Attachment_6_MSGQ_Specifications_EN_REV._1_JULY_14_2017.pdf

US Milan Consulate MSGQ Renovation Project

Milan US Consulate MSGQ Renovation Project

Specifications Tecnical sheets

JUNE 06, 2017

REV. 1 JULY 14 2017

AMERICAN CONSULATE GENERAL MILAN

MARINE QUARTERS

SPECIFICATION FOR THE INSTALLATION OF A NEW FIRE ALARM SYSTEM.

The MSGQ on the 7th floor of the Consulate General Milan, on Largo Donegani 1, must be protected with a fire alarm that must comply with the most stringent code between the NFPA 72 and the local UNI 9795.

The contractor shall submit shop drawings for approval, based on equipment from the “Notifier” manufacturer, for a full addressable system.

Contractor shall also provide final commissioning and instruction for 4 hours to the consulate staff.

The fire alarm shall consist of, but shall not be limited to the following:

Smoke detectors for the protection of the space above the false ceiling, where electric and mechanical systems are installed. The smoke detectors in this area shall be provided with an indicator that will provide visual signaling to below the false ceiling. Material type Notifier NFXI-OPT plus INDICATOR. Estimated quantity: 20

Smoke detectors in each bedroom below false ceiling with audible base, type NFXI-OPT with base BSO-PP-102. Estiamted quantity: 7

Smoke detectors for the common areas, below false ceiling, type NFXI-OPT. Estimated quantity: 13

Temperature rate protection for the kitchen, type NFXI-TFIx58. Estimated quantity: 1

Manual pull stations, type addressable P700. Estimated quantity 4

Visual and audible panels type PAN1-EU (certified European). Estimated quantity 4

Output modules for the connection of the fire alarm with the building notification system, type M701. Estimated quantity: 5

Fire panel controller, fully addressable, 2-loop class A, type AM2000. Quantity 1

Connection of devices with shielded cable 0.75 sq.mm. Stranded flexible copper, insulation PVC, jacketing PVC with an operating voltage U0/U = 450/750 V. Code compliance CEI 20/29 and IEC 60228

All cables shall be run inside electrical metal tubing (EMT) size 32 mm. Conduit shall run above false ceiling with metal junction boxes.

ChiminelG Typewritten Text

ChiminelG Typewritten Text

CATALOG CUTS

D-197.1-AM2000N-ENG Rev. A.4 06/2011

ANALOGUE CONTROL PANEL

AM2000

DESCRIPTION

AM2000N is a microprocessor analog control panel for fire alarm systems management, developed in compliance with EN-54.2 and EN-54.4 regulations.

This control panel has 2 analog loops that can manage 99 detectors and 99 modules each, for a total of 198 detectors and 198 i/o modules. The control panel is also programmable through PK2000 pc software, that allows: configuration, storing and printing.

Available, on request, with MODBUS protocol.

MAIN FEATURES

■ Microprocessor-based system

■ 2 analogue communication loops

■ Each line can manage 99 detectors + 99 input/output modules

■ Graphic backlit LCD display 8 lines, 40 columns

(240X64 dots).

■ 2 serial interfaces in standard version:

- 1 RS-485 interface to connect up to 16 repeaters LCD6000N/T and LCD6000A;

- 1 RS-232 interface predisposed for PK software.

■ 4 access levels designed according to EN-54.2 and EN.54.4 standards.

■ 3 password levels (Operator - Maintenance - Configuration).

■ Configurable descriptions: 32 characters for point; 32 characters for zone description.

■ 150 physical zones and 400 logic groups.

■ User-programmable CBE (Control-by-event) equations to program actions to be performed, using logic operators (And-Or-Xor-Delay-etc.).

■ History log 999 events in non volatile memory.

■ Real time watch.

■ Self loop configuration with self device recognition.

■ Software functions configurations for in field devices.

■ Auto-recognition of points with the same address.

■ Alarm and fault management.

■ Programmable detectors alarm threshold.

■ Detector clean alarm signalling.

■ Low sensitivity detector signalling.

■ Automatic night/day mode.

■ WalkTest function for each zone.

■ Keyboard with specific function keys: evacuation, delay reset, buzzer mute, sounder silence/restore, reset.

■ Alphanumeric keys for in field configuration.

OUTPUTS

■ Supervised sounders output.

■ Voltage free contacts relay output:

- general alarm;

- general fault.

POWER SUPPLY

Control panel is powered by mains and in mains fault condition it will continue normal operation, thanks to batteries.

Mains requirements:

■ Voltage: 230 Vac single-phase -15% ÷ +10%.

■ Frequency: 50 / 60Hz.

■ Current: 0,5 A.

■ Power supply 24Vcc (27.6Vdc -10% ÷ +2% ripple max. 100mVpp) 2,1A tot, (panel’s power, user output, power supply for analog devices on loop).

■ User output for auxiliary loads; in example:

bells, sounders, etc.

■ Battery charger:

- Output voltage: 27,6Vdc

- Output current: 1A - ripple max 100m Vpp

(with temperature compensation)

- Batteries: 2 x 12V 18 Ah max.

- Signalling: Low batteries, charger fault, battery fault.

ENVIRONMENTAL FEATURES

■ Temperature range: - 5° C + 40° C.

■ Humidity: 10 93 % (without condense).

■ Stock temperature: - 10° C + 50° C.

MECHANICAL FEATURES

■ Weight: 6 Kg.

■ Dimensions: 267 x 483 x 111 mm.

D-197.1-AM2000N-ENG Rev. A. 4 06/2011

ANALOGUE CONTROL PANEL

AM2000

SISTEMA GESTIONE

QUALITÀ E AMBIENTE

CERTIFICATI

UNI EN ISO 9001:2008

UNI EN ISO 14001:2004

NOTIFIER ITALIA S.r.l. - A socio unico - 20097 San Donato Milanese (Ml) - Via Grandi, 22 - Tel.: 02/518971 - Fax: 02/5189730 - E-mail:

notifier@notifier.it Capitale Sociale € 2.700.000,00 i.v. - C.C.A.A. 1456164 - Trib. Milano Reg. Soc. 348608 - Vol. 8549 Fasc. 8 - Partita IVA IT 11319700156 (informativa privacy art. 3 Digs 196/03) - Ufficl Regionali: 10143 Torino – Corso Potenza, 6 - Tel.: 011/0650611 - Fax: 011/4531183 - E-mail: notifier.torino@notifier.it - 35010 Limena (PD) Via IV Novembre, 6/c Int. 9 - Tel.: 049/7663511 - Fax: 049/7663550 - E-mail:

notifier.padova@notifier.it - 40050 Funo di Argelato (BO) - Asta Servizi, Bl. 3B, Gall. B n. 85, Centergross - Tel.: 051/864855 - Fax: 051/6647638 - E-mail:

notifier.bologna@notifier.it - 50136 Firenze –Via Aretina, 167/M Tel/Fax: 055/289177 - 00118 Roma - Via Del Casale Santarelli, 51 - Tel.: 06/7988021 - Fax: 06/79880250 - E-mail: notifier.roma@notifier.it - 80143 Napoli - Palazzo Prof. Studi - Centro Direzionale, Isola E2, Scala B, Piano 5° - Tel.:

081/7879398 - Fax: 081/7879159- E-mail: notifier.napoli@notifier.it - 70125 Bari - Via Delia Costituente, 29 - Tel.: 080/5013247 - Fax: 080/5648114 - E-mail:

notifier.bari@notifier.it - 95128 Catania - Viale Alcide De Gasperi, 187 - Tel.: 095/7128993 - Fax: 095/7120753 - E-mail: notifier.catania@notifier.it www.notifier.it

Tutti i dati sono soggetti a cambiamento senza preavviso. Tutti i diritti di questa pubblicazione sono riservati.

PK2000

PK2000 is a PC software for AM2000N control panel, and allows to:

■ Transfer and show control panel’s configurations on

PC.

■ Transfer programs from PC to control panel.

■ Create and manage a file-archive with configurations, editable in any moment and transferable to the control panel

The programming functions that can be realized by using this software are the same the user can carry out working on the control panel.

PK software is Windows XP compatible.

The communication between control panel and PC is realized through RS232 serial port.

OPTIONAL BOARDS

SIB600W:

Microprocessor-based communication board for new concentration system. SIB600W is equipped with Ethernet port (LAN TCP/IP) and USB port for PC and printer. SIB600W is linkable with all compatible external devices.

SIB600OEM:

Microprocessor-based communication board, endowed with an RS232/485 output for connection with NOTI- FIRE-NET-2000N with CEIABI protocol or MODBUS on request (only for fire system).

LCD PANELS REPEATER

Remote panels with LCD display for NOTIFIER AM Series remote management.

Panels and annunciator are endowed with backlit graphic LCD display 320x240 dots. Repeaters are characterized by high brightness and contrast that assure clear view in any light environment condition.

The connection with panels is performed by RS-485 connection.

LCD-6000-N

Fire repeater.

LCD-6000-N is endowed with seven keys that allow navigation through different menus and execution of system management functions: silent, reset, disablement and lamp test.

LCD-6000-A

Zone programmable repeater.

LCD-6000-A shows active panel events with relative devices or zones. The zone displayed are configured by PC with PK software.

LCD-6000-T

Technologic alarm repeater and Gas detection.

Specific to display gas detection related events and 420mA technologic events. LCD-6000-T is equipped with 3 additional LEDs for pre-alarm and alarm levels.

D-532.1-NFX-ENG Rev. A.1 10/2009 Analogue Temperature Sensors

NFX Series - T

DESCRIPTION

New Series NFX is the latest generation of the addressable fire detectors develop by Notifier NFX Series offers cost savings for installers, enhanced configurability, management and outstanding detection performance and false alarm immunity for end users. All of the new benefits are delivered while maintaining full electrical and mechanical backwards compatibility with previous versions to support existing systems. NFX Series has a new protocol that delivers more devices on the loop and gives greater control, configurability and device management whilst enabling the overall system to be optimised to the location and use of the bulding with far grater flexibility than even before.

The compatibility with previous protocol, that can manage up to 99+99 addresses, is ensured (AM2000N, AM4000 e AM6000N). The detector used with this control panel provide the same functionality as 700 Series. Additional features allowed by the new protocol will be available on a new range of control panel of upcoming production.

MAIN FEATURES

• 58°C & 78°C fixed temperature and rate of rise heat detectors.

• Available with or without Isolator module

• Tri colour LED offering red, green and amber colours

• Rotary decade address switches

• Pure white colour to compliment modern buildings

• Inctudes Series 700 Advanced Protocol

• 100% mechanical and electrical backwards compatibility

• New Base design to compliment the detector.

The NFX-TFIX58 and NFX-TFIX78 are fixed temperature analogue addressable sensors employing low mass thermistors and microprocessor technology far fast response and linear temperature sensing. The NFX-TDIFF uses the same thermistor and microprocessor technology to provide an alarm when the rate of rise in temperature exceeds 10.C/minute or if the temperature exceeds a threshold of 58°C. Detectors has two integrai tri-colour LEDs that provide 360° local visual indication ofthe device status. NFX-T conforms to EN54-5.

The new digital protocol provides reduced power consumption across the loop and enables up to 159 devices and modules per loop.

All detectors are environmentally friendly and meet the WEEE and RoHS legislative requirements, minimising end of lite disposal costs.

TECHNICAL FEATURES

• Voltage range: 15 to32Vdc

• Stanby current:

200µA @ 24Vdc (no communication) 300µA @ 24Vdc (LED blink 5Hz) 3.5mA @ 24Vdc LED red 7.0mA @ 24Vdc LED green 10.5mA @ 24Vdc LED amber

• Temperature range: -30°C to +70°C

• Humidity: 10 to 93% (without condensate)

• Height: 61mm installed in B501AP

• IP Rating: IP30 (IP33 with WB-1AP)

• Diameter: 102mm

• Weight: 88g

• Wiring: 2,5mmq

• Colour: white

• Material: PC/ABS

0786-CPD-20659 0786-CPD-20660 0786-CPD-20661

NFX-TFIX58 NFX-TFIX78 NFX-TDIFF

0786-CPD-20653 0786-CPD-20654 0786-CPD-20655

NFXI-TFIX58 NFXI-TFIX78 NFXI-TDIFF

NOTIFIER ITALIA S.r.l. - A socio unico - 20097 San Donato Milanese (Ml) - Via Grandi, 22 - Tel.: 02/518971 - Fax: 02/5189730 - E-mail:

notifier@notifier.it Capitale Sociale € 2.700.000,00 i.v. - C.C.A.A. 1456164 - Trib. Milano Reg. Soc. 348608 - Vol. 8549 Fasc. 8 - Partita IVA IT 11319700156 (informativa privacy art. 3 Digs 196/03) - Ufficl Regionali: 10151 Torino - Via Pianezza, 181 - Tel.: 011/4531193 - Fax: 011/4531183 - E-mail: notifier.torino@notifier.it - 35010 Limena (PD) Via IV Novembre, 6/c Int. 9 - Tel.: 049/7663511 - Fax: 049/7663550 - E-mail:

notifier.padova@notifier.it - 40050 Funo di Argelato (BO) - Asta Servizi, Bl. 3B, Gall. B n. 85, Centergross - Tel.: 051/864855 - Fax: 051/6647638 - E-mail:

notifier.bologna@notifier.it - 50136 Firenze –Via Aretina, 167/M Tel/Fax: 055/289177 - 00118 Roma - Via Del Casale Santarelli, 51 - Tel.: 06/7988021 - Fax: 06/79880250 - E-mail: notifier.roma@notifier.it - 80143 Napoli - Palazzo Prof. Studi - Centre Direzionale, Isola G1, Scala D, Piano 15° - Tel.:

081/7879398 - Fax: 081/7879159- E-mail: notifier.napoli@notifier.it - 70125 Bari - Via Delia Costituente, 29 - Tel.: 080/5013247 - Fax: 080/5648114 - E-mail:

notifier.bari@notifier.it - 95126 Catania – Viale Alcide De Gasperi, 187 - Tel.: 095/7128993 - Fax: 095/7120753 - E-mail: notifier.catania@notifier.it www.notifier.it

Tutti i dati sono soggetti a cambiamento senza preavviso. Tutti i diritti di questa pubblicazione sono riservati.

D-532.1-NFX-ENG Rev. A.1 10/2009 Analogue Temperature Sensors NFX Series - T

SISTEMA GESTIONE

QUALITÀ CERTIFICATO

UNI EN ISO 9001:2000

MOUNTING BASES

• B501AP: base standard white backward compatible withe (RII200)

• B524RTE-W: base with relay (RII62RLAP)

ACCESSORIES

• WB-1AP: anti-water cover cap for base and detector white

(RII76AP)

• SMK400EAP:

surface mounting kit to interface pipeline bases white (RII71AP)

• RMK400AP: flush mounting kit white (RII72AP)

TEST ACCESSORIES

• SOLO-100: 4,5mt telescopic tube (ACI100)

• SOLO-101: 1mt extension for

SOLO-100 (ACI101)

• SOLO-461: Thermal detector test tool with battery (ACI104)

• SOLO-424: 220V test tool for thermal detectors (ACI105)

• SOLO-200: Universal extraction tool (ACI106)

• SOLO-610: Tool bag for accessories (ACI107)

• SOLO-713: Accessory for magnet (ACI713)

• 1001-001: Kit for detector test smoke + temperature (includes 1 test unit, 1 TS3-001 smoke capsule, 2 batteries and 1 battery charger) (ACI110)

• 2001-001: Kit for detector test smoke + temperature + CO (includes 1 test unit, 1 TS3-001 smoke capsule, 1 TC3-001 CO capsule, 2 batteries and 1 battery charger) (ACI111)

MODELS

MODEL DESCRIPTION STOCK

CODE

NFX-TFIX58 58°C fixed temperature detector RIL403

NFX-TFIX78 78°C fixed temperature detector RIL404

NFX-TDIFF Rate of rise detector RIL402

NFXI-TFIX58 58°C fixed temperature detector with isolator RIL413

NFXI-TFIX78 78°C fixed temperature detector with isolator RIL414

NFXI-TDIFF Rate of rise detector with isolator RIL412

COMPATIBILITY WITH EXISTING PRODUCTS

BASES:B501: base standard h 18,5mm

B501DG: as base B501 alta 26mm B524IE: base with isolator module B524RE: base with relay output.

B501AP

SOLO-461

2001-001

NOTIFIER ITALIA S.r.l. - A socio unico - 20097 San Donato Milanese (Ml) - Via Grandi, 22 - Tel.: 02/518971 - Fax: 02/5189730 - E-mail:

notifier@notifier.it Capitale Sociale € 2.700.000,00 i.v. - C.C.A.A. 1456164 - Trib. Milano Reg. Soc. 348608 - Vol. 8549 Fasc. 8 - Partita IVA IT 11319700156 (informativa privacy art. 3 Digs 196/03) - Ufficl Regionali: 10151 Torino - Via Pianezza, 181 - Tel.: 011/4531193 - Fax: 011/4531183 - E-mail: notifier.torino@notifier.it - 35010 Limena (PD) Via IV Novembre, 6/c Int. 9 - Tel.: 049/7663511 - Fax: 049/7663550 - E-mail: notifier.padova@notifier.it - 40050 Funo di Argelato (BO) - Asta Servizi, Bl. 3B, Gall. B n. 85, Centergross - Tel.: 051/864855 - Fax: 051/6647638 - E-mail: notifier.bologna@notifier.it - 50136 Firenze –Via Aretina, 167/M Tel/Fax: 055/289177 - 00118 Roma - Via Del Casale Santarelli, 51 - Tel.: 06/7988021 - Fax: 06/79880250 - E-mail:

notifier.roma@notifier.it - 80143 Napoli - Palazzo Prof. Studi - Centro Direzionale, Isola E2, Scala B, Piano 5° - Tel.: 081/7879398 - Fax: 081/7879159- E-mail: notifier.napoli@notifier.it - 70125 Bari - Via Delia Costituente, 29 - Tel.: 080/5013247 - Fax: 080/5648114 - E-mail: notifier.bari@notifier.it - 95128 Catania - Viale Alcide De Gasperi, 187 - Tel.: 095/7128993 - Fax: 095/7120753 - E-mail: notifier.catania@notifier.it www.notifier.it

Tutti i dati sono soggetti a cambiamento senza preavviso. Tutti i diritti di questa pubblicazione sono riservati

D-305.1-P700-ITA-ENG Rev. A.4 11/2010 Indoor analog addressable manual call point

P700

SISTEMA GESTIONE

QUALITÀ E AMBIENTE

CERTIFICATI

UNI EN ISO 9001:2008

UNI EN ISO 14001:2004

DESCRIPTION

Indoor analog glass-break P700 button has been designed to be used for manual alarm point for fire systems.

Compatible with all NOTIFIER’s analog control panels, P700 has a rotary-switch for communication loop addressing and double insulator, one in input and one in output that can be excluded through dip-switch.

MAIN FEATURES

Easy to use Addressing through dip-switch Double bi-colour LED; it shows different states Plug terminals for easy cabling Easy test procedure, through suitable key Break glass with fluorescent protective film Wall or flush mounting into Bticino B503 box Wall-mount base supplied with the button

APPLICATIONS

It can be used for commercial, industrial or residential applications. It’s used as manual alarm point in case of fire. It’s usually installed outside doors in order to be easy to access in case of room evacuation.

INSTALLATION

An included suitable plastic box is used for wall-mounting. P700 can also be flush-mounted into Bticino B503 box. Package also includes screws for flush-box fixing. Cabling is easy thanks to plug terminals, as shown in figure.

TECHNICAL FEATURES

Operating voltage: 1532Vdc Standby current without communication @ 24Vdc:

390µA Absorption with communication every 5 sec and LED enabled @ 24Vdc: 560µA Absorption with communication every 5 sec and insulator disabled @ 24Vdc: 590µA Insulator response time after short-circuit: 300µsec Reset time after short-circuit removal: 150µsec Protection grade: IP30 (indoor applications only) Operating temperature: -10° +55°C Relative humidity: 10% - 93% (without condensate) Weight: 146gr. (with bottom 213gr.)

Max number of buttons on each line: 99 max Colour: red

DIMENSIONS

PRODUCTS

ACI150 P700 analog button ACI151 P700 replacement glass, 10 pieces

107m

107m

50mm

0051-CPD-0282

Article Number K5191

ULTRA FLAT

Rectangular acrylic tray 180x80cm

I dea l S tandard – V id ima AD • 53 Mar in Popov S t r . • 5400 Sev l i evo • Bu lga r ia • Te l : 00 359 675 30468

Rectangular acrylic tray 180x80cm Low height 4 cm Suitable for floor-standing or floor recessed installation Matching waste, supplied separately

Recommended equipment:

- Universal support legs for shower trays K712667

- MEPA-Set installation girder for shower trays K725567

- Fixation legs set K936067

- Siphon for Acrylic Shower Tray Ø90 mm TEMPOPLEX K7817AA

VARIANTS

Rectangular acrylic tray 90x75cm K5179 Rectangular acrylic tray 120x80cm K5182 Rectangular acrylic tray 180x90cm K5192 Rectangular acrylic tray 160x80cm K5187 Rectangular acrylic tray 120x100cm K5184 Rectangular acrylic tray 140x80cm K5185 Rectangular acrylic tray 140x90cm K5186 Rectangular acrylic tray 100x80cm K5180 Rectangular acrylic tray 170x90cm K5190 Rectangular acrylic tray 160x90cm K5188 Rectangular acrylic tray 120x90cm K5183 Rectangular acrylic tray 170x80cm K5189 Rectangular acrylic tray 100x90cm K5181 Rectangular acrylic tray 80x90cm K5178

REQUIRED

Shower tray drain waste J3417

RECOMMENDED

Universal support legs for shower trays K7126

FINISHES*

* 01 = Euro White

Metal product q-clip system Square tiles

:::: 3

Q-clip SYSTEM SQUARE TilES

BENEFITS

n concealed grid system for a monolithic ceiling surface n Downwardly demountable with the use of an extraction tool for access to the ceiling void.

n cost effective n Solution with optional swing-down

“Window” function

APPLICATION AREA

n Used in a variety of ceiling areas:

from small service rooms to large commercial office buildings and major transportation terminals.

pRojEcT: GGZ oost Brabant (Nl) :::::::: ARchiTEcT: MAS Architectuur

SPECIFICATION

System Armstrong ceiling system Q-clip, clip-in solution with concealed grid, with optional swing-down “Window” function, suspension height min. 100 mm

Tile material galvanised steel sheet 0.5 mm (aluminium or further materials on request) coating RAl 9010 pure white post-coated powder painted visible surface, other RAl or NcS colours on request

Execution* Q-clip: square tile square edged Q-clip F: square tile bevel edged 3 mm

Gap solution 0 mm gap, without gasket

Acoustic inlay Black non-woven acoustic fleece as standard. other options available on request.

Standard modules Q-clip:

600 x 600 mm 625 x 625 mm Q-clip F:

500 x 500 mm 600 x 600 mm 600 x 300 mm (no “Window” function) 625 x 625 mm 625 x 312.5 mm (no “Window” function)

Grid system U-profile + Dp12 A-Bar, security clip optional available, further suspension methods on request

* For further information about the edge detail execution of metal tiles, please see the Metal Edge Detail Execution datasheet perimeter solution Range of standards trims in steel and aluminium plus custom bulkheads available.

Service integration standard round or rectangular cut-outs plus customized options on request.

Special capabilities - secured exterior ceiling solution

- seismic ceiling solution

- clean room ceiling solution

- can be combined with other Armstrong products

STANdARd PERFORATION PATTERNS

Ultra Microperforation Rg 0501 hole diameter: 0.5 mm open area: 0.64 %

Extra Microperforation Rg 0701 hole diameter: 0.7 mm open area: 1.5 %

Microperforation Rd 1522 hole diameter: 1.5 mm open area: 22%

Standard Perforation Rg 2516 hole diameter: 2.5 mm open area: 16%

Other perforation patterns available on request.

antonello Evidenziato antonello Evidenziato antonello Evidenziato antonello Evidenziato

4 :::: :::: 5

CROSS-SECTION Q-CLIP

LONgITUdINAL-SECTION Q-CLIP

U-profile perimeter trim threaded rod M6 expansion bolt M6 clamping bracket

Dp12 A-Bar ceiling void visible sidesquare tile system Q-clip threaded rod M6 wall anchor hanger for Dp12 A-Bar expansion bolt M6

U-profile perimeter trim

M/2 clamping bracket

Dp12 A-Bar square tile system Q-clip plug-in clip visible side ceiling void extraction tool

Item No. designation

BpM 300100 U-profile

BpM 300119 connector for U-profile

BpM 300120 plug-in clip

BpM 300140 wall anchor

BpM 300121 clamping bracket

BpM 311111 expansion bolt M6 x 30 mm

BpM 311099 threaded rod M6 x 1‘000 mm

BpM 311022 Dp12 A-Bar

BpM 300138 connector pin for Dp12 A-Bar

Item No. designation

BpM 300105D hanger for Dp12 A-Bar

BpM 311303 hexagonal bolt M6 x 16 mm

BpM 311103 hexagonal nut M6

BpM 311305 washer M6 18 x 1.6 mm

BpM 300106 security clip

BpM 311028 extraction tool

BpM 311027 hinge-down bracket for Window function

BpM 300157 security clamp for Window function

M = module size / A = tile length / B = tile width

ACOUSTIC PERFORMANCE

Metal ceiling systems have been tested for their acoustic performance of sound absorption. All perforated products can be supplied with a variety of factory fitted acoustic infill options.

please contact us for more information.

ThERMAL CONdUCTIvITy

(λ) W/mK

50.0 : Steel

0.04 : Acoustic fleece hUMIdITy ExPOSURE

Up to 95% Rh (for short term exposure).

SERvICES INTEgRATION

Metal panels can be supplied with factory produced cut outs and apertures for the integration of building services equipment.

CLEANINg

Dust should be removed from the painted surface by wiping with a clean soft cloth. More stubborn marks should be removed with a mild household detergent in warm water.

Excessive use of water should be avoided. The use of abrasive cleaners of the painted surface is not recommended.

COLOUR

Standard colours RAL 9010 20% gloss

Global White 12% gloss

RAL 9006 30% gloss

RAL 9007 30% gloss

Special colours other RAl and NcS colours available on request

QUALITy STANdARd

Armstrong is a certified EN ISO 9001:2008 Quality Assumed Manufacturer. All Armstrong ceiling and grid systems are manufactured to the relevant tolerances and quality standards appropriate to material. Where differences exist between this and any expressed or implied architectural specificaitons or requirements then Armstrong’s manufacturing standards will prevail unless stated otherwise.

ENvIRONMENTAL our metal panels have an average of up to 30% recycling content. our European manufacturing plants are certified to:

ISO 14001:2004 + Cor. 1:2009 Armstrong is a member of TAiM (Technical Association of industrial Metal ceilings).

Sustainability Acoustics Safe & healthy

Recycled content light reflectance aw up to sound absorption class

NRc up to

Dncw / Dnfw (dB) up to

Rw (dB) up to

Fire reaction Humidity Resistance (%) up to cleanability Bioguard paint option scratch resistance

ISO 14021

Ultra Microperforation Rg 0501 (1) up to 30 83 0.45(l) D 0.55 18 8 A1 95 scrubbable ✔ ✔

Extra Microperforation Rg 0701 (2) up to 30 80 0.55(l) D 0.65 21 10 A2-s2, d0 95 wipeable moist cloth (3) ✔ ✔

Microperforation Rd 1522 (2) up to 30 65 0.70 c 0.70 16 6 A2-s2, d0 95 wipeable moist cloth (3) ✔

Standard perforation Rg 2516 (2) up to 30 70 0.75(l) c 0.80 18 8 A2-s2, d0 95 wipeable moist cloth (3) ✔ plain / Unperforated (1) up to 30 85 0.10(l) Not classified 0.10 44 19 A1 95 scrubbable, high pressure water cleaning (4)

(1) RAl 9010 colour, without acoustic inlay. (2) RAl 9010 colour, with black acoustic fleece glued on rear. (3) Wipeable moist cloth for preforated tiles with fleece. Scrubbable for plain tiles or perforated tiles without fleece.

(4) only for plain clip-in systems with silicone sealed joints (reduced water pressure to the minimum).

RAL 9010 Global White RAL 9006 RAL 9007

M/2

6 :::: :::: 7

CROSS-SECTION Q-CLIP F

LONgITUdINAL-SECTION Q-CLIP F

U-profile perimeter trim threaded rod M6 expansion bolt M6 clamping bracket

Dp12 A-Bar ceiling void visible sidesquare tile system Q-clip F threaded rod M6 wall anchor hanger for Dp12 A-Bar expansion bolt M6

U-profile perimeter trim clamping bracket

Dp12 A-Bar square tile system Q-clip F plug-in clip visible side ceiling void extraction tool detail A Q-clip square tile detail B Q-clip F square tile

Dp12 A-Bar connector pin for Dp12 A-Bar connector for U-profile detail C grid solution clamping bracket expansion bolt M6 threaded rod M6 plug-in clip hanger for Dp12 A-Bar

U-profile hexagonal bolt M6 hexagonal nut M6 washer M6 wall anchor plug-in clip swing-down “Window” function hinge-down bracket and security clamp for “Window” function

M = module size / A = tile length / B = tile width detail E suspension methods clamping bracket with threaded rod

U-profile hanger with threaded rod combi Nonius hanger with Nonius to part combi Nonius hanger with eye wire detail d security clip security clip

Dp12 A-Bar square tile system Q-clip

For further information about the edge detail execution of metal tiles, please see the Metal Edge Detail Execution datasheet

M/2

M/2

/2

PA

S

A rm st ro ng B ui ld in g

P ro du ct s

R C

S B es an ço n

B

P rin te d on c hl or in e fr ee p ap er

WesteRN euRope Belgium & Luxembourg Armstrong Building products B.V.

Bureaux commerciaux Belgique postbus 3803 4800 DV Breda Nederland Tel.: (+32) 02 223 00 72 Fax: (+31) 076 521 04 07 e-mail: benelux-info@armstrong.com www.armstrong-plafonds.be germany & Switzerland Armstrong Building products Kundenservice office Building Quadrium claudius prinsenlaan 126 4818 cp Breda Niederlande Tel.: (+49) 0251 7603 210 Fax: (+49) 0251 7603 593 e-mail: deutsche-info@armstrong.com www.armstrong-decken.de www.armstrong-decken.at www.armstrong.ch

Armstrong Metalldecken AG Breitfeldstrasse 8 9015 St. Gallen Switzerland Tel.: +41 (0) 71 313 63 63 Fax: +41 (0) 71 313 64 00

Zentralschweiz Armstrong Metalldecken AG Büro / lager Zentralschweiz Grossweid 9 ch-6026 Rain Tel.: +41 (0) 41 921 63 63 Fax: +41 (0) 41 921 63 80

Suisse Romande Armstrong plafonds Métalliques SA Bureau Suisse Romande 3, rue Gustave-Monynier ch-1202 Genève Tel.: +41 (0) 22 731 60 70 Fax: +41 (0) 22 731 60 74

Austria Armstrong Metalldecken Gmbh Bundesstrasse 70 A-6830 Rankweil Tel.: +43 (0) 55 22 34 44-0 Fax: +43 (0) 55 22 34 44-8

Armstrong Metalldecken Gmbh Messendorferstrasse 6 A-8041 Graz Tel.: +43 (0) 31 64 71 584 Fax: +43 (0) 31 64 71 584-10

Spain & Portugal Armstrong Building products SAS immeuble paryseine 3, allée de la Seine 94854 ivry-sur-Seine cedex France – Alcobendas Madrid Tel.: (+ 34) 91 352 53 17 Fax: (+ 34) 91 350 20 15 e-mail: info-espana@armstrong.com www.armstrong.es/techos

France & French Speaking Africa Armstrong Building products SAS Bureaux commerciaux France immeuble paryseine 3 Allée de la Seine 94854 ivry-sur-Seine Tel.: 0800 41 36 43 Fax: (+33) 1 45 21 04 11 e-mail: info-france@armstrong.com www.armstrong.fr/plafonds

Siège social Armstrong Building products SAS 67 rue de Salins – cS 20089 25302 pontarlier cedex France

Italy & greece Armstrong Building products Ufficio commerciale italia immeuble paryseine 3 Allée de la Seine 94854 ivry-sur-Seine Francia Tel.: (+39) 02 66 22 76 50 Fax: (+39) 02 66 20 14 27 e-mail: info-italia@armstrong.com www.armstrong-soffitti.it www.armstrong.eu

Netherlands Armstrong Building products B.V.

Verkoopkantoor Nederland postbus 3803 4800 DV Breda Nederland Tel.: (+31) 076 52 30 200 Fax: (+31) 076 521 04 07 e-mail: benelux-info@armstrong.com www.armstrong.nl/plafonds

United Kingdom Armstrong World industries ltd Building products Division Armstrong house 38 Market Square Uxbridge UB8 1NG Tel.: 0800 371849 Fax: (+44) 1895 274287 e-mail: sales-support@armstrong.com www.armstrong-ceilings.co.uk

Republic of Ireland Armstrong World industries ltd.

108 Greenlea Road Terenure co Dublin 6W ireland Tel.: 1800 409002 Tel.: (+353) 1 499 1701 Fax: (+353) 1 490 7061 e mail: sales-support@armstrong.com www.armstrong-ceilings.ie ceNtRal euRope NoRtH (dK/EE/FIN/IS/LT/Lv/N/PL/S) Armstrong Building products BV Sp. z o.o. oddział w polsce

ul. Domaniewska 37 02-672 Warszawa poland Tel.: (+48) 22 337 86 10/ 86 11 Fax: (+48) 22 337 86 12 e-mail: service-ce@armstrong.com latvia: www.armstrong.lv lithuania: www.armstrong.lt Norway: www.armstrong.no poland: www.armstrong.pl Sweden: www.armstrong.se ceNtRal euRope soutH (AL/BA/Bg/CZ/hR/hU/KO/ Md/ME/MK/RO/RS/SK/SI) Armstrong Building products lighthouse building, jankovcova 1569/2c, 170 00 praha 7, czech Republic Tel. : +420 234 700 543 e-mail: service-ce@armstrong.com czech Republic: www.armstrong.cz hungary: www.armstrong.co.hu Romania: www.armstrong.ro Serbia: www.armstrong.rs Slovakia: www.armstrong.sk Slovenia: www.armstrong.si easteRN euRope

CIS

Armstrong Moscow Gmbh park place, office E502 # 113/1, leninsky prospekt Moscow 117198 Russia Tel.: (+7) 495 956 5100 Fax: (+7) 495 956 5101 e-mail: info-cis@armstrong.com Russian Federation: www.armstrong.ru miDDle east / aFRica / tuRKey Armstrong World Industries Ltd Africa Middle East Turkey division Armstrong house 38 Market Square Uxbridge UB8 1NG Tel.: (+44) 01895 202097 Fax: (+44) 01895 272928 e-mail: sales-support@armstrong.com www.armstrong.eu israël: www.armstrong.co.il South Africa: www.armstrong-ceilings.co.za dubai | United Arab Emirates Armstrong World industries jlT office No. 2003, 20th Floor Gold crest Executive Tower jumeirah lakes Towers p.o. Box 73831 Dubai, U.A.E.

info-me@armstrong.com www.armstrong.ae

Turkey Armstrong Europa Gmbh Mimar Sinan Mah. Mimar Sinan 35/2 cekmekoy istanbul Türkiye Gsm: +90 542 772 49 22 Gsm: +90 544 293 5931 www.armstrong.com.tr etulpar@armstrong.com

ULTIMA+

www.armstrong.eu

EN ISO

7724-2 & 3

87%

EN ISO

14021

50-55% www.armstrong.euPlease contact our Armstrong Technical Sales Group for further details.

1.0

0.8

0.6

0.4

0.2 a P

125 250 500 1 000 2 000 4 000

ULTIMA+

Recycled Content Light Reflectance Intelligibility

Octave Band centre frequency (Hz)

P C

A rm st ro ng B ui ld in g

P ro d uc ts

R .C

.S . B es an ço n

B

P rin te d in E

.C . o n ch lo rin e fr ee p ap er fr om s us ta in ab le r es ou rc es

P E

FC

/1

0-

-1

EN ISO 354 &

EN ISO 11654

EN ISO 10848-2

& EN ISO 717-1

EN ISO 140-3

& EN ISO 717-1

Prelude XL2/TLX 24 mm Prelude XL2/TLX 24 mm Prelude XL2/TL 15 mm Prelude XL2 24 mm Prelude Main Runner System Z System Z Prelude Sixty2 24 mm Prelude Sixty2 24 mm Silhouette XL2 15 mm Prelude Sixty2 24mm - Prelude Sixty2

Interlude XL2 15 mm Main Runner 24 mm

ULTIMA+ BoARd TEgULAR MICRoLook 90 VECToR SL2 k2C2

Board & Tiles

500 x 500 x 19 mm 7673 M

600 x 600 x 19 mm 7661 M 7664 M 7674 M 7681 M

625 x 625 x 19 mm 7661 D 7664 D 7674 D 7681 D

625 x 1250 x 19 mm 7663 D

675 x 675 x 19 mm 7662 M 7665 M 7675 M

600 x 1200 x 19 mm 7663 M 7666 M 7677 M

300 x 1200 x 19 mm 7676 M

Planks

300 x 1500 x 19 mm 7699 M

312.5 x 1500 x 19 mm 7667 D

300 x 1720 x 19 mm 7700 M

300 x 1800 x 19 mm 7701 M

312.5 x 1800 x 19 mm 7668 D

300 x 2500 x 19 mm 7702 M

312.5 x 2500 x 19 mm 7669 D

EN 12667

& ISO 8301

l = 0.052 W/m K 5.2 kg/m2 (Board,Tegular, MicroLook)

5.8 kg/m2 (Vector)

5.6 kg/m2 (SL2/K2C2)

95 % RH

Dnfw

36 dB (Board, Tegular, MicroLook 90) 33 dB (Vector) 40 dB (SL2, K2C2)

Rw

18 dB (Board, Tegular, MicroLook 90) a w NRC 125 250 500 1000 2000 4000 Hz Board, Tegular, MicroLook 90

0.70(H) 0.75 0.40 0.50 0.65 0.85 0.95 1.00 a P

Vector 0.75(H) 0.75 0.35 0.55 0.65 0.80 0.95 0.90 a P

SL2, K2C2

0.65(H) 0.65 0.35 0.45 0.55 0.75 0.90 1.00 a P

Sound Absorption Class = C

19mm

4.5mm

19mm 8mm

9.5mm

19mm 8mm

15°

6mm

10mm

2mm m m m m

586mm 575mm

594mm10mm m m

575mm

594mm

RUS KM1 (G1, V1, D1, T1) EEA Euroclass A2-s1, d0

FZ 123EN 13501-1

15 YEAR

guarantee

30 YEAR

system guarantee

ISO 14644-1

ISO 5

A B m m

13mm

26mm

11.5mm11.3mm

9mm 12mm m m

9.5mm

BRONZE

Knauf Metal Stud Partitions

The structural, statical properties, and characteristic building physics of Knauf systems can solely be ensured with the exclusive use of Knauf system components, or other pro-ducts expressly recommended by Knauf.

Technical Data Sheet W11 Edition 2005-07

W111 Knauf Metal Stud Partition - single metal stud frame, single layer cladding W112 Knauf Metal Stud Partition - single metal stud frame, double layer cladding W113 Knauf Metal Stud Partition - single metal stud frame, triple layer cladding W115 Knauf Metal Stud Partition - double metal stud frame, double layer cladding W116 Knauf Installation Wall - linked double metal stud frame, double layer cladding W118 Knauf High Security Wall - single metal stud frame, triple layer cladding + metal sheet K234 Knauf Fireboard Wall A1 - single metal stud frame, single layer Fireboard cladding

Knauf Metal Stud Partitions W11 Technical Data / Sound Protection / Thermal Insulation

W111 Metal Stud Partition

System spacing of studs

62.5 cm spacing of studs

62.5 cm spacing of studs

62.5 cm single metal stud frame - single layer cladding

1) mm W/(m²K)

W112 Metal Stud Partition

12.5

125 100

40 0.66

0.65 0.50

0.65 0.49 0.40 single metal stud frame - double layer cladding

W115 Metal Stud Partition double metal stud frame - double layer cladding

105155

155205

205255

2x 12.5 48

59 2x40 0.37

3 61 2x60 0.27

0.21

3)

75 50

100 75

125 100

12.5 25.5Piano F 47

45 40 0.66

0.65 0.50

0.65

0.40 0.49

2x 12.5

2x 12,5

46.5 h D d d

GKF

d h D d d d h D

For legend see page 3

Piano

Sound Shield

GKB / GKF

GKB

GKB

GKF

GKB

GKF

105155

205 155

255 205

2x 12.5 49.5

2x40

2x60

2x80

0.37

0.27

0.21

KNAUF

Piano F Piano

Sound Shield

GKB / GKF

KNAUF

Piano F Piano

Sound Shield

GKB / GKF

KNAUF

Notes and sound protection proofs see page 3

58 60

2x80 80 0.37

0.47

Technical data dimensions wall

D h cladding d ness type weight kg/m² thick-approx.

stud (ca-vity) mm mm mm thick-ness

Sound

R dB proof

2) w,R protection

ThermalIn-sulation nominal thickness

U value insul.

0.38 0.47 0.60

0.47 0.60

0.61

0.60

0.38 0.46

0.47 0.60

0.61 antonello Evidenziato

>>Non Rettificato Not Rectified Nicht Kalibriert Non Réctfié

/Concept Gres porcellanato Porcelain Feinsteinzeug Grès cérame

61,5x61,5 24”x24”Superficie Naturale Natural surface Natur Oberflache Surface Naturelle

Gres porcellanato

Rettificata

Porcelain

Rectified

Feinsteinzeug

Kalibriert

Grès cérame

Rectifie

Керамогранит

Ректифицированная

Concept EN 14411 APPENDICE G BIa GL

White

Concept White 60120 Nat65

Concept Cream 60120 Nat65

Concept White 60120 Lux90

Concept Cream 60120 Lux90

60x120 - 24”x48”

60x120 - 24”x48”

Concept White 6060 Nat83

Concept Cream 6060 Nat83

Concept White 6060 Lux86

Concept Cream 6060 Lux86

Concept White 6060 Nat Nr57

Concept Cream 6060 Nat Nr57

Concept White 2060 Lux61

Concept Cream 2060 Lux61

60x60 - 24”x24” 61,5x61,5 - 24”x24”Nr

60x60 - 24”x24” 61,5x61,5 - 24”x24”Nr

20x60 - 8”x24”

20x60 - 8”x24”

Concept White 3060 Nat56

Concept Cream 3060 Nat56

Concept White 3060 Lux58

Concept Cream 3060 Lux58

30x60 - 12”x24”

30x60 - 12”x24”

Cream

Concept White 4590 Nat61

Concept Cream 4590 Nat61

Concept White 4590 Lux63

Concept Cream 4590 Lux63

45x90 - 18”x36”

45x90 - 18”x36”

Concept Beige 60120 Nat65

Concept Pearl 60120 Nat65

Concept Beige 60120 Lux90

Concept Pearl 60120 Lux90

60x120 - 24”x48”

60x120 - 24”x48”

Concept Beige 6060 Nat83

Concept Pearl 6060 Nat83

Concept Beige 6060 Lux86

Concept Pearl 6060 Lux86

Concept Beige 6060 Nat Nr57

Concept Pearl 6060 Nat Nr57

Concept Beige 2060 Lux61

Concept Pearl 2060 Lux61

60x60 - 24”x24” 61,5x61,5 - 24”x24”Nr

60x60 - 24”x24” 61,5x61,5 - 24”x24”Nr

20x60 - 8”x24”

20x60 - 8”x24”

Concept Beige 3060 Nat56

Concept Pearl 3060 Nat56

Concept Beige 3060 Lux58

Concept Pearl 3060 Lux58

30x60 - 12”x24”

30x60 - 12”x24”

FOR

prodotto ad emissioni totalmente compensate Production process with total emissions compensation Produktionsverfahren mit vollständiger Emissionskompensation Processus de production avec émissions totalement compensées произведено при полностью компенсированных выбросах

10mm Nat

Nat

Lux

Lux

61,5x61,5 - 24"x24"

61,5x61,5 - 24"x24"

White- Cream Grey - Pearl - Beige

White- Cream Grey - Pearl - Beige

Dark

Dark

Concept Beige 4590 Nat61

Concept Pearl 4590 Nat61

Concept Beige 4590 Lux63

Concept Pearl 4590 Lux63

45x90 - 18”x36”

45x90 - 18”x36”

Beige

Pearl antonello Evidenziato

34 35

Flexi B Green Mat, Flexi 2 Orange Mat Flexi Technic 4B White

36 37

Flexi Technic A White

CSAFTAWH00

Flexi Technic A Greige

CSAFTAGR00

Flexi Technic A Black

CSAFTABL00

Flexi Technic A Grey

CSAFTAGY00

Flexi Technic 4A White

CSAFT4AW00

Flexi Technic 4A Greige

CSAFT4AG00

Flexi Technic 4A Black

CSAFT4AB00

Flexi Technic 4A Grey

CSAFT4AY00

Flexi Technic B White

CSAFTBWH00

Flexi Technic B Greige

CSAFTBGR00

Flexi Technic B Black

CSAFTBBL00

Flexi Technic B Grey

CSAFTBGY00

Flexi Technic 4B White

CSAFT4BW00

Flexi Technic 4B Greige

CSAFT4BG00

Flexi Technic 4B Black

CSAFT4BB00

Flexi Technic 4B Grey

CSAFT4BY00

Gres porcellanato

Rettificata

Porcelain

Rectified

Feinsteinzeug

Kalibriert

Grès cérame

Rectifie

Керамогранит

Ректифицированная

FLEXIBLE ARCHITECTURE TECHNIC

EN 14411 APPENDICE G BIa UGL

White Greige

Black Grey

TECHNIC

FLEXI TECHNIC A - 4B

FLEXI TECHNIC B - 4A

60x60 - 24"x24" 10mm antonello Evidenziato antonello Evidenziato

Cod. GES06.BI Colonna sospesa. Peso 5 kg.

Wall-hung pedestal. Weight 5 kg.

Cod. GE005.BI Colonna a terra. Peso 12 kg.

Floor mounted pedestal. Weight 12 kg.

GENESIS LAVABO GE070.BI

Cod. GE070.BI Lavabo 70 monoforo. Con foro troppo pieno. Installazione sospesa.

Completo di fissaggi. Peso 22 kg.

Basin one tap hole 70cm, provided with overflow hole.

Wall-hung installation. Fixing kit included. Weight 22 kg.

Cod. PG070CR cromato / chromium-plated

Cod. PG070BO bianco lucido / shiny white

Porta asciugamani Towel rail.

GENESIS LAVABO 70 x 50 GE070 CON MANIGLIONE PG070

GENESIS LAVABO 70 x 50 GE070 CON MANIGLIONE PG070

GENESIS LAVABO 70 x 50 GE070 CON MANIGLIONE PG070

GENESIS LAVABO 70 x 50 GE070 CON MANIGLIONE PG070 antonello Evidenziato

Z93057

Asta murale da 800 mm.,flex. 1500 mm.

Slide rail length 800 mm, flex. 1500 mm

Simply Beautiful

75 mm.- 2 15/16”

18 mm.- 11/16” m m

/8 m m

5/

110 mm.– 4 5/16”

Simply connec ted.

Geberit Supply Systems

Geberit Supply Systems:

Lifelines for modern buildings.

A modern building works like a complex organism: it must be supplied with water, heat, energy and more. Geberit delivers the solutions that maintain its func-tions reliably and consistently:

drinking water, heating, cooling, gas, compressed air, etc.

– Geberit Supply Systems for residential buildings, industry and public buildings provide the con-fidence your customers expect from you.

Everything leakproof. Permanently.

1 Geberit pressing systems 6 – 7

2 Geberit Mepla 8 – 11

3 Geberit Mapress Stainless Steel 12 – 15 4 Geberit Mapress Carbon Steel 18 – 19 5 Geberit Mapress Copper 20 – 21 6 Geberit Mapress for gas, solar, saturated steam and industrial applications 22 – 23

7 Geberit pressing tools 24 – 25

Geberit pressing systems.

Safe and economical supply.

Safe and long-lasting connections are the primary goal in all areas of pipe installation. In addition, a quick and easy installation is important to the installer. The Geberit Mapress and Geberit Mepla pressing systems meet these requirements perfectly

They focus on reliability by providing mechanical strength and hydraulic tightness In Geberit press connections, the pipe is pushed into or onto pressfittings with the necessary insertion distance or the visible pipe insertion depth and then pressed using the pressing tool. By pressing the pressfitting and the pipe, the required mechanical strength is achieved. The permanent hydraulic tightness is obtained through the resilience of the O-ring. The established connection between press-fitting and pipe is permanent and length-ways non-positive. The pressing tool, which has been specially designed to suit Geberit supply pipes, ensures a precise, simple, and reliable pressing sequence.

Visibly safe during the pressure test Maximum safety for the installer is a top priority for our systems. For this reason, the unpressed joints of Geberit systems leak during the pressure test on them.

Defined leak paths ensure that leaks are visible. This applies to pressure tests with water as well as when pressure-testing with air. In addition, all pressfittings in Geberit Mapress range are equipped with a pressing indicator. As a result, non-pressed connections can be easily identified even before the pressure test is carried out.

Almost limitless application ranges Thanks to the variety of product materials and the wide range of pipe diameters and fittings available, the two pressing systems Geberit Mapress and Geberit Mepla cover almost every area of application in pipe installation. They can be used in anything from domestic installations with drinking water systems, heating systems and gas systems to special applications in industrial areas and in shipbuilding. The Mapress and Mepla systems are also suitable for chemical and thermal disinfection.

Trouble-free system transitions:

Everything fits together Transitions between different product materials and systems can be done without any problems thanks to the numerous adapters. For example, in heating installa-tions, Geberit Mapress Carbon Steel can be used for the basement distribution and the riser pipe and Geberit Mepla multilayer pipe system for the radiator connection – so there is no need for complicated sealing with hemp or the use of a threaded adapter.

Just insert – press – done.

The press connection ensures mechanical strength and hydraulic tightness.

The seal ring provides the pressing indicator with additional safety.

The pressing indicator on all Geberit Mapress pressfittings indicates unpressed connections

– even before the pressure test.

← Geberit Mapress is ideal for combining with other Geberit supply systems.

← The Geberit pressing tool and the associated pressing jaws or collars are coordinated perfectly with one another to create permanently leakproof and reliable connections.

→ Perfectly coordinated system with fitting, pipe and pressing tool with pressing jaw or collar

→ Three metallic pressing systems and the Geberit Mepla multilayer pipe system offer precision-fitting and economical solutions for a wide range of requirements

→ Strictly implemented quality requirements ensure permanently leakproof connections

→ Safety when processing: unpressed connections are immediately visible

→ Flexibility and economic efficiency thanks to systems that can be combined with one another

→ The pressing tool, which has been specially designed to suit Geberit supply pipes, ensures a trouble-free and reliable pressing procedure

Geberit Mepla.

Safe – simple – economical.

The Geberit Mepla multilayer pipe system combines the characteristics of synthetic product materials with those of metals in an extraordinary way.

The multilayer pipe, which consists of an inner pipe made of PE-RT, an aluminium pipe and a protective PE-RT layer on the outside, allows for easy, safe and flexible processing, whilst also complying with strict hygiene standards. The fittings, made of PVDF, gunmetal and brass, ensure a high degree of safety during processing as well as reliable tightness. These charac-teristics make Geberit Mepla especially well suited to potable water supplies and radiator connections.

Three layers for the perfect system in potable water and heating applications The outer plastic layer, made of PE-RT, protects against corrosion and mechanical influences, while the butt-welded aluminium layer in the middle makes the pipe stable yet bendable and forms a barrier against diffusion. The inner layer, which is also made of PE-RT, is corrosion-resistant and food-safe. With its resistance to pressure far beyond the standard testing pressure of 15 bar, the multilayer pipe is truly robust.

Geberit Mepla can be used for all potable water qualities in accordance with country-specific potable water ordinances

– previous analysis of the drinking water is not required.

The connection for safe drinking water installations Geberit Mepla is equipped with three safety precautions. The pipe insertion depth, which is always visible, indicates the correct position of the pipe on the fitting.

The bead on the fitting helps position the tool and ensures a precise pressing operation. Finally, unpressed connections can be clearly identified during the leak test. In addition to the fittings made of PVDF, a wide assortment of fittings made of gunmetal or brass is available for threaded connections.

Economical processing thanks to system technology The quick and safe connection technology as well as the bendable product material make Geberit Mepla an economical supply system. Clever connections such as the MeplaFix adapter ensure a quick connection to Geberit installation elements. The Geberit Mepla adapter T-piece to MeplaFix facilitates the loop-through processing method. This method saves pipe material, fittings and installation time. These savings can result in a cost benefit of up to 20%.

The Geberit Mepla adapter to Geberit Mapress allows Geberit Mepla and Geberit Mapress to be combined.

Hygienic down to the finest detail Geberit Mepla fittings and pipes are equipped with protection plugs. To ensure the highest possible degree of potable water hygiene, the protection plugs are only removed shortly before installation.

The loop-through option that can be used when installing potable water pipes with Geberit Mepla adapter T-pieces to MeplaFix reduces the stagnation of tap water, thus providing an effective contribution to preventing potable water contamination.

The hemp-free connections also have a positive impact on potable water hygiene.

→ Safely sealed, Geberit Mepla pipes stay hygienically clean until they are installed.

← Geberit Mepla fittings: perfect hygiene characteristics thanks to protection plugs.

→ Inherently stable, bendable and corrosion-resistant

→ Proven press connection without sleeve, precise pressing operation due to bead on fitting

→ Non-pressed connections are visibly leaky

→ High resistance to pressure

→ Pipes and fittings are hygienically sealed

→ Can be chemically and thermally disinfected

→ Suitable for any potable water quality; no drinking water analysis required

→ Adapters to all Geberit installation elements

→ Adapters for quick connection to Geberit Mapress

D N

D im e n si o n

P e rm is si b le o p e ra ti n g te m p e ra tu re f o r d ri n k-in g w at e r

P e rm is si b le o p e ra ti p e ra tu re f o r h e at in g

P e rm is si b le o p e ra ti p re ss u re

Unit mm °C °C bar

12 16 x 2.25 0–70 0–85 10

15 20 x 2.5 0–70 0–85 10

20 26 x 3.0 0–70 0–85 10

25 32 x 3.0 0–70 0–85 10

32 40 x 3.5 0–70 0–85 10

40 50 x 4.5 0–70 0–85 10

50 63 x 4.5 0–70 0–85 10

65 75 x 4.7 0–70 0–85 10

D ri n k in g w at e r

H e at in g

G as

S p ri n k le rs

E xt in g u is h in g w at e r

C o m p re ss e d a ir

S o la r sy st e m s

H e at in g o il

V ac u u m in st al la ti o n s

O p e n w at e r c ir c u it s

R ai n w at e r

Tr e at e d w at e r

In d u st ri al p la n ts

Mapress Stainless Steel ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕

Mepla ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ Mapress Carbon Steel ✕ ✕ ✕

Mapress Copper ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕

* Only for wet extinguishing water pipes (non-drinking water)

** Dry compressed air

*** Possibly with additional corrosion protection measures; only with carbon steel pipe, outside zinc-plated

Geberit Mepla.

Easy to handle.

The Geberit Mepla assortment leaves little to be desired: pipe dimensions from 16 to 75 mm with or without preinsulation and a wide selection of around 300 fittings made of PVDF, gunmetal or brass allow the system to be used very flexibly.

Geberit Mepla is more corrosion-resistant and lighter than metal pipes, and more inherently stable and robust than plastic pipes. Therefore it can be bent and processed easily and safely. These advantages alone put the case for Geberit Mepla. Installers bend the pipes with a dimension of up to 20 by hand and connections up to a dimension of 26 can be pressed with the Geberit Mepla hand-operated pressing pliers. Plus, the convenient hand-operated pressing pliers offer noticeable advantages in processing situations with limited space. In heating installations, Geberit Mepla ticks all the right boxes with clever fittings such as the T-piece crossing for connecting to two pipes installed parallel to one another without intersecting.

One system. One tool. One warranty.

With Geberit Mepla, you only need one system for the potable water and heating supply. But above all, you only need one processing tool.

Simple fire protection solution With the fire protection pipe shells manufactured by Rockwool and Armacell, ceiling and wall feed-throughs can be created quickly, easily and economically.

At the same time, they meet the insulation requirements of potable water installations.

Moreover, short minimum distances allow for smaller duct dimensions.

Choose Geberit Mepla and you are choosing to be ecologically responsible Geberit Mepla is 97% recyclable, separated into aluminium and plastic.

Insert

Debur and calibrate

Bend

Cut

Press – done!

↓ Loop through potable water hygienically and economically: adapter T-piece with MeplaFix adapter.

→ Comprehensive assortment: Dimensions from 16 to 75 mm

→ Dimensions of up to 20 mm can be bent by hand

→ Dimensions from 16 to 26 mm can be processed with hand-operated pressing tools

→ Simple fire protection…