Attachment_4_WD_WY20190038.pdf

"General Decision Number: WY20190038 01/04/2019

Superseded General Decision Number: WY20180038

State: Wyoming

Construction Type: Highway

County: Laramie County in Wyoming.

HIGHWAY CONSTRUCTION PROJECTS

Note: Under Executive Order (EO) 13658, an hourly minimum wage of $10.60 for calendar year 2019 applies to all contracts subject to the Davis-Bacon Act for which the contract is awarded

(and any solicitation was issued) on or after January 1, 2015.

If this contract is covered by the EO, the contractor must pay all workers in any classification listed on this wage determination at least $10.60 per hour (or the applicable wage rate listed on this wage determination, if it is higher) for all hours spent performing on the contract in calendar year 2019. If this contract is covered by the EO and a classification considered necessary for performance of work on the contract does not appear on this wage determination, the contractor must pay workers in that classification at least the wage rate determined through the conformance process set forth in 29 CFR 5.5(a)(1)(ii) (or the EO minimum wage rate, if it is higher than the conformed wage rate). The EO minimum wage rate will be adjusted annually. Please note that this EO applies to the above-mentioned types of contracts entered into by the federal government that are subject to the Davis-Bacon Act itself, but it does not apply

Page 1 of 9beta.SAM.gov

6/20/2019https://beta.sam.gov/wage-determination/WY20190038/0/document to contracts subject only to the Davis-Bacon Related Acts, including those set forth at 29 CFR 5.1(a)(2)-(60). Additional information on contractor requirements and worker protections under the EO is available at www.dol.gov/whd/govcontracts.

Modification Number Publication Date

0 01/04/2019

SUWY2018-001 05/15/2018

Rates Fringes

CARPENTER (Structure)............$ 22.01 1.32

CONCRETE FINISHER................$ 20.10 4.85

ELECTRICIAN

Electrician (Includes

Inside Wireman, Outside-

Lineman, Signal and

Lighting Work)..............$ 45.44 12.76

Equipment Operator

(Electrical Work Only)......$ 22.78 4.62

Ground Man..................$ 25.86 11.22

IRONWORKER.......................$ 26.12 9.41

LABORER

GROUP 1.....................$ 15.89 7.36

GROUP 2.....................$ 18.74 7.36

GROUP 3.....................$ 18.74 7.36

LABORER CLASSIFCATIONS

GROUP 1: Erector & Installer (fences, guardrail & barrier);

Flag persons (traffic control); Form Strippers; General

Page 2 of 9beta.SAM.gov

Laborers, Heater Tender; Material Checker; Pilot Car Driver;

Pick-up Truck Driver; Pre-watering; Presetting & Pre-irrigation (all work); Riprap Man; Tar & Asphalt Pot Tender.

GROUP 2: Asphalt Raker and Tamper; Bin Wall Installer; Chain

Saw Operator (clearing & grubbing); Concrete Saw (all types);

Dump Man; Form Setter (paving); Hand Operated Vibratory

Roller; High Scaler; Jackhammer & Pavement Breaker;

Landscaper, Landscape Laborer; Maintainer (traffic control);

Mortar Man on Stone Riprap; Nozzle Man (air, water, gunite & sandblasting); Pipe Setter (all pipe types); Tamper Operator

(pneumatic, electric, gas & similar)

GROUP 3: Drill Doctor; Form Setter and Mover; Spader: Spilling and/or Caisson Worker; Miner (driller); Machine Man; Timber

Man; Powderman, Blaster, Tender; Wagon Drill, Air-Trac.

(diamond and other drills for blasting powder or grouting).

PAINTER (BRUSH & SPRAY)..........$ 18.74 7.36

POWER EQUIPMENT OPERATOR

GROUP 1.....................$ 19.86 7.36

GROUP 2.....................$ 20.56 7.36

GROUP 3.....................$ 20.80 7.36

POWER EQUIPMENT OPERATOR CLASSIFCATIONS

ALL ELECTRICAL WORK IS EXCLUDED. FOR ELECTRICAL WORK, USE

EQUIPMENT OPERATOR CLASSIFICATION LISTED UNDER ELECTRICAL

CONSTRUCTION

GROUP 1: Air Compressor (all types); Backhoes & Excavators (to

5 CY.); Batch Bin Weighman, Sissorman or Hopper; Broom

Operator (self-propelled); Chip Spreader Operator; Conveyor

Belt Operator; Crusher Oiler; Form Grader Operator; Joint

Machine Operator; Longitudinal Float Operator; Oiler, Utility;

Page 3 of 9beta.SAM.gov

Power Loader (belt & bucket type); Pump Operator; Roller

Operator, self-propelled (Dirt); Skid Steer (all attachments);

Tire Repairman (large construction equip. tires); Tractor

Operator (farm with or w/o power attachments); Tugger (all types).

GROUP 2: Articulated Rock Truck (all capacity); Asphalt Plant

Operator; Backhoe, Excavator & Shovel (6 CY. & larger); Batch

Plant Operator; Bituminous Laydown Machine Operator; Concrete

Batch Plant Operator; Concrete Finish Machine Operator;

Concrete Spreader & Paver Operator; Concrete Multi Blade Span

Saw (Hunt process); Crusher Operator; Dozer Operator (all sizes & power attachments); Draglines, Cranes, Piledriver &

Truck Mounted Cranes (Mfg. Rating: less than 3.5 CY., and /or less than 50 Tons, all attachments); Drilling Machine, Integrated (all types); Front End Loaders (1.5 up to 10 CY.);

Hydro-type Crane (to 50 tons); Mixer Operator, Concrete (over

1yd.); Motor Patrol Operator (all excluding finish); Mulching

Machine Operator; Oiler (crane & shovels); Pavement Breaker;

Hydro-Tamper & similar; Roller Operators, Asphalt (steel & pneumatic); Roto-Milling Machine (under 8 ft. wide); Scraper

Equipment (all types and sizes; Screed Operator; Trenching

Machine Operator.

GROUP 3: Draglines; Cranes; Piledrivers & Truck Mounted Cranes

(Mfg. Rating: 3.5 CY. or larger and/or 50 tons & larger, all attachments); Front End Loaders (over 10 CY.); Heavy Duty

Mechanic; Machine Doctor; Hoist Operator (two or more drums, shafts, or raises); Mixer Operator (dual drum); Motor Patrol

Operator (finish); Roto-Milling Machine (8 ft. & larger).

TRUCK DRIVER

GROUP 1.....................$ 16.60 7.36

GROUP 2.....................$ 17.93 7.36

GROUP 1: ?A? Frame Truck Driver; Coring Machine (self propelled); Dump Truck Driver (to and including 13 CY.); Flat

Rack Material Truck Driver (to 5 tons); Fuel Service Truck

Page 4 of 9beta.SAM.gov

Driver; Gang Truck Driver; Gravel Spreader; Greaseman, Tireman; Serviceman; Oil Distributor Driver (to & including

3,600 gal.); Snow Plow Driver (the CY. rate of the truck);

Transit Mix or Wet Mix Truck Driver; Utility Winch Truck

Driver; Water Truck Driver (to & including 3,600 gal.).

GROUP 2: Dump Truck Driver (14 to 45 CY.); Flat Rack Material

Truck Driver (over 5 tons); Low Boy & Tandem Axle Float

Driver; Multiple Axle Type Truck (semi); Oil Distributor

Driver (over 3,600 gal); Truck Mechanics; Water Truck Driver

(over 3,600 gal.); Winch Trailer Truck Driver.

WELDERS - Receive rate prescribed for craft performing operation to which welding is incidental.

Note: Executive Order (EO) 13706, Establishing Paid Sick Leave for Federal Contractors applies to all contracts subject to the

Davis-Bacon Act for which the contract is awarded (and any solicitation was issued) on or after January 1, 2017. If this contract is covered by the EO, the contractor must provide employees with 1 hour of paid sick leave for every 30 hours they work, up to 56 hours of paid sick leave each year.

Employees must be permitted to use paid sick leave for their own illness, injury or other health-related needs, including preventive care; to assist a family member (or person who is like family to the employee) who is ill, injured, or has other health-related needs, including preventive care; or for reasons resulting from, or to assist a family member (or person who is like family to the employee) who is a victim of, domestic violence, sexual assault, or stalking. Additional information on contractor requirements and worker protections under the EO is available at www.dol.gov/whd/govcontracts.

Unlisted classifications needed for work not included within

Page 5 of 9beta.SAM.gov the scope of the classifications listed may be added after award only as provided in the labor standards contract clauses

(29CFR 5.5 (a) (1) (ii)).

The body of each wage determination lists the classification and wage rates that have been found to be prevailing for the cited type(s) of construction in the area covered by the wage determination. The classifications are listed in alphabetical order of ""identifiers"" that indicate whether the particular rate is a union rate (current union negotiated rate for local), a survey rate (weighted average rate) or a union average rate

(weighted union average rate).

Union Rate Identifiers

A four letter classification abbreviation identifier enclosed in dotted lines beginning with characters other than ""SU"" or

""UAVG"" denotes that the union classification and rate were prevailing for that classification in the survey. Example:

PLUM0198-005 07/01/2014. PLUM is an abbreviation identifier of the union which prevailed in the survey for this classification, which in this example would be Plumbers. 0198 indicates the local union number or district council number where applicable, i.e., Plumbers Local 0198. The next number, 005 in the example, is an internal number used in processing the wage determination. 07/01/2014 is the effective date of the most current negotiated rate, which in this example is July 1, 2014.

Union prevailing wage rates are updated to reflect all rate changes in the collective bargaining agreement (CBA) governing this classification and rate.

Page 6 of 9beta.SAM.gov

Survey Rate Identifiers

Classifications listed under the ""SU"" identifier indicate that no one rate prevailed for this classification in the survey and the published rate is derived by computing a weighted average rate based on all the rates reported in the survey for that classification. As this weighted average rate includes all rates reported in the survey, it may include both union and non-union rates. Example: SULA2012-007 5/13/2014. SU indicates the rates are survey rates based on a weighted average calculation of rates and are not majority rates. LA indicates the State of Louisiana. 2012 is the year of survey on which these classifications and rates are based. The next number, 007 in the example, is an internal number used in producing the wage determination. 5/13/2014 indicates the survey completion date for the classifications and rates under that identifier.

Survey wage rates are not updated and remain in effect until a new survey is conducted.

Union Average Rate Identifiers

Classification(s) listed under the UAVG identifier indicate that no single majority rate prevailed for those classifications; however, 100% of the data reported for the classifications was union data. EXAMPLE: UAVG-OH-0010

08/29/2014. UAVG indicates that the rate is a weighted union average rate. OH indicates the state. The next number, 0010 in the example, is an internal number used in producing the wage determination. 08/29/2014 indicates the survey completion date for the classifications and rates under that identifier.

A UAVG rate will be updated once a year, usually in January of each year, to reflect a weighted average of the current negotiated/CBA rate of the union locals from which the rate is based.

Page 7 of 9beta.SAM.gov

WAGE DETERMINATION APPEALS PROCESS

1.) Has there been an initial decision in the matter? This can be:

* an existing published wage determination

* a survey underlying a wage determination

* a Wage and Hour Division letter setting forth a position on a wage determination matter

* a conformance (additional classification and rate) ruling

On survey related matters, initial contact, including requests for summaries of surveys, should be with the Wage and Hour

Regional Office for the area in which the survey was conducted because those Regional Offices have responsibility for the

Davis-Bacon survey program. If the response from this initial contact is not satisfactory, then the process described in 2.)

and 3.) should be followed.

With regard to any other matter not yet ripe for the formal process described here, initial contact should be with the

Branch of Construction Wage Determinations. Write to:

Branch of Construction Wage Determinations

Wage and Hour Division

U.S. Department of Labor

200 Constitution Avenue, N.W.

Washington, DC 20210

2.) If the answer to the question in 1.) is yes, then an interested party (those affected by the action) can request review and reconsideration from the Wage and Hour Administrator

(See 29 CFR Part 1.8 and 29 CFR Part 7). Write to:

Page 8 of 9beta.SAM.gov

Wage and Hour Administrator

U.S. Department of Labor

200 Constitution Avenue, N.W.

Washington, DC 20210

The request should be accompanied by a full statement of the interested party's position and by any information (wage payment data, project description, area practice material, etc.) that the requestor considers relevant to the issue.

3.) If the decision of the Administrator is not favorable, an interested party may appeal directly to the Administrative

Review Board (formerly the Wage Appeals Board). Write to:

Administrative Review Board

U.S. Department of Labor

200 Constitution Avenue, N.W.

Washington, DC 20210

4.) All decisions by the Administrative Review Board are final.

END OF GENERAL DECISION

Page 9 of 9beta.SAM.gov