Installation Path.pdf

Total estimated travel path: approximately 800 ft travel truck to lab with minimum clearance 52” at laboratory doors and one freight elevator. Surfaces are vinyl tiles, concrete, and granite.

About 10 turns, pivots, or shifts in direction required.

The loading dock (height 47”) is located in the basement level of Building 215.

Path from the truck through outer Steel Door (clear 121”) to interior loading dock is 28’.

Once inside, pivot 90° left, 14’ path to inner Steel Door (clear 108”).

Inner Steel Door to Double Door (clear 89”), path is 148’.

Path from double doors in basement of Building 215 to Basement of Building 217/219 is 45’ straight, a 20° right turn, a 12’ path, a 20° left turn, and a 54’ path.

Connecting hallwaty to Building 217/219 requires a 135° left turn.

Path is a 160’corridor with Storage items along left wall (narrowest clearance 76”) Path is then a turn 90 ° at an 8’ turning radius into Freight Elevator.

Freight elevator is 11.5’ deep, 13’ wide, load max > 13000 kg

Exit fright elevator on first floor into Building 217 turning right 180° at an 8’ turning radius Path is 14’ slightly to the left at 15° to align with double doors (clear 69”) Path is 67’ past double doors, turning 30° right, 13’ path, turning 30° left, 60’ path Pivot 90° left to hallway of the laboratory, 105’ path (min clearance 80”) Laboratory doors to be removed by NIST staff, (clear appx. 52”) Entrance to lab requires appx. 35° pivot to proceed through entrance.

Laboratory is 31’ x 23.5’ with 6’ 6” unistrut rack min clearance.

Align long axis of 17’ System inverted “L” with the 20’ of unistrut.

Unistrut is 3’ wide x 20’ long; 6” 6” minimum clearance Edge of 10’ x 5’ x 18” table roughly aligns with end of unistrut at left (required clearance 3’) edge of 5’ x 12’ x 18” table is offset 1’ such that table is centered with 3’ unistrut width.

Clearance around table approximately 3’ 6” (minimum of 3’ required) at far corner of 10’ x 5’ table.

It is anticipated that the tables enter the room on their sides (vertical to floor), to be flipped to orientation horizontal to floor. Mobile gantries for this purpose may be hindered by Unistrut above final table positions. Two zones where gantries would not be impeded are:

1) Near the lab entrance door, approximately 9.5’ deep x 17.5’ long, maximum and

2) Away from the door on the other side of the Unistrut, approximately 9’ deep x 25’ long, maximum.

FE

Double Door 89” clear

76” clear

156’ from 135° turn to freight elevator

~8’ turning radius

TH

IS

H

AL

LW

AY

L

EN

G

TH

N O

T

TO

S

CA

LE

9’ at 20°

Building 215 Basement Level

Building 217/219 Basement Level

135° turn

90° turn

60 feet

Double Door -stairs

FE

Narrowest Gap – 80”

Electrical panel, 17” from wall Pillar, 24” from wall

Emergency Eye Wash, 27” from wall

~60’

~67’

~13’ at 30°

~ 105’

~8’ turning radius

~14’ at 15°

FEFreight Elevator

Building 217 First Floot

LAB

60 feet

View is opposite of direction of travel

5’ x 12’ x 18”

5’ x 10 ‘ x 18” ft b uf fe r z on e

3.5 ft buffer zone

Unistrut minimum clearance 6’ 6”

5’ x 12’ x 18”

5’ x 10 ‘ x 18” ft b uf fe r z on e

3.5 ft buffer zone

(appx.) 9.5‘ x 17.5’ zone for mobile gantry

(appx.) 9‘ x 25’ zone for mobile gantry

All items and cabinetry against right wall will be removed, separate from this procurement, prior to table rigging.

All items and cabinetry against right wall will be removed, separate from this procurement, prior to table rigging.