Atch_5_-_PL_LOE_Jackets.pdf

USAFA/PL LETTER OF EXCEPTION

28 Apr 17

USAFA LETTER OF EXCEPTION

JACKET, IMPROVED, PHYSICAL TRAINING UNIFORM

The following exceptions will apply when CRFD/PD 04-08 is used to manufacture running suit jackets for the United States Air Force Academy cadets.

Paragraph 3.4 Description. Replace the last two sentences with the following paragraph.

The jacket shall be 100% polyester (see Table VII) AF blue shade 1651, fully lined with white 100% polyester mini-mesh. The jacket shall have long raglan-styled sleeves;

collar, two welt pockets, and elastic at the wrists and jacket bottom (see Figure 3). The jacket shall have a full front opening slide fastener and its pockets shall have slide fasteners. The jacket shall have a 4 1/2 inch (+/–1/4 inch) dart at top of sleeve on shoulder. The raglan sleeve shoulder seams shall be trimmed with 1/16 to 1/8” white reflective or Air Force gray shade 1655, filled piping.

Paragraph 3.7.5 Embroidery Description. Replace the entire paragraph with the following paragraph:

An AF PREP Logo will be embroidered on left breast of the jacket. The finished embroidery on left front shall match the standard sample for size, stitch count, and finished appearance. Standard sample may be obtained from the contracting activity.

Attachment #5

FA700018T0039

The logo shall be embroidered in a polyester thread conforming to DoD Heraldic Yarn for Embroidery and Ribbon, Cable # HA White 67101 with a stiff backing. The embroidery backing shall be a pellon cut around and trimmed to 1/2 inch to 1 inch around the design. The logo shall fit in a 3-3/8” high by 2-2/8” wide square. The letters shall be 11/16” in height and approximately 7/16” in width. The circle diameter shall be 2-5/16”.

The font for the “AF PREP” will be Arial bold. The placement point for the logo shall be the bottom center of the logo.

The vertical placement of the logo shall be as in the below chart, which is the distance from the Raglan shoulder seam and collar seam intercept (sew lines) and the bottom center of the logo.

Size Small Medium Large X Large 2X Large 3X Large 4X Large Vertical

Measurement 8 8 ¾ 9 9 ¼ 9 ½ 9 ¾ 10

The horizontal center of the logo shall be the line parallel to the front zipper top stitching line and passing through the Raglan shoulder seam and collar seam intercept (sew lines). All thread ends that are visible on the item shall be trimmed to a length of not more than 1/4 inch.

Horizontal Center line

3.9 Labels. Replace the entire paragraph with the following paragraph:

A combination contractor identification and care shall be place label shall be placed in all garments. The label shall be cloth, cotton, permanent-coated, conforming to Type VI, classes 1, 2, 10, and 14 of Specification DDD-L-20. The label shall show the following information:

Item Description * Contract Number * Contract Date * Size ** Cadet Name SSN Last 4 Squadron Supplier’s Name * Fabric Content * Care Instruction *

* Applicable data to be inserted by the contractor when labels are printed.

** Applicable data to be stamped in by contractor using permanent-type black ink after labels are printed.

A Code 39 bar code label shall also be affixed to the individual garment package. The Code 39 bar code shall be a removable paper ticket of commercial quality with the USAFA 10LRS/LGLC stock number and Code 39 bar code. The paper ticket shall contain a short item description to include size in plain text.

3.13 Patterns. Replace the entire paragraph with the following paragraph

Standard patterns to be used for cutting the contractor’s working patterns shall be furnished by the Government in AccuMark electronic format. The working patterns shall be identical to the Government patterns except that additional notching to facilitate manufacture is permissible. Also minor modifications are permitted where necessary to accommodate manufacturer’s processes, the exception noted in this document and using automatic equipment. These modifications shall not alter the serviceability or appearance requirements. A ½ inch seam allowance shall be used to set sleeves, make pockets, join lining sides, and set sleeve linings. A ¼ inch seam allowance shall be used to make the pocket flaps, set the pocket flaps, make the collar, and set the collar. The seam allowance for the front slide fastener varies depending upon the size of the fastener tape.

Figures and Graphics. Ignore all figures and graphics pertaining to the USAF running suit. The USAF Academy graphics in this letter shall replace the AF graphics.

Custodian: Preparing Activity:

USAF Academy HQ USAFA/PL Colorado Springs CO 80840 USAF Academy, CO 80840-8210

Reviewing Activity:

HQ USAFA/PL

USAF Academy, CO 80840-8210

STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL

INSTRUCTIONS: The purpose of this form is to solicit beneficial comments which will help achieve procurement of suitable products at reasonable cost and minimum delay, or will otherwise enhance use of the document. USAFA contractors, government activities, or manufacturers/vendors who are prospective suppliers of the product are invited to submit comments to the government. Comments submitted on this form do not constitute or imply authorization to waive any portion of the referenced document(s) or to amend contractual requirements. Attach any pertinent data which may be of use in improving this document. If there are additional papers, attach to form and place both in an envelope addressed to Cadet Uniform Flight, 10 LRS/LGRCU, 2348 Sijan Dr., Suite 2B5, USAF Academy, CO 80840-8210.

DOCUMENT IDENTIFIER AND TITLE

NAME OF ORGANIATION AND ADDRESS CONTRACT NUMBER

MATERIAL PROCURED UNDER A

Direct Government Contract

Subcontract

1. HAS ANY PART OF THE DOCUMENT CREATED PROBLEMS OR REQUIRED INTERPRETATION

IN PROCUREMENT?

A. Give paragraph number and wording.

B. Recommendations for correcting deficiencies.

2. COMMENTS ON ANY DOCUMENT REQUIREMENT CONSIDERED TO RIGID

3. IS THE DOCUMENT RESTRICTIVE?

4. REMARKS

SUBMITTED BY(Printed or typed name and address - Optional)

TELEPHONE NO.

DATE