MOD Extension to 08-R-0026.doc

SECTION SF 30 BLOCK 14 CONTINUATION PAGE

SUMMARY OF CHANGES

SECTION A - SOLICITATION/CONTRACT FORM

The required response date/time has changed from 04-Aug-2008 03:00 PM to 06-Aug-2008 03:00 PM.

SECTION C - DESCRIPTIONS AND SPECIFICATIONS

The following have been modified:

SALIENT CHARACTERISTICS

SALIENT CHARACTERISTICS

Construction Requirements List (applies to all items)

The Defensor Fortis-Load Carrying System (DF-LCS) shall utilize a weave and snap closure mechanism with Pouch Attachment Ladder System (PALS). Double-walled and multi-layer construction is required throughout all items to ensure durability. All stitching shall conform to ASTM 6193 lockstitch type 301. Stitching shall conform to 8-10 stitches per inch, without loose ends, runoffs, bunching or other defects. Box stitching or triple back tacks are required at all high stress points to ensure durability. Backstitching or overstitching is required to prevent raveling and provide reinforcement. Thread ends shall be trimmed to 1/16 inch maximum. Raw edges shall be turned under, heat sealed, and/or bound with binding tape to prevent unraveling. Woven and dyed materials shall be free of pattern markings, needle holes, tears or other defects that affect performance or durability. Fabric requires water repellent finish. The DF-LCS shall be treated for Near Infrared spectral Reflectance (NIR). The DF-LCS shall be fully modular with standard Modular Lightweight Load-Carrying Equipment (MOLLE) and All-Purpose Lightweight Individual Carrying Equipment (ALICE) legacy system.

Materials Requirements List (applies to all items)

a. 1000 denier Cordura (or the like) in Air Force Digital Tiger Stripe (AFDTS) print (MIL-C-43734 Class III)

b. Nylon Webbing, Foliage 504 (A-A-55301, MIL-W-17337 Class 2)

c. Binding Tape, Foliage 504 (MIL-PRF-5038 Type III)

d. Hook and Loop, Foliage 504 (AA-55126 Type II Class 1)

e. Mesh, Foliage 504 (MIL-C-8061 Type II)

f. Thread, Foliage Size tex no. 68 (nominal) (also identified as Size E)

g. Bungee and Elastic, Foliage 504 (MIL-PRF-5664 Type II Class 1)

h. Plastic Hardware, Foliage 504

i. Eyelets and Snap Fasteners, brass with black chemical finish, button cap shells should have a Foliage 504 baked-on enamel finish (MS-27980-1B, MS-27980-2B, MS-27980-6B, MS-27980-7B, MS-27980-8B)

j. Zipper closure shall be stainless steel (Foliage 504)

NOTE: Air Force Sage Green 1641 may be used instead of Foliage 504

Test Requirements (applies to all items)

The Air Force reserves the right to have all submittals independently tested to ensure construction and materials requirements are met. Along with the requested sample, each offeror shall submit independent lab test reports, applicable certifications for materials, and a statement of construction techniques.

General Salient Characteristics:

All items shall be fully functional in all climates and environment conditions, to include, but not limited to: tropical, desert, rain, snow, sand, high temperature/humidity, etc.

Except where mesh specified, all pouches and holders shall have a grommet emplaced at the bottom for liquid drainage.

All pouches and holders shall use PALS.

All pouches and holders shall allow user to access its contents while wearing Mission-Oriented-Protective-Posture (MOPP) gloves and tactical gloves.

Pouches and holders shall have a single closure device that doesn’t rust, dent, misshape, and keeps contents secure within the pouch. Note, some pouches require a specific type of closure (e.g., zipper).

Specific Salient Characteristic for each item:

Rifleman Kit

H-Gear

Large/X-Large for 5’6” person and up with adjustable elastic for 32-42” size waist

Harness shall have Pouch Attachment Ladder System (PALS) webbing on shoulder straps and waist panels

Harness shall have mesh back panel with PALS webbing

Harness shall fit over shoulders and be adjustable to securely fit body

Harness shall have a grommet emplaced at the bottom for liquid drainage

Harness shall have a drag strap

H-Gear

Small/Medium for 4’11”-5’5” person with adjustable elastic waist for 26-36” waist

Harness shall have PALS webbing on shoulder straps and waist panels

Harness shall have mesh back panel with PALS webbing

Harness shall fit over shoulders and be adjustable to securely fit body

Harness shall have a grommet emplaced at the bottom for liquid drainage

Harness shall have a drag strap

Single Pocket M-4 Triple Magazine Pouch

Pouch shall hold three magazines per pouch

Pouch shall have an external retention device (e.g., elastic straps or bungee cord)

Single Fragmentation Grenade Pouch

Pouch shall hold one fragmentation grenade per pouch

1 Quart Canteen (w/cup)/General Purpose Pouch

Pouch shall have an external retention device (e.g., bungee cord)

Pouch shall have a mesh emplaced at the bottom for liquid drainage

All-Purpose Lightweight Individual Carrying Equipment (ALICE) Adaptor

Adaptor shall use the PALS

Adaptor shall be compatible with legacy equipment using ALICE clips

Single Pocket M-4 Double Magazine Pouch

Pouch shall hold two magazines per pouch

Pouch shall have an external retention device (e.g., elastic straps or bungee cord)

Medical Pouch/Bleeder Control

Pouch shall have a zipper closure device

Hydration Pouch

Pouch shall hold one 100 oz hydration kit

Protective Insert

Protective insert shall insert into 1 quart canteen pouch and convert to a general pouch for tactical gear (e.g., night vision goggles)

Insert shall have a grommet emplaced at the bottom for liquid drainage

Single Pocket M9 Single Magazine Pouch

Pouch shall hold one magazine per pouch

Chemical Spray Holder

Holder shall hold one 4 oz chemical spray container

Expandable Baton Holder

Holder shall one 6” collapse baton

Expandable Baton Holder

Holder shall one 8” collapse baton Joint Tactical Radio System (JTRS) Pouch

Pouch shall have an external retention device (e.g., elastic straps or bungee cord)

Dual Hand Cuff Pouch

Pouch holds two hand cuffs per pouch

Utility Pouch

Pouch dimension shall be approximately 9”L x 3”W x 5”H

Pouch shall have a zipper closure device

Dual Pocket M9 Single Magazine Pouch with Kydex Insert

Pouch shall hold 2 magazines per pouch

Latex Glove Pouch

Pouch shall hold at least 10 latex gloves per pouch Team Leader Kit

Pop Flare pouch

Pouch shall hold one pop flare per pouch

Single Smoke Grenade Pouch

Pouch shall hold one smoke grenade per pouch

Pouch shall have an external retention device (e.g., elastic straps)

M-203 Grenadiers Kit

Triple 40 mm Round Pouch

Pouch shall hold three 40 mm rounds per pouch

M-249 Saw Gunner Kit

Utility Pouch

Pouch dimension shall be approximately 9”L x 3”W x 5”H

Pouch shall have a zipper closure device

Ammo Pouch Squad Automatic Weapon (SAW) 200 Rounds

Pouch shall hold one 200 round per pouch

Utility Pouch

Pouch dimensions shall be approximately 5”L x 3”W x 5”H

M-240 Machine Gunner Kit

Ammo Pouch M-240 100 Rounds

Pouch shall hold one 100 rounds per pouch

Utility Pouch

Pouch dimension shall be approximately 9”L x 3”W x 5”H

Pouch shall have a zipper closure device

Multi-Mission Kit

Multi-Mission Pack

Pack shall have a main compartment

Pack shall have three outer pockets

Pack shall have two external side slide pockets with PALS webbing for MOLLE attachment

Pack shall have two internal side slide pockets

Pack shall have one internal pocket with PALS webbing attached to main compartment flap

Pack shall have a padded shoulder straps and waist belt

Pack shall have side retention straps

Pack dimension shall be approximately 23.5”L x 16”W x 15”H

Pack shall have PALS webbing for MOLLE attachments

Pack shall have an internal hydration pouch

Pack shall have a grommet emplaced at the bottom for liquid drainage

Pack shall allow user to access its contents while wearing MOPP gloves and tactical gloves

Multi-Mission Pack-Small Accessory Pouch

Pouch dimensions shall be approximately 13.5”L x 7.5” x 7” H

Pouch shall have a zipper closure device

Utility Pouch

Pouch dimensions shall be approximately 9”L x 3”W x 5”H

Pouch shall have a zipper closure device

Military Working Dog Kit

Patrol Med Kit Pouch

Pouch shall have a drop leg adapter

Pouch shall have a zipper closure device

2 Quart Canteen Pouch

Pouch shall hold one 2 quart canteen

Utility Pouch

Pouch dimensions shall be approximately 5”L x 3”W x 5”H

Flashlight Holder

Holder shall hold one flashlight

Load Out Bag

Bag shall have large main compartment to store complete deployment equipment?

Bag dimension shall be approximately 30”Lx 16”W x 12”H

Bag shall have a “U” shaped opening with zipper closure?

Bag shall be constructed with wheels and reinforced (e.g., aluminum) skid plate

Bag shall have internal or external pockets

Bag shall have two handles and pull/top grab handle

Padded Equipment Belt Salient Characteristics for all sizes:

Belt shall be used as a sleeve over duty belt

Belt shall be tapered at top and straight at bottom

Belt shall have PALS webbing for pouches and padding for comfort

Belt shall allow a 2” duty (pistol) belt to securely fit

Belt shall have three to four rows of PALS webbing

Belt shall have a sleeve to slide in rigid duty (pistol) belt

Belt shall have two cut out to allow mounting a holster to internal duty (pistol) belt

Belt shall have inside surface lined with moisture wicking material or mesh

Padded Equipment Belt Salient Characteristic for each size:

Padded Equipment Belt (Small)

Belt dimensions shall be approximately 27.5”L, 5.5”W in the middle, 3.5”W in the front

Padded Equipment Belt (Medium)

Belt dimensions shall be approximately 32.5”L, 5.5”W in the middle, 3.5”W in the front

Padded Equipment Belt (Large)

Belt dimensions shall be approximately 38.5”L, 5.5”W in the middle, 3.5”W in the front

Padded Equipment Belt (Extra Large)

Belt dimensions shall be approximately 43.5”L, 5.5”W in the middle, 3.5”W in the front

(End of Summary of Changes)