AHL104-App D - Modular Cabinets (REV1).pdf

APPENDIX D

FOR

MODULAR CABINETS

AT

HOLLOMAN AIR FORCE BASE, NEW MEXICO

BUILDINGS 35 and 283

CSN: NCH805

DATE: 26 MAY 2022

REVISION 1: 18 JULY 2022

PREPARED BY:

James F. Rowland

JAMES F. ROWLAND

PROJECT ENGINEER

AFLCMC/EZPAE

Brad Thompson

BRAD THOMPSON

REVIEWER

AFLCMC/EZPAE

FA8604-22-R-B012 Attachment 5, Rev 1 Page 1 of 13

Holloman AFB, NM – App D – Page ii

Table of Contents

1. SCOPE

2. APPLICABLE DOCUMENTS

3. REQUIREMENTS

3.1. SYSTEM DESCRIPTION

3.2. CHARACTERISTICS

3.2.1. MODULAR CABINETS

3.2.1.1. MODULAR CABINET

3.2.1.2. CABINET HOUSING LOAD CAPACITY

3.2.1.3. PALLET BASE

3.2.1.4. BASE ENCLOSURE

3.2.1.5. DRAWERS

3.2.1.5.1. DRAWER LOAD CAPACITY

3.2.1.5.2. DRAWER DIMENSIONS

3.2.1.5.3. DRAWER PUSH-PULL FORCES

3.2.1.5.4. DRAWER DIVIDER STRIPS

3.2.1.5.5. PARTITIONS

3.2.1.5.6. CROSSWISE DIVIDERS

3.2.1.5.7. DRAWER PULL LABEL HOLDING SYSTEM

3.2.1.5.8. DRAWER STOPS

3.2.1.5.9. CARRIAGES AND BRACKETS

3.2.1.6. DRAWER CONFIGURATION

3.2.1.7. CABINET LOCK

3.2.1.8. ASSEMBLY

3.2.1.9. ALIGNMENT

3.2.1.9.1. STORAGE UNIT VERTICAL ALIGNMENT

3.2.2. HARDWOOD TOP (REV1)

3.2.3. TOP CABINET

4. QUALITY CONFORMANCE

4.1. INSPECTIONS

4.2. TESTS

4.3. CERTIFICATIONS

FA8604-22-R-B012 Attachment 5, Rev 1 Page 2 of 13

Holloman AFB, NM – App D - Page 1

1. SCOPE

This appendix establishes the minimum performance, design, fabrication, installation, and test requirements for modular cabinets for Buildings 35 and 283 at Holloman Air Force Base, New Mexico. The work shall be completed in accordance with this appendix, the Cover Purchase Description (PD), and Air Force (AF) Drawings AHL104-01 and -02. This appendix covers all equipment, materials, and labor necessary to complete installation of the system.

2. APPLICABLE DOCUMENTS

Applicable documents shall be in accordance with Section 2 of the Cover PD.

3. REQUIREMENTS

3.1. SYSTEM DESCRIPTION

The modular cabinet system a will be used to store small sized items in such a manner as to permit placement and removal of any individual item.

3.2. CHARACTERISTICS

3.2.1. MODULAR CABINETS

A modular cabinet is defined as a unitary set of drawers/shelves and the housing or cabinet used to support the drawers/shelves.

Individual drawers shall be compartmentalized to provide separation between different parts. The modular cabinet storage systems shall be located and configured as shown on AF Drawings AHL104-01 and -02. The system shall be modular in construction for easy dismantling and re-assembly.

3.2.1.1. MODULAR CABINET

Three cabinet configuration types shall be provided, two as shown on AF Drawing AHL104-01 and one as shown on AF Drawing AHL104-02. Each cabinet shall have outside dimensions as specified in Table 1.

FA8604-22-R-B012 Attachment 5, Rev 1 Page 3 of 13

Holloman AFB, NM – App D - Page 2

Table 1. Outside Cabinet Dimensions

Cabinet Configuration

Type

Quantity Width (inches)

Depth (inches)

Height (inches)

M1 8 29 +/- 1¼ 28 +/- ½ 37 +/- 1¼ M2 2 29 +/- 1¼ 28 +/- ½ 59 +/- 1¼ M3 78 48 +/- 1¼ 28 +/- ½ 59 +/- 1¼

The modular cabinet shall have drawers configured as specified in Table 2.

3.2.1.2. CABINET HOUSING LOAD CAPACITY

Each cabinet housing shall be capable of supporting a minimum static load of 10,000 pounds.

3.2.1.3. PALLET BASE

Each modular cabinet shall be provided with a built-in pallet base. The pallet base shall be an integral part of the modular cabinet. The pallet base shall have a height of 2.5 +/- 0.5 inches.

3.2.1.4. BASE ENCLOSURE

Each modular cabinet shall have removable base enclosure plates to cover the front and rear of the pallet base.

3.2.1.5. DRAWERS

3.2.1.5.1. DRAWER LOAD CAPACITY

Each drawer shall have a minimum capacity of 400 pounds. When fully loaded with 400 pounds, all drawers shall be capable of being opened and closed without jamming or twisting of the carriage. When fully loaded, an open drawer shall not exhibit deflection greater than 0.62 inch from its closed position, when measured from the floor to the middle of the front of the drawer.

3.2.1.5.2. DRAWER DIMENSIONS

The inside drawer dimensions shall be 25 inches +/- 1 inch for both width and depth for Types “M1” and “M2”. The inside drawer

FA8604-22-R-B012 Attachment 5, Rev 1 Page 4 of 13

Holloman AFB, NM – App D - Page 3 dimensions shall be 25 inches +/- 1 inch for both depth and 48 inches +/- 1 inch for Type “M3”. The height of the sides and back wall of the drawer shall not be less than 48 percent of the drawer front height.

3.2.1.5.3. DRAWER PUSH-PULL FORCES

The forces required to move a drawer, loaded to the maximum capacity of 400 pounds per drawer, shall not exceed 25 pounds to start outward, 45 pounds to start inward, and 40 pounds to continue moving.

3.2.1.5.4. DRAWER DIVIDER STRIPS

Divider strips shall be provided around the four inside walls of each drawer. The divider strips shall be factory installed, and an integral part of the drawer. The divider strips shall provide for spacing of partitions and crosswise dividers in a range of 0.50 inch to 1 inch intervals.

3.2.1.5.5. PARTITIONS

Partitions shall be defined as drawer dividers which run from front-to-back of each drawer. All partitions shall be made of steel. Partitions shall have slot spacing to match the drawer divider strips for placement of crosswise dividers. Each partition shall be anchored with a minimum of two bolts and nuts or two self-tapping metal screws to the bottom of the drawer to keep the partition flush against the bottom of the drawer. The height of the partitions and crosswise dividers shall be no less than 75% of the height of the drawer body. All partitions shall be installed across the depth of each drawer.

3.2.1.5.6. CROSSWISE DIVIDERS

Crosswise dividers shall be defined as dividers placed between adjacent partitions or between a drawer divider strip and a partition. All crosswise dividers shall be made of steel or aluminum. Crosswise dividers shall be easily removable and interchangeable with other crosswise dividers of the same size.

All crosswise dividers shall be installed across the width of each compartment.

3.2.1.5.7. DRAWER PULL LABEL HOLDING SYSTEM

Each drawer pull shall be aluminum and shall have a label holding system. The label holding system shall be at least 20 inches long and shall be designed to accept a label at least one

FA8604-22-R-B012 Attachment 5, Rev 1 Page 5 of 13

Holloman AFB, NM – App D - Page 4 inch high. The label holding system shall have a clear plastic shield covering a paper label with plastic or aluminum end caps that provide an enclosed label system. The contractor shall provide two spare label end caps per cabinet. There shall be no sharp protrusions on any part of the drawer pull label holding system.

3.2.1.5.8. DRAWER STOPS

Each drawer shall be equipped with drawer stops to prevent over-travel of the drawer when fully extended. These safety stops shall prevent the drawer from being removed unless released by the operator.

3.2.1.5.9. CARRIAGES AND BRACKETS

The cabinets shall include carriages (defined as rolling intermediate members which permit 100 percent extension of the drawer interior) and minimum 10 gauge steel brackets or side channels (defined as those members fixed to the sides of the cabinets). Carriages shall operate on precision ball and/or roller bearings. All carriages and brackets shall be the same for all drawers and completely interchangeable to preclude any possibility of an unsafe mix-up of lightweight brackets and carriages with heavily loaded drawers.

3.2.1.6. DRAWER CONFIGURATION

The modular cabinet configuration shall be as indicated in Table

1. Each drawer shall be compartmentalized such that the assigned numbers of compartments are provided as shown in Table

2. The compartments within a single drawer shall be approximately equal in size.

TABLE 2 - MODULAR CABINET CONFIGURATION

Number of Drawers

Usable Height

(inches)

Number of Compartments Across Width

Number of Compartments Across Depth

Modular Cabinet Configuration “M1” – Quantity 8 4 3-7/8” 4 5 2 5-3/8” 4 4

Modular Cabinet Configuration “M2” – Quantity 2 6 3-7/8” 4 5 4 5-3/8” 4 4

FA8604-22-R-B012 Attachment 5, Rev 1 Page 6 of 13

Holloman AFB, NM – App D - Page 5

Modular Cabinet Configuration “M3” – Quantity 78 4 7” 4 4 1 20” 4 4

3.2.1.7. CABINET LOCK

Each cabinet of the modular cabinet system shall have a keyed lock. The lock shall prevent unauthorized entry into a cabinet drawer. Each modular storage cabinet system shall have a minimum of five keys/building. All locks shall be keyed alike.

3.2.1.8. ASSEMBLY

The Contractor shall assemble all cabinets including: leveling cabinets, installing base enclosures, installing drawers in cabinets, installing compartmentalization (partitions and crosswise dividers), and installing shelves.

3.2.1.9. ALIGNMENT

After assembly, the storage units shall be capable of maintaining the same position in all loaded conditions.

Alignment of each row of storage units shall be in two directions: down the row of storage units, maintaining the proper aisle width between adjacent rows of storage units; and vertically for each drawer/shelf cabinet face.

3.2.1.9.1. STORAGE UNIT VERTICAL ALIGNMENT

Each storage unit face shall be plumb to within 0.12 inch from the floor to the top of the unit.

3.2.2. HARDWOOD TOP (REV1)

The eight “M1” modular cabinets shown on AF Drawing AHL104-01 shall be arranged to form a combined work counter. A singular butcher-block hardwood top approximately 56 52”W x 120”L shall be mounted on top of these cabinets to form a continuous work surface.

3.2.3. TOP CABINET

The 78 “M3” modular cabinets shown on AF Drawing AHL104-02 shall have a 24 inch high top cabinet attached to them to make a combined 83 inch high unit. Each top cabinet shall have one shelf dividing the space into equal parts.

FA8604-22-R-B012 Attachment 5, Rev 1 Page 7 of 13

Holloman AFB, NM – App D - Page 6

4. QUALITY CONFORMANCE

4.1. INSPECTIONS

The system shall be inspected to verify that it meets all the requirements of sections 1, 2, and 3 of this appendix and the Cover Purchase Description. These inspections shall be completed as part of the system checkout test and again as a part of the quality conformance test.

4.2. TESTS

The following tests shall be performed on the system as part of the system checkout test and again as a part of the quality conformance test.

No. Paragraph Description

1. 3.2.1.5.1. A minimum of five cabinet drawers picked at random shall be loaded with 400 pounds. While the drawer is closed, the height to the top of the drawer from the floor shall be measured and recorded. The loaded drawer shall be opened and left for a minimum of four continuous hours. The height of the top of the drawer front shall be recorded while the drawer is fully open. If an open drawer sags more than 0.62-inch when compared to its closed position, the system shall fail the test.

2. 3.2.1.5.3. A minimum of five cabinet drawers picked at random shall be loaded with 400 pounds. This test may be conducted in conjunction with test number one. The amount of force to pull and push the loaded drawer shall be measured with a digital force gauge. If the drawer requires more than 25 pounds to start outward the system shall fail the test. If the drawer requires more than 45 pounds to start inward or more than 40 pounds to continue moving inward, the system shall fail the test.

FA8604-22-R-B012 Attachment 5, Rev 1 Page 8 of 13

Holloman AFB, NM – App D - Page 7

3. 3.2.1.5.9. Ensure that all drawer interior compartments extend 100 percent out of the housing exposing all contents to reach and visibility. If the drawers do not allow for 100 percent extension, the system shall fail the test.

4.3. CERTIFICATIONS

The Contractor shall provide certification that the following requirements have been met in accordance with the Contract Data Requirements List.

No. Paragraph Certifications

1. 3.2.1.2. Cabinet housings have a minimum static load capacity of 10,000 pounds.

FA8604-22-R-B012 Attachment 5, Rev 1 Page 9 of 13

Holloman AFB, NM – App D - Modular Cabinet TPQ - Page 1 of 4

TECHNICAL PROPOSAL QUESTIONNAIRE

FOR

MODULAR CABINET MINI-MEZZANINE

Solicitation Number: FA8640- -R- Project Title: Storage Aid System Base: Holloman AFB, NM CSN: AHL104 Appendix D, Modular Cabinets, 26 May 2022

This questionnaire shall be completed by the Offeror. All entries to this questionnaire shall be typed. The questionnaire will be used to determine the Offeror's understanding of the requirements and acceptability of the proposed equipment.

Please attach product literature/cut sheets for all equipment detailed in this questionnaire and attach any exceptions to the Purchase Description Appendix as detailed below.

Modular Cabinet Manufacturer: _____________________________ Modular Cabinet Model Number: _____________________________

No. Paragraph Characteristic

1. 3.2.1.1.

Quantity of modular cabinets provided: ________

Cabinet configuration dimensions:

Type “M1” Width: _________ inches Depth: _________ inches Height: _________ inches dimensions:

Type “M2” Width: _________ inches dimensions:

Type “M3” Width: _________ inches

2.

3.2.1.2. Cabinet housing vertical static load capacity:

________ pounds

FA8604-22-R-B012 Attachment 5, Rev 1 Page 10 of 13

Solicitation Number: FA8604- -R-

Holloman AFB, NM – App D - Modular Cabinet TPQ - Page 2 of 4

3. 3.2.1.3. Is a pallet base provided?

YES NO

4. 3.2.1.3. Height of pallet base: _______ inches

5. 3.2.1.4. Are base enclosure plates provided to cover the front and rear of the pallet base?

6. 3.2.1.5.1. Maximum drawer load capacity: _______ pounds

7. 3.2.1.5.2. Inside drawer dimensions:

Width: _________ inches

8. 3.2.1.5.2. Is the height of the sides and back wall of the drawer greater than 48 percent of the drawer front height? YES NO

9. 3.2.1.5.3. Force to move a fully-loaded drawer outward:

______ pounds Force to move a fully-loader drawer inward:

______ pounds

10. 3.2.1.5.4.

3.2.1.5.5.

3.2.1.5.6.

Are drawer divider strips, metal partitions, and crosswise dividers provided as specified?

11. 3.2.1.5.7. Does each drawer front have an aluminum drawer pull label holding system?

12. 3.2.1.5.8. Is each drawer equipped with drawer stops to prevent over-travel of the drawer?

13. 3.2.1.5.9. Do drawer interior compartments extend 100 percent out of the housing to expose all contents?

14. 3.2.1.5.9. Do the drawer carriages operate on precision ball and or roller bearings?

FA8604-22-R-B012 Attachment 5, Rev 1 Page 11 of 13

Holloman AFB, NM – App D - Modular Cabinet TPQ - Page 3 of 4

15. 3.2.1.6. Provide the drawer configuration for modular cabinets:

Cabinet Configuration Type

# of Drawers

Usable Height

Number of compartments

M1:

M2:

M3:

16. 3.2.2 Will a hardwood top be provided for Type “M1” cabinets as specified?

YES NO

17. 3.2.3 Will top cabinets be provided for Type “M3” cabinets as specified?

FA8604-22-R-B012 Attachment 5, Rev 1 Page 12 of 13

Holloman AFB, NM – App D - Modular Cabinet TPQ - Page 4 of 4

EXCEPTIONS

Attach any exceptions taken to the Purchase Description.

Outline those concerns in detail. Your exceptions will be reviewed to determine acceptability.

Are exceptions taken? YES NO

Number of pages attached: ____________________________________

FA8604-22-R-B012 Attachment 5, Rev 1 Page 13 of 13