Draft Spec Notice KIMBALL FY23 (JS).pdf

PRE-SOLICITATION

USCGC KIMBALL (WMSL 756)

DRYDOCK REPAIRS FY23

1 (Rev-0)

The purpose of this notice is to provide a draft specification for 70Z08023KIMBALLDD.

Pursuant to FAR Part 5.205(c) and FAR 15.201, the purpose of this notice is to determine if there are any concerns regarding the potential acquisition strategy should a solicitation be produced as a result of this draft specification. .

REQUIREMENT: This notice is issued by the U.S. Coast Guard, Surface Forces

Logistics Center, and Norfolk, VA to identify concerns for potentially producing a solicitation for the following items:

DRYDOCK REPAIRS SPECIFICATION: (Subject to change at the discretion of the

Government). Contractor may be requested to provide all necessary facilities, materials, equipment, and personnel to perform DRYDOCK repairs to the U.S. Coast Guard Cutter

(USCGC) KIMBALL (WMSL 418). The vessel is home ported in HONOLULU, HI. All work will be performed at the contractor facility. All DD work for these cutters during

FY23-FY24 are restricted to a shipyard within a 50-mile commuting radius of the vessel’s’ homeport of Honolulu, HI as a necessary military consideration in order to maximize the operational readiness of the vessels to complete mission requirements and maintain crew proficiency standards.

SCOPE OF WORK: The scope of the acquisition is for the DRYDOCK repairs of the

USCGC KIMBALL (WMSL 418). This work may will include, but is not limited to the following Work Items:

Definite Items

WORK ITEM 1: Hull 3D, Laser Scan

WORK ITEM 2: Hull Plates (Freeboard), Inspect

WORK ITEM 3: Hull Plates (U/W Body), Inspect

WORK ITEM 4: Freeboard, Preserve (Full) WORK ITEM 5: Superstructure, Preserve

(Partial)

WORK ITEM 6: U/W Body Hull, Preserve (Full)

WORK ITEM 7: Tenting, Provide

WORK ITEM 8: Tenting (Mast), Provide

WORK ITEM 9: Propulsion Shaft Fairwaters And Rope Guards, Inspect

WORK ITEM 10: Chain Lockers and Sump, Preserve

WORK ITEM 11: Chain Lockers and Sump, Clean and Inspect

WORK ITEM 12: Voids (Non-Accessible), Preserve WORK ITEM 13: Voids (Non-

Accessible), Leak Test

WORK ITEM 14: Sideport Shell Door, Level 2, Inspect

WORK ITEM 15: Mast, Preserve

WORK ITEM 16: Propulsion Shaft Alignment & Bearings (External) Clearances, Check

WORK ITEM 17: Propulsion Shaft Coverings (MIL-STD-2199B), Inspect and Repair

2 (Rev-0)

WORK ITEM 18: Propulsion Shaft Seals (Mechanical), Overhaul

WORK ITEM 19: Controllable Pitch Propeller Hub Assembly, General Maintenance

WORK ITEM 20: Controllable Pitch Propeller System, Perform General Maintenance

WORK ITEM 21: Doppler Speed Log Valve, Overhaul WORK ITEM 22: Doppler Speed

Log, General Maintenance

WORK ITEM 23: Fathometer Transducer (Deep Water), General Maintenance

WORK ITEM 24: Shallow Water Transducer, Renew WORK ITEM 25: Sea Valves and

Waster Pieces, Overhaul Or Renew

WORK ITEM 26: Seawater Strainers (All Sizes), Overhaul and Inspect 170

WORK ITEM 27: Rudder Stock Bearings, Check Clearances

WORK ITEM 28: Rudder Stock Seals, Overhaul WORK ITEM 29: Steering System, Inspect and Service

WORK ITEM 30: Bow Thruster Unit (General), Overhaul

WORK ITEM 31: Anchors Chains and Ground Tackles, Inspect and Preserve

WORK ITEM 32: Impressed Current Cathodic Protection System Dielectric Shield

(Capastic Fairing), Renew

WORK ITEM 33: Impressed Current Cathodic Protection System, Inspect and Maintain

WORK ITEM 34: Cathodic Protection (Zincs), Renew WORK ITEM 35: Impressed

Current Cathodic Protection System Anodes, Renew

WORK ITEM 36: Impressed Current Cathodic Protection System Reference Cells, WORK ITEM 37: Ship Service Diesel Generator (No. 3) Exhaust Piping, Modify

WORK ITEM 38: Transom Double Doors and Tow Outfits, Modify

WORK ITEM 39: Stern Door Hydraulic and Control System, Modify WORK ITEM 40:

Stern Ramp Rails, Modify

WORK ITEM 41: Cascade Orificial Resistive Device, Clean And Inspect

WORK ITEM 42: Deck Covering (Slip-Resistant) Mast, Preserve

WORK ITEM 43: Drydocking, Accomplish

WORK ITEM 44: Vessel in Drydock Temporary Services, Provide

WORK ITEM 45: Sea Trial Performance, Support, Provide

ANTICIPATED PERIOD OF PERFORMANCE: The period of performance is anticipated to be for (83) calendar days with a start date 07 December 2022 and end date of 01 March 2023. (Subject to change at the discretion of the Government)

ANTICIPATED NAICS CODE/SIZE STANDARD: The anticipated applicable

NAICS Code is 336611, Ship Building and Repairing and the size standard is 1,250 employees.

3 (Rev-0)

Disclaimer and Important Notes: This Notice does not constitute a Request for

Proposal/Quotation; and, it is not considered to be a commitment by the Government to award a contract nor will the Government pay for any information provided; no basis for claim against the Government shall arise as a result from draft specification or

Government use of any information provided. Interested parties are advised that the

Government is under no obligation to acknowledge receipt of any information received or provide feedback to respondents with respect to any information submitted. At this time no solicitation exists; therefore, Do Not Request a Copy of the Solicitation.