3D_Printer_rev_27May16.docx

UNCLASSIFIED

Product Description Naval Special Warfare Command Objet 350 Connex 3 Production 3-Dimensional Printer Brand Name or Equal

1. BACKGROUND

1.1. Special Reconnaissance Team One, Technical Operations Troop requires the capability to test new technologies and equipment, and re-design of existing equipment. Prototyping using 3D technology provides this capability.

2. OBJECTIVE

2.1. To procure a commercially available 3D Printer with full-function fabrication capability to facilitate the development of new technologies, field existing technologies in new ways, and save on procurement costs by leveraging the prototyping capabilities of this technology.

3. DESCRIPTION OF REQUIREMENT

3.1. This requirement is for the procurement and installation of an Objet 350 Connex 3-3D Printer, Brand Name or Equal, with the following specifications:

3.1.1. Capability of producing horizontal build layers as fine as 16 microns (.0006 in.) for creating high density products.

3.1.2. Minimum Build Platform not less than (XYZ) >= 342 x 342 x 200 mm (13.4 x 13.4 x 7.9 in.)

3.1.3. Resolution X-axis: 600 dpi; Y-axis: 600 dpi; Z-axis: 1600 dpi

3.1.4. Accuracy 20-85 microns for features below 50 mm; up to 200 microns for full model size. Accuracy standards shall be achievable from design to actual product with minimal loss.

3.1.5. Prints rubberized polymers

3.1.6. Prints transparent ABS

3.1.7. Prints snap-fit capable polypropylene facsimiles

3.1.8. Prints Digital ABS™ for thin wall rigidity

3.1.9. Prints heat-tolerant materials for fittings

3.1.10. Uses full-cure photopolymer Water Jet removable support material

3.1.11. Prints paintable finish parts.

3.1.12. System Requirements

3.1.12.1. Workstation Compatibility with Windows 7/Windows 8

3.1.12.2. Able to accept STL files

3.1.13. Network Connectivity LAN TCP/IP

3.1.14. Power Requirements 110-240 VAC 50/60Hz; 1.5 kW single phase.

3.2. Installation and Training

3.2.1. Vendor shall provide factory authorized installation of all equipment.

3.2.2. Vendor shall provide user level training at time of installation for five (5) NSW personnel. At a minimum, training shall include:

3.2.2.1. Initial Setup

3.2.2.2. Replacement/replenishment of additive material

3.2.2.3. Preventive maintenance checks and services

3.2.2.4. Basic and advanced printer operations

3.2.3. Vendor shall provide a one year extended warranty beyond manufacturer warranty that includes:

3.2.3.1. On-site support delivered within three business days. This service shall be performed during regular business hours and include all labor costs, cost of minor replacement parts associated with periodic maintenance, and travel expenses

3.2.3.2. Unlimited technical support during regular working hours

3.2.3.3. Software and hardware update

3.3. Support Material Removal System

3.3.1. Vendor shall provide equipment to remove support structure after printing completion

3.3.2. Water Jet 110V-120V 60Hz OBJ-03006

3.3.2.1. Drain Standard sink drain pipe—40 mm (1.5 inches)

3.3.2.2. Nozzle types • high-pressure jet, for removing stubborn material • fine-spray nozzle, for delicate items

3.3.2.3. Operating method - Air operated foot switch

3.3.2.4. Internal low-energy light Support-waste collector

3.3.3. Water Pressure Pump

3.3.3.1. Water intake - Standard water tap with hose connection.

3.3.3.2. Operating pressure 60 bar (870 psi)

3.3.3.3. Maximum pressure 120 bar (1740 psi)

3.3.3.4. Minimum intake

3.3.3.5. water pressure - 1 atm

3.3.3.6. Maximum intake water temperature 60 °C (140 °F)

3.3.3.7. Water consumption 10 liters/min. at 2800 RPM

3.3.3.8. Noise level 8572 dB (with acoustic protection)

3.3.4. Water Jet & Water Pressure Pump

3.3.4.1. Electrical rating - 110–120 volt, 60 Hz, 18 A (Peak inrush 19.9 A)

3.3.4.2. Power - Input 2.5 kW Output 1.65 kW

3.3.5. Support Material Removal System Technical Specifications:

3.3.5.1. 110–120 VAC 50/60 Hz, 2.3 Amps, CC 5 Amp

3.3.5.2. Drain - 3/4 inch drain hose

3.3.5.3. Water consumption - Output: 64 liters (17 gallons) per minute

3.3.5.4. Circulation: 167% per minute

3.3.5.5. Water operating temperature - 30°C (86°F)

3.3.5.6. Ambient temperature - 20°C–23°C (68°F–73°F)

3.3.5.7. Humidity - 30%–80% (optimum: 55%)

3.3.5.8. Pollution degree - 2

3.4. Consumables: Vendor shall provide consumables to support 3D printing operations in the following quantities:

FullCure 705 Resin

FullCure 835 VeroWhitePlus

FullCure 980 TangoBlackPlus

FullCure 810 VeroClear

OBJET Endur RGD450

SUP706

RDG843 VeroCyan

Objet RGD851 VeroMagenta

Objet RGD836 VeroYellow

4. DELIVERY INFORMATION

4.1. Delivery POC Name: LT Dave Madden

4.2. Delivery address: 2024 Trident Way San Diego, CA 92155 BLDG 603 Rm 184

4.3. Special instructions: N/A

5. QUALITY ASSURANCE: The Government reserves the right to perform inspections and surveillance to evaluate the Contractor’s compliance to the contract terms to include proper delivery of quantity and type of goods. The Government will make every effort to ensure that the surveillance methods used are conducted in an objective, fair, and consistent manner.

Ver: May 2016

Ver: Jan 2015