B.08.03 Solicitation 20B00150001.pdf

AMENDMENT OF SOLICITATION/MODIFICATION OF CONTRACT

Except as provided herein, all terms and conditions of the document referenced in Item 9A or 10A, as heretofore changed, remains unchanged and in full force and effect.

15A. NAME AND TITLE OF SIGNER (Type or print)

30-105-04EXCEPTION TO SF 30

APPROVED BY OIRM 11-84

STANDARD FORM 30 (Rev. 10-83)

Prescribed by GSA

FAR (48 CFR) 53.243

POC: Chandra Crow ; 509-527-7202: chandra.d.crow @usace.army.mil

The purpose of this amendment is to remove the suggestion that the Government w ill accept a propellor propulsion method. The Government w ill only accept a jet propulsion method under this requirement. Additionally the due date for bids is extended to 01 June as 31 May is a

Sunday.

1. CONTRACT ID CODE PAGE OF PAGES

J 1 4

16A. NAME AND TITLE OF CONTRACTING OFFICER (Type or print)

16C. DATE SIGNED

BY 18-May-2020

16B. UNITED STATES OF AMERICA15C. DATE SIGNED15B. CONTRACTOR/OFFEROR

(Signature of Contracting Officer)(Signature of person authorized to sign)

8. NAME AND ADDRESS OF CONTRACTOR (No., Street, County, State and Zip Code) X W912EF20B0015

X 9B. DATED (SEE ITEM 11)

01-May-2020

10B. DATED (SEE ITEM 13)

9A. AMENDMENT OF SOLICITATION NO.

11. THIS ITEM ONLY APPLIES TO AMENDMENTS OF SOLICITATIONS

X The above numbered solicitation is amended as set forth in Item 14. The hour and date specified for receipt of Offer X is extended, is not extended.

Offer must acknowledge receipt of this amendment prior to the hour and date specified in the solicitation or as amended by one of the following methods:

(a) By completing Items 8 and 15, and returning 1 copies of the amendment; (b) By acknowledging receipt of this amendment on each copy of the offer submitted;

or (c) By separate letter or telegram which includes a reference to the solicitation and amendment numbers. FAILURE OF YOUR ACKNOWLEDGMENT TO BE

RECEIVED AT THE PLACE DESIGNATED FOR THE RECEIPT OF OFFERS PRIOR TO THE HOUR AND DATE SPECIFIED MAY RESULT IN

REJECTION OF YOUR OFFER. If by virtue of this amendment you desire to change an offer already submitted, such change may be made by telegram or letter, provided each telegram or letter makes reference to the solicitation and this amendment, and is received prior to the opening hour and date specified.

12. ACCOUNTING AND APPROPRIATION DATA (If required)

13. THIS ITEM APPLIES ONLY TO MODIFICATIONS OF CONTRACTS/ORDERS.

IT MODIFIES THE CONTRACT/ORDER NO. AS DESCRIBED IN ITEM 14.

A. THIS CHANGE ORDER IS ISSUED PURSUANT TO: (Specify authority) THE CHANGES SET FORTH IN ITEM 14 ARE MADE IN THE

CONTRACT ORDER NO. IN ITEM 10A.

B. THE ABOVE NUMBERED CONTRACT/ORDER IS MODIFIED TO REFLECT THE ADMINISTRATIVE CHANGES (such as changes in paying office, appropriation date, etc.) SET FORTH IN ITEM 14, PURSUANT TO THE AUTHORITY OF FAR 43.103(B).

C. THIS SUPPLEMENTAL AGREEMENT IS ENTERED INTO PURSUANT TO AUTHORITY OF:

D. OTHER (Specify type of modification and authority)

E. IMPORTANT: Contractor is not, is required to sign this document and return copies to the issuing office.

14. DESCRIPTION OF AMENDMENT/MODIFICATION (Organized by UCF section headings, including solicitation/contract subject matter where feasible.)

10A. MOD. OF CONTRACT/ORDER NO.

2. AMENDMENT/MODIFICATION NO. 5. PROJECT NO.(If applicable)

6. ISSUED BY

3. EFFECTIVE DATE

18-May-2020

CODE

USAED, WALLA WALLA - CONTRACTING DIV.

CHANDRA D. CROW

201 N. THIRD AVENUE

WALLA WALLA WA 99362-1876

W912EF 7. ADMINISTERED BY (If other than item 6)

4. REQUISITION/PURCHASE REQ. NO.

CODE

See Item 6

FACILITY CODECODE

EMAIL:TEL:

W912EF20B0015

SECTION SF 30 BLOCK 14 CONTINUATION PAGE

SUMMARY OF CHANGES

SECTION A - SOLICITATION/CONTRACT FORM

The required response date/time has changed from 31-May-2020 02:00 PM to 01-Jun-2020 02:00 PM.

SECTION C - DESCRIPTIONS AND SPECIFICATIONS

The following have been modified:

TECHNICAL SPECIFICATIONS

LUCKY PEAK DAM & LAKE

TAILERABLE WORKBOAT

1.0 Intent

1.1 These specifications cover the manufacture, outfitting, and delivery of one new aluminum, single gas powered engine, jet driven trailerable workboat ready for freshwater operation and with suitable trailer.

The contractor shall provide all labor, material, equipment, and engineering necessary to build and deliver a boat meeting the specifications below.

2.0 SCOPE

2.1 The vessel shall comply with all current U.S. Coast Guard Regulations, U.S. Army Corps of Engineers

Safety Manual EM 385-1-1 Section 19, and Federal and State environmental requirements with respect to a vessel’s function, construction and equipment outfitting.

2.2 The vessel shall be newly manufactured and shall be built entirely of aluminum by a proven manufacturer regularly engaged in the manufacture of trailerable welded aluminum boats. A custom built boat is not necessary and modifications to a stock model design is acceptable.

2.3 The vessel is to be used as a workboat in a fresh water environment and shall reflect that type of construction inside and out. The vessel's hull shall be properly reinforced for operations on inland waterways of the Boise River in the Pacific Northwest.

2.4 The general layout of the vessel shall incorporate a partially enclosed cabin area with glass windshield, sliding glass side windows on the port and starboard, hard top, doghouse engine cover, and a continuous level deck from the transom to the bow or to the greatest extent possible.

2.5 A trailer shall be provided that can transport the vessel to and from dry storage. The trailer shall be capable of safely towing the vessel at speeds greater than 55 MPH.

2.6 All welding shall be accomplished in accordance with the recommendations of the manufacturer and for the material used in the construction of the vessel. All sharp and /or rough edges shall be ground round and smooth and all weld splatter and slag shall be removed. All exterior seams and butts shall be flush and smooth and the hull plating shall be shrunk as required to remove all ripples and make fair.

3.0 WORKBOAT MINIMUM REQUIREMENTs

3.1 Hull:

3.1.1 Length: 24 feet (maximum)

3.1.2 Width: 9 feet (minimum)

3.1.3 Material: Appropriate ASTM standard for fresh water marine vessels

3.1.4 Shell Plating: 3/8” aluminum plate (minimum)

3.1.5 Bulwarks: Continuous all around hull.

3.1.6 Bitts: One 4 inch (maximum) OD center line aft towing bitt.

3.1.7 Anodes shall be installed on hull below the waterline.

3.1.8 Dog House: Engine shall be covered with a doghouse and be hinged for access.

3.1.9 Anchor box: An anchor box shall be installed in the bow of the vessel.

3.1.10 Swim deck: An extended swim deck shall be installed.

3.1.11 Ladders: One ladder shall be install on the bow and one ladder shall be installed on the swim deck.

3.1.12 Fuel Tank: 80 gallon (maximum) belly tank.

3.1.13 Coating: Deck area, gunnels, and doghouse shall be covered in a nonskid coating or material.

3.1.14 Light bar mount: Rooftop light bar mount

3.2 Cabin:

3.2.1 Seating: Both pilot and co-pilot seats shall be air ride single passenger seats. Two bench style seats shall be installed aft of the pilot and co-pilot seats. All seats shall be covered in standard marine grade upholstery.

3.2.2 Bow Door: Watertight door in the center of the windshield to access the bow of the vessel.

3.2.3 Windows: Stationary glass windshields shall be fitted with windshield wipers for pilot and co-pilot poisons. Horizontal sliding side windows on port and starboard and removable soft cover with zip and/or roll up capability to cover the aft section of the cabin. All glass windows made of tempered safety glass and have solar tint.

3.2.4 Washdown kit: A minimum of one washdown kit shall be installed.

3.2.5 Rearview Mirror: A rearview mirror shall be installed on the pilot’s side.

3.2.6 Heater: Marine grade heater shall be installed.

3.2.7 Cup holders: A minimum of 2 cup holders shall be installed. Cup holders shall be assessable to pilot and co-pilot.

3.3 Propulsion Machinery:

3.3.1 Single gas powered 4 stroke engine, 440 HP (minimum).

3.3.2 Reverse: 212 hydraulic reverse pump.

3.3.3 Steering: Starboard helm steering.

3.3.4 Propulsion: Jet drive.

3.4 Instrumentation & Electronics:

3.4.1 Analog gauge package: Engine tachometer, oil pressure, and volt meter. Audible and visual alarm for low oil, high temperature, and fuel level.

3.4.2 12-volt electric or air signal horn.

3.4.3 Standard four speaker stereo.

3.4.4 Two 12-volt ports

3.4.5 Ray Marine Axiom Pro 12.

3.4.6 Ray Marine Axiom pro 9 Display.

3.5 Lighting and Electrical:

3.5.1 Electric Batteries: Two 12-volt heavy-duty marine batteries mounted in Coast Guard approved battery boxes.

3.5.2 Bilge Pump: Minimum of two 12-volt bilge pumps.

3.5.3 An auto bilge switch shall be installed.

3.5.4 A minimum of 2 dome lights with the option for red light.

3.5.5 Rear deck lights.

3.5.6 Blackout switch for night vision.

3.6 Trailer

3.6.1 Galvanized tandem axle (approximately 5200 lbs).

3.6.2 Electric brakes.

3.6.3 Side roller guides.

3.6.4 Spare tire.

4.0 WARRANTY:

Builder to warrant workmanship and equipment installation for a minimum of one (1) year (longer if builder’s standard practice). Builder to provide all equipment and materials warranty/guarantee documents to purchaser at point of delivery.

5.0 OPERATION AND MAINTENANCE MANUALS

5.1 Two (2) complete copies of the Operation and Maintenance Manual shall be provided. The manuals shall include instructions on the maintenance, repair, troubleshooting, warranty, and a list of recommended spare parts. Any information pertaining to models or components not supplied under this contract shall be crossed out.

5.2 Also included shall be the name, phone and fax numbers, and email address of the contractor, manufacturer, and a distributor where spare parts can be purchased.

6.0 SHIPMENT & DELIVERY:

6.1 All items shall be delivered FOB destination to Lucky Peak Dam & Lake within six (6) months of contract award.

6.2 The contractor shall be responsible for packing and shipping the boat in a manner that will ensure undamaged and complete arrival to Lucky Peak Dam & Lake.

6.3 No shipments are allowed other than normal business hours of Monday through Thursday 7:00 a.m. -

4:00 p.m., excluding Federal holidays.

6.4 All shipments shall be delivered to:

Lucky Peak Dam & Lake, 9723 E Hwy 21, Boise, ID 83716

(End of Summary of Changes)