SOW_Retofit_Ford_F150.docx

Statement of Work Ford F150 Administration: BLM Nevada State Office Location BLM Carson City District Office

General:

The BLM Nevada, Carson City District Office has a requirement for the services and supplies to strip a current Law Enforcement Vehicles (LE), Dodge Power Wagon, and install the removed LE parts on a new 2021 Ford F-150. This requirement also includes the purchase and installation of new parts and supplies onto the new vehicle to retrofit them into LE vehicle specifications.

Travel:

Due to lack of Law Enforcement resources, the service area must be within 25 miles of the Carson City District Office unless all vehicles will be picked up and dropped off at no additional cost.

Current Vehicle Information:

New Vehicle Information:

Vehicle: 2021 Ford F-150

Notes on equipment for installations:

The equipment needed for installation will be a combination of new and reused parts. Items that will be reused from existing vehicle are noted below. There may be an unforeseen possibility that some of these items will not work with the new vehicle or are found to be in disrepair once they are removed from the old vehicle. Quotes are not required to reflect this possibility. The BLM will be responsible for the cost of a new part above and beyond the initial quote if any part is found to be unusable at the time of installation. However, the vendor will be required to notify the BLM of any unusable part, suggested replacement part, and obtain approval before purchase and installation.

For all new parts needed to complete the installation, as noted below, the vendor must include manufacturer, model, and itemized price of equipment in the quote. All new parts must meet the below set standards or specific make or model as noted or be equivalent. The BLM has the right to disqualify any part that is deemed not comparable or found to be unsatisfactory.

LED Red/Blue Lights: As noted below, for the LED Red/Blue lights the preferred manufacturers are SoundOff Signal or Code3. The preferred part is the SoundOff Signal model EMPS1STS3(X) or equivalent. Vendor will consult with BLM on preferred placement locations prior to installation.

Task 1: STRIP-EXISTING VEHICLE OF LAW ENFORCEMENT EQUIPMENT, Dodge Power Wagon (I620996)

· Remove Existing decals and brown striping

· Plug roof and body holes

· Ensure all OEM equipment and lighting are functioning

· Strip all law enforcement (Non-OEM) parts from truck

· Retain all useful parts for install into new vehicle (listed as PROVIDED below)

· All parts not re-used will be returned to BLM

Task 2: INSTALL LAW ENFORCEMENT EQUIPMENT ON NEW VEHICLE, 2021 Ford F150

· BUMPER

· Remove front OEM bumper (OEM bumper will be returned to BLM)

· Install new bumper (Iron Bull or equivalent) with OHV and Red/Blue light strip and a winch mount

· FRONT GRILL/ FRONT QUARTER PANEL

· Install- Front LED driving lights x2 and light bar x1on front bumper

· Install –Two forward facing LED light heads (red/blue with clear lens, see above for note on preferred make and model) with mounts behind grill (PROVIDED)

· Install - Two side facing LED light heads, surface mount / low profile lights (red/blue with clear lens, see above for note on preferred make and model) on left and right front quarter panel (PROVIDED)

· Install- Two Single Row LED Flood /Driving (Combo) Lights LED (Minimum: 4500lumen, IP67 rated minimum) behind grill (PROVIDED)

· Install –Siren 100w or greater speaker behind grill or compatible location. (PROVIDED)

· Install- Two Hide a Blast LED inserts in fog light housing (PROVIDED)

· Install -Wig-Wag Flasher Control for high beam headlights (PROVIDED)

· Install- Quick disconnect jumper cables and smaller air compressor plug to bumper- wired to protect emergency lighting and OEM electrical system (PROVIDED)

· Install 10,000 lb winch (synthetic rope) in front bumper

· TAILGATE/REAR QUARTER PANEL

· Install -Two Hide a Blast RED LED Inserts in taillights (PROVIDED)

· Install - Two red/blue LED lights surface mount / low profile (red/blue with clear lens, see above for note on preferred make and model) mounted to rear tailgate (PROVIDED)

· Install - Two red/blue LED lights surface mount / low profile (red/blue with clear lens, see above for note on preferred make and model) mounted to rear side quarter panels (PROVIDED)

· ROOF

· Install - Code 3 light bar OR equivalent with full front white abilities (scene lighting)

· Install Motorola Radio Antenna (PROVIDED)

· Install Cellular Booster Antenna (PROVIDED)

· Install Sat Rad GPS dome/disc Radio system antenna (PROVIDED)

· INSIDE WINDSHIELD / DASH

· Install – Cellular Booster 4G/5G

· Install– One LED Dome light (red/white). Overhead center console in driver area (PROVIDED)

· Install – Speaker microphone clip mount (x1) to dash/console (PROVIDED)

· Install --magnetic clip mount x2 on SatRad hand-held microphone and Radio microphone (PROVIDED)

· CENTER CONSOLE

· Install - Floor plate between seats for mounting console

· Install – Center Console unit with Ticket book/cup holder (preferably Troy)

· Install – Console armrest

· Install – Wiring for Motorola XTL8000 mobile radio (Face plate will be mounted on console, remote radio head will be mounted behind front passenger seat attached to prisoner cage) (PROVIDED)

· Install wiring for Satellite Radio / mic. Mic and crossband mounted on console

· Install – Leave Additional Space/plates for additional radio(s), if applicable.

· Install - Single Unit Siren control box with PA mic/system (PROVIDED)

· Install – Flexible LED Map light (red/white) mounted to console (PROVIDED)

· Install– Wiring for Satellite Radio / mic. (Mic and cross band will be mounted on console, main radio system will be mounted behind front passenger seat mounted on prisoner cage (PROVIDED)

· Install – Disable switch for rear brake and reverse lights.

· Install – Control Switches for accessories on or near console: (PROVIDED)

· Front off-road driving lights

· Rear brake light/reverse light cutouts

· Rear Prisoner Light

· Gun Locks

· Alley Lights

· Takedown Lights

· Directional Bar (back of existing Code3 Light Bar)

· Install - 12 volt, 3 plug auxiliary power ports x 3

· Install- 12-volt power invertor (PROVIDED)

· Install – Flush mount 2 port USB charge socket (PROVIDED)

· Install –Ignition override / “Secure Idle” switch with button installed at front top of center console or on dash (Unless equipped with similar feature from manufacturer)

· Install – Stream light Flashlight and Charger (PROVIDED)

· Install – Hidden ignition kill switch

· Install – Computer Dock and console computer mount for a 11-15” laptop (Havis platform or similar)

· ENGINE COMPARTMENT or VEHICLE INTERIOR

· 911circuits. (http://www.911circuits.com/ch15-1) or equivalent.

· Install - Charge guard system to prevent battery drain when minimum voltage is reached (minimum voltage has ability to start truck)

· Install - Circuit breaker, with ability to disconnect emergency equipment from OEM electrical system

· Provide Master auxiliary power/fuse block or box for all aftermarket electronics to access fuses (all fuses labeled) that is easily accessible. (can be mounted in vehicle interior if necessary) (PROVIDED)

· Install Remote vehicle start

· Install larger Transmission cooler if available

· BEHIND CONSOLE

· Install – Rifle and shotgun custom mount and 2 locks (BlackRac Locks) with a 10 second timer. Some modification may be necessary to current gun racks for mounting (PROVIDED)

· Install – double gun lock switch that control both gun locks, with one switch hidden near passenger seat and one switch on top of console (can be part of single unit siren control box). Additionally, gun locks disabled without key in ignition

· PRISONER TRANSPORT CAGE The preferred product to accomplish the following is manufactured by https://setina.com/partitions/single-prisoner-partition/#, OR equivalent.

· Install- Single prisoner transport cage in right rear passenger seat position, to include installation of steel window barriers on all windows accessible from transport cage.

· Install Setina Cargo Deck with drawer on left rear passenger area

· Disable all interior door handles and window switches accessible from the transport

· Cage (Right rear passenger door lock and window controls), but leave operable from driver door controls.

· Install- Rear / downward facing white LED flush / low profile mounted into prisoner cage. (PROVIDED)

· FRONT WINDOW/WINDSHIELD

· Install – 30% High quality Window tinting on front driver and passenger side windows.

· Install – 30% High quality Visor strip window tint on windshield.

· REAR BED

· Install – Cross bed toolbox

· Install – Spare tire mount

· VEHICLE EXTERIOR

· Install vinyl decals and brown stripe on exterior of vehicle (PROVIDED).

· Install side rock slider/running boards

· Install full skid plate available for F150