ORDERING DATA.pdf
PDF 106 KB Posted
- Attached to
- BEARING, STAVE SHAPE Federal contract opportunity
- Solicitation number
- SPMYM2-24-Q-1034
About this file
This document contains an ordering data sheet and related federal contract opportunity solicitation. The ordering data sheet provides specifications for Class III stave bearings to be supplied under the contract. Requirements include manufacturer identification and date markings on the bearings, dimensions per drawing 803-1385664 Rev H, storage and shelf life per MIL-DTL-17901C, and preservation, packaging and packing levels A per MIL-DTL-2845E. The related solicitation is for stave shaped bearings to be acquired from a sole source supplier by the Defense Logistics Agency Maritime Puget Sound Naval Shipyard according to FAR Parts 12 and 13. Bids must include the completed solicitation, manufacturer, country of origin, and lead time for delivery FOB destination. The NAICS code is 336612 and the PSC is 2010.
View the file
Other files for this federal contract opportunity
| File | Type | Posted |
|---|---|---|
| QPL.pdf | ||
| SOLE SOURCE.pdf | ||
| SPMYM2-24-Q-1034.pdf |
On GovTribe
Work with this file on GovTribe
- Download the original file
- Contacts named in this file
- Similar government files
- Ask GovTribe AI about this file
Text version
MATERIAL ORDERING DATA
IDN: N4523A 4064-1006
ICN: 38MNF24301 KO: H02 KOI: 002
Paragraph 6.2 Ordering data
a. MIL-DTL-17901C (SH), DETAIL SPECIFICATION, BEARING COMPONENTS,BONDED SYNTHETIC RUBBER, WATER LUBRICATED, dated 10 May 2005
b. Class III, stave bearing, nonmetallic back (Note: Class I replaced with Class III).
c. Product identification and marking requirements as follows: (The markings shall no interfere with the installation or performance of the bearing.)
Class II: Manufacturer identification, date of manufacture, size (outside diameter and inside diameter). The letters shall be at least 1/10 inch in height; stamped, etched, or engraved; and readily visible to the unaided eye. Flanged bearings are marked on the end of the flange; sleeved bearings are marked on the outside diameter.
Class III: Manufacturer identification, ‘use by’ month and year (i.e., 5-99), cross section size, and batch number, also special information such as “1/16 oversize” (for example: “RCN010A112 1/16 oversize”). The letters shall be at least ⅜ inch in height and readily visible to the unaided eye. Starting near one end of the stave the above information shall be stamped at 2-foot intervals along the back of the stave.
Class IV: Manufacturer identification, date of manufacture, size (outside diameter and inside diameter). The letters shall be at least 1/10 inch in height; permanent ink, stamped, etched, or engraved; and readily visible to the unaided eye. Sleeved bearings are marked on the outside diameter.
Class V: Manufacturer identification, date of manufacture, outside diameter, inside diameter, length, unique serial number with –1 or –2 for each half of a matched set. All information shall be permanent ink or engraved into the back of the bearing and shall be minimum of ½ inch in height.
d. Type NA (as identified in NAVSHIPS 803-1385664 - Bearings Stern Tube and Strut)
Size and tolerance: CLASS III #9 STANDARD, ROMOR X2, DIMENSIONS PERDWG 803-1385664 Rev H. TABLE III, LENGTH = 38.50 INCHES (+ 0 - 1/16”)
f. Storage and shelf-life requirements: PER PARAGRAPH 3.9 OF MIL-DTL-17901C
g. Quantity: 110
I. If Class V, provide dimensional requirements: Not Applicable for Class III
m. Levels of preservation, packaging, and packing required: PRESERVATION LEVEL A, PACKING LEVEL A, MARKING IN ACCORDANCE WITH MIL-DTL-2845E
Additional Data Requirements: N/A Prepared By: Michael Lee
Code: 260V
File details come from the government source that posted it. Updated .