SPMYM1-18-Q-0063.docx

SPMYM118Q0063

Section SF 1449 - CONTINUATION SHEET

CONTACT INFORMATION

If your company encounters any problems with this purchase order/contract, including payment problems, please contact Romel Jackson by email at romel.jackson1@navy.mil or by telephone at 757-396-9354

NOTES

NOTE: Contractors (drivers) delivering material to the Norfolk Naval Shipyard must come with two forms of Identification, one being a driver license or picture ID card issued by a State. The other form required is a SSN card, birth certificate issued by a state, Native American document or US citizen card. Driver(s) will not be escorted unless they have to go into the CIA.

All items/boxes over 40 lbs under this solicitation and/or contract is required to be palletized. Delivery will not be accepted to any material that IS NOT palletized. The shipment will not be offloaded and will be returned.

Material sourced or otherwise procured from NUFLO, Inc. (Cage Code: 3BZG7) and/or Synergy Flow Systems (Cage Code: 4GP29) are prohibited to be offered, sold, exchanged, or delivered to Norfolk Naval Shipyard.

Contract Number MUST be noticeable on the outside of the package and on the packing documents.

OQE Ordering Requirement For CIM

Provide written verification that the chemical and mechanical properties have been determined and are acceptable for all document(s) in this package, as follows:

(a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Certify that a slow strain tensile (SSRT) test of “start material” has been accomplished per QQ-N-N286 requirements.

Note 1: Enter the specification

Note 2: Enter the document number

N421588060B304

FFP

CAP SCREW, 1-1/4"-7

CAP SCREW, HEX HEAD, 1-1/4"-7UNC-3AX5-1/2"LONG, K MONEL, QQ-N-286G,MIL-S-1222J

ORDERING DATA FOR DOCUMENT# 8060B304

MIL_DTL-1222J

A: General specification for Studs, Bolts, Screws and Nuts for applications where a high degree of reliability is required;

Mil-Dtl-1222J; 08 December 2000 B: M1222RN20C388NCNN; Hex Head Cap Screw, 1-1/4” -7- UNC-3A x 5-1/2” long , Type I, Alloy Type; Grade 500, annealed and age hardened.

C. Latest Revision D. N/A E: No Coating Required F thru J. N/A K. Locking element NOT required L. Cap screws to be marked IAW 3.13 (.K.)

M. All reports required. NOTE : Where headed fastener specifications require a yield strength test and a wedge tensile test, a separate (new, untested) fastener is required for each of the two methods, and both of these tests shall be reported.

N. N/A O. N/A P. N/A Q. Cap screws to be inspected IAW 4.3.2 and 4.3.2.1 R. Acceptance criteria IAW 4.3.2 and 4.3.2.1 S. Nondestructive testing and acceptance criteria shall be IAW 4.3.3 T. Mechanical Test are to be done after final heat treatment

U. IAW 5.1

V thru BB. N/A

QQ-N-286G

A. Nickel-Copper Aluminum Alloy, Wrought (UNS N05500); QQ-N-286G, 07 December 2000 B. Form 2, Annealed and age hardened C. Latest Revision D. Forging sketch not required E. Size required to suit mfg. of fastener F. Not required G. N/A H. Tolerances are to be as specified I. Not required J. Not required K. To suit mfg. of fastener L. N/A M. Edges as specified N. To suit mfg. of fasteners O. Markings as specified P. Mechanical test required (not for re-forging) Q. N/A R. Solution annealed and SSRT IAW 4.3.6.2 S. SSRT laboratory shall be one of attached listed facilities

SUPPLY NOTE: ADDITIONAL REQUIREMENTS (1423’S ATTACHED)

OQE Ordering Requirement For CIM

Provide written verification that the chemical and mechanical properties have been determined and are acceptable IAW the required specification MIL-DTL-1222J as applicable for document # 8060B304 are as follows:

Slow Strain Rate Tensile (SSRT) Testing Facilities

1. Huntington Alloys, a Special Metals Company Attn: Frank Veltry 3200 Riverside Drive Huntington, WV 25705 Phone: (304) 526-5759

FAX: (304) 526-5973

2. Metallurgical Consultants, Inc.

Attn: W. M. Buehler 4820 Caroline PO Box 88046 Houston, TX 77288-0046 Phone: (713) 526-6351

FAX: (713) 526-5576

3. Naval Surface Warfare Center (NSWC), Carderock Division Attn: Eric Focht Code 614 3500 Macarthur Blvd.

West Bethesda, MD 20817-5700 Phone: (301) 227-5032

FAX: (301) 227-5576

4. Teledyne Allvac Attn: Dr. W. D. Cao 2020 Ashcraft Ave.

Monroe, NC 28110 Phone: (704) 289-4511

FAX: (704) 289-4269

5. Mannesmann Röhrenwerke Mannesmann Forschungsinstitut (MFI) Attn: Dr. Weiss Postfach 251160 47251 Duisburg Germany Phone: 011-49-0203-999-3194

FAX: 011-49-0203-999-4415

FOB: Destination

MILSTRIP: N421588060B304

PURCHASE REQUEST NUMBER: N421588060B304

PROJECT: 5T9

NET AMT

N421588060B305

CAP SCREW, 1-1/4"-7

CAP SCREW, HEX HEAD, 1-1/4-7-3AX5-1/4"LONG, K MONEL, QQ-N-286G,MIL-S-1222J

ORDERING DATA FOR DOCUMENT# 8060B305

MIL_DTL-1222J

A: General specification for Studs, Bolts, Screws and Nuts for applications where a high degree of reliability is required;

Mil-Dtl-1222J; 08 December 2000 B: M1222RN20C384NCNN; Hex Head Cap Screw, 1-1/4” -7- UNC-3A x 5-1/4” long , Type I, Alloy Type; Grade 500, annealed and age hardened.

C. Latest Revision D. N/A E: No Coating Required F thru J. N/A K. Locking element NOT required L. Cap screws to be marked IAW 3.13 (.K.)

M. All reports required. NOTE : Where headed fastener specifications require a yield strength test and a wedge tensile test, a separate (new, untested) fastener is required for each of the two methods, and both of these tests shall be reported.

N. N/A O. N/A P. N/A Q. Cap screws to be inspected IAW 4.3.2 and 4.3.2.1 R. Acceptance criteria IAW 4.3.2 and 4.3.2.1 S. Nondestructive testing and acceptance criteria shall be IAW 4.3.3 T. Mechanical Test are to be done after final heat treatment

U. IAW 5.1

V thru BB. N/A

QQ-N-286G

A. Nickel-Copper Aluminum Alloy, Wrought (UNS N05500); QQ-N-286G, 07 December 2000 B. Form 2, Annealed and age hardened C. Latest Revision D. Forging sketch not required E. Size required to suit mfg. of fastener F. Not required G. N/A H. Tolerances are to be as specified I. Not required J. Not required K. To suit mfg. of fastener L. N/A M. Edges as specified N. To suit mfg. of fasteners O. Markings as specified P. Mechanical test required (not for re-forging) Q. N/A

Attn: Frank Veltry 3200 Riverside Drive Huntington, WV 25705 Phone: (304) 526-5759

FAX: (304) 526-5973

2. Metallurgical Consultants, Inc.

Attn: W. M. Buehler 4820 Caroline PO Box 88046 Houston, TX 77288-0046 Phone: (713) 526-6351

FAX: (713) 526-5576

3. Naval Surface Warfare Center (NSWC), Carderock Division Attn: Eric Focht Code 614 3500 Macarthur Blvd.

West Bethesda, MD 20817-5700 Phone: (301) 227-5032

FAX: (301) 227-5576

4. Teledyne Allvac Attn: Dr. W. D. Cao 2020 Ashcraft Ave.

Monroe, NC 28110 Phone: (704) 289-4511

FAX: (704) 289-4269

5. Mannesmann Röhrenwerke Mannesmann Forschungsinstitut (MFI) Attn: Dr. Weiss Postfach 251160 47251 Duisburg Germany Phone: 011-49-0203-999-3194

FAX: 011-49-0203-999-4415

OQE Ordering Requirement For CIM

Provide written verification that the chemical and mechanical properties have been determined and are acceptable for all document(s) in this package, as follows:

(a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Certify that a slow strain tensile (SSRT) test of “start material” has been accomplished per QQ-N-N286 requirements.

MILSTRIP: N421588060B305

NET AMT

N421588060B306

CAP SCREW, 1-1/4"-7

cap screw, hex head, 1-1/4-UNC-3A X 4-3/4" LONG, K MONEL, QQ-N-286G, MIL-S-1222J

ORDERING DATA FOR DOCUMENT# 8060B306

MIL_DTL-1222J

A: General specification for Studs, Bolts, Screws and Nuts for applications where a high degree of reliability is required;

Mil-Dtl-1222J; 08 December 2000 B: M1222RN20C376NCNN; Hex Head Cap Screw, 1-1/4” -7- UNC-3A x 4-3/4” long , Type I, Alloy Type; Grade 500, annealed and age hardened.

C. Latest Revision D. N/A E: No Coating Required F thru J. N/A K. Locking element NOT required L. Cap screws to be marked IAW 3.13 (.K.)

M. All reports required. NOTE : Where headed fastener specifications require a yield strength test and a wedge tensile test, a separate (new, untested) fastener is required for each of the two methods, and both of these tests shall be reported.

N. N/A O. N/A P. N/A Q. Cap screws to be inspected IAW 4.3.2 and 4.3.2.1 R. Acceptance criteria IAW 4.3.2 and 4.3.2.1 S. Nondestructive testing and acceptance criteria shall be IAW 4.3.3 T. Mechanical Test are to be done after final heat treatment

U. IAW 5.1

V thru BB. N/A

QQ-N-286G

A. Nickel-Copper Aluminum Alloy, Wrought (UNS N05500); QQ-N-286G, 07 December 2000 B. Form 2, Annealed and age hardened C. Latest Revision D. Forging sketch not required E. Size required to suit mfg. of fastener F. Not required G. N/A H. Tolerances are to be as specified I. Not required J. Not required K. To suit mfg. of fastener L. N/A M. Edges as specified N. To suit mfg. of fasteners O. Markings as specified P. Mechanical test required (not for re-forging) Q. N/A

OQE Ordering Requirement For CIM

Provide written verification that the chemical and mechanical properties have been determined and are acceptable for all document(s) in this package, as follows:

(a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Certify that a slow strain tensile (SSRT) test of “start material” has been accomplished per QQ-N-N286 requirements.

Note 1: Enter the specification

Note 2: Enter the document number

FOB: Destination

MILSTRIP: N421588060B306

NET AMT

N421588060B307

CAP SCREW, 1-1/8"-7

CAP SCREW, HEX HEAD, 1-1/8-UNC-2AX41/4 LONG, K MONEL, QQ-N-286G,MIL-S1222J

ORDERING DATA FOR DOCUMENT# 8060B307

MIL_DTL-1222J

A: General specification for Studs, Bolts, Screws and Nuts for applications where a high degree of reliability is required;

Mil-Dtl-1222J; 08 December 2000 B: M1222RN18C268NCNN; Hex Head Cap Screw, 1-1/8” -7- UNC-2A x 4-1/4” long , Type I, Alloy Type; Grade 500, annealed and age hardened.

C. Latest Revision D. N/A E: No Coating Required F thru J. N/A K. Locking element NOT required L. Cap screws to be marked IAW 3.13 (.K.)

M. All reports required. NOTE : Where headed fastener specifications require a yield strength test and a wedge tensile test, a separate (new, untested) fastener is required for each of the two methods, and both of these tests shall be reported.

N. N/A O. N/A P. N/A Q. Cap screws to be inspected IAW 4.3.2 and 4.3.2.1 R. Acceptance criteria IAW 4.3.2 and 4.3.2.1 S. Nondestructive testing and acceptance criteria shall be IAW 4.3.3 T. Mechanical Test are to be done after final heat treatment

U. IAW 5.1

V thru BB. N/A

QQ-N-286G

A. Nickel-Copper Aluminum Alloy, Wrought (UNS N05500); QQ-N-286G, 07 December 2000 B. Form 2, Annealed and age hardened C. Latest Revision D. Forging sketch not required E. Size required to suit mfg. of fastener F. Not required G. N/A H. Tolerances are to be as specified I. Not required J. Not required K. To suit mfg. of fastener L. N/A M. Edges as specified N. To suit mfg. of fasteners O. Markings as specified P. Mechanical test required (not for re-forging) Q. N/A

Attn: Frank Veltry 3200 Riverside Drive Huntington, WV 25705 Phone: (304) 526-5759

FAX: (304) 526-5973

2. Metallurgical Consultants, Inc.

Attn: W. M. Buehler 4820 Caroline PO Box 88046 Houston, TX 77288-0046 Phone: (713) 526-6351

FAX: (713) 526-5576

3. Naval Surface Warfare Center (NSWC), Carderock Division Attn: Eric Focht Code 614 3500 Macarthur Blvd.

West Bethesda, MD 20817-5700 Phone: (301) 227-5032

FAX: (301) 227-5576

4. Teledyne Allvac Attn: Dr. W. D. Cao 2020 Ashcraft Ave.

Monroe, NC 28110 Phone: (704) 289-4511

FAX: (704) 289-4269

5. Mannesmann Röhrenwerke Mannesmann Forschungsinstitut (MFI) Attn: Dr. Weiss Postfach 251160 47251 Duisburg Germany

Provide written verification that the chemical and mechanical properties have been determined and are acceptable for all document(s) in this package, as follows:

(a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Certify that a slow strain tensile (SSRT) test of “start material” has been accomplished per QQ-N-N286 requirements.

MILSTRIP: N421588060B307

NET AMT

N421588060B308

CAP SCREW, 1-1/8"-7

CAP SCREW, HEX HEAD, 1-1/8"-7UNC-2AX4" LONG, K MONEL, QQ-N-286G, MIL-S-1222J

ORDERING DATA FOR DOCUMENT# 8060B308

MIL_DTL-1222J

A: General specification for Studs, Bolts, Screws and Nuts for applications where a high degree of reliability is required;

Mil-Dtl-1222J; 08 December 2000 B: M1222RN18C264NCNN; Hex Head Cap Screw, 1-1/8” -7- UNC-2A x 4” long, Type I, Alloy Type; Grade 500, annealed and age hardened.

C. Latest Revision D. N/A E: No Coating Required F thru J. N/A K. Locking element NOT required L. Cap screws to be marked IAW 3.13 (.K.)

M. All reports required. NOTE : Where headed fastener specifications require a yield strength test and a wedge tensile test, a separate (new, untested) fastener is required for each of the two methods, and both of these tests shall be reported.

N. N/A O. N/A P. N/A Q. Cap screws to be inspected IAW 4.3.2 and 4.3.2.1 R. Acceptance criteria IAW 4.3.2 and 4.3.2.1 S. Nondestructive testing and acceptance criteria shall be IAW 4.3.3 T. Mechanical Test are to be done after final heat treatment

U. IAW 5.1

V thru BB. N/A

QQ-N-286G

A. Nickel-Copper Aluminum Alloy, Wrought (UNS N05500); QQ-N-286G, 07 December 2000 B. Form 2, Annealed and age hardened C. Latest Revision D. Forging sketch not required E. Size required to suit mfg. of fastener F. Not required G. N/A H. Tolerances are to be as specified I. Not required J. Not required K. To suit mfg. of fastener L. N/A M. Edges as specified N. To suit mfg. of fasteners O. Markings as specified P. Mechanical test required (not for re-forging) Q. N/A

Attn: Frank Veltry 3200 Riverside Drive Huntington, WV 25705 Phone: (304) 526-5759

FAX: (304) 526-5973

2. Metallurgical Consultants, Inc.

Attn: W. M. Buehler 4820 Caroline PO Box 88046 Houston, TX 77288-0046 Phone: (713) 526-6351

FAX: (713) 526-5576

3. Naval Surface Warfare Center (NSWC), Carderock Division Attn: Eric Focht Code 614 3500 Macarthur Blvd.

West Bethesda, MD 20817-5700 Phone: (301) 227-5032

FAX: (301) 227-5576

4. Teledyne Allvac Attn: Dr. W. D. Cao 2020 Ashcraft Ave.

Monroe, NC 28110 Phone: (704) 289-4511

FAX: (704) 289-4269

5. Mannesmann Röhrenwerke Mannesmann Forschungsinstitut (MFI) Attn: Dr. Weiss Postfach 251160 47251 Duisburg Germany

Provide written verification that the chemical and mechanical properties have been determined and are acceptable for all document(s) in this package, as follows:

(a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Certify that a slow strain tensile (SSRT) test of “start material” has been accomplished per QQ-N-N286 requirements.

Note 1: Enter the specification

Note 2: Enter the document number

FOB: Destination

MILSTRIP: N421588060B308

NET AMT

N421588060B309

CAP SCREW, 1-1/8'-7

CAP SCREW, HEXHEAD, 1-1/8-7-UNC2X3-3/4" LONG, K MONEL, QQ-N286G,MIL-S-1222J

ORDERING DATA FOR DOCUMENT# 8060B309

MIL_DTL-1222J

A: General specification for Studs, Bolts, Screws and Nuts for applications where a high degree of reliability is required;

Mil-Dtl-1222J; 08 December 2000 B: M1222RN18C260NCNN; Hex Head Cap Screw, 1-1/8” -7- UNC-2A x 3-3/4” long, Type I, Alloy Type; Grade 500, annealed and age hardened.

C. Latest Revision D. N/A E: No Coating Required F thru J. N/A K. Locking element NOT required L. Cap screws to be marked IAW 3.13 (.K.)

M. All reports required. NOTE: Where headed fastener specifications require a yield strength test and a wedge tensile test, a separate (new, untested) fastener is required for each of the two methods, and both of these tests shall be reported.

N. N/A O. N/A P. N/A Q. Cap screws to be inspected IAW 4.3.2 and 4.3.2.1 R. Acceptance criteria IAW 4.3.2 and 4.3.2.1 S. Nondestructive testing and acceptance criteria shall be IAW 4.3.3 T. Mechanical Test are to be done after final heat treatment

U. IAW 5.1

V thru BB. N/A

QQ-N-286G

A. Nickel-Copper Aluminum Alloy, Wrought (UNS N05500); QQ-N-286G, 07 December 2000 B. Form 2, Annealed and age hardened C. Latest Revision D. Forging sketch not required E. Size required to suit mfg. of fastener F. Not required G. N/A H. Tolerances are to be as specified I. Not required J. Not required K. To suit mfg. of fastener L. N/A M. Edges as specified N. To suit mfg. of fasteners O. Markings as specified P. Mechanical test required (not for re-forging) Q. N/A

Attn: Frank Veltry 3200 Riverside Drive Huntington, WV 25705 Phone: (304) 526-5759

FAX: (304) 526-5973

2. Metallurgical Consultants, Inc.

Attn: W. M. Buehler 4820 Caroline PO Box 88046 Houston, TX 77288-0046 Phone: (713) 526-6351

FAX: (713) 526-5576

3. Naval Surface Warfare Center (NSWC), Carderock Division Attn: Eric Focht Code 614 3500 Macarthur Blvd.

West Bethesda, MD 20817-5700 Phone: (301) 227-5032

FAX: (301) 227-5576

4. Teledyne Allvac Attn: Dr. W. D. Cao 2020 Ashcraft Ave.

Monroe, NC 28110 Phone: (704) 289-4511

FAX: (704) 289-4269

5. Mannesmann Röhrenwerke Mannesmann Forschungsinstitut (MFI) Attn: Dr. Weiss Postfach 251160 47251 Duisburg Germany Phone: 011-49-0203-999-3194

FAX: 011-49-0203-999-4415

OQE Ordering Requirement For CIM

Provide written verification that the chemical and mechanical properties have been determined and are acceptable for all document(s) in this package, as follows:

(a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Certify that a slow strain tensile (SSRT) test of “start material” has been accomplished per QQ-N-N286 requirements.

Note 1: Enter the specification

Note 2: Enter the document number

FOB: Destination

MILSTRIP: N421588060B309

NET AMT

N421588060B310

CAP SCREW, 1-1/8"-7

CAP SCREW, HEX HEAD, 1"8-UNC-2AX4-7/8" LONG, K MONEL, QQ-N-286G, MIL-S-1222J

ORDERING DATA FOR DOCUMENT# 8060B310

MIL_DTL-1222J

A: General specification for Studs, Bolts, Screws and Nuts for applications where a high degree of reliability is required;

Mil-Dtl-1222J; 08 December 2000 B: M1222RN16C378NCNN; Hex Head Cap Screw, 1”-8- UNC-2A x 4-7/8” long, Type I, Alloy Type; Grade 500, annealed and age hardened.

C. Latest Revision D. N/A E: No Coating Required F thru J. N/A K. Locking element NOT required L. Cap screws to be marked IAW 3.13 (.K.)

M. All reports required. NOTE: Where headed fastener specifications require a yield strength test and a wedge tensile test, a separate (new, untested) fastener is required for each of the two methods, and both of these tests shall be reported.

N. N/A O. N/A P. N/A Q. Cap screws to be inspected IAW 4.3.2 and 4.3.2.1 R. Acceptance criteria IAW 4.3.2 and 4.3.2.1 S. Nondestructive testing and acceptance criteria shall be IAW 4.3.3 T. Mechanical Test are to be done after final heat treatment

U. IAW 5.1

V thru BB. N/A

QQ-N-286G

A. Nickel-Copper Aluminum Alloy, Wrought (UNS N05500); QQ-N-286G, 07 December 2000 B. Form 2, Annealed and age hardened C. Latest Revision D. Forging sketch not required E. Size required to suit mfg. of fastener F. Not required G. N/A H. Tolerances are to be as specified I. Not required J. Not required K. To suit mfg. of fastener L. N/A M. Edges as specified N. To suit mfg. of fasteners O. Markings as specified P. Mechanical test required (not for re-forging) Q. N/A

Attn: Frank Veltry 3200 Riverside Drive Huntington, WV 25705 Phone: (304) 526-5759

FAX: (304) 526-5973

2. Metallurgical Consultants, Inc.

Attn: W. M. Buehler 4820 Caroline PO Box 88046 Houston, TX 77288-0046 Phone: (713) 526-6351

FAX: (713) 526-5576

3. Naval Surface Warfare Center (NSWC), Carderock Division Attn: Eric Focht Code 614 3500 Macarthur Blvd.

West Bethesda, MD 20817-5700 Phone: (301) 227-5032

FAX: (301) 227-5576

4. Teledyne Allvac Attn: Dr. W. D. Cao 2020 Ashcraft Ave.

Monroe, NC 28110 Phone: (704) 289-4511

FAX: (704) 289-4269

5. Mannesmann Röhrenwerke Mannesmann Forschungsinstitut (MFI) Attn: Dr. Weiss Postfach 251160 47251 Duisburg Germany Phone: 011-49-0203-999-3194

FAX: 011-49-0203-999-4415

OQE Ordering Requirement For CIM

Provide written verification that the chemical and mechanical properties have been determined and are acceptable for all document(s) in this package, as follows:

(a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Certify that a slow strain tensile (SSRT) test of “start material” has been accomplished per QQ-N-N286 requirements.

MILSTRIP: N421588060B310

NET AMT

N421588060B311

CAP SCREW, 1/2-13"

CAP SCREW, HEX HEAD, 1/3"-UNC-3AX2-1/2" LONG, JK MONEL, QQ-N-286G, MIL-S-1222

OQE Ordering Requirement For CIM

Provide written verification that the chemical and mechanical properties have been determined and are acceptable for all document(s) in this package, as follows:

(a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Certify that a slow strain tensile (SSRT) test of “start material” has been accomplished per QQ-N-N286 requirements.

Provide written verification that the chemical and mechanical properties have been determined and are acceptable for all document(s) in this package, as follows:

(a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Certify that a slow strain tensile (SSRT) test of “start material” has been accomplished per QQ-N-N286 requirements.

Note 1: Enter the specification

Note 2: Enter the document number

FOB: Destination

MILSTRIP: N421588060B311

NET AMT

N421588060B312

CAP,SCREW 1-1/4"-7

CAP,SCREW 1-1/4"-7-UNC-2AX4-1/2" LONG, MONEL, QQ-N-281D,MIL-S-1222J

ORDERING DATA FOR DOCUMENT # 8060B312

MIL_DTL-1222J

A: General specification for Studs, Bolts, Screws and Nuts for applications where a high degree of reliability is required;

Mil-Dtl-1222J; 08 December 2000 B: M1222RN20C272NANN; Hex Head Cap Screw, 1-1/4” -7- UNC-2A x 4-1/2” long, Type I, QQ-N-281, Alloy Type; Nickel , Alloy Grade ; 400 As Formed or Stress Relieved, uncoated.

C. Latest Revision D. N/A E: No Coating Required F thru J. N/A K. Locking element NOT required L. Cap screws to be marked IAW 3.13 (.K.)

M. All reports required

* NOTE: “WHERE HEADED FASTENER SPECIFICATIONS REQUIRE A YIELD STRENGTH TEST AND A WEDGE TENSILE TEST, A SEPARATE (NEW, UNTESTED) FASTENER IS REQUIRED FOR EACH OF THE TWO METHODS, AND BOTH OF THESE TESTS SHALL BE REPORTED.”

N. N/A O. N/A P. N/A Q. Cap screws to be inspected IAW 4.3.2 and 4.3.2.1 R. Acceptance criteria IAW 4.3.2 and 4.3.2.1 S. Nondestructive testing and acceptance criteria shall be IAW 4.3.3 T. Mechanical Test are to be done after final heat treatment

U. IAW 5.1

V thru BB. N/A

REMARKS: 1. Chemical Analysis and Mechanical test reports required, see para (M)

2. Mercury Free Clause Applies.

OQE Ordering Requirement For CIM

Provide written verification that the chemical and mechanical properties have been determined and are acceptable for all document(s) in this package, as follows:

(a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Certify that a slow strain tensile (SSRT) test of “start material” has been accomplished per QQ-N-N286 requirements.

MILSTRIP: N421588060B312

NET AMT

N421588060B313

CAP SCREW, 1-1/8"-7

CAP SCREW, HEX HEAD, 1-1/8"-7UNC-2AX5-1/2" LONG,MONEL, QQ-N-281D,MIL-S-1222J

ORDERING DATA FOR DOCUMENT # 8060B313

A: General specification for Studs, Bolts, Screws and Nuts for applications where a high degree of reliability is required;

Mil-Dtl-1222J; 08 December 2000 B: M1222RN18C288NANN; Hex Head Cap Screw, 1-1/8” -7- UNC-2A x 5-1/2” long, Type I, QQ-N-281, Alloy Type; Nickel , Alloy Grade ; 400 As Formed or Stress Relieved, uncoated.

C. Latest Revision D. N/A E: No Coating Required F thru J. N/A K. Locking element NOT required L. Cap screws to be marked IAW 3.13 (.K.)

M. All reports required

* NOTE: “WHERE HEADED FASTENER SPECIFICATIONS REQUIRE A YIELD STRENGTH TEST AND A WEDGE TENSILE TEST, A SEPARATE (NEW, UNTESTED) FASTENER IS REQUIRED FOR EACH OF THE TWO METHODS, AND BOTH OF THESE TESTS SHALL BE REPORTED.”

N. N/A O. N/A P. N/A Q. Cap screws to be inspected IAW 4.3.2 and 4.3.2.1 R. Acceptance criteria IAW 4.3.2 and 4.3.2.1 S. Nondestructive testing and acceptance criteria shall be IAW 4.3.3 T. Mechanical Test are to be done after final heat treatment

U. IAW 5.1

V thru BB. N/A

REMARKS: 1. Chemical Analysis and Mechanical test reports required, see para (M)

2. Mercury Free Clause Applies.

Provide written verification that the chemical and mechanical properties have been determined and are acceptable for all document(s) in this package, as follows:

(a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Certify that a slow strain tensile (SSRT) test of “start material” has been accomplished per QQ-N-N286 requirements.

MILSTRIP: N421588060B313

MFR PART NR: 9B

NET AMT

N421588060B315

CAP SCREW, 1-1/8"-7

CAP SCREW, HEX HEAD, 1-1/8"-7UNC-2AX3-3/4" LONG, MONEL, QQ-N281D, MIL-S-1222J

ORDERING DATA FOR DOCUMENT # 8060B315

A: General specification for Studs, Bolts, Screws and Nuts for applications where a high degree of reliability is required;

Mil-Dtl-1222J; 08 December 2000 B: M1222RN18C260NANN; Hex Head Cap Screw, 1-1/8” -7- UNC-2A x 3-3/4” long, Type I, QQ-N-281, Alloy Type; Nickel , Alloy Grade ; 400 As Formed or Stress Relieved, uncoated.

C. Latest Revision D. N/A E: No Coating Required F thru J. N/A K. Locking element NOT required L. Cap screws to be marked IAW 3.13 (.K.)

M. All reports required

* NOTE: “WHERE HEADED FASTENER SPECIFICATIONS REQUIRE A YIELD STRENGTH TEST AND A WEDGE TENSILE TEST, A SEPARATE (NEW, UNTESTED) FASTENER IS REQUIRED FOR EACH OF THE TWO METHODS, AND BOTH OF THESE TESTS SHALL BE REPORTED.”

N. N/A O. N/A P. N/A Q. Cap screws to be inspected IAW 4.3.2 and 4.3.2.1 R. Acceptance criteria IAW 4.3.2 and 4.3.2.1 S. Nondestructive testing and acceptance criteria shall be IAW 4.3.3 T. Mechanical Test are to be done after final heat treatment

U. IAW 5.1

V thru BB. N/A

REMARKS: 1. Chemical Analysis and Mechanical test reports required, see para (M)

2. Mercury Free Clause Applies.

OQE Ordering Requirement For CIM

Provide written verification that the chemical and mechanical properties have been determined and are acceptable for all document(s) in this package, as follows:

(a) Provide written verification that the chemical analysis and mechanical properties tests have been determined and are acceptable. All test reports will contain a signed certification that the results represent the actual values for the material provided and that they are in full compliance with the contract specification. Material certification data shall be recorded on the testing company's letterhead and shall bear the name, title and signature of the authorized company representative. The name and title shall be clearly legible. Certification data supplied to the government shall be either the original mill material certification, the original copy from the testing facility, or exact photocopies of these documents. The data forwarded by the manufacturer shall contain a signed certification that the reported results represent the actual attributes of the material furnished and indicate full compliance with all applicable specification and contract requirements. Statements on material certification documents must be positive and unqualified. The material certification data reports shall include quantitative data representing the actual values obtained during testing.

(b) Test reports will list all verified attributes and will be traceable to the material via a heat, lot, or batch number applied to the material by the manufacturer. Each piece of material must be marked with the applicable heat, lot, or batch number shown on the test reports provided.

(c) Test reports labeled "Typical," those with words such as "to the best of our knowledge" or "we believe the information contained herein is true" or those that have results transcribed from other reports or documents are not acceptable.

(d) Certify that a slow strain tensile (SSRT) test of “start material” has been accomplished per QQ-N-N286 requirements.

Note 1: Enter the specification

Note 2: Enter the document number

FOB: Destination

MILSTRIP: N421588060B315

NET AMT