Hose, air breathing

Added: Jun 04, 2015 4:44 pm HOSE, AIR DUCT (AIR BREATHING).
Size 2, low pressure, flexible hose, mustard gas
resistant, nominal length 6 feet

NSN 4720-00-279-0093

QUANTITY 7,282 EA

THIS ITEM HASTECHNICAL DATA SOME OR ALL OF WHICH IS SUBJECT TO
EXPORT-CONTROL REGULATIONS. DISTRIBUTION OF THE TECHNICAL DATA
AND ELIGIBILITY FOR AWARD ARE LIMITED TO THOSE SUPPLIERS QUALIFIED
THROUGH JCP CERTIFICATION, OR TO THOSE LICENSED BY EITHER THE
DEPARTMENTS OF STATEOR COMMERCE; OR TO FOREIGN SUPPLIERS PURSUANT TO INTERNATIONAL AGREEMENTS.

TO APPLY FOR JCP CERTIFICATION, COMPLETE DD FORM 2345,"MILITARY
CRITICAL TECHNICAL DATA AGREEMENT," FORM IS AVAILABLE AT THE WORLD WIDE WEB ADDRESS HTTP://WWW.DLIS.DLA.MIL/JCP OR BYWRITING TO:

DLA LOGISTICS INFORMATION SERVICE
FEDERAL CENTER
74 WASHINGTON AVE., NORTH
BATTLE CREEK, MI 49037-3084

TO MANUFACTURETHIS ITEM, NON-JCP CERTIFIED SUPPLIERS MUST SUBMIT A
CURRENT MANUFACTURING LICENSE AGREEMENT, TECHNICAL ASSISTANCEAGREEMENT,
DISTRIBUTION AGREEMENT OR OFF-SHORE PROCUREMENT AGREEMENT APPROVED BY THE DIRECTORATE OF DEFENSE TRADE CONTROLS WITH THEOFFER, UNLESS AN
EXEMPTION UNDER THE PROVISIONS OF ITAR SECTION, 125.4 "EXEMPTIONS OF
GENERAL APPLICABILITY," AND/OR EAR PART 740ARE APPLICABLE.

NON-JCP CERTIFIED SUPPLIERS SEEKING EXPORT CONTROLLED TECHNICAL
DATA ARE REQUIRED TO PROVIDE THE CONTRACTINGOFFICER WITH AN
APPLICABLE AGREEMENT OR IDENTIFY WHICH ITAR/EAR EXEMPTION APPLIES TO
RECEIVE A COPY OF THE EXPORT CONTROLLEDTECHNICAL DATA.

NOTE: JCP CERTIFIED CONTRACTORS WHO RECEIVE TECHNICAL DATA PURSUANT TO THEIR DD FORM 2345 CERTIFICATION MAY NOTFURTHER DISSEMINATE SUCH DATA UNLESS FURTHER DISSEMINATION OF THE TECHNICAL DATA IS EXPRESSLY
PERMITTED BY DODD5230.25."

 52.246-11 Higher Level Contract Quality Requirement (Manufacturers)

FAR CLAUSE 52.246-11 APPLIES. A QUALITYMANAGEMENT PROGRAM MEETING THE
REQUIREMENTS OF ISO 9001:2008; A PROGRAM COMPARABLE TO ISO 9001:2008
(EXAMPLE SAE AS 9100), THEFOLLOWING TAILORED VERSION OF ISO 9001:2008;
OR A PROGRAM COMPARABLE TO THE TAILORED VERSION OF ISO 9001:2008
(EXAMPLE SAE AS 9003)IS REQUIRED. MIL-I-45208 AND MIL-Q-9858 ARE
OBSOLETE AND NO LONGER CONSIDERED SUITABLE WHEN HIGHER LEVEL QUALITY IS REQUIRED. IN THE TAILORED VERSION OF THE ISO 9001:2008, ANY REFERENCES WHICH CITE THE ENTIRE INTERNATIONAL STANDARD ARE INTERPRETED AS EXCLUSIONS TO THIS DOCUMENT.
DLA TAILORED HIGHER LEVEL QUALITY CLAUSE FROM ISO 9001:2008

4.1 General requirements, [excluding reference to 1.2and excluding NOTE
4.2.1 General, [excluding subparagraph a)]
4.2.2 Quality manual, [excluding subparagraph a)]
4.2.3 Controlof documents
4.2.4 Control of records
5.1 Management commitment
5.3 Quality policy
6.2.2 Competence, training and awareness
6.4 Work environment
7.1 Planning of product realization, [excluding NOTE 2]
7.2.1 Determination of requirements related to theproduct
7.2.2 Review of requirements related to the product
7.2.3 Customer communication
7.4.1 Purchasing process
7.4.3 Verification of purchased product
7.5.1 Control of production and service provision
7.5.3 Identification and traceability
7.5.4 Customerproperty
7.5.5 Preservation of product
7.6 Control of monitoring and measuring equipment
8.1 General, [excluding subparagraph b) and subparagraph c)]
8.2.2 Internal audit
8.2.4 Monitoring and measurement of product
8.3 Control of nonconforming product
8.5.2Corrective action
8.5.3 Preventive action

GOVERNMENT/CONTRACTOR FAT, PACKAGING FAT and
GOVERNMENT/CONTRACTOR PLT IS REQUIREDIAW
SQAP002790093.

DESTRUCTIVE TESTING APPLIES.

The following Contract Data Requirements Lists (CDRLs), DD Form 1423s,
apply tothis procurement. Review the Technical Data Package (TDP) for
additional information.
Contractor First Article Test Report
Production Lot Acceptance Test Report
Certificate of Conformance
Quality Program Plan

CLASS I OZONE DEPLETING CHEMICALS ARE NOT TO BE
USED NORINCORPORATED IN ANY ITEMS TO BE
DELIVERED UNDER THIS CONTRACT.THIS PROHIBITION
SUPERSEDES ALL SPECIFICATION REQUIREMENTS BUT
DOESNOT ALLEVIATE ANY PRODUCT REQUIREMENTS.
SUBSTITUTE CHEMICALS MUST BE SUBMITTED FOR
APPROVAL UNLESS THEY ARE AUTHORIZED BYTHE
SPECIFICATION REQUIREMENTS.

The following Engineering Exceptions shall apply to this procurement:
Drawing 81361 5-19-916-2,Product Data Management System Technical Data
Package List, Valid from 2/25/15 to 2/25/16, page 2, Drawing number
MIL-DTL-14506, REV SYM 'H' should be changed to 'J'.

ANSI MH1 can be obtained on the Material Handler's of America's website,
www.mhi.org, referenced simply as MH1. Standard is available at no cost
but free registration on the site is required to obtain.

THIS SHELF LIFE ITEM ISNON-EXTENDABLE, CODE S,
WITH A TOTAL SHELF LIFE OF SIXTY MONTHS.
MATERIAL FURNISHED UNDER THIS CONTRACT/ORDER
SHALL HAVE AT LEAST85% (51 MONTHS) OF SHELF
LIFE REMAINING AT TIME OF DELIVERY.

SHELF LIFE MARKINGS REQUIRED PER 5.10.1 OF
MIL-STD-129: SHELF-LIFEMARKINGS SHALL BE SHOWN AS
PART OF THE ITEM IDENTIFICATION DATA ON UNIT PACKS,
INTERMEDIATE CONTAINERS, EXTERIOR CONTAINERS,AND
UNPACKED ITEMS. SHELF-LIFE MARKINGS SHALL INCLUDE
THE CURED DATE AND THE EXPIRATION DATE.

THE EXPIRATION DATE SHALL BECALCULATED FROM THE CURED
DATE OF THE RUBBER/ELASTOMER.

FULL AND OPEN COMPETITION APPLY
This is an identified Chemical Biological Defense Equipment item.

All requests for waivers or deviations, both pre and post award, must be
approved by theappropriate Joint Program Executive Office for Chemical
and Biological Defense (JPEO-CBD) ESA prior to final approval.

All packaged items of supply shall be marked IAW MIL-STD-129.

Requirements defining levels of pack shall be IAW MIL-STD-2073-1. If
militarypackaging is required and Special Packaging Instructions (SPI)
are provided in the technical data package (TDP), then the packaging
shall be IAW the provided SPI.

 CRITICAL APPLICATION ITEM

IAW BASIC DRAWING NR 81361 5-19-916
REVISION NR AD DTD01/22/2015
PART PIECE NUMBER: C5-19-916-2

IAW REFERENCE SPEC NR MIL-DTL-14506J
REVISION NR J DTD 10/03/2006
PART PIECENUMBER:

IAW REFERENCE STD NR MIL-STD-129R
REVISION NR R DTD 10/03/2006
PART PIECE NUMBER: TYPE I SHELF LIFE, 60 MONTHS

IAWREFERENCE NON GOVT STD ASTM D2000-12
REVISION NR 12 DTD 02/14/2012
PART PIECE NUMBER:

IAW REFERENCE NON GOVT STD SAEAMS-QQ-W-428A
REVISION NR DTD 10/07/2006
PART PIECE NUMBER:

IAW REFERENCE QAP 16236 SQAP002790093
REVISION NR F DTD05/11/2015
PART PIECE NUMBER:

IAW REFERENCE DRAWING NR 81361 5-19-916-2
REVISION NR DTD 02/25/2015
PART PIECE NUMBER:

IAWREFERENCE DRAWING NR 81361 5-19-916-2
REVISION NR A DTD 04/07/2014
PART PIECE NUMBER:

IAW REFERENCE QAP 16236CDRL-ECBCPLTC-15062
REVISION NR DTD 03/03/2015
PART PIECE NUMBER:

IAW REFERENCE QAP 16236 CDRL-ECBCCOC-15062
REVISION NRDTD 03/03/2015
PART PIECE NUMBER:

IAW REFERENCE QAP 16236 CDRL-ECBCFATC-15062
REVISION NR DTD 03/03/2015
PART PIECENUMBER:

IAW REFERENCE QAP 16236 CDRL-ECBCQPP-15062
REVISION NR DTD 03/03/2015
PART PIECE NUMBER:

PKGING DATA - MIL-STD-2073-1D, 15 DEC 1999
QUP:001 PRES MTHD:ZZ CLNG/DRY:Z PRESV MAT:ZZ
WRAP MAT:ZZ CUSH/DUNN MAT:ZZ CUSH/DUNNTHKNESS:Z
UNIT CONT:ZZ OPI:A
INTRMDTE CONT:ZZ INTRMDTE CONT QTY:ZZZ
PACK CODE:U
MARKING SHALL BE IN ACCORDANCE WITHMIL-STD-129.
SPECIAL MARKING CODE:32 -32 Type I, shelf life

PALLETIZATION SHALL BE IN ACCORDANCE WITH MD00100452 REV B DATED JULY01, 2008

DM_15_002790093 - DATE:-12 FEB 2015

NSN:4720-00-279-0093

PRESERVATION: MILITARY
LEVEL OF PACKING: -B--
QUANTITY PERUNIT PACKAGE: -001-
SPI NUMBER P5-19-916-2, Rev A, Date 7 APR 2014-

PLACE A RED X AND THE WORDS"SHORT BOX" ON THE FRONT OF ANY BOXTHAT HAS A SHORT QUANTITY, THEN PLACE THAT BOX/BOXES WITH THE MARKINGS SHOWING ON THE TOP FRONT OF THE PALLET LOAD.

Certificates of Conformances (see CDRL for COC format IAW
DI-MISC-81356A) are required for all material and shall be submitted as
part of the First Article Test report (FATR). COC's are also required
for packaging materials. The contractor is responsible for all
inspections and testing regardless of who conducts the actual testing.

A packaging FAT is required and shall consist of three (3) packaged
unitsinspected IAW SPI P5-19-916-2.

THIS SHELF LIFE ITEM IS NON-EXTENDABLE, CODE S,
WITH A TOTAL SHELF LIFE OF SIXTY MONTHS.
MATERIALFURNISHED UNDER THIS CONTRACT/ORDER
SHALL HAVE AT LEAST 85% (51 MONTHS) OF SHELF
LIFE REMAINING AT TIME OFDELIVERY.

SHELF LIFE MARKINGS REQUIRED PER 5.10.1 OF
MIL-STD-129: SHELF-LIFE MARKINGS SHALL BE SHOWN AS
PART OF THE ITEM IDENTIFICATION DATA ON UNIT PACKS,
INTERMEDIATE CONTAINERS, EXTERIOR CONTAINERS, AND
UNPACKED ITEMS. SHELF-LIFE MARKINGS SHALL INCLUDE
THE CURED DATE AND THE EXPIRATION DATE.

THE EXPIRATION DATE SHALL BE CALCULATED FROM THE CURED
DATE OF THERUBBER/ELASTOMER.

PARCEL POST ADDRESS:

W25G1U
W1BG DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2001 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US

FREIGHT SHIPPING ADDRESS:

W25G1U
W1BG DLA DISTRIBUTION
DDSP NEW CUMBERLAND FACILITY
2001 NORMANDY DRIVE DOOR 113 TO 134
NEW CUMBERLAND PA 17070-5002
US