9626025_98752_Rev_F.pdf

APPLICATION REVISIONS

NEXT ASSY USED ON LTR DESCRIPTION DATE APPROVED

B REVISED PER ECO 98A0002 2003-03-17 BY

C REVISED PER ECO 98A0003 2006-07-14 BY

D REVISED PER ECO 2008A0004 2008-02-04 BY

E REVISED PER ECO 2010A0005 2010-02-12 BY

F REVISED PER ECO 2013A0006 2013-08-27 GG

REV

SHEET

REV

SHEET

REV STATUS

OF SHEETS

REV F F F F F F F F F

SHEET 1 2 3 4 5 6 7 8 9

Distribution Statement A. Approved for public release; distribution is unlimited.

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES

TOLERANCES ON

FRACTIONS DECIMALS ANGLES

± .XX ± ±

.XXX ±

U.S. AIR FORCE

ROBINS AFB, GA

APPROVALS DATE

DRAFTSMAN

Robert Yohe

TITLE

AIR FORCE DRAWING

REQUIREMENT

CHECKER

J. Westmoreland 96/16/05

MATERIAL ENGINEER

Edwin J. Reid 96/16/05

PROJECT ENGINEER

TREATMENT

None

PROJECT AUTHORITY

Donald R. Looney 96/16/05

SIZE

A

A.F. CODE IDENT NO.

98752

DRAWING NO.

9626025

FINISH

None

RELEASE AUTHORITY

David Olson 05/16/96

SCALE

None

REV F SHEET

ENGINEERING DRAWING LAYOUT A VERTICAL

TABLE OF CONTENTS

PARAGRAPH

1. Scope

2. Air Force Drawing Formats

2.1 Continuation sheets

3. Drawing Form Signature Block

4. Government Activity and Part Identification

4.1 Engineering Order (EO) Number Assignment

4.2 Revision Rules

4.3 Delivery

5. Suffix Identifiers (Formerly Dash Numbers)

5.1 Detailed Suffix Numbers

5.2 Assembly Suffix Numbers

5.3 Shown and Opposite Parts, Assemblies and/or Installations

6. Control Drawings

7. General Notes

7.1 Text Fonts

7.2 Minimum Letter Height

8. Parts List

8.1 Find Numbers

9. Deltas

10. Crowding of Drawings

11. Drawing Entries

CAGE: 98752 DWG. NO.: 9626025 REV F SHEET: 2

12. Distribution Statement, Export Control Notice, and Destruction Notice

13. Saving Air Force Drawings

14. Engineering Drawing Practices

14.1 Prohibited References/Wording

15. Government CAGE Digital Delivery Requirements

15.1. Government CAGE 2D drawings

15.2 Government CAGE 3D Models/Model Based Definition Data Sets

16. Zoning

17. Classified Data Deliveries

CAGE: 98752 DWG. NO.: 9626025 REV F SHEET: 3

1. Scope: The purpose of this document is to define format requirements for the generation of Air Force drawings. The language contained herein applies if a contractor or WR-ALC organically is tasked with preparing Air Force (Government) CAGE coded drawing(s).

2. Air Force Drawing Formats: Contact the Engineering Data Management Specialist (EDMS) to acquire the following digital forms.

AF Form Number, Title and Size (in inches):

AF Form 1651, Engineering Drawing Layout – A Horizontal (11 x 8-1/2) AF Form 1652, Engineering Drawing Layout – A Vertical (8-1/2 x 11) AF Form 1652A, Engineering Drawing Layout – A Vertical (Continuation sheet) (8-1/2 x 11) AF Form 1653, Engineering Drawing Layout – B (11 x 17) AF Form 1654, Engineering Drawing Layout – C (17 x 22) AF Form 1655, Engineering Drawing Layout – D (22 x 34) AF Form 1656, Engineering Drawing Layout – E (34 x 44) AF Form 1658, Parts List (8-1/2 x 11) AF Form 1659, Data List (8-1/2 x 11) AF Form 1660, Index List (8-1/2 x 11) AF Form 1661, Tube Bend Drawing (8-1/2 x 11) AF Form 2602, Engineering Document Release Record (8-1/2 x 11) AF Form 3925, Engineering Order (11 x 8-1/2, hor.) (Formerly AF Form 2600) AF Form 3926, Engineering Order (Continuation Sheet) (11 x 8-1/2, hor.)

(Formerly AF Form 2601) AF Form 3927, Engineering Order (Parts List) (11 x 8-1/2, hor.) (Formerly AF Form 2601)

NOTE: Larger drawing sizes may be generated in accordance with ASME Y14.1.

2.1 Continuation sheets: When AF Forms 1653 through 1656, and larger drawing formats sizes as defined in ASME Y14.1, are used to prepare multi-sheet drawings, and the forms are generated in a CAD system, the minimum title block described in ASME Y14.1, may be used for continuation sheets. All other features of the AF drawing forms, such as border, border sectioning, revision blocks, etc. are included. Identification as a continuation sheet is indicated by adding “(Continuation Sheet)” following the form name centered in the lower margin (i.e.

ENGINEERING DRAWING LAYOUT D (Continuation Sheet).

3. Drawing Form Signature Block: If a contractor activity is creating the drawing, the technician (Tech) and Checker (CHK) blocks shall have the contractor’s employee’s names and dates inserted. If a government activity is doing the drawing, the Technician and Checker block shall have AF employee’s names and dates inserted. The other four blocks will always have AF employee’s names and dates. The “Air Force Authentication” block shall have the Engineers supervisor’s name and date inserted. Names shall be printed on the drawing form in the appropriate blocks.

Contact the requiring office in block 6 of the DD Form 1423 or Engineering Data Management Specialist (EDMS), for the Government names to put in the appropriate signature blocks.

The drawing number located in the title block of sheet 1 shall be prefixed with an “X”. The "X" is removed by the draftsman after Air Force Release approval has been granted by the Engineering Data Management Specialist (EDMS). Note: For this document Air Force Release

CAGE: 98752 DWG. NO.: 9626025 REV F SHEET: 4

and EDMS are synonymous. On drawing forms, in the approval area, there shall be six blocks for names, as follows:

Tech (Contractor/Government) CHK (Contractor/Government) ENG (Government System Engineer) CRSN (Corrosion) As Applicable AIR FORCE AUTHENTICATION (Government Project Engineer’s Supervisor) AIR FORCE RELEASE (Government Designated Activity)

4. Government Activity and Part Identification: The contractor shall use the Government activity identifier Commercial and Government Entity (CAGE) code and Air Force drawing numbers. The contractor shall contact the EDMS to obtain the drawing numbers.

4.1 Engineering Order (EO) Number Assignment: Contact the EDMS to acquire the EO number. All EO’s shall be incorporated into the Government drawing prior to the paper submittal for review and final submittal. The Government approved EO shall be delivered in TIFF or PDF format with the final delivery, as well as the revised Government drawing. Blocks 12 & 13 of the EO shall contain actual signatures prior to scanning.

4.2 Revision Rules: When multiple sheet drawings are in book form, all sheets may be identified by the same revision letter without regard to the specific sheet(s) to which the revision applies. Otherwise sheet one (1) always carries the highest revision which reflects the revision status of the group as a whole.

4.3 Delivery: New developed Government CAGE drawings shall be at basic revision upon final release. See the latest revision of Air Force (CAGE 98752) drawing 9579776 for content, format, and media requirements for delivery of Digital Engineering Data.

5. Suffix Identifiers (Formerly Dash Numbers): The suffix identifier is a numerical identification, appended to a drawing number to identify individual parts, assemblies or drawing types. All parts depicted on Air Force drawings will be identified with the appropriate suffix identifier as shown in the following paragraphs.

5.1 Detailed Suffix Identifiers: Use odd suffix identifiers on all defined detail items. Use even numbers for the opposite or mirror-image items. Do not use suffix identifiers ending in "9" or "0".

Parts Shown Opposite

-01 -02

-03 -04 -05 -06 -07 -08 (Do Not Use Suffix Identifiers Ending in 9 or 0) -11 -12 -13 -14 -15 -16

CAGE: 98752 DWG. NO.: 9626025 REV F SHEET: 5

5.2 Assembly Suffix Identifiers: Use suffix identifiers beginning with an odd number and ending with "0" for all defined assemblies. Use suffix identifiers beginning with an even number and ending with "0" for the opposite or mirror-image assemblies.

Assemblies

Shown Opposite -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 -140

5.3 Shown and Opposite Parts, Assemblies and/or Installations: When using SHOWN AND OPPOSITE PARTS, and ASSEMBLIES AND/OR INSTALLATIONS, identify them as such in the PARTS LIST.

-01 (shown) -02 (opposite) -10 Assy (shown) -20 Assy (opposite) -10 Instl (shown) -20 Instl (opposite)

6. Control Drawings: Prepare control drawings for commercial or vendor items in accordance with ASME Y14.24.

7. General Notes: The General Notes area of the drawing shall be identified with the heading "NOTES". General Notes are located on sheet one (1) and continue on subsequent sheets as necessary. General Notes are located in the upper left hand corner for drawing sizes “B” “C” “D” “E” and "J". The General Notes column shall be positioned .50 to 1.00 inch down from the top border and .50 to 1.00 inch in from the side border. The General Notes column shall not exceed 8 inches in the horizontal direction.

All general notes shall be top to bottom in numerical sequence beginning with one (1).

7.1 Text Fonts: The standard font set that is basic to the CAD system shall be used.

7.2 Minimum Letter Height: Minimum letter heights per ASME Y14.2 shall be used.

8. Parts List: It is preferred that the Parts List shall be located on sheet one (1) and continued for as many sheets as necessary. When the Parts List extends into the General Notes area on sheet one (1) and any subsequent sheets, the General Notes must be indexed on the first sheet or subsequent sheets as to their location or their continuation (Parts List takes precedence over Notes). Parts List entry spaces shall be .50 inch high. When additional space is required, the height of the entry spaces shall be increased in increments of .50 inch. Each row shall be filled

in. Blank rows shall be annotated “NOT USED”, “LEFT BLANK INTENTIONALLY”, etc. in the row or by being flagged and annotated in the notes within the field of the drawing.

CAGE: 98752 DWG. NO.: 9626025 REV F SHEET: 6

8.1 Find Numbers: Within the Parts List all find numbers shall be identified with whole consecutive numbers beginning with one (1). Find Numbers within the field of the drawing shall be enclosed in a .50 inch diameter circle.

9. Deltas (Flagnote Symbols): The height of all deltas shall be .50 inch to flag notes. The applicable general note number appears within the flag note symbol. (Circles shall not be used to flag notes).

10. Crowding of Drawings: AF drawings shall be drawn to allow room for growth, and/or changes/revisions. The contractor shall leave a minimum of three inches of blank space below the revision block to allow room for growth. Notes and Parts List shall also allow room for growth.

11. Drawing Entries: Entries on drawings shall be individual entries. Sub-Routines are not permitted.

12. Distribution Statement, Export Control Notice, and Destruction Notice: The instructions for Distribution Statement, Export Control Notice, and Destruction Notice listed in CDRL DD Form 1423 Technical Data Package (TDP) shall apply. When a DD Form 1423 for TDP's does not exist, the Engineering Data Management Specialist (EDMS) shall be contacted for proper markings.

13. Saving Air Force Drawings: The file naming convention shall be the drawing number indicated on the drawing in its entirety, without the X prefix (as mentioned in paragraph 3), including any applicable unique prefix identifier, such as PL (when applicable), then followed by the sheet number beginning with one (1) and continuing for additional sheets using consecutive whole integers, then by any applicable revision letter all separated by an underscore character.

The file extension is then added on last, such as .dwg for native AutoCAD files. Include the unique suffix identifier (formerly called the dash number), only if it is actually part of the drawing number. For raster files (such as .tif) that are delivered in frames, the frame number shall be indicated by the letter “F” and the applicable frame number beginning with one (1) and continuing for additional frames using consecutive whole integers. This shall be inserted between the sheet number and the revision letter using an underscore character before and afterwards. There shall be no more than one underscore character in the filename consecutively.

Drawing No. Save As

9032521 9032521.dwg for single 1 sheet drawing

9032521 9032521_1.dwg for 9 sheet drawing thru 9032521_9.dwg

9032521 9032521_01.dwg for 99 sheet drawing

9032521_99.dwg

9032521 9032521_001.dwg for 999 sheet drawing

CAGE: 98752 DWG. NO.: 9626025 REV F SHEET: 7

9032521-10

9032521_999.dwg

9032521-10_1.dwg for unique suffix identifier

9032521

9032521_1_F1_A.tif for TIFF raster files with frames

9032521

9032521.pdf for PDF files with multiple sheets

14. Engineering Drawing Practices: The ASME Y14.100 standard for engineering drawing practices shall apply.

14.1 Prohibited References/Wording: Technical Orders (TOs), pamphlets, recordings, National Stock Numbers (NSNs), To Be Determined (TBD), Statement of Work (SOW), Performance Work Statement (PWS), Statement of Objectives (SOO), and Contract Data Requirements List (CDRL), shall not be referenced on engineering drawings.

15. Government CAGE Digital Delivery Requirements: The following describes the format required for Air Force CAGE coded 2D drawings and 3D models. A note shall be added to Air Force drawings referencing any models that are used with that drawing. Models created along with Air Force drawings shall have the native drawings in a zipped format along with the models to preserve the links. The view-only and neutral model files shall be delivered in separate files.

The final digital delivery shall also comply with the latest revision of Air Force (CAGE 98752) drawing 9579776.

15.1 Government CAGE 2D Drawings: All entities shall be present on layer zero and in model space. The drawings shall not contain a mix of vector and raster images, nor have any texts or other objects grouped together by using grouping commands. When the native CAD software used for producing government CAGE 2D drawings is not AutoCAD, the contractor shall deliver translated or exported AutoCAD (*.DWG) files. The contractor is responsible of verifying the translation to DWG is accurate. All translated and exported DWG files must be able to be manipulated using standard AutoCAD drafting procedures. The contractor shall provide drawings in accordance with the following: Native AutoCAD (*.DWG), View Only Hewlett Packard Graphics Language (HPGL) (*.PLT), and Searchable PDF drawings (*.PDF).

AND

15.2 Government CAGE 3D Models / Model-Based Definition Data Sets: Model-Based Definition deliveries shall comply with ASME Y14.41. When Government CAGE 3D Models / Model-Based Definition Data Sets are developed, 3D models shall be delivered in the following formats:

CAGE: 98752 DWG. NO.: 9626025 REV F SHEET: 8

Native - Any format native to the contractor's CAD system is acceptable (e.g. Autodesk Inventor (preferred) (*.IAM assembly and *.IPT part), CATIA, Intergraph, Applicon, Unigraphics, etc.)

Neutral - Product Data Exchange using STEP (PDES) data per ISO 10303 Application Protocols AP 203 (preferred) or AP 214. The contractor is responsible for verifying the native translation to neutral is accurate.

Viewable - Viewable tessellated model files suitable for use with a 3rd party viewer (e.g.

JT format (preferred), Virtual Reality Model Language (VRML), 3D PDF, etc.)

16. Zoning: Zoning references shall be used except on “A” or “A4” size drawings and shall be reflected in the revision block.

17. Classified Data Deliveries: The EDMS shall be notified prior to any classified digital data delivery. Classified markings for the digital data media and documentation shall be in accordance with DOD 5220.22-M. Classified and unclassified data shall NOT be intermingled in a shipment, but instead they shall be packaged and shipped separately. Contract requirements for protection of classified data shall apply.

CAGE: 98752 DWG. NO.: 9626025 REV F SHEET: 9