Section_C_ _D_2-23-15_PGC_03259.docx

(Trousers, ECW, UR GRAY PGC 03259)

NSN(S) THIS PROCUREMENT

X-SMALL-SHORT 8415-01-545-9907 LARGE-LONG 8415-01-538-6706

X-SMALL-REG 8415-01-545-9914 X-LARGE-REG 8415-01-538-6707

SMALL-SHORT 8415-01-545-9955 X-LARGE-LONG 8415-01-538-6709

SMALL-REG 8415-01-538-6720 X-LARGE-X-LONG 8415-01-545-0040

SMALL-LONG 8415-01-545-9958 2X-LARGE-REG 8415-01-545-0117

MEDIUM-REG 8415-01-538-6695 2X-LARGE-LONG 8415-01-545-0118

MEDIUM-LONG 8415-01-545-0019 2X-LARGE-X-LONG 8415-01-545-0119

LARGE-REG 8415-01-538-6704

SECTION C- DESCRIPTION/SPECIFICATION

ITEM DESCRIPTION

TROUSERS, ECW (LOFT), URBAN GREY; layer 7 of ECWCS GEN 3 SHALL BE made in accordance with GL/PD-06-18 dated 28 DECEMBER 2007 and Interim changes below:

PATTERN DATE: JUNE 19, 2007

BASIC MATERIALS:

SHELL: 100% NYLON, PLAIN WEAVE, 3.3 OZ/SQ. YD., 115 X 100; WATER RESIST

LINING: 100% NYLON RIPSTOP, 1.7 OZ/SQ. YD.

BATTING (BODY): 6.0 OZ/SQ. YD. POLYESTER

STANDARD SAMPLE FOR CLOTH, PLAIN WEAVE, OUTERSHELL MATERIAL IAW PARA 3.4.1.1 IS AVAILABLE FOR SHADE UNDER ROLL #3782, URBAN GRAY 505.

GENERAL INSPECTION & ACCEPTABLE QUALITY LEVEL

VISUAL: Level II, AQL 2.5 DIMENSIONAL: Level S-3, AQL 2.5

QUALITY CONFORMANCE INSPECTION: IN ACCORDANCE WITH PARA. 4.3

END ITEM VISUAL EXAMINATION: IN ACCORDANCE WITH PARA. 4.1.1.1

FINISHED DIMENSIONS: IN ACCORDANCE WITH PARA. 4.4.2

END ITEM VISUAL EXAMINATION:

THE END ITEMS SHALL BE EXAMINED FOR DEFECTS LISTED IN TABLE VIII. THE LOT SZ SHALL BE EXPRESSED IN UNITS OF TROUSERS. THE SAMPLE UNIT SHALL BE ONE PAIR TROUSERS. THE INSPECTION LEVEL SHALL BE II, IN ACCORDANCE WITH ANSI/ASQQ Z1.4 AND THE AQL, EXPRESSED IN DEFECTS PER HUNDRED UNITS SHALL BE 1.5 FOR MAJOR DEFECTS AND 10 FOR (MAJOR AND MINOR COMBINED)DEFECTS.

END ITEM DIMENSIONAL EXAMINATION:

THE END ITEMS SHALL BE EXAMINED FOR CONFORMANCE TO DIMENSIONS SPECIFIED N TABLE IX. ANY DIMENSION NOT WITHIN THE SPECIFIED TOLERANCE SHALL BE CLASSIFIED AS A DEFECT. THE LOT SIZE SHALL BE EXPRESSED IN UNITS OF ONE TROUSERS.

THE SAMPLE UNIT SHALL BE ONE PAIR OF TROUSERS. THE INSPECTION LEVEL SHALL BE S-3 AND THE AQL, EXPRESSED IN TERMS OF DEFECTS PER HUNDRED UNITS, SHALL BE 2.5.

Packaging examination: Inspection level shall be S-2; AQL shall be 1.0.

Palletization examination: Inspection level shall be S-1; AQL shall be 4.0.

"PACKAGING AND PALLETIZATION EXAMINATION:

Packaging examination. The fully packaged end items shall be examined for the defects listed below. The lot size shall be expressed in units of shipping containers. The sample unit shall be one shipping container fully packaged. The inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 1.0.

Examine Defect Marking (exterior omitted, incorrect, illegible, of and interior) improper size, location, sequence, or method of application.

Materials Any component missing, damaged, or not as specified.

Workmanship Inadequate application of components such as:

incomplete closure of container flaps, loose strapping, improper taping, inadequate stapling, bulged or distorted container.

Content Number of items per shipping container is more or less than required. Size shown on one or more items not as specified on shipping container. 1/ 1/ For this defect, one item from each shipping container in sample shall be examined.

Palletization examination. An examination shall be made to determine that palletization complies with the section 5 requirements. Defects shall be scored in accordance with the list below. The sample unit shall be one palletized unit load fully packaged. The lot size shall be the number of palletized unit loads in the end item, inspected lot. The inspection level shall be S-1, and the acceptable quality level (AQL), expressed in terms of defects per hundred units, shall be 4.0 in accordance with ANSI/ASQ Z1.4.

Examine Defect Finished dimensions Length, width, or height exceeds specified maximum requirements.

Palletization Pallet pattern not as specified.

Interlocking of loads not as specified. 1 Load not bonded with required straps as specified.

Weight Exceeds maximum load limits.

Marking Omitted, incorrect, illegible, of improper size, location, sequence, or method of application.

INTERIM CHANGES TO GL/PD 06-18:

Page 1, Para. 1.2 delete all sizes listed and substitute the following:

XSmall-XShort XSmall-Short XSmall-Reg XSmall-Long XSmall-XLong XSmall-XXLong

Small-XShort Small-Short Small-Reg Small-Long Small-XLong Small-XXLong

Medium-XShort Medium-Short Medium-Reg Medium-Long Medium-XLong Medium-XXLong

Large-XShort Large-Short Large-Reg Large-Long Large-XLong Large-XXLong

XLarge-XShort XLarge-Short XLarge-Reg XLarge-Long XLarge-XLong XLarge-XXLong

XXLarge-XShort XXLarge-Short XXLarge-Reg XXLarge-Long XXLarge-XLong XXLarge-XXLong

PAGE 5, PARA .3.3.1, LINE 1, AFTER "ON THE BACK", ADD "(SEE 3.7.4)."

Page 10, Para. 3.5.5.2, line 6, after "shortened to ¾ to 1 inch finished length" delete "." And add ",except that the bottom slider thongs shall be shortened to ¾ to 1 inch finished length and be secured with a ½ inch bartack."

PAGE 8, PARA. 3.4.2, TABLE IV, UNDER "CHARACTERISTIC", LINE 3, DELETE "WARMTH @0.002...0.74" AND SUBSTITUTE "ITRINSIC CLO @ 0.002 PSI, (MIN.) - REQUIREMENT 3.5"

PAGE 10, PARA. 3.5.5, LINE 2, AFTER "BELOW." ADD "NOTE: 2" ZIPPER THONGS MAY BE USED TO ACCOMMODATE MANUFACTURING OPERATIONS."

PAGE 13, PARA. 3.7.2, TABLE VII, UNDER "SEAM TYPE" THE FOLLOWING CHANGES ARE APPLICABLE:

BACKSEAM AND INSEAM - DELETE "SSa-2" AND SUBSTITUTE "LSBM-3";

SIDE SEAMS - DELETE "LSq-3" AND SUBSTITUTE "LSq-2";

BOTTOM HEMMING - DELETE "EFb-1" AND SUBSTITUTE "SSAE-2";

HOOK/LOOP - DELETE "OSf-1" AND SUBSTITUTE "LSBj-1"

Page 14, Para. 3.7.3, table of bartacks, delete in its entirety and substitute:

"Bartack Location Bartack Length, Inch QTY per Garment Zipper Pull 3/4 4 Zipper Pull, Bottom 1/2 2"

Page 14, add new paragaraph "3.7.4" as follows:

"3.7.4. Loops, waistband. On the inside of the waistband, attach loops of 2-1/2 inch long nylon tape (3.5.2) by folding the tape ends under ¼ inch and backstitching across tape width, through all layers of the waistband, 1/16 inch from folded tape end. The opposite end of the tape loop shall be stitched in the same manner, approximately 1-1/4 inch from the first with the waistband under full extension. The length of the finished loop shall be approximately 1-5/8 inches. On the waistband, the center point of loop stitches shall finish on the front and back, both Right and Left sides, proportionally by garment size, as follows: For Size Medium: Front - 5-7/8 to 6-1/8 inches from center of front slide fastener; Back 5-3/4 to 5-5/8 inches from center of side slide fastener."

PAGE 16, TABLE VIII, UNDER "EXAMINATION" DELETE ALL DEFECTS FOR "HEAT SEALED SEAMS AND NON-WICKING BUFFER - MAJOR 117 THROUGH 125; AND MINOR 220 THROUGH 224"; DELETE ALL DEFECTS FOR "REPAIRS - MAJOR 126 AND 127; AND 225 AND 226"; DELETE ALL DEFECTS FOR "SEAM TAPE ADHESION - DEFECTS 128 AND 129; AND 227 AND 228"

PAGE 18, TABLE IX, ADD "NOTE":

"NOTE: UNDER TROUSERS FINISHED MEASUREMENTS TABLE, ALL MEASUREMENT LOCATIONS LISTED UNDER THE "REGULAR" COLUMN ARE REQUIRED FOR ALL LENGTHS. TO DETERMINE THE REQUIRED MEASUREMENT FOR THE VARIOUS LENGTHS - USE THE SIZING DESIGNATION ACROSS THE TOP OF THE TABLE (XS, S, M, etc.)."

Page 18, Para. 4.4.2, Table IX, under "5/, after "#is measured from", delete the remainder of the sentence and substitute " zipper stop to zipper stop".

PAGE 20, PARA. 4.5, TABLE X, UNDER "CHARACTERISTIC", "BATTING MATERIAL (INSULATION)", DELETE "(INSULATION)" AND SUBSTITUTE "(HEAVY WEIGHT)"; LINE 3, DELETE "WARMTH @ 0.002PSI" AND SUBSTITUTE "INTRINSIC CLO @0.002PSI".

CHANGES TO V-T-295E:

THREAD, NYLON; V-T-295 DATED AUGUST 1, 1985 IS HEREBY CANCELLED; FUTURE ACQUISITONS SHOULD REFER TO THREAD, NYLON, A-A-59826 DATED 03 MARCH 2009 AS A REPLACEMENT.

ADDITIONAL INFO FOR FED-STD-4 GLOSSARY OF FABRIC IMPERFECTIONS:

REVISION B: 7/29/64; AMENDMENT 2: 9/12/75

NOTICE 1, DATED 10/1/87.

DEV. TO FED. STD. 4B & AM. 2, PAGE 2, SEC.I. PARA. 2.1. IN IMPERFECTION

COMMERCIAL TERMINOLOGY AND GLOSSARY NO. COLUMNS, AFTER SHADE

BAR - 14 INSERT: "SHADED CLOTH-61B".

PAGE 8 PARA. 3.4, GLOSSARY NO. "61A- OFF SHADE", IN "DEFINITION" COLUMN,

DELETE ":SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END". ADD NEW

GLOSSARY NO. "SHADED CLOTH "61B-SHADED CLOTH (SHADED SIDE TO SIDE, SIDE

TO CENTER OR END TO END) WITH THE FOLLOWING DEFINITION: "COLOR

DIFFERENCE BETWEEN THE RESPECTIVE CLOTH AREAS".

PAGE 22, SECTION III, PARAGRAPH 2.1, IN "IMPERFECTION COMMERCIAL

TERMINOLOGY" AND GLOSSARY NO." COLUMNS, AFTER "SHADE BAR-15" INSERT:

"SHADED CLOTH - 62A"

PAGE 27, PARAGRAPH 3.4, GLOSSARY NO. "62-OFF SHADE" IN "DEFINITION"

COLUMN DELETE: "SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END".

ADD NEW GLOSSARY NO, "62A-SHADED CLOTH (SHADED SIDE TO SIDE, SIDE TO

CENTER OR END TO END)" WITH THE FOLLOWING DEFINITION: "COLOR DIFFERENCE

BETWEEN THE RESPECTIVE CLOTH AREAS."

DEVIATION FROM FED. STD. 4B, AND AMEND 2:

PG 2, SECTION 1, PARA.2.1, IN "IMPERFECTION COMMERCIAL TERMINOLOGY" AND

"GLOSSARY NUMBER" COLUMNS, AFTER "SHADE BAR-14",INSERT: "SHADED CLOTH

61B".

PG 8, PARA.3.4, GLOSSARY NUMBER "61A-OFF SHADE" IN "DEFINITION" COLUMN,

DELETE, "SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END". ADD NEW

GLOSSARY NO."61B SHADED CLOTH "SHADED SIDE TO SIDE, SIDE TO CENTER OR

END TO END" WITH THE FOLLOWING DEFINITION; "COLOR DIFFERENCE BETWEEN THE

RESPECTIVE CLOTH AREAS."

PAGE 22, SECTION III, PARAGRAPH 2.1, IN "IMPERFECTION COMMERCIAL

TERMINOLOGY" AN GLOSSARY NO." COLUMNS, AFTER "SHADE BAR-15"

INSERT: "SHADED CLOTH - 62A"

PAGE 27, PARAGRAPH 3.4, GLOSSARY NO "62-OFF SHADE" IN "DEFINITION"

COLUMN DELETE: "SHADED SIDE TO SIDE, SIDE TO CENTER OR END TO END".

ADD NEW GLOSSARY NO, "62A-SHADED CLOTH (SHADED SIDE TO SIDE, SIDE TO

CENTER OR END TO END)" WITH THE FOLLOWING DEFINITION: "COLOR DIFFERENCE

BETWEEN THE RESPECTIVE CLOTH AREAS."

Ref. T0202 - 04/04/07)

INTERIM CHANGES TO A-A-55126B,

THE FOLLOWING CHANGES ARE FOR ALL CURRENT, PENDING AND FUTURE PROCUREMENTS OF THE SUBJECT DOCUMENT UNTIL SUCH TIME AS THE DOCUMENT IS AMENDED OR REVISED.

PAGE 4. TABLE I, PHYSICAL REQUIREMENTS, CHARACTERISTIC, SHEAR STRENGTH,DELETE LBS/SQ INCH (MIN), ADD SHEAR STRENGTH, LBS/2 SQ INCH (MIN).

PAGE 5 TABLE II, PHYSICAL REQUIREMENTS; CHARACTERISTIC, LENGTH

DIMENSIONAL STABILITY, % (MAX); LOOP, ALL CLASSES DELETE .0; ADD ALL CLASSES 4.0.

PAGE 7, Paragraph 3.10.2, Change the following title of paragraph from: "Fray resistance of Universal Camouflage Shades" and replace with "Fray resistance of Camouflage Prints"

PAGE 14, Paragraph 7.3.4 Change the following title of paragraph from: Fray resistance for Universal Camouflage Shades." and replace with "Fray resistance for Camouflage Prints."

ADDITIONAL INFORMATION FOR A-A-55634A, 23 MARCH 2004:

SPECIAL NOTE!! ALL SLIDE FASTENERS USED ARE TO BE MEASURED FROM "STOP TO STOP". RECOMMEND THAT THIS MEASUREMENT BE TAKEN RANDOMLY BEFORE SLIDE FASTENERS ARE SEWN TO THE ITEMS, COVERALL, OR ANY ITEM REFERRED TO IN THE SOLICITATION. "THE QAR WILL REJECT ANY SLIDE THAT IS NOT LAYING FLAT AFTER IT IS SEWN INTO/ONTO AN ITEM." SPECIAL INFO ON ITEMS THAT UTILIZE SLIDE FASTENERS IS GIVEN BY "ALL USING MILITARY PERSONNEL".

MIL-STD-129 CURRENT REVISION UNLESS OTHERWISE SPECIFIED

- DEPARTMENT OF DEFENSE STANDARD PRACTICE

- MILITARY MARKING FOR SHIPMENT AND STORAGE

INTERIM CHANGES:

OMISSION OF MARKINGS ON EXTERIOR SHIPPING CONTAINERS OF ITEMS

IN THE DLA TROOP SUPPORT CLOTHING AND TEXTILE (C&T) DIRECTORATE:

THE NOMENCLATURE AND MANUFACTURER'S NAME (WHEN THE NAME IDENTIFIES THE MATERIAL) SHALL BE OMITTED FROM ALL EXTERIOR SHIPPING CONTAINERS OF DLA TROOP SUPPORT C&T ITEMS, REGARDLESS OF MODE OF SHIPMENT.

IF THE MANUFACTURER'S NAME DOES NOT IDENTIFY THE MATERIAL AS BEING CLOTHING, IT MAY REMAIN. NSNS SHALL BE SHOWN ON ALL SHIPPING CONTAINERS OF C&T ITEMS, THE PACKING LIST SHALL BE PLACED INSIDE THE LAST CONTAINER TO BE LOADED FOR EACH SHIPMENT. THE WORDS "PACKING LIST HERE" SHALL BE STENCILED, NOT HAND LETTERED, ON THE CONTAINER.

ADDITIONAL INFORMATION FOR MIL-PRF-5038:

ALL STANDARD SAMPLE INFORMATION WILL STILL APPLY.

STANDARD SAMPLES ARE AS FOLLOWS:

TAN 380, TYPE III, ROLL #3497, FOR SHADE, APPEARANCE AND COLORFASTNESS.

TAN 380, TYPE II, ROLL #3498, FOR SHADE, APPEARANCE AND COLORFASTNESS.

BLACK 375, TYPE III, ROLL #3443, FOR SHADE, APPEARANCE AND COLORFASTNESS.

OLIVE DRAB 7, TYPE IV, ROLL #3012, FOR SHADE, FINISH AND COLORFASTNESS.

CAMOUFLAGE GREEN 483, TYPE II, ROLL #3484, FOR SHADE, APPEARANCE AND COLORFASTNESS.

CAMOUFLAGE GREEN 483, TYPE III, ROLL #3485 FOR SHADE, APPEARANCE AND COLORFASTNESS.

CAMOUFLAGE GREEN 483, TYPE IV, ROLL #3486, FOR SHADE, APPEARANCE AND COLORFASTNESS.

STANDARD SAMPLE FOR FOLIAGE GREEN 504 IS MIL-C-44436, ROLL #3729 (THE FOLIAGE GREEN 502 AREA OF THE PATTERN).

STANDARD SAMPLE FOR DESERT SAND 503 IS MIL-C-44436, ROLL #3729 (THE DESERT SAND 500 AREA OF THE PATTERN).

FOLIAGE GREEN 504/DESERT SAND 503 IS TO BE USED AS SPECIFIED BY CONTRACT. THIS APPLIES TO TYPE III.

ADDITIONAL INFORMATION FOR V-T-285: V-T-285F IS HEREBY CANCELLED AND REPLACED BY MIL-DTL-32072, THREAD, POLYESTER, DATED JANUARY 8, 2002

(ref. T0706 - May 10, 2006)

MIL-DTL-32075: LABEL FOR CLOTHING, EQUIPAGE,

AND TENTAGE, GENERAL USE REPLACES DDD-L-20

(Ref. T0451 - June 19, 2007)

INTERIM SPECIFICATION CHANGES TO MIL-DTL-32075:

PAGE 4, PARA. 3.3.5, AFTER "TYPE III OR IV, CLASS 4 OF" DELETE "DDD-L-20" AND REPLACE "MIL-DTL-32075,".

PAGE 6, TABLE I, "PHYSICAL REQUIREMENTS OF THE

TYPE VI FINISHED LABEL." UNDER "TEARING

STRENGTH" DELETE: "(LB.) MINIMUM" AND

SUBSTITUTE: "(GNS) MINIMUM."

PAGE 12, PARA 3.3.2.17, AFTER "NSN" ADD

"AND THE UNIVERSAL PRODUCT CODE (UPC)

SUPPLIED BY THE GOVERNMENT, FOR ALL NSNs."

INCLUDE T6855 OBJECT TEXT ID ST

ADDITIONAL INFORMATION FOR MIL-T-3530:

INTERIM CHANGES TO MIL-T-3530H:

PAGE 2, LINE 2, DELETE "COPPER 8-QUINOLINOLATE" AND INSERT "MILDEW, AND LEACHING RESISTANT".

PAGE 2, PARA. 1.2, TYPE II, LINE 2, AFTER "POLYESTER," ADD "TEXTURED POLYESTER,".

PAGE 4, PARAGRAPH 3.5.1.1, DELETE IN ITS ENTIRETY, AND SUBSTITUTE "3.5.1.1 MILDEW AND LEACHING RESISTANCE. A CERTIFICATE OF COMPLIANCE WILL BE ACCEPTED WHICH CERTIFIES THAT THE TEXTILE MATERIAL SHALL RETAIN A 75% BREAKING STRENGTH AFTER 12 WEEKS EXPOSURE INITIALLY AND AFTER LEACHING WHEN EVALUATED AS SPECIFIED IN PARAGRAPH 4.4.5. AS AN ALTERNATE TEST, A 7 DAY EXPOSURE MAY BE USED WITH THE APPROVAL OF THE PROCURING AGENCY.

PAGE 4, PARAGRAPH 3.5.1.1.1, DELETE IN ITS ENTIRETY.

PAGE 7, PARAGRAPH 4.4.1.1, LINE 5, DELETE "COPPER 8-QUINOLINOLATE...3.5.1.1 AND 3.5.1.1.1" AND SUBSTITUTE "MILDEW, AND LEACHING RESISTANT. ..3.5.1.1, AND 4.4.5.1"

PAGE 9, TABLE II, UNDER CHARACTERISTICS COLUMN, LINE 1, DELETE "COPPER 8-QUINOLINOLATE ANALYSIS, (TYPE I, CLASS 1)" AND SUBSTITUTE "MILDEW RESISTANCE (TYPE I, CLASS 1): INITIAL AFTER LEACHING"

PAGE 9, TABLE II, UNDER REQUIREMENT PARAGRAPH COLUMN, LINE 2, DELETE "3.5.1.1.1" AND LINE 3, INSERT "4.4.5.1".

PAGE 9 TABLE II UNDER TEST METHOD COLUMN, LINE 2, DELETE "2060 AND 5762 1/", AND SUBSTITUTE "AATCC 30, TEST 1 1/, AND AS THE ALTERNATE TEST AATCC 30, TEST III 1/." PARAGRAPH 4.4.5.1, AATCC 30, TEST 1 1/"

PAGE 9, TABLE II, FOOTNOTE 1/, DELETE IN ITS ENTIRETY AND SUBSTITUTE: "1/ A MINIMUM OF 5 SPECIMENS SHALL BE TESTED. THE SOIL SHALL BE MADE OF AN EQUAL BLEND OF GOOD TOPSOIL, WELL ROTTED AND SHREDDED MANURE, AND COURSE SAND."

PAGE 9, AFTER FOOTNOTE 1/ INSERT NEW PARAGRAPH: "4.4.5.1 LEACHING RESISTANCE. SPECIMENS TO BE TESTED FOR MILDEW AND ROT RESISTANCE SHALL BE SUBMERGED IN A SUITABLE TANK CONTAINING WATER AT A TEMPERATURE OF 80 DEGREES TO 85 DEGREES F (27 DEGREES TO 30 DEGREES C) AND ALLOWED TO REMAIN IMMERSED FOR A PERIOD OF 24 HOURS. WATER FLOW THROUGH A TUBE INTO A TANK IS ADJUSTED TO ENSURE A COMPLETE CHANGE OF WATER NOT LESS THAN THREE TIMES IN 24 HOURS. THE PH AND TEMPERATURE OF THE WATER IS RECORDED AND INCLUDED IN THE REPORT OF THE RESULTS."

(ref. T1488 - May 10, 2006)

THE FOLLOWING CHANGES USED FOR MULTICAM PATTERN ONLY DATED

13 NOVEMBER 2009.

CHANGES TO MIL-T-3530, THREAD AND TWINE, MILDEW RESISTANT OR WATER REPELLANT TREATED, DATED FEBRUARY 20, 1991

MULTICAM

WHEN CLASS 2 - MULTICAM PATTERN IS SPECIFIED IN THE CONTRACT OR ORDER, THE FOLLOWING CHANGES SHALL APPLY.

1. DELETE PARAGRAPH 3.9.3 MATCHING ENTIRELY AND CHANGE TO THE FOLLOWING:

3.9.3 MATCHING. THE COLOR OF THE TREATED THREAD OR TWINE SHALL BE A GOOD (GOOD IS DEFINED AS A PERCEPTIBLE NOT APPRECIABLE DIFFERENCE IN COLOR) MATCH TO THE STANDARD SAMPLE WHEN TESTED AS SPECIFIED IN 4.5.4.

2. ADD 4.5.4 VISUAL SHADE MATCHING:

4.5.4 VISUAL SHADE MATCHING EVALUATION. THE SAMPLE SHALL BE WOUND OR PREPARED FOR EXAMINATION IN A MANNER SIMILAR TO THAT FOR THE STANDARD SHADE SAMPLE. THE COLOR AND APPEARANCE OF THE TREATED THREADS OR TWINE SHALL MATCH THE STANDARD SAMPLE WHEN VIEWED USING THE AATCC EVALUATION PROCEDURE 9, OPTION A OR C, WITH SOURCES SIMULATING ARTIFICIAL DAYLIGHT D75 ILLUMINANT WITH A COLOR TEMPERATURE OF 7500 (± 200) degrees K ILLUMINATION OF 100 (+20) FOOT CANDLES, AND SHALL BE A GOOD MATCH TO THE STANDARD SAMPLE UNDER INCANDESCENT LAMPLIGHT AT 2856 (+200) degrees K.

SECTION D – PACKAGING AND MARKING

PRESERVATION/PACKAGING SHALL BE IN ACCORDANCE WITH ASTM-D3951-90

MARKING IN ACCORDANCE WITH MIL-STD-129

EACH TROUSER SHALL BE PACKED IN A CLEAR POLY BAG WITH REVERSE FLAP

CLOSURE, WITH TAGS/LABELS CLEARLY VISIBLE

12 TROUSERS OF ONE SIZE SHALL BE PACKED IN EACH SHIPPING CONTAINER

AS A MINIMUM, THE CARTON SHALL BE SINGLE-WALL with DOUBLE-WALL LINERS, GRADE 275, STYLE RSC; CLOSE CARTONS WITH GUMMED OR PRESSURE SENSITIVE

TAPE ONLY, NO STAPLES PERMITTED

ADDITIONAL PACKAGING IN ACCORDANCE WITH SECTION "D" OF SOLICITATION

PALLETIZATION AS SPECIFIED IN CONTRACT

INSPECTION AT SOURCE/ACCEPTANCE AT SOURCE

INSPECTION AT SOURCE/ACCEPTANCE AT SOURCE

(ref. T0008 - May 17, 2006)

52.246-4, 52.209-A ALT I, 52.209-4 ALT II - FIRST ARTICLE APPROVAL

(ref. T0016 - May 17, 2006)

WHEN A FIRST ARTICLE IS REQUIRED, THE SAMPLE SIZE SHALL BE 50

ALL 50 UNITS WILL BE INSPECTED FOR VISUAL EXAMINATION:

Level 2: AQL SHALL BE 2.5

EIGHT UNITS SHALL BE INSPECTED FOR DIMENSIONAL CONFORMANCE:

Level S-3: AQL SHALL BE 2.5

ANY DIMENSION NOT WITHIN THE SPECIFIED TOLERANCES SHALL BE CAUSE FOR

REJECTION OF THE FIRST ARTICLE.

THE DCMA QAR SHALL FURNISH THE CONTRACTING OFFICER THE RESULT OF THE FIRST ARTICLE INSPECTION. THE CONTRACTIMG OFFICER WILL MAKE A FINAL DETERMINATION OF THE ACCEPTANCE OF THE FIRST ARTICLE. PRODUCTION SHALL NOT PROCEED UNTIL THE FIRST ARTICLE APPROVAL HAS BEEN ISSUED BY THE CONTRACTING OFFICER.

THE CONTRACTING OFFICER WILL PROVIDE NOTIFICATION OF FIRST ARTICLE RESULTS.

52.209-9P02 WAIVER OF FIRST ARTICLE. NOTE: DO NOT USE WHEN CLAUSE 52.210-9P06 IS APPLIED.

(ref. T0029 - May 17, 2006)

52.246-11 HIGHER - LEVEL CONTRACT QUALITY REQUIREMENT (FEB 1999)

(ref. T0041 - Oct. 18, 2006)

GOVERNMENT LABORATORY TESTING OF COMPONENTS FOR ACCEPTANCE PURPOSE.

(ref. T0042 - May 17, 2006)

52.252-9P03 QUALITY SYSTEMS REQUIREMENTS, DPSCM 4155.3; NOV. 3, 1997.

DLAD 4155.2; QUALITY ASSURANCE PROGRAM FOR DLA INVENTORY CONTROL POINTS.

(ref. T0043 - Oct. 18, 2006)

52.246-9P04 SHADE EVALUATION OF CONTRACTOR FURNISHED MATERIALS:

SHADE SAMPLING IS APPLICABLE

(ref. T0045 - May 17, 2006)

52.246-15 CERTIFICATE OF CONFORMANCE

(ref. T0046 - May 17, 2006)

ADDITIONAL INFORMATION FOR ASL:

THE ACCEPTABLE SUPPLIER LISTING (ASL) AND QUALIFIED LABORATORY LISTING (QLL) ARE NO LONGER VALID DOCUMENTS AND WILL NOT BE PUBLISHED IN THE FUTURE. THE POINT OF CONTACT FOR QUESTIONS PERTAINING TO LABORATORIES AND SUPPLIERS IS THE PROCUREMENT BUYER, INDICATED IN THE SOLICITATION OR CONTRACT. QUESTIONS SHOULD BE PROVIDED IN WRITING TO THE DESIGNATED BUYER.

CLAUSE 52.246-9P44 IDENTIFICATION OF QUALIFIED LABORATORY AND SOURCE SAMPLING APPLIES.

(ref. T1920 - Oct. 18, 2006)

REVIEW OF THIS ITEM HAS DETERMINED THAT THE SPECIFICATIONS, STANDARDS, PRODUCT DESCRIPTIONS OR OTHER TECHNICAL DATA APPLICABLE TO THIS PROCUREMENT ACTION DO NOT REQUIRE THE USE OF CLASS I OZONE DEPLETING SUBSTANCES (ODS) OR ODC(S).

(ref. T6854 - Oct. 18, 2006)

252.211-7006 - RADIO FREQUENCY IDENTIFICATION (RFI) Required (ref. T8379; Nov. 08, 2006)