1273126_EI_Attach_A.pdf

REV: ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

WHEEL ASSEMBLY NOSE (F-16)

2. PART NUMBER:

201128014-10

3. NATIONAL STOCK NUMBER:

1630-01-606-0371 LE

4.0 THE FOLLOWING SPECIFICATIONS/STANDARDS, ETC., WILL BE USED IN LIEU OF THE DATA INDICATED. THE

SUPERSEDED DATA WILL NOT BE FURNISHED UNLESS SO INDICATED.

5.0 MATERIAL REVIEW BOARD DISPOSITION:

A) OO-ALC LANDING GEAR ENGINEERING RETAINS ALL RIGHTS TO REVIEW AND ACCEPT MATERIAL REVIEW

BOARD (MRB’S) DISPOSITIONS PRIOR TO SHIPMENT OF DISCREPANT ITEM. ALL DEVIATIONS, MINOR (CLASS II) AND MAJOR (CLASS I), FROM THE ENGINEERING DRAWING PACKAGE SHALL BE SUBMITTED FOR MRB

DISPOSITION.

B) PRIOR TO CONTRACT AWARD, THE CONTRACTOR SHALL CERTIFY TO THE GOVERNMENT IN WRITING FULL

COMPLIANCE WITH MANUALS, SPECIFICATIONS, AND STANDARDS CALLED OUT AND REQUIRED FOR THE MANUFACTURE OF THIS CONTRACTED LANDING GEAR COMPONENT/ASSEMBLY. CONTRACTOR IS RESPONSIBLE TO COMPLETELY SEARCH THESE MANUAL, SPECIFICATIONS, AND STANDARDS AND FULLY UNDERSTAND THE REQUIREMENTS NECESSARY TO MANUFACTURE LANDING GEAR COMPONENTS. ANY QUESTIONS CAN BE

FORWARDED TO OO-ALC LANDING GEAR ENGINEERING.

6.0 DRAWING 201128014 – WHEEL ASSEMBLY NOSE

6.1 THE FORGING SHALL BE PROCURED FROM SOURCES APPROVED BY LANDING GEARN ENGINEERING USING THE

ORIGINAL CERTIFIED FORGING PROCEDURES AND DIES/TOOLING.

A. THE CONTRACTOR MAY PROCURE FORGINGS FROM SOURCES PRE-APPROVED BY LANDING GEAR

ENGINEERING PER PARAGRAPH B AND C, OR MAY ELECT TO DEVELOP SOURCES PER PARAGRAPH D.

B. IF FORGINGS ARE PROCURED FROM SOURCES APPROVED BY OO-ALC LANDING GEAR ENGINEERING, ORIGINAL CERTIFIED FORGING PROCEDURES AND DIES/TOOLING OR EQUIVALENT (E.G., REFURBISHED/RESUNK BY APPROVED FORGING SOURCE AND HAVING THE SAME DIE NUMBER DESIGNATION) SHALL BE USED. NEW TOOLING AT AN EXISTING SOURCE WILL BE QUALIFIED PER PARAGRAPH C. PRIOR TO CONTRACT AWARD, THE DETAILED PART BIDDER SHALL PROVIDE VERIFICATION (E.G., FORGING QUOTE) TO THE GOVERNMENT THAT THE CERTIFIED DIES AND PROCEDURES ARE AVAILABLE FOR THEIR USE IN THE EVENT THEY ARE THE SUCCESSFUL

BIDDER.

THE FOLLOWING VENDOR HAS PROPRIETARY OWNERSHIP OF AN EXSISTING FORGING DIE:

1. FORGING DRAWING: 201128013

2. DIE #: UNKNOWN

3. LOCATION OF FORGING DIES: PARKER-HANNIFAN CORPORATION AIRCRAFT WHEEL & BRAKE

4. PHONE: UNKNOWN

5. CAGE:33269

C. IF THE FORGING SOURCE IS LISTED AS UNKNOWN OR THE CONTRACTOR WISHES TO DEVELOP ADDITIONAL

SOURCES OR NEW TOOLING AT AN EXISTING FORGING SOURCE, THE CONTRACTOR SHALL ADVISE THE GOVERNMENT IN WRITING OF THEIR INTENT TO PROCURE NEW FORGING DIES AND THE PROPOSED FORGING SOURCE PRIOR TO CONTRACT AWARD. THE CONTRACTOR SHALL NOT PROCEED TO OBTAIN NEW DIES WITHOUT THE EXPRESS CONSENT OF THE GOVERNMENT PROCURING AGENCY (SEE OO-ALC LANDING GEAR ENGINEERING FORGING SQS FOR FURTHER INFORMATION ON FORGING TOOLING QUALIFICATION REQUIREMENTS). THE GOVERNMENT SHALL HAVE UNLIMITED USE OF THE DIES DEVELOPED UNDER THIS CONTRACT. THE CONTRACTOR SHALL INFORM THE FORGING HOUSE IN WRITING, AT THE SAME TIME THE ORDER FOR THE DIES IS

PREPARED BY:

JOHN HUKKA, 2nd Lt.

OFFICE SYMBOL:

417 SCMS/GUEA

DATE:

11 April 2014

HILL AFB FORM 462 Page 1 of 2

REV: ENGINEERING DATA REQUIREMENTS

(ATTACHMENT “A”)

NOTE: MILITARY SPECIFICATIONS / STANDARDS WILL NOT BE FURNISHED IN THE BID SET.

1. THE FOLLOWING INSTRUCTIONS ARE FURNISHED FOR THE MANUFACTURE OF:

WHEEL ASSEMBLY NOSE (F-16)

2. PART NUMBER:

201128014-10

3. NATIONAL STOCK NUMBER:

1630-01-606-0371 LE

PLACED, THAT THE GOVERNMENT HAS UNLIMITED USE RIGHT OF THE DIES AND FORWARD A COPY OF THIS

LETTER TO THE GOVERNMENT CONTRACTING OFFICER.

D. PRIOR TO PRODUCTION, FORGING LOT QUALIFICATION SHALL BE ACCOMPLISHED AS SPECIFIED ON THE FORGING DRAWING AND SAE AMS 4133. THE DETAILED PART CONTRACTOR SHALL ASSURE THAT THIS HAS BEEN ACCOMPLISHED BY THE FORGING SOURCE AND RETAIN IN THEIR RECORDS FOR NO LESS THAN 10 YEARS.

LANDING GEAR ENGINEERING RESERVES THE RIGHT TO REVIEW THIS DOCUMENTATION AS NEEDED.

7.0 DRAWING 9235390: NUT- WHEEL, LANDING GEAR

7.1 INTERPRET DRAWING PER ASME Y14.100 IN LIEU OF MIL-STD-100.

8.0 DRAWING 9235611: BEARING WHEEL, LANDING GEAR

8.1 INTERPRET DRAWING PER ASME Y14.100 IN LIEU OF MIL-STD-100.

PREPARED BY:

JOHN HUKKA, 2nd Lt.

OFFICE SYMBOL:

417 SCMS/GUEA

DATE:

11 April 2014

HILL AFB FORM 462 Page 2 of 2