Attachment_J-2_MIL-B-24480A.pdf

● MIL-B-24480A(SH)

20 June 1985”

SUPERSEDING

o iiL-B-24480(sHIPs) 30 January 1973

MIL-B-21230A

29 July 1960 (See 6.4 and 6.5)

MILITARY SPECIFICATION

BRONZE, NICKEL-ALUMINUM (UNS No. C95800)

CASTINGS FOR SEAWATER SERVICS

This specification Is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense.

1. SCOPE

1.1 =. This specification covers static and centrifugal castings of nickel-aluminum bronze (UNS No. C95800) having good corrosion resistance for general seawater applications.

2. APPLICABLE DOCUMENTS

2.1 Government documents.

2.1.1 Standards. Umless otherwise specified, the following standards of the issue listed in that issue of the Department of Defense Index of Speci-fications and Standards (DoDISS) specified in the solicitation form a part of this specification to the extent specified herein.

STANDARDS

MILITARY

MIL-STD-1OS - Sampling Procedures

Attributes.

MIL-STD-2L8 - Welding and Brazing

Qualification.

and Tables for Inspection by

Procedure and Performance

MIL-sTD-271 - NofidestructiveTesr.ing Requirements for Metals.

Beneficial commencs (recommendations, additions, deletions) and any pertinent data which nay be of use in improving this document should be addressed to:

Commander, Naval Sea Systems Command, SEA 55Z3, Department of the Navy, Washington, DC 20362-5101 by using the self-addressed Standardization Document Improvement Proposal (DO Form 1426) appearing at the end of this document or by letter.

SO DELIVERABLE DATA REQUIRED BY THIS DOCUiCiNT AF.U YECA DISTRIBUTION STATEXEYT A Approved for public release; distribution unlimited

Downloaded from http://www.everyspec.com

Ii i

I

I I

K2L-B-24480A(SE)

MILITARY (Continued) H2L-STD-278 - Fabrication Welding and Inspection; and Casting

I o 2nspectionand Repair’for Machinery,Piping .?nd Pre9sure Vessels in Navy.

(Copies of scmadards required by contractors acquisition functions should be obtained from the directed by the contracting officer.)

Ships of the United States in connection with specific contracting activity or as

2.1.2 Government publication. The following Government publication forms a part of this specification to the extent specified herein.

PUBLICATION

NAVAL SEA SYSTEMS COMMAND (NAVSSA)

0991-LP-023-3000 - Propeller Ship Bronze Strlightening and Weld Of.

(copies of standards and publications required by contractors in connection with specific acquisition functions should be obtained from the concraccing activicy or as directed by che concraccing officer.)

2.2 Other publications. The following documents form a part af this speci-ficaClonto the extent specified herein. The issues of the documents which are indicated as DoD adopted shall be the issue listed in the current DoDISS and the supplement chereco, if applicable. o

AMSRICAN SOCIETY FOR TESTING AND MATERIALS (AS’Lll) I B 148-82 - Standard Specification for Aluminum-Bronze Sand

Castings.

B 271-81 - Standard Specification for Copper-Base Alloy Centri-fugal Castings.

(Application for copies should be addressed co che American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.)

I (Industry association specifications and standards are generally available 1 for reference from libraries. They are also distributed among technical groups and using Federal agencies.)

2.3 Order of precedence. In the event of a conflict between the text of this specificationand the references cited here>n, the text of this speciii-cacion shall cake precedence.

3. .REQUIREMSNTS

3.1 First article. ‘.lenspecified (see 6.2.1), a sample shall be subjectec to first article inspection (see $.3 and 6.3).

MIL-B-24480A(SH)

3.3 Heat treatment. Castings shall be given a temper anneal heat treat-ment at 1250 ~ 50 degrees Fahrenheit (“F) for 6 hours, minimum. Cooling shall be by the fastest means possible that will not cause excess distortion or cracking. Propellercastingsehall be exempt from this requirement.

3.4 Casting repair. Weld repair of testings shall be performed in accor-dance with MIL-STD-278. Welding procedure qualification, prior to production welding, shall be in accordance with MIL-STD-248. Repair of propeller castings shall be in accordance with NAVSEA 0991-LP-023-3000.

3.k.1 Post+eld heat treatment. When weld repairs are made to the side of the casting coming into contact with seawater in service or the heat affected zone extends to within 1/4 inch of the seawater aide castings shall be post~eld heat treated by the same procedure used to comply with 3.3. Redetermination of mechanical properties is not required after post-weld heat treatment. Surfaces in contact with seawater shall be specified (see 6.2.1).

3.5 Identification markin~ Identification marking shall be in accordance with ASTM B 148, including supplemental requirement S4, except that this speci-fication number shall be used.

3.6 Chemical and mechanical property requirements. The chemical and mechanical property requirements shall be as epecified in ASTM B 148.

3.7 Nondestructive requirements. The nondestructive requirements shall be as specified by MIL-STD-278, or the contract or order (see 6.2.1).

3.8 meet the

4.

4.1 centract

Form and dimensions. The form and dimensions of the castings shall pattern or drawing specified (see 6.2.1).

QUALITY ASSURANCE PROVISIONS

Responsibility for inspection. Unless otherwise specified in the or purchase order, the contractoris responsible for the performance of all inspection requirements as specified herein. Except as otherwise speci-fied in the contract or purchase order, the contractor may use his OVIIor any other facilities suitable for the performance of the inspection requirements epecified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements.

4.2 Classification of inspection. The inspection requirements specified herein are classified ae follows:

(a) First article inspection (see 4.3).

(b) Quality conformance inspection (see 4.4).

4.3 First article inspection. First articleinspectionshall consistof the examinationsand tests as specifiedin 4.3.1 through 4.3.3.

4.3.1 Sampling for first article inspection. The first caszing submitted for inspection shall be considered the first article ~ample.

HIL-B-24480A(SH)

4.3.2 Radiographic inspection. The first article casting shall be radio-graphically inspected in accO$d=ce wfth MIL-STO-271 tO the accePtmce criteria specified in MIL-STO-278 of the criticality level specified (see 6.2.1).

L.3.3 Mechanical property test. Mechanical properties shall be determined on highly stressed regions of the casting as specified (see 6.2.1) and shall meet requirements as agreed upon between the Command or agency concerned and the contractor.

4.3.4 Basic foundry practices. The contractor shall maintain a record of the basic foundry practices (type of melting or refining unit, molding proc~ss, basicriggingdesign, location of risers and chills, and so forth) used in the first article casting and shall make no change thereto without the specific aPPrOval of the Command or agency concerned. The concraccor nay be required to perform specific first article tests and examinations to verify chat the change will not degrade casting quality.

4.3.5 First article test report. The contractor shall prepare a first article test report in accordance with the data ordering document included in the contract or order (see 6.2.2).

4.4 Quality conformance inspection. Castings shall be examined and tested in accordancewith 4.6.1 through 4.6.3.1 herein. If any specimen fails to cOn-form to the requirements of this specificatiOn, the entire 10C shall be rejected, except as specified in 4.6.1.

i+.k.l Certificationof quality compliance. A certificate Of quali~Y compliance shall be prepared for eaoh lot of material offered for acceptance (see 6.2.2). l%e certificate shall include actual data of specified chemica~ and mechanical tests. Qualitative results of nondestructive tests and ocher inspectionsor tests shall be recorded on the certificate. The certificate shall also state that each lot has been sampled, tested, and inspected in accordancewith this specification and meets all specification requirements.

The certificate shall be signed by a responsible represencaciveof the contractor.

4.5 Sampling for qualicv conformance.

4.5.1 Lot. A lot shall consist of all castings produced from one furnace or crucible=c. When two or more furnace melts or crucible melts, or both, are used co charge a ladle for pouring, the casting produced therefrom shall constitute a lot.

4.5.2 Chemical analvsis sam~le. A chemical analysis sample shall be obtained in accordancewith ASTM 3 148.

4.5.3 Mechanical test samvls. A mechanical C*SC sample for s:atic cascin’gs shall be obtained in accordancewith .ASTX9 148. The saaple for Cencrifu$al casc-in?s shail be obtained in accordance.wi:h.\STXB 27!. %schanical cast sazmies s:hallaccompany cie castings through che heat :reacment s?ecified :3 3.3.

MIL-B-24480A(SH)

4.5.5 Identification of test coupons. All test bars shall be identified with the proper heat or lot number.

4.5.6 Sampling for visual and dimensional examination. From each lot, ssmples shall be selected for visual snd dimsnsionx2 examination in accordance with MIL-STD-105 at inspection level I. The Acceptable Quality Level (AQL) shall be 4.0 percent defective.

4.6 Examinations and tests.

.4.6.1 Visual snd dimensional examination. Each of the ccstings selected in 4.5.6 shall be visually snd dimensionally examined for conformsnce with the requirements of ASTM B 148 and the casting drawing. AIIycasting in the lot containing one or more visual or dimensional defects shall be considered a defective item snd rejected. If the number of defective items found in the lot equals or exceeds the rejection number specified in MIL-STD-105, the lot shsll be rejected subject to the resubmittal provisions of MIL-STD-105.

4.6.2 Chemical and mechanical property tests. Chemical snd mechanical property tests shall be performed in accordance with ASTM B 148.

4.6.3 Nondestructive tests. The applicable nondestructive tests as speci-fied by MIL-STC-278, or the contract (see 6.2.1). shall be performed in accor-dance with MIL-STD-271.

4.6.3.1 Acceptance criteria. The nondestructive test results shall conform to the requirements of MIL-STD-278, or as specified (see 6.2.1). The system or catego~y of the casting shall be as specified (see 6.2.1).

4.7 Inspection of packagin~ Sample packagea snd packs, and the inspec-tion of the preservation-packaging, packing snd marking f or shipment snd storage shall be in accordance with the requirements of section 5 and the documents specified therein.

5. PACKACING

(The preparation for direct Covernmenc for delivery requirements specified herein apply only acquisition.)

5.1 Packaging. Packaging shall be in accordance with the levels speci-fied (see 6.2.1), as annotated under the supplementary requirements section of

AS’R4B 148.

6. NOTSS

6.1 Intended use. Bronze, nickel-aluminum castings are intended for seawater applications.

6.2 Ordering data.

6.2.1 Acquisition requirements. Acquisition documents should specify the following:

I

(a) (b) (c) (d)

(e)

(f)

(g) (h)

(i) f’fIL-B-24480A(sE)

Title,number,and date of this specification.

First article, if required (see 3.1).

What surfaces are in contact with seawater (see 3.4.1).

Nondestructive test requirements, if other than MIL-sTD-278 (see 3.7 and b.6.3).

Pattern or drawing number and condition, whether as cast or mac!!inedin accordance with ASTM B 148 (see 3.8).

Criticality level of MIL-STD-278 for nondestructive inspection requirements (see 4.3.2).

First article mechanical property test locations (see 4.3.3).

Acceptance criteria for nondestructive tests ocher than :0 MIL-STD-278 and systems or category of casting (see 4.6.3.1).

Level of packaging (see 5.1).

6.2.2 Data requirements. When this specification is used in an acquisi-tion which incorporates a DD Form 1423, Contract Data Requirements List (CDRL), the data requirements identified below shall be developed as specified by an approved Data Item Description (OD Form 1664) and delivered in accordance with the approved CDSL incorporated into the contracc. men the provisions of FAR 52.227-7031ire Invoked and the DD Form 1423 is not used, the data specified below shall be delivered by the contractor in accordance with the contract or purchase order requirements. Deliverable data required by this specification is cited in the following paragraphs.

Paragraph no. Data requirement title Applicable DID no. L?FlsQL ●

4.3.5 First article inspection DI-T-b902 —

report

4.4.1 Certification data/report UDI-A-23264 — I

(Data item descriptions related to this specification, and identified in section 6 will be approved and listed as such .inDoD 5000.19L., Vol. II, AMDL.

Copies of data item descriptions required by the contractors in connection with specific acquisition functions should be obtained from the Naval Publications and Forms Center or as directed by the concraccing officer.)

6.2.2.1 The data requirements of 6.2.2 and any task in sections 3, 4, or 5 of this specification required co be performed to meet a data requireunc may be waived by che contractingfacquisition accivicy “pen certification by the offeror chat identical data were submitted by che offeror and acceptad by the Governmentunder a previous cmcracc for identical i:em acquired to this specification. This does not apply to 5pecific data which nay he required for each contract regardless of whether an identical item has bee” supplied prev:.-o“sly (for example , test reports).

b.3 First article insDeccion. Invitations for bids should provide that the Govermenc reserves the right to wai,,e ct?s r.squire!cenc for Sanples for I firsr article ixpec:ion as co chose bidders offering a ?cocuc: .Jb.ici.has bean ~:evio”sl:.acgui:ec or :es:ed 5..:he Co,..e:n7.er.c, and chat 5:ddezs oifer:n: S.UC’2 pr.>duc:s, ‘.’ic,JishL3 rei::on such >Zoc”ctioc or ::s:, 3U5: :Ur:.i;h ?,Ji:er,ce .-.l::n:’he‘:::z,?.ac :e?ii:, :33,,22,. ““r ‘z’’ver3=e’=‘“’’’’;=’‘s “’segc’” “=’’’’’’” ‘“ ‘:” ●

MIL-B-244BOA(SH)

6.4 Propeller alloys. Propeller castings previously acquired to MIL-B-21230, alloy 1, are now acquired to this specification. Alloy 2 is no longer being used as propeller material.

6.5 Changes from previous issue. Asterisks are not used in this revision to identify changes with respect to the previous issue, due to the extensiveness of the changes.

Preparing activity:

Navy - SH (Project MECA-N11O) i’

I

I

~ANDARDIZATION COCUMENT IMPROVEMENT PROPOSAL

[SCeln$tmctimu - Rcvcrx Side]

DOCUMENT“UM8ER 2. 00 CUMENT TITLE

‘31L-B-24480 A(SH)

NAhIe OF suawrnrnc 0RGAN12A780ti 4 7YPC OF ORGANIZATION (#- -j

•1 VENDOR

❑ m,, .OOn E6.s(smwt, CW7. $1.*. ZIPCA. I

❑ Urn”,. cru”s”

•1 OTHEn (3X.1, %,: -

,Roe LEi4 AREAS

. ,.,.O? .0” N.--r .“. W.,.,.,:

,. .=.”.— w.,.,.,:

.. %.,0./..,,...4. ,., .-.”-”..! ,0.

. . ..”! :* 5., ”! -7:. I.u,. ,,”,. ,“,, - O.!,.. . I ,. won. -E, i,. o.c .“IJ, E” ,,..,. - .“.