Updated_Specifications.pdf

REQUIREMENT:

The minimum specifications for the Hydraulic Excavator are listed below. BRAND

NAME OR EQUAL ITEMS WILL BE ACCEPTED. This requirement will also

Include the trade in of one PWA-415 JCB 175 Rubber tired excavator with ser# JCBJW17CK91505459. Please include in your response whether you will accept, and offer credit for the trade-ins.

SPECIFICATIONS:

Hydraulic Excavator Specifications:

Brand new Caterpillar 325F L CR Hydraulic Tracked Excavator or equal.

The following specifications at a minimum:

1. 160 HORSEPOWER TURBO DIESEL TEIR 4 ENGINE MINIMUM

2. OPERATING WEIGHT 57,000 POUNDS MINIMUM

3. MINIMUM 27,000 POUND LIFT CAPACITY WITHOUT BUCKET ATTACHED

4. COMPACT RADIUS DESIGN FOR MINIMUM TAIL AND FRONT SWING RADIUS

FOR TIGHT QUARTER WORK

5. ROPS PROTECTED OPERATORS CAB WITH A MINMUM 69 DECIBLES SOUND

PROTECTION

6. AUTOMATIC 2 SPEED TRAVEL MODES WITH A 3 MILES PER HOUR MAXIMUM

TRAVEL SPEED

7. MINIMUM 32 FOOT OVERALL REACH

8. MINIMUM 22 FOOT DIG DEPTH

9. 31 INCH MINIMUM TRACK WIDITH WITH STREET PADS

10. 85 GALLON FUEL TANK MINIMUM

11. ENGINE BLOCK HEATER 120 VOLT AC

12. HYDRAULIC OIL HEATER 120 VOLT AC

13. LOCKABLE BATTERY POWER DISCONNECT SWITCH

14. HYDRAULIC CONTROL SWITCH PATTERNS FROM ISO TO BACKHOE MODES

15. 24 VOLT ELECTRICAL SYSTEM

16. HEAVY DUTY HVAC SYSTEM TO INCLUDE AUTOMATIC CLIMATE CONTOL

17. DELUXE HIGH BACK AIR RIDE OPERATORS SEAT WITH HEAT AND HEAD REST

18. CRUISE CONTROL

19. TOOLBOX

20. CUP HOLDER

21. FRONT AND REAR WINDSHIELD WIPERS WITH WASHERS

22. 24 VOLT DC CONVERTOR TO 12 VOLT DC

23. AM/FM RADIO

24. REAR CAMERA SYSTEM

25. INTERIOUR AND EXTERIOUR REARVIEW MIRRORS

26. FRONT, REAR AND BOOM MOUNTED HALOGEN WORK LIGHTS

27. BEACON

28. FRONT SUN VISOR

29. UNDER CARRIAGE BOTTOM PLATES AND TRACK GUARDS

30. GROUND LEVEL GREASE POINTS

31. REACH BOOM AND STICK DESIGN

33. IN CAB HYDRAULIC ATTACHMENT CHANGING SYSTEM

34. STICK MOUNTED HYDRAULIC QUICK DISCONNECTS FOR

ATTACMENTS

35. HYDRAULIC THUMB

36. 36 INCH SEVERE DUTY DIRT DIGGING BUCKET WITH FIELD

REPLACABLE TEETH WITH QUICK COUPLER PINS

37. 48 INCH SEVERE DUTY DIRT DIGGING BUCKET WITH FIELD

REPLACEABLE TEETH WITH QUICK COUPLER PINS

38. 60 INCH HYDRAULIC TILTABLE DITCHING BUCKET WITH BOLT ON

CUTTING EDGE WITH QUICK COUPLER PINS

AND HYDRAULIC QUICK DISCONNECTS

39. 3 YEAR 3000 HOUR FULL COVERAGE EQUIPMENT WARRANTY

40. 3 COPIES OF ALL OPERATORS, SERVICE AND PARTS MANUALS

41. HYDRAULIC HAMMER 4500 IMPACT ENERGY CLASS WITH 300 TO

700 BLOWS PER MINUTE WITH MOLE POINT. ALSO MUST BE ABLE TO

LEAVE THUMB ON WHILE HAMMER IS IN USE WITH QUICK COUPLERS

WITH PINS

*A site visit to inspect the trade in excavator has been scheduled for May 15th, 2018 at 10:00 am eastern standard time in order to allow the Contractors to determine the trade in value of the excavator. Once a contract has been awarded a final inspection of the excavator will be scheduled to verify their condition. Please make contact via email to Ruth.torres4.civ@mail.mil if you are planning to attend the site visit and we will then send you the location. Please let us know no later than Monday 14th at 1pm.

**The contractor is responsible for coordinating the concurrent pick-up of the trade in Excavator with the delivery of the new Excavator.

***WHEN PROVIDING A PRICE FOR THE EXCAVTOR PLEASE PROVIDE

THE COST OF EXCAVATOR MINUS THE TRADE IN VALUE. PLEASE

INCLUDE THE VALUE FOR THE TRADE‐IN IN THE CLIN DESCRIPTION ON

FEDBID.

mailto:Ruth.torres4.civ@mail.mil