Specs.pdf

Bureau of Reclamation, 1820 South Rio Grande, Montrose CO. 81401

Specifications for Skid Steer Loader Scope

The Bureau of Reclamation, Curecanti Field Division (CCI) has a need for (1) compact track loader (Skid Steer) delivered to Curecanti Field Division, 1330 East Oak Grove, Montrose, Colorado, 81401-4858.

General Requirements

John Deere Compact Track Loader 333G or equivalent to be considered the compact track loader must have the following requirements;

Skid steer shall have a turbo charged diesel engine SAE rated between 90 and 100 gross horsepower.

The diesel engine shall be equipped with cold starting aid such as intake heater.

The diesel engine shall be equipped with 120v block heater.

Skid steer shall have a rated operating capacity at 35% of tipping load capacity (SAE) of 3500 pounds or greater.

Skid steer shall have a rated tipping load (SAE) of 9500 pounds or greater.

Skid steer shall have a lifting height of 125 inches or greater, measured from ground to bucket hinge pin.

Skid steer shall have rollover protection system (ROPS) that meets SAE-J1040 and ISO 3471.

Skid steer shall have a falling object protection (FOPS) that meets SAE-J1040 and ISO 3471.

Skid Steer shall have an enclosed operator cab equipped with entrance/exit door; integrated operator controlled heating and air conditioning, fully adjustable suspension seat with seat belt, windshield wiper, and instrument panel, front and rear floodlights, strobe light, rear view mirror, AM/FM radio and backup camera.

Skid steer shall have automatic bucket leveling device capable of keeping bucket level as bucket travels through its entire stroke.

Skid steer shall have high flow auxiliary hydraulics capable of 40 gpm or greater.

Skid steer shall be capable of operating high flow snow blower, hydraulic trencher, hydraulic hammer, hydraulic flail mower, and hydraulic sweeper.

Skid steer shall have hydraulic quick attachment mounting system that allows the operator to mount and dismount attachments from the skid steer cab.

Skid steer shall be equipped with selectable controls to manipulate between ISO pilot and H-Pattern.

Skid steer shall be equipped with two speed travel.

Skid steer shall be equipped with tracks, heavy-duty rubber tire machines will not be accepted.

Skid steer shall have a minimum of 25-gallon fuel capacity.

Skid Steer shall have a hand operated throttle and a floor mounted accelerator pedal.

Contractor shall provide operation manuals, repair manual and parts manual.

Optional Accessories The optional equipment listed below will be priced separately the BOR reserves the right to decide what options will be purchased at time of award. All equipment shall all be compatible with quoted compact tracked loader and capable of being operated by remote control from the operator’s seat.

1 EA 80” Wide heavy-duty bucket with bolt on replaceable cutting edge.

1 EA Heavy duty, 4000 lbs, pallet forks with 48 “ long forks.

1 EA 96” Snow bucket with bolt on cutting edge.

1 EA Additional counterweights for compact tracked loader if available, installed.

1 EA Heavy duty hydraulic hammer.

Service and Parts Requirements

The Vendor shall provide a point of contact/dealer for the compact track loader, that can respond in 72 hours from the time the issue is reported and if they capability for onsite for repairs if needed. If the Vendor cannot provide contact or dealer that can respond in 72 hours, they shall provide the closest contact/dealer and the response time from the notice of issue including if they have the capability of onsite repair. The vendor shall a provide information on part availability and delivery, for commonly replaced and available spare parts.

Standards and Code Requirements Compact track loader and optional equipment will meet the following standards and codes;

Society of Automotive Engineers (SAE) SAE J1040 identifies the performance criteria for destructive testing of vehicles used by construction, earthmoving, forestry and mining industries.

International Organization for Standardization (ISO) ISO 3449 Earth Moving Machinery – Rollover protective structures, laboratory tests and performance requirements.

Delivery

Delivery shall be freight on board destination (FOBD) and shall be included in the total cost. The Contractor shall state the best schedule they can provide for delivery of the proposed equipment after receipt of award.

Delivery of compact track loader will be between the hours of 7:00 AM to 4:00 PM Monday through Friday.

The Contractor shall give notice of at least 48 hours prior to delivery Curecanti Field Division.

Point of contact for delivery will be:

Kay Schritter, lschritter@usbr.gov, (970) 240-6301 or Eric Langley, elangley@usbr.gov, 970-318-0945.

Delivery address is as follows: Bureau of Reclamation, Curecanti Field Division, 1330 East Oak Grove, Montrose, CO, 81404-4858.

Submittals for Quotations Vendor quotations shall include the following to be deemed acceptable:

1. Description of the compact track loader being quoted in sufficient detail to evaluate compliance with the stated specifications. Including any brochures and/or cut sheets to confirm the items meet the needs of the requirement.

2. The Vendor shall provide a point of contact/dealer for the compact track loader, that can respond in 72 hours from the time the issue is reported and if they capability for onsite for repairs if needed. If the Vendor cannot provide contact or dealer that can respond in 72 hours, they shall provide the closest contact/dealer and the response time from the notice of issue including if they have the capability of onsite repair. The vendor shall a provide information on part availability and delivery, for commonly replaced and available spare parts.

3. Standard Manufacturer warranty with stated terms.

4. Lead time for (FOBD) delivery after receipt of award.

5. The contractor must list any exceptions when submitting quote.

If vendor fails to submit the above information the quote can be found to be non-responsive.

mailto:elangley@usbr.gov