RFQATTACH.SPE4AK18Q0027.0005.DOC

1560004689164

PANEL,ACCESS

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS)

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS)

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

1 PG = 2 EA

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

MIL-STD-130N(1) DATED 16 NOV 2012.

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

BAE SYSTEMS (OPERATIONS) LTD U9143 F292681

1560996443997

BRACKET, STRUCTURAL COMPONENT, AIRCRAFT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

BAE SYSTEMS (OPERATIONS) LTD U9143 75A325359-1001

1560997992356

BRACKET, STRUCTURAL COMPONENT, AIRCRAFT

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS)

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS)

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

MIL-STD-130N(1) DATED 16 NOV 2012.

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

BAE SYSTEMS (OPERATIONS) LTD U9143 75A326532-1005

1560998148660

BRACKET, STRUCTURAL COMPONENT, ACFT

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ001: HIGHER LEVEL CONTRACT QUALITY REQUIREMENTS (MANUFACTURERS AND NON-MANUFACTURERS)

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

RQ017: PHYSICAL INDENTIFICATION/BARE ITEM MARKING

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

BAE SYSTEMS (OPERATIONS) LTD U9143 75A326532-1003

5306012412643

BOLT, SHEAR

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

Certificate of Quality Compliance (CoQC) Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information. If CDRL-COQCCDRLs is missing from DLA Collaboration Folders (CFolders) they can also be viewed in Appendix 1 of the DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx

The following Contract Data Requirements Lists (CDRLs), DD Form 1423s, apply to this procurement. Review the Technical Data Package (TDP) for additional information.

*** THIS ITEM IS DEFINED BY EITHER BY A MILITARY PART STANDARD, OR A PART STANDARD PUBLISHED BY A CONSENSUS NON-GOVERNMENT STANDARDS ORGANIZATION.***

HARDWARE MANUFACTURED TO THE CURRENT REVISION OF THE PART STANDARD DEFINING THIS ITEM IS ACCEPTABLE.

HARDWARE MANUFACTURED IN THE PAST TO A PREVIOUS, BUT THEN CURRENT, REVISION OF THE STANDARD IS ACCEPTABLE.

ANY HARDWARE MANUFACTURED FROM THE DATE OF THIS SOLICITATION FORWARD, SHALL BE MANUFACTURED IN ACCORDANCE WITH THE CURRENT REVISION OF THE PART STANDARD IN QUESTION.

MIL-STD-130N, 16 Nov 2012

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

ITEM SURFACE MARKING REQUIREMENT: IN ADDITION TO MARKING REQUIREMENTS DEFINED BY TECHNICAL DATA, THE MANUFACTURER'S SYMBOL IS REQUIRED AND SHALL BE APPLIED DIRECTLY TO THE SURFACE OF THIS ITEM. THE MANUFACTURER'S SYMBOL MUST BE LISTED IN MIL-HDBK-57. DO NOT PLACE ANY MARKINGS ON BEARING SURFACES. MANUFACTURER'S SYMBOL IS NOT REQUIRED ON FASTENERS WITH A THREAD DIAMETER OF 0.190 INCHES AND SMALLER.

FOR MANUFACTURER'S SYMBOL REGISTRATION INFORMATION AND INQUIRIES PLEASE VISIT THE MIL-HDBK-57 URL AT:

http://www.dla.mil/TroopSupport/IndustrialHardware/Engineering-and-Technical-services/logoreg/

CRITICAL ITEM - SOURCE INSPECTION REQUIRED.

*** GAUGING REQUIREMENTS AS FOLLOWS ***

ALL CLASS 3A AND 3B THREADS WILL BE INSPECTED

FOR DIMENSIONAL CONFORMANCE IN ACCORDANCE WITH

SYSTEM 22 OF FED-STD-H28/20. THIS EXCLUDES

SELF-LOCKING NUTS, INTERNAL THREADS SMALLER

THAN .190 INCH DIA AND EXTERNAL THREADS SMALLER

THAN .138 INCH DIA.

THE DRAWING(S) LISTED BELOW ARE AVAILABLE AT

DLA DURING *OPEN SOLICITATION ONLY*.

TO RECEIVE A COPY OF THE DRAWING(S),

FOR EBS SOLICITATIONS USE URL

HTTPS://WWW.DIBBS.BSM.DLA.MIL/RFQ/

AWARDS OF THIS NSN MUST BE SOURCE INSPECTED

UNLESS AWARDED TO A QSLM/QSLD SUPPLIER THAT

IS LISTED ON THE APPLICABLE QSL LIST AND

SUPPLYING MATERIAL THAT IS IN COMPLIANCE

WITH THE QSL PROGRAM.

QUALIFIED SUPPLIERS LIST FOR MANUFACTURERS/QUALIFIED SUPPLIERS LIST FOR DISTRIBUTORS (QSLM/QSLD) REQUIREMENT (DLA TROOP SUPPORT MARCH 1995) FOR FSC'S 5305, 5306, 5307 AND 5310 (NUTS).

ONLY MANUFACTURERS/DISTRIBUTORS LISTED ON THE QSLM/QSLD ARE ELIGIBLE FOR AN AWARD PURSUANT TO THIS SOLICITATION (CLASS 3 FASTENERS). SUPPLIERS NOT QUOTING IN COMPLIANCE WITH THE QSLM/QSLD REQUIREMENT MUST INDICATE THEY ARE DEVIATING FROM THE REQUIREMENTS OF THE SOLICITATION.

ANY BID/QUOTE/OFFER BASED ON A PRODUCT SUPPLIED BY OTHER THAN AN APPROVED QSL DISTRIBUTOR, EVEN THOUGH THE PRODUCT MIGHT HAVE BEEN MANUFACTURED IN ACCORDANCE WITH THE DRAWING(S) AND/OR SPECIFICATION(S) AS CITED IN THE PURCHASE ORDER TEXT (POT) IS A BID/QUOTE/OFFER WITH EXCEPTION AND MUST BE SO INDICATED BY THE/ QUOTER/OFFEROR.

ANY PRODUCT FURNISHED UNDER A CONTRACT OR ORDER FOR A PRODUCT DESIGNATED AS PART OF THE QSL PROGRAM, UNLESS SPECIFICALLY AUTHORIZED BY THE OVERNMENT IN WRITING, MUST FULLY COMPLY WITH THE TERMS AND CONDITIONS OF THE QSL PROGRAM. ANY PRODUCT, WHICH DOES NOT FULLY COMPLY WILL BE CONSIDERED AN UNAUTHORIZED SUBSTITUTION, AND MAY YIELD CRIMINAL PENALTIES IN ADDITION TO ANY / CIVIL REMEDIES AVAILABLE TO THE GOVERNMENT.

FOR THIS SOLICITATION, AND ANY RESULTING ORDER ISSUED TO AN APPROVED QSLM/QSLD SUPPLIER WHOSE QUOTE IS BASED ON COMPLIANCE WITH THE QSL PROGRAM, (EXCEPT IN THE CASE OF FMS (FOREIGN MILITARY SALE) REQUIREMENTS), REFERENCES TO SOURCE INSPECTION ARE HEREBY WAIVED. IN SUCH CASES, COQC, PVT, QAP-EQ003,ASQ H133,and RQ006, IF REFERNCED, DO NOT APPLY.

FOR MORE INFORMATION ABOUT THE QSL PROGRAM GO TO THE FOLLOWING WEBSITE:

http://www.dla.mil/TroopSupport/IndustrialHardware/Engineering-and-Technical-services/Qualified-Suppliers-List/

-OR- WRITE TO:

DLA TROOP SUPPORT, ATTN: DLA TROOP SUPPORT - FHTF, BLDG 3/B, 700 ROBBINS AVENUE, PHILADELPHIA, PA 19111-5092

Qualification requirements in procurement note #M03 Qualified Suppliers List for Manufacturers (QSLM)/Qualified Suppliers List for Distributors (QSLD) for Troop Support# apply. The full text of procurement note M03 can be found in the DLA Directive (DLAD) of Procurement Notes on the Web at: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx.

(END STO)

*** THIS ITEM IS DESIGNATED AS A SPECIAL HIGH STRENGTH FASTENER AND IS REQUIRED TO SUPPORT THE DoD AVIATION COMMUNITY***

ARTICLES TO BE FURNISHED HEREUNDER SHALL BE MANUFACTURED, TESTED AND INSPECTED IN ACCORDANCE WITH REQUISITE TECHNICAL DATA, AND ALL DETAILS AND SPECIFICATIONS REFERENCED THEREIN.

SUPPLEMENTAL REQUIREMENTS

A. ADDITIONALLY, STRESS DURABILITY TESTING COMPLETED FOR THE EVALUATION OF THIS FASTENER, SHALL BE PERFORMED IN ACCORDANCE WITH THE ELONGATION METHOD, EXTERNAL LOADING METHOD, OR STRAIN GAGE METHOD OF NASM1312-5. THE TORQUE METHOD OF LOADING IS NOT ACCEPTABLE. SAMPLES SHALL BE LOADED FROM 75% TO 80% OF THE ACTUAL ULTIMATE TENSILE STRENGTH OF THE FASTENER DETERMINED BY TESTING, AND MAINTAINED FOR 72 HOURS. SAMPLES SHALL BE EXAMINED FOR CRACKING AND/OR FRACTURE IN ACCORDANCE WITH NASM1312-5.

B. ALL BOLTS, 100% OF THE MANUFACTURING LOT, SHALL BE EXAMINED BY MAGNETIC PARTICLE INSPECTION IN ACCORDANCE WITH THE PROCUREMENT SPECIFICATION. ANY BOLTS HAVING DISCONTINUITIES EQUAL TO OR EXCEEDING THE LIMITATIONS SPECIFIED IN THE PROCUREMENT SPECIFICATION SHALL BE REJECTED. CARE MUST BE EXERCISED TO AVOID CONFUSING CRACKS, AS DESCRIBED WITHIN THE PROCUREMENT SPECIFICATION, WITH OTHER DISCONTINUITIES.

5310004689163

WASHER, RECESSED

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

SAMPLING:

THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION, STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.

MIL-STD-130N, 16 Nov 2012

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

ADEQUATE DATA FOR EVALUATION OF ALTERNATE

OFFERS IS NOT AVAILABLE AT THE PROCUREMENT

AGENCY. THE OFFEROR MUST PROVIDE A COMPLETE

DATA PACKAGE INCLUDING DATA FOR THE APPROVED AND

ALTERNATE PART FOR EVALUATION.

BAE SYSTEMS PLC K1987 F292680

5310011815045

NUT,SELF-LOCKING,EXTENDED WASHER,HEXAGON

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

DATA IS PROPRIETARY OR INSUFFICIENT FOR

COMPETITIVE PROCUREMENT

THE ACCEPTABLE SOURCE(S) MUST MEET THE REQUIREMENTS

OF THE CURRENT REVISION OF THE OEM DRAWING

OFFERORS NOT CITED AS ACCEPTABLE SOURCES IN THE

PROCUREMENT ITEM DESCRIPTION ARE REQUIRED TO

OBTAIN SOURCE APPROVAL FROM THE DESIGN CONTROL

ACTIVITY. SOURCE APPROVAL REQUESTS/TECHNICAL

DATA PACKAGES MUST BE SUBMITTED TO DLA WITH

THE OFFER.

MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL

NOT BE INTENTIONALLY ADDED TO, OR COME IN DIRECT

CONTACT WITH, ANY HARDWARE OR SUPPLIES FURNISHED

UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY

USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED

INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;

AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.

PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS

CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN

A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR

MERCURY COMPOUND. (IAW NAVSEA 5100-003D).

NO ASBESTOS AS DEFINED IN FED-STD-313 IS

PERMITTED IN THIS ITEM

MIL-STD-130N(1) DATED 16 NOV 2012.

IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY

ITEM SURFACE MARKING REQUIREMENT: IN ADDITION TO MARKING REQUIREMENTS DEFINED BY TECHNICAL DATA, THE MANUFACTURER'S SYMBOL IS REQUIRED AND SHALL BE APPLIED DIRECTLY TO THE SURFACE OF THIS ITEM. THE MANUFACTURER'S SYMBOL MUST BE LISTED IN MIL-HDBK-57. DO NOT PLACE ANY MARKINGS ON BEARING SURFACES. MANUFACTURER'S SYMBOL IS NOT REQUIRED ON FASTENERS WITH A THREAD DIAMETER OF 0.190 INCHES AND SMALLER.

FOR MANUFACTURER'S SYMBOL REGISTRATION INFORMATION AND INQUIRIES PLEASE VISIT THE MIL-HDBK-57 URL AT:

http://www.dla.mil/TroopSupport/IndustrialHardware/Engineering-and-Technical-services/logoreg/

SPS TECHNOLOGIES, INC. 56878 79317CM-1032

BRISTOL INDUSTRIES 27238 BH787-3

5315994772570

PIN,HOLLOWED HEAD

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

BAE SYSTEMS PLC (K1987)

LONDON UNITED KINGDOM

P/N 75A325362-2001

5315995878762

PIN,HOLLOWED HEAD

RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT

RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS (IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB AT: http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx. FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.

RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES

BAE SYSTEMS PLC (K1987)

LONDON UNITED KINGDOM

P/N 75A325362-2001