H. door. $1,259.00

7) 36” x 60” walk-in aluminum platform. $9,234.00

8) Hydraulic platform elevator with HD rotator. (Reduces platform capacity by 100 lbs.) $7,148.00

9)

Jib and winch preparation package only for use with existing customer top mount Versalift winch with hydraulic jib.

$2,844.00

10) Top mount material handling winch and manual jib. $6,409.00

11) Top mount material handling winch and hydraulic jib. $10,914.00

12) Top mount material handling winch and dual arm hyd. jib. $11,970.00

13) Auto boom latch for mounting on outer boom Electroguard. $2,460.00

14) 5 GPM Hydraulic tool outlets at curbside rear of tailshelf. $1,650.00

15) Standard non-metallic chassis colors other than white.

Includes matching color on tower and body. $5,392.00

16) Ziebart rustproof chassis cab and body understructure. $1,810.00

17) Aluminum understructure with aluminum treadplate floor. $2,745.00

18) Aluminum treadplate cargo wall liners and compt tops. $2,745.00

19) 12” wide through tunnel under tailshelf, door each side. $1,298.00

20)

Through shelf from horizontal to rear in top of curbside

$1,161.00

21) Aluminum ladder rack assembly, installed. $1,916.00

22) #2 curbside compt. with shelving in lieu of access opening. $0.00

23) Curbside tailshelf access opening in lieu of #2 access opening. $765.00

24) Aluminum gripstrut installed full length of sidebox, per side. $1,396.00

25) Rod lock door system for side compartments. $1,124.00

26) D-ring 3-point latches in lieu of rotary latches on side compts. $2,182.00

27) Additional divider shelves, each. $165.00

28) One (1) 30” x 3” pull-out drawer with criss-cross dividers under shelf in horizontal. $1,233.00

29) Aluminum wheel well liners. $673.00

30) Two (2) 12-volt amber LED grille strobes. $990.00

31)

156” long fiberglass body for 108”-120” CA in lieu of 132”/84” CA. Includes additional vertical compartment with dividers each side, ahead of rear axle.

$7,490.00 must meet minimum requirements for installation of equipment.

• Contact UTE to review all options available to ensure the final unit meets your

• Delivery: Approximately 430-520 days after receipt of order.

VST-6000-I ODOT CONTRACT 015-26

60’ AERIAL UNIT

Versalift model VST-6000-I insulated aerial tower with a maximum working height of 65', and a maximum horizontal side reach of 40'. Includes the following features and accessories:

• 24" x 48" x 42" enclosed fiberglass platform with liner and cover.

• Full pressure platform mounted 3-function single handle control.

• Full pressure individual lower controls, with upper control override.

• Hydraulic platform leveling system with upper and lower tilt controls.

• 180-degree hydraulic platform rotator system with platform mounted control.

• Combination articulating/telescoping boom assembly.

• Upper fiberglass telescoping boom with outer boom insert.

• Articulating lower boom with 24" fiberglass insert.

• ANSI category "C" insulation rating for 46KV and below.

• 360-degree continuous rotation.

• Center mount pedestal ahead of rear axle, with booms stowed to the rear.

• Four (4) hydraulic outriggers with integral full length subframe.

• Outrigger / boom interlock system.

• 25-gallon integral oil reservoir located in pedestal.

• 8 GPM open center hydraulic system.

• Electric shift power take off and flange mounted hydraulic pump.

• One (1) set of hydraulic tool outlets located at platform with pressure limit.

• Remote engine stop/start system with upper and lower controls.

• 2-speed engine throttle system with upper, lower, and curbside rear controls.

• 12-volt emergency power system with upper and lower controls.

• Lighted 12-volt switch panel on dash.

• Lower boom rest at front of body.

• Upper boom storage cradle with ratchet type tie down strap.

• Dual tubular rubber platform supports.

• Two (2) safety harnesses with lanyards.

• Two (2) operator/service manuals.

• Finish paint standard white urethane.

• ANSI A92.2 data plate.

• Inclinometer installed each side on rear of body.

AERIAL LINE BODY

Fiberglass line body, 150" long, 94" wide, with 18" deep side compartments.

• 6” steel body understructure with steel treadplate cargo area floor.

• Body modification for installation of aerial tower and subframe.

• Stainless steel hinges and recessed two stage paddle latches.

• Door holders on all vertical side compartment doors.

• Cable stops on both horizontal compartments

• Automotive bulb type rubber door seals on all body doors.

• Curbside #2 access opening with steps to cargo area.

• Removable board across side access opening.

• Removable 6” rear tailboard.

• 30” full width steel treadplate rear tailshelf.

• ICC rear bumper with gripstrut step each side.

• Curbside rear grab rail.

• Four (4) 18” x 18” x 1” composite outrigger pads and aluminum holders.

• Four (4) rubber wheel chocks and holders.

• BP100A heavy duty pintle hook assembly.

• Fire extinguisher, first aid kit, and triangle reflector kit.

• Standard LED lighting package.

• LED rope lighting in each compartment with dash switch.

• Four (4) light strobe system, including two (2) LED amber strobes on posts at front of body, and two (2) LED amber strobe type flashers in tailshelf.

• Lighted master switch on dash.

• Electric back up alarm.

• Rear trailer receptacle: 6 pole pin, 7 pole pin, or 7 pole RV flat blade.

• Rear mud flaps.

• Standard FX body white gelcoat finish on sideboxes.

• Chassis spring build up as required.

STANDARD 150” BODY ON ODOT CONTRACT

First Vertical - Five (5) swivel material hooks, 1-3-1.

Fourth Horizontal - Two (2) full length fixed divider shelves with twelve (12)

Fifth Vertical – Two (2) adjustable shelves with adjustable dividers.

First Vertical - Five (5) swivel material hooks, 1-3-1.

Fourth Horizontal - Full length bottom shelf with twelve (12) adjustable dividers.

STANDARD UNIT PRICE ......................................................................... $206,481.00.

CONTRACT DISCOUNT ...........................................................................($10,621.00).

TOTAL F.O.B. DESTINATION .................$195,860.00.

OPTION #33 – 165” BODY IN LIEU OF 150” BODY

First Vertical 25.75” - Two (2) adjustable shelves with adjustable dividers.

Second Vertical 25.25” - Gripstrut access steps to cargo area, with a 1" opening between the back of each step and riser panel to allow mud and ice to fall through.

Includes a grab handle on the rear of the #1 compartment.

Third Vertical 21.25” - Two (2) adjustable shelves with adjustable dividers.

Fourth Horizontal 53.50” - Two (2) full length fixed divider shelves with twelve (12)

Fifth Vertical 39.68” – Nine (9) swivel material hooks high as possible, 2-5-2.

First Vertical 25.75” - Two (2) adjustable shelves with adjustable dividers.

Second Vertical 19.25” - Two (2) adjustable shelves with adjustable dividers.

Third Vertical 27.25” - Two (2) adjustable shelves with adjustable dividers.

Fourth Horizontal 53.50” - Full length bottom shelf with (12) adjustable dividers.

Fifth Vertical 39.68” - Nine (9) swivel material hooks high as possible, 2-5-2.

1) VST-5500-I aerial tower in lieu of VST-6000-I. DEDUCT ($11,596.00)

2) Truguard 2.0 upper control dielectric isolation system. $0.00

3) 4-function single handle upper control in lieu of 3-function. $1,277.00

4) 50KV 24" x 48" platform liner delete. DEDUCT ($948.00)

5) 24” x 42” x 42” platform with liner and cover. NC

6) 50KV 24” x 42” platform liner delete. NC

7) 24” x 30” walk-in platform with L.H. door. $1,259.00

8) 36” x 60” walk-in aluminum platform. $9,234.00

9) Hydraulic platform elevator with HD rotator. (Reduces platform capacity by 100 lbs.) $7,148.00

10) Jib and winch preparation package only for use with existing customer top mount Versalift winch with hydraulic jib $2,844.00

11) Top mount material handling winch and manual jib. $6,409.00

12) Top mount material handling winch and hydraulic jib. $10,914.00

13) Top mount material handling winch and dual arm hyd. jib. $11,970.00

14) Auto boom latch for mounting on outer boom Electroguard. $2,460.00

15) 6 GPM Hydraulic tool outlets at curbside rear of tailshelf. $1,650.00

16) Standard non-metallic chassis colors other than white.

Includes matching color on tower and body. $5,392.00

17) Ziebart rustproof chassis cab and body understructure. $1,810.00

18) Aluminum understructure with aluminum treadplate floor. $2,745.00

19) Aluminum treadplate cargo wall liners and compt tops. $2,745.00

20) 12” wide through tunnel under tailshelf, door each side. $1,298.00

21)

Through shelf from horizontal to rear in top of curbside

$1,161.00

22)

Fiberglass transverse compartment with aluminum treadplate overlay, between front verticals, with full width top shelf. Includes vertical partition on body centerline, with three (3) pull-out drawers on curbside, and one (1) extra deep drawer on streetside. Shelf and drawers extend fully into each #1 compt.

$8,700.00

23) Aluminum ladder rack assembly, installed. $1,916.00

24) #2 curbside compt. with shelving in lieu of access opening. $0.00

25) Curbside tailshelf access opening in lieu of #2 access opening. $765.00

26) Aluminum gripstrut installed full length of sidebox, per side. $1,396.00

27) Rod lock door system for side compartments. $1,124.00

28) D-ring 3-point latches in lieu of rotary latches on side compts. $2,182.00

29) Additional divider shelves, each. $165.00

30) One (1) 30” x 3” pull-out drawer with criss-cross dividers

31) Aluminum wheel well liners. $673.00

32) Two (2) 12-volt amber LED grille strobes. $990.00

33) 165” long fiberglass body for 108” CA in lieu of 150”.

Includes larger rear verticals and extended length subframe. $6,320.00 must meet minimum requirements for installation of equipment.

• Contact UTE to review all options available to ensure the final unit meets your

• Delivery: Approximately 430-520 days after receipt of order.

60’ AERIAL TREE UNIT

Versalift model VO-260-I reverse mounted, insulated aerial tower with a maximum working height of 65', and a maximum horizontal side reach of 44'. Includes the following features and accessories:

• Standard platform capacity of 350 lbs.

• Single handle upper control with safety trigger and emergency stop valve.

• Full pressure turret mounted controls with upper control override.

• Engine stop/start at platform and lower controls.

• Lighted 12-volt switch panel on dash.

• 360-degree continuous rotation.

• 7 GPM open center hydraulic system with 2900 PSI operating pressure.

• 25-gallon integral hydraulic oil reservoir with dual sight gauges.

• Fiberglass upper boom with ANSI category “C” 46KV insulation rating.

• Lower boom fiberglass insert with 24” insulation gap.

• White gelcoat finish on fiberglass upper boom and lower boom insert.

• Appropriate height pedestal with fixed feet A-frame outriggers and controls.

• Outrigger / boom interlock system.

• Outrigger motion alarm.

• Two (2) sets of hyd. outlets at platform with disconnects.

• Upper tool circuit flow control valve.

• 24” x 24” x 42” one-man enclosed fiberglass platform with inside/outside step.

• Mechanical tilt platform for cleanout and rescue.

• 24” x 24” platform liner and vinyl platform cover.

• Safety harness and lanyard.

• Boom stow cradle and ratchet type tie down strap.

• Electric shift PTO, pump, hydraulic oil, hose, and fittings.

• Time Manufacturing standard white urethane finish.

• Two (2) sets of operators and service manuals.

• Inclinometer each side at outrigger control.

• ANSI A92.2 data plate.

DUMP CHIP BODY AND ACCESSORIES

• 132” x 60” x 96” galvanneal steel chip body with standard equipment.

• R.H. combination ladder and pole saw storage box.

• Swing to side tailgate assembly.

• LED recessed lighting package with standard back up lights.

• Hydraulic chip body hoist with control.

• 4-door wrap around tool compartment with interior hooks and shelving, and storage for long tools.

• Two (2) rubber wheel chocks with holder each side under body.

• Two (2) outrigger pad holders with 18” x 18” composite outrigger pads.

• Standard cab guard assembly.

• Access ladder assembly for access to top of cab guard and platform.

• T-60 pintle hook at rear with frame reinforcements and safety chain eyes.

• 6 and 7 pin trailer receptacles.

• Six (6) point amber led strobe package, two (2) on front of cab guard, and two

(2) each front and rear in upper corners of chip body.

• Electric trailer brake controller.

• Back up alarm at rear under chip body.

• Fire extinguisher, first aid kit, and triangle reflector kit.

• Mud flaps installed behind rear wheels.

• Complete installation of aerial tower, dump chip body, hoist, and all accessories, including mounting hardware, PTO, and hydraulic pump.

• Finish paint chip body, tool compartment, and cab guard white to match chassis cab.

• Black non-skid finish on deck section.

STANDARD UNIT PRICE.......................................................................... $157,514.00.

CONTRACT DISCOUNT ........................................................................... ($11,989.00).

TOTAL F.O.B. DESTINATION. .............. $145,525.00.

1)

VO-270E aerial tower in lieu of VO-260-I (chip body only – requires 138” CA chassis cab. This charge would apply as an add-on amount to options 7, 8, and 9 as well).

$34,819.00

2)

VO-255 rear mount aerial tower package with booms stowed to front over cab. Includes the following features in lieu of dump chip body package:

• Single handle control between boom and platform.

• Low stow upper boom for access from flatbed floor.

• 4 outriggers and subframe, outrigger controls at rear.

• 44” saddle pack with 12’ heavy duty flatbed.

• Saddle pack with transverse, shelves, and hooks.

• Treadplate floor on flatbed.

• Curbside E-Z step with grab rail for access to top of flatbed.

• Two (2) rubber wheel chocks with holder each side under body.

• Arbortech cab guard assembly.

• T-60 pintle hook assembly with safety chain eyes.

• Four (4) light strobe system.

• LED recessed lighting package with standard back up lights.

• Electric back up alarm.

• Rear trailer receptacle.

• Fire extinguisher, first aid kit, and triangle reflector kit.

• Mud flaps installed ahead of and behind rear wheels.

• Black non-skid paint applied to flatbed floor.

$16,263.00

3) 12-volt emergency power system with upper and lower controls. $2,522.00

4) 36” x 18” x 18” aluminum underbody box (with item #2 only). $1,748.00

5) 72” aluminum top box with (2) drop down doors (item #2 only). $2,665.00

6) 24” x 30” platform, liner, and cover. $1,949.00

7) Ziebart rustproof chassis cab and body understructure. $1,892.00

8) Stock RTG package F750 33K GVWR diesel automatic with standard VO260 chip body package. TOTAL UNIT PRICE

$237,653.00

9) Stock RTG package Freightliner 33K GVWR diesel automatic with standard VO260 chip body package. TOTAL UNIT PRICE

$261,520.00

10) Stock RTG package MV607 IH 33K GVWR diesel automatic with standard VO260 chip body package. TOTAL UNIT PRICE

$256,757.00

11) Deduct from stock base package for under CDL, 25,999 GVWR. ($9,967.00) must meet minimum requirements for installation of equipment.

• Delivery: Approximately 200-250 days after receipt of order. RTG units subject to availability, will generally have faster delivery.

earliest convenience.

Thank you for your consideration.

Sincerely, Utility Truck Equipment, Inc.

FORD F550 CAB AND CHASSIS

• 2026 Ford F550 4x4 chassis cab.

• XL trim package; includes keyless entry, power windows/door locks, heated mirrors.

• 169" wheelbase, 84" C.A.

• Two (2) front tow hooks.

• 6.7L diesel engine.

• 10 speed automatic transmission.

• Transmission PTO provisions.

• 19,500# GVWR payload plus upgrade package.

• Limited slip rear axle.

• Extra heavy-duty front suspension, 7,500# front GAWR.

• 4-wheel ABS hydraulic brake system.

• Speed control and telescoping steering wheel.

• Heavy duty alternator.

• Dual maintenance free batteries.

• AM/FM stereo radio with clock.

• Sync Bluetooth package.

• Engine block heater.

• 40-gallon aft axle rear fuel tank.

• Urea tank driver side inside frame rail.

• Standard interior trim.

• Vinyl 40/20/40 bench seat.

• Standard gauge cluster.

• Factory air conditioning.

• Manual telescoping trailer tow mirrors.

• LT225 radial tires, max traction tires all around.

• Ford standard oxford white paint.

• Trailer brake controller.

STANDARD UNIT PRICE ............................................................................. $81,298.00.

CONTRACT DISCOUNT ............................................................................... ($5,643.00).

TOTAL FOR F550 CHASSIS CAB. .......... $75,655.00.

STANDARD OPTIONS

1) F600 22,000# GVWR in lieu of F550 (regular cab only). $3,575.00

2) 60” C.A. in lieu of 84” C.A. DEDUCT ($160.00)

3) Extended cab in lieu of regular cab. $4,350.00

4) 4-door crew cab in lieu of regular cab. $6,288.00

5) 7.3L V-8 gasoline engine in lieu of diesel. (Comes with dual batteries and heavy-duty alternator). DEDUCT ($8,230.00)

6) Cab running board and step combination. $699.00

7) 4x2 (2-wheel drive) in lieu of 4x4. DEDUCT ($2,041.00)

8) 120V/400W outlet on dash. $195.00

9) Ford Pro Power Onboard 2kw. 120V / 2,000W outlet.

(Includes dual alternators) $2,120.00

10) Cloth 40/20/40 seat. $200.00

11) Cloth 40/20/40 seats for extended or crew cabs (add to option 12 or 15).

$835.00

12) Vinyl 40/mini console/40 seat $560.00

13) Cloth 40/mini console/40 seat. $755.00

14) XL Chrome decor package. (Chrome bumper, fog lights, remote start). $800.00

15) XLT package - includes dual alternators, transmission pto/and pump. $4,532.00

16) Stainless steel wheel covers. $560.00

17) Ford backup camera system, installed. $1,792.00

18) Additional smart key. $390.00

19) Polished Aluminum wheels. (Requires XLT package). $1,835.00

20) Deduct for deletion of chassis manuals. DEDUCT ($990.00)

• Chassis must be purchased in conjunction with contract equipment package.

We appreciate the opportunity to assist with your equipment requirements. If you have any questions or require additional information, please contact us at your earliest convenience.

DODGE 5500 CAB AND CHASSIS

• 2026 Dodge 5500 4x4 chassis cab.

• 168" wheelbase, 84" C.A.

• Two (2) front tow hooks.

• 6.7L Cummins diesel engine.

• Front hood protection shield.

• 6 speed automatic transmission.

• Power take off provisions.

• 19,500# GVWR.

• 7,500# front GAWR.

• Heavy duty front suspension.

• Anti-spin rear differential.

• 4-wheel ABS hydraulic brake system.

• Trailer brake controller.

• Cruise control and tilt steering wheel.

• Heavy duty alternator.

• Dual maintenance free batteries.

• AM/FM stereo radio with clock and Bluetooth phone connection.

• Engine block heater.

• 52-gallon aft axle rear fuel tank.

• Standard urea tank under driver side of cab.

• Standard interior trim.

• Vinyl bench seat.

• Standard gauge cluster.

• Factory air conditioning.

• Fold away trailer tow mirrors.

• LT225 radial tires, traction rear.

• Standard bright white paint.

STANDARD UNIT PRICE ............................................................................ $86,902.00.

CONTRACT DISCOUNT ............................................................................... ($7,049.00).

TOTAL FOR DODGE CHASSIS CAB ....... $79,853.00.

1) 60” C.A. in lieu of 84” C.A. (18,750# GVWR) DEDUCT ($160.00)

2)

Gas engine in lieu of diesel. DEDUCT

($6,221.00)

3)

4x2 (2-wheel drive) in lieu of 4x4. DEDUCT

($1,836.00)

4)

Traction tires all six (6) wheels on 4x4 option.

$736.00

5) 4-door crew cab in lieu of regular cab. $5,212.00

6) Tubular side steps. $994.00

7) Keyless entry, power windows and door locks, heated mirrors. $2,880.00

8) Dodge OEM camera system, installed. $2,189.00

9) 2 (two) additional smart keys with completed unit. $535.00

10) Deduct for deletion of chassis manuals. DEDUCT ($925.00)

• Chassis must be purchased in conjunction with contract equipment package.

INTERNATIONAL CV515 CAB AND CHASSIS

• 2026 International CV515 4x4 chassis cab.

• Classic interior trim package.

• 165" wheelbase, 84" C.A.

• Two (2) front tow hooks.

• 6.6L 350 HP diesel engine.

• Federal emission compliance.

• 6 speed Allison 1750RDS automatic transmission.

• Transmission PTO provisions.

• 7,500# front driving axle with 2 speed transfer case

• 19,500# GVWR package with 15,500# rear axle

• Limited slip rear axle, locker style.

• Heavy duty suspension.

• 4-wheel ABS hydraulic brake system.

• Speed control and tilt steering wheel.

• 150-amp alternator.

• Dual maintenance free batteries.

• Body builder wiring back of cab.

• Factory upgraded seat with fold down console

• AM/FM stereo radio with MP3, USB input, 6 speakers, 8.0” touch panel display.

• Bluetooth connection to radio

• Power doors, power windows and power adj.102” wide heated remote mirrors

• Trailer brake controller

• Four (4) latching dash switches.

• Body builder wiring back of cab.

• Throttle, engine speed control for PTO.

• Engine block heater.

• 40-gallon aft axle rear fuel tank.

• Urea tank passenger side under cab.

• Manual regen capability.

• Vinyl 40/20/40 seat with fold-down center console

• Standard gauge cluster.

• Factory air conditioning.

• Manual telescoping wide load mirrors.

• 225/70R19.5 radial tires, traction tread all tires.

• International standard 9219 white paint.

OHIO DEPARTMENT OF TRANSPORATION CONTRACT 015-26

STANDARD UNIT PRICE ..................................................................... $86,343.00

CONTRACT DISCOUNT ...................................................................... ($4,455.00)

TOTAL FOR CV515 CHASSIS ............... $81,888.00.

1) Chevrolet Silverado 5500 chassis in lieu of IH CV515. $528.00

2) 22,500# GVWR in lieu of 19,500# with 2750 transmission $7,645.00

3) 4-door crew cab in lieu of regular cab, 4x2 chassis. $4,650.00

4) 4-door crew cab in lieu of regular cab, 4x4 chassis. $6,826.00

5) 2-wheel drive package with electronic shift. DEDUCT ($1,600.00)

6) Cloth seats in lieu of vinyl. $987.00

7) Chrome front grille and bumper. $982.00

8) IH backup camera system, installed. $2,232.00

9) Additional smart key, (2) included with truck $389.00

10) Deduct for deletion of chassis manuals. DEDUCT ($800.00)

• Chassis must be purchased in conjunction with contract equipment package.

INTERNATIONAL MV607 CAB AND CHASSIS #1

• 2027 International MV607 4x2 chassis cab.

• 33,000# GVWR

• 156" wheelbase, 89" C.A.

• Two (2) front tow hooks.

• 120,000 PSI high strength steel frame.

• Heavy duty black steel front bumper.

• Cummins B6.7 2021 diesel engine, 280 H.P.

• Allison 3000-RDS-P 6-speed automatic transmission with PTO gear.

• Transmission programming with performance mode as primary.

• Transmission temperature gauge.

• Meritor 21,000# single speed rear axle for 75 mph.

• R series wheel ends, and driver controlled main locking rear differential.

• 23,500# rear springs with 4500# auxiliaries.

• 12,000# front axle and tapered leaf springs with auxiliary rubber springs.

• Anti-lock air brake system with dash mounted parking brake.

• Air tanks, (2) between rails

• Automatic front and rear slack adjusters.

• Manual air tank drain valve with pull chain.

• Front and rear…