HOSE, AIR BREATHING
Added: Jun 04, 2015 4:44 pm HOSE, AIR DUCT (AIR BREATHING).Size 2, low pressure, flexible hose, mustard gasresistant, nominal length 6 feetNSN 4720-00-279-0093QUANTITY 7,282 EATHIS ITEM HASTECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TOEXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATAAND ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIEDTHROUGH JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THEDEPARTMENTS OF STATEOR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO INTERNATIONAL AGREEMENTS.TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345,"MILITARYCRITICAL TECHNICAL DATA AGREEMENT," FORM IS AVAILABLE AT THE WORLD WIDE WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP OR BYWRITING TO:DLA LOGISTICS INFORMATION SERVICEFEDERAL CENTER74 WASHINGTON AVE., NORTHBATTLE CREEK, MI 49037-3084TO MANUFACTURETHIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT ACURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCEAGREEMENT,DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THEOFFER, UNLESS ANEXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 "EXEMPTIONS OFGENERAL APPLICABILITY," AND/OR EAR PART 740ARE APPLICABLE.NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICALDATA ARE REQUIRED TO PROVIDE THE CONTRACTINGOFFICER WITH ANAPPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TORECEIVE A COPY OF THE EXPORT CONTROLLEDTECHNICAL DATA.NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO THEIR DD FORM 2345 CERTIFICATION MAY NOTFURTHER DISSEMINATE SUCH DATA UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLYPERMITTED BY DODD5230.25." 52.246-11 Higher Level Contract Quality Requirement (Manufacturers)FAR CLAUSE 52.246-11 APPLIES. A QUALITYMANAGEMENT PROGRAM MEETING THEREQUIREMENTS OF ISO 9001:2008; A PROGRAM COMPARABLE TO ISO 9001:2008(EXAMPLE SAE AS 9100), THEFOLLOWING TAILORED VERSION OF ISO 9001:2008;OR A PROGRAM COMPARABLE TO THE TAILORED VERSION OF ISO 9001:2008(EXAMPLE SAE AS 9003)IS REQUIRED. MIL-I-45208 AND MIL-Q-9858 AREOBSOLETE AND NO LONGER CONSIDERED SUITABLE WHEN HIGHER LEVEL QUALITY IS REQUIRED. IN THE TAILORED VERSION OF THE ISO 9001:2008, ANY REFERENCES WHICH CITE THE ENTIRE INTERNATIONAL STANDARD ARE INTERPRETED AS EXCLUSIONS TO THIS DOCUMENT.DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:20084.1 General requirements, [excluding reference to 1.2and excluding NOTE4.2.1 General, [excluding subparagraph a)]4.2.2 Quality manual, [excluding subparagraph a)]4.2.3 Controlof documents4.2.4 Control of records5.1 Management commitment5.3 Quality policy6.2.2 Competence, training and awareness6.4 Work environment7.1 Planning of product realization, [excluding NOTE 2]7.2.1 Determination of requirements related to theproduct7.2.2 Review of requirements related to the product7.2.3 Customer communication7.4.1 Purchasing process7.4.3 Verification of purchased product7.5.1 Control of production and service provision7.5.3 Identification and traceability7.5.4 Customerproperty7.5.5 Preservation of product7.6 Control of monitoring and measuring equipment8.1 General, [excluding subparagraph b) and subparagraph c)]8.2.2 Internal audit8.2.4 Monitoring and measurement of product8.3 Control of nonconforming product8.5.2Corrective action8.5.3 Preventive actionGOVERNMENT/CONTRACTOR FAT, PACKAGING FAT andGOVERNMENT/CONTRACTOR PLT IS REQUIREDIAWSQAP002790093.DESTRUCTIVE TESTING APPLIES.The following Contract Data Requirements Lists (CDRLs), DD Form 1423s,apply tothis procurement. Review the Technical Data Package (TDP) foradditional information.Contractor First Article Test ReportProduction Lot Acceptance Test ReportCertificate of ConformanceQuality Program PlanCLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BEUSED NORINCORPORATED IN ANY ITEMS TO BEDELIVERED UNDER THIS CONTRACT.THIS PROHIBITIONSUPERSEDES ALL SPECIFICATION REQUIREMENTS BUTDOESNOT ALLEVIATE ANY PRODUCT REQUIREMENTS.SUBSTITUTE CHEMICALS MUST BE SUBMITTED FORAPPROVAL UNLESS THEY ARE AUTHORIZED BYTHESPECIFICATION REQUIREMENTS.The following Engineering Exceptions shall apply to this procurement:Drawing 81361 5-19-916-2,Product Data Management System Technical DataPackage List, Valid from 2/25/15 to 2/25/16, page 2, Drawing numberMIL-DTL-14506, REV SYM 'H' should be changed to 'J'.ANSI MH1 can be obtained on the Material Handler's of America's website,www.mhi.org, referenced simply as MH1. Standard is available at no costbut free registration on the site is required to obtain.THIS SHELF LIFE ITEM ISNON-EXTENDABLE, CODE S,WITH A TOTAL SHELF LIFE OF SIXTY MONTHS.MATERIAL FURNISHED UNDER THIS CONTRACT/ORDERSHALL HAVE AT LEAST85% (51 MONTHS) OF SHELFLIFE REMAINING AT TIME OF DELIVERY.SHELF LIFE MARKINGS REQUIRED PER 5.10.1 OFMIL-STD-129: SHELF-LIFEMARKINGS SHALL BE SHOWN ASPART OF THE ITEM IDENTIFICATION DATA ON UNIT PACKS,INTERMEDIATE CONTAINERS, EXTERIOR CONTAINERS,ANDUNPACKED ITEMS. SHELF-LIFE MARKINGS SHALL INCLUDETHE CURED DATE AND THE EXPIRATION DATE.THE EXPIRATION DATE SHALL BECALCULATED FROM THE CUREDDATE OF THE RUBBER/ELASTOMER.FULL AND OPEN COMPETITION APPLYThis is an identified Chemical Biological Defense Equipment item.All requests for waivers or deviations, both pre and post award, must beapproved by theappropriate Joint Program Executive Office for Chemicaland Biological Defense (JPEO-CBD) ESA prior to final approval.All packaged items of supply shall be marked IAW MIL-STD-129.Requirements defining levels of pack shall be IAW MIL-STD-2073-1. Ifmilitarypackaging is required and Special Packaging Instructions (SPI)are provided in the technical data package (TDP), then the packagingshall be IAW the provided SPI. CRITICAL APPLICATION ITEMIAW BASIC DRAWING NR 81361 5-19-916REVISION NR AD DTD01/22/2015PART PIECE NUMBER: C5-19-916-2IAW REFERENCE SPEC NR MIL-DTL-14506JREVISION NR J DTD 10/03/2006PART PIECENUMBER:IAW REFERENCE STD NR MIL-STD-129RREVISION NR R DTD 10/03/2006PART PIECE NUMBER: TYPE I SHELF LIFE, 60 MONTHSIAWREFERENCE NON GOVT STD ASTM D2000-12REVISION NR 12 DTD 02/14/2012PART PIECE NUMBER:IAW REFERENCE NON GOVT STD SAEAMS-QQ-W-428AREVISION NR DTD 10/07/2006PART PIECE NUMBER:IAW REFERENCE QAP 16236 SQAP002790093REVISION NR F DTD05/11/2015PART PIECE NUMBER:IAW REFERENCE DRAWING NR 81361 5-19-916-2REVISION NR DTD 02/25/2015PART PIECE NUMBER:IAWREFERENCE DRAWING NR 81361 5-19-916-2REVISION NR A DTD 04/07/2014PART PIECE NUMBER:IAW REFERENCE QAP 16236CDRL-ECBCPLTC-15062REVISION NR DTD 03/03/2015PART PIECE NUMBER:IAW REFERENCE QAP 16236 CDRL-ECBCCOC-15062REVISION NRDTD 03/03/2015PART PIECE NUMBER:IAW REFERENCE QAP 16236 CDRL-ECBCFATC-15062REVISION NR DTD 03/03/2015PART PIECENUMBER:IAW REFERENCE QAP 16236 CDRL-ECBCQPP-15062REVISION NR DTD 03/03/2015PART PIECE NUMBER:PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999QUP:001 PRES MTHD:ZZ CLNG/DRY:Z PRESV MAT:ZZWRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNNTHKNESS:ZUNIT CONT:ZZ OPI:AINTRMDTE CONT:ZZ INTRMDTE CONT QTY:ZZZPACK CODE:UMARKING SHALL BE IN ACCORDANCE WITHMIL-STD-129.SPECIAL MARKING CODE:32 -32 Type I, shelf lifePALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY01, 2008DM_15_002790093 - DATE:-12 FEB 2015NSN:4720-00-279-0093PRESERVATION: MILITARYLEVEL OF PACKING: -B--QUANTITY PERUNIT PACKAGE: -001-SPI NUMBER P5-19-916-2, Rev A, Date 7 APR 2014-PLACE A RED X AND THE WORDS"SHORT BOX" ON THE FRONT OF ANY BOXTHAT HAS A SHORT QUANTITY, THEN PLACE THAT BOX/BOXES WITH THE MARKINGS SHOWING ON THE TOP FRONT OF THE PALLET LOAD.Certificates of Conformances (see CDRL for COC format IAWDI-MISC-81356A) are required for all material and shall be submitted aspart of the First Article Test report (FATR). COC's are also requiredfor packaging materials. The contractor is responsible for allinspections and testing regardless of who conducts the actual testing.A packaging FAT is required and shall consist of tee (3) packagedunitsinspected IAW SPI P5-19-916-2.THIS SHELF LIFE ITEM IS NON-EXTENDABLE, CODE S,WITH A TOTAL SHELF LIFE OF SIXTY MONTHS.MATERIALFURNISHED UNDER THIS CONTRACT/ORDERSHALL HAVE AT LEAST 85% (51 MONTHS) OF SHELFLIFE REMAINING AT TIME OFDELIVERY.SHELF LIFE MARKINGS REQUIRED PER 5.10.1 OFMIL-STD-129: SHELF-LIFE MARKINGS SHALL BE SHOWN ASPART OF THE ITEM IDENTIFICATION DATA ON UNIT PACKS,INTERMEDIATE CONTAINERS, EXTERIOR CONTAINERS, ANDUNPACKED ITEMS. SHELF-LIFE MARKINGS SHALL INCLUDETHE CURED DATE AND THE EXPIRATION DATE.THE EXPIRATION DATE SHALL BE CALCULATED FROM THE CUREDDATE OF THERUBBER/ELASTOMER.PARCEL POST ADDRESS:W25G1UW1BG DLA DISTRIBUTIONDDSP NEW CUMBERLAND FACILITY2001 NORMANDY DRIVE DOOR 113 TO 134NEW CUMBERLAND PA 17070-5002USFREIGHT SHIPPING ADDRESS:W25G1UW1BG DLA DISTRIBUTIONDDSP NEW CUMBERLAND FACILITY2001 NORMANDY DRIVE DOOR 113 TO 134NEW CUMBERLAND PA 17070-5002US SPE7M415Q0317 Defense Logistics Agency Land and Maritime
6/4/15, 4:44 PM