Combined Synopsis Solicitation Hardware SPMYM324Q4004.docx

SPMYM3-24-Q-4004

JML: 32744041

This is a COMBINED SYNOPSIS/SOLICITATION for commercial items prepared in accordance with the information in FAR part 12, using Simplified Acquisition Procedures under found at FAR 13, as supplemented with the additional information included in this notice. This announcement constitutes the only solicitation; a written solicitation will not be issued. PAPER COPIES OF THIS SOLICITATION WILL NOT BE AVAILABLE. This combined synopsis/solicitation SHALL be posted to BETASAM. The RFQ number is SPMYM3-24-Q-4004. This solicitation documents and incorporates provisions and clauses in effect through FAC 2023-05 and DFARS Change Notice 20230929. It is the responsibility of the contractor to be familiar with the applicable clauses and provisions. The clauses may be accessed in full text at this address: https://www.ecfr.gov. The FSC Code is 5305 and the NAICS code is 332722 and the Small Business Standard is 600 employees. This requirement is being processed utilizing a total small business set-aside.

The evaluation criteria is Lowest Price Technically Acceptable (LPTA). PPIRS will be used to determine vendor responsibility. Potential contractors will be screened for responsibility in accordance with FAR 9.104.

This is to be evaluated as “All or None”

Place of Manufacture / Country of Origin Required.

Quotes must be e-mailed to gary.1.chandler@dla.mil and also DLA-KME-QUOTATIONS@DLA.MIL

**Note: Vendor shall list the country of origin for each line item

A reverse auction may be held.

The Portsmouth Naval Shipyard requests responses from qualified sources capable of providing:

MATERIAL INFORMATION

ITEM DESCRIPTION U/I QTY UNIT PRICE TOTAL

0001 FLAT SOCKET HEAD CAPSCREW S/L EA 1

FLAT SOCKET HEAD SELF-LOCKING CAPSCREW, 3/4-10UNC-2A X 1-1/8 IN LG. MIL-DTL-1222J TYPE-II. NOTE: FULL FORMED THREAD LENGTH OF 3/8” ONLY IS REQUIRED. MATERIAL TO BE NICKEL-COPPER-ALUMINUM ALLOY QQ-N-286G. MINIMUM YIELD MUST BE 90,000 PSI. MAKE SELF-LOCKING IAW MIL-DTL-18240F(1) TYPE-ANY. MARKINGS OF A MINIMUM (6) DOTS (APPROXIMATELY 0.032 DIA) RAISED OR DEPRESSED (APPROXIMATELY 0.010) SHALL BE PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED. SIDE LOCATION IF NECESSARY).

0002 FLAT SOCKET HEAD CAPSCREW S/L EA 590

FLAT SOCKET HEAD SELF-LOCKING CAPSCREW, 3/4-10UNC-2A X 1-3/4 IN LG. MIL-DTL-1222J TYPE-II. NOTE: FULL FORMED THREAD LENGTH OF 1” ONLY IS REQUIRED. MATERIAL TO BE NICKEL-COPPER-ALUMINUM ALLOY QQ-N-286G. MINIMUM YIELD MUST BE 90,000 PSI. MAKE SELF-LOCKING IAW MIL-DTL-18240F(1) TYPE-ANY. MARKINGS OF A MINIMUM (6) DOTS (APPROXIMATELY 0.032 DIA) RAISED OR DEPRESSED (APPROXIMATELY 0.010) SHALL BE PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED. SIDE LOCATION IF NECESSARY).

0003 FLAT SOCKET HEAD CAPSCREW S/L EA 8

FLAT SOCKET HEAD CAPSCREWS SELF LOCKING, 3/4-10UNC-2A X 1-3/8 IN LG. MIL-DTL-1222J TYPE-II. NOTE: FULL FORMED THREAD LENGTH OF 5/8” ONLY IS REQUIRED. MATERIAL TO BE NICKEL-COPPER-ALUMINUM ALLOY QQ-N-286G. MINIMUM YIELD MUST BE 90,000 PSI. MAKE SELF-LOCKING IAW MIL-DTL-18240F(1) TYPE-ANY. MARKINGS OF A MINIMUM (6) DOTS (APPROXIMATELY 0.032 DIA) RAISED OR DEPRESSED (APPROXIMATELY 0.010) SHALL BE PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED. SIDE LOCATION IF NECESSARY).

0004 SOCKET FLAT COUNTERSUNK HEAD EA 24

CAP SCREW ANGLE SLF LKG

SOCKET FLAT COUNTERSUNK HEAD CAP SCREW ANGLE SELF LOCKING,

1/2-13UNC-3A X 1-5/8 IN. LG. MFR IAW FF-S-86H TYPE IV. NOTE THAT PARA 3.1.4 & PARA.

3.2.5 OF FF-S-86H IS IN ERROR. FASTENERS ARE TO MEET THE REQUIREMENTS OF

TABLE X NOT TABLE VIII. MAT’L IS NICU ALLOY, QQ-N-281D AMEND 2 CL-A. SELF LOCKING IAW MIL-DTL-18240F AMEND 1 TYPE “N”. MARKINGS OF A MINIMUM 6 DOTS (APPROX. 0.032) RAISED OR DEPRESSED (APPROX. 0.010) SHALL BE PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED, SIDE LOCATION IF NECESSARY).

0005 SOCKET FLAT COUNTERSUNK HEAD EA 9

CAP SCREW ANGLE SLF LKG

SOCKET FLAT COUNTERSUNK HEAD CAP SCREW ANGLE SELF LOCKING,

5/8-11UNC-2A X 1-7/8 IN. LG. MFR IAW FF-S-86H TYPE IV. NOTE THAT PARA 3.1.4 & PARA.

3.2.5 OF FF-S-86H IS IN ERROR. FASTENERS ARE TO MEET THE REQUIREMENTS OF

TABLE X NOT TABLE VIII. MAT’L IS NICU ALLOY, QQ-N-281D AMEND 2. SELF LOCKING

IAW MIL-DTL-18240F AMEND 1 TYPE “N”. MARKINGS OF A MINIMUM 6 DOTS (APPROX.

0.032) RAISED OR DEPRESSED ( APPROX. 0.010) SHALL BE PLACED ON THE HEAD OF THE

FASTENER (TOP PREFERRED, SIDE LOCATION IF NECESSARY).

0006 SOCKET FLAT COUNTERSUNK HEAD EA 40

CAP SCREW ANGLE SLF LKG

SOCKET FLAT COUNTERSUNK HEAD CAP SCREW ANGLE SELF LOCKING,

3/4-10UNC-2A X 2-1/8 IN. LG. MFR IAW FF-S-86H TYPE IV. NOTE THAT PARA 3.1.4 & PARA.

3.2.5 OF FF-S-86H IS IN ERROR. FASTENERS ARE TO MEET THE REQUIREMENTS OF

TABLE X NOT TABLE VIII. MAT’L IS NICU ALLOY, QQ-N-281D AMEND 2. SELF LOCKING

IAW MIL-DTL-18240F AMEND 1 TYPE “N”. MARKINGS OF A MINIMUM 6 DOTS (APPROX.

0.032) RAISED OR DEPRESSED ( APPROX. 0.010) SHALL BE PLACED ON THE HEAD OF THE

FASTENER (TOP PREFERRED, SIDE LOCATION IF NECESSARY).

0007 SPECIAL FLAT HEAD S/L CAPSCREW EA 12

SPECIAL FLAT HEAD SELF-LOCKING CAPSCREW, 5/8-11UNC-3A X 2-1/2 IN. LONG.

MANUFACTURE IA W DETAIL4-2C OF DWG 100-5858019 REV J. MATERIAL REQUIRED TO

BE NICUAL QQ-N-286G, ANNEALED. MAKE SELF-LOCKING IA W MIL-DTL-18240F(l) TYPEN(

MOD). MOD IS CENTER LINE OF PELLET REQUIRED TO BE 3/8 IN. FROM THE END

OF SCREW. MARKINGS OF A MINIMUM 6 DOTS( APPROX. 0.032) RAISED OR DEPRESSED (

APPROX. 0.010) SHALL BE PLACED ON THE HEAD OF THE FAS TENER (TOP PREFERRED,

SIDE LOCATION IF NECESSARY).

0008 SPECIAL FLAT HEAD S/L CAPSCREW EA 7

SPECIAL FLAT HEAD SELF-LOCKING CAPSCREW, 5/8-11UNC-3A X 2-1/2 IN. LONG.

MANUFACTURE IA W DETAIL4-2C OF DWG 100-5858019 REV J. MATERIAL REQUIRED TO

BE NICUAL QQ-N-286G, ANNEALED. MAKE SELF-LOCKING IA W MIL-DTL-18240F(l) TYPEN(

MOD). MOD IS CENTER LINE OF PELLET REQUIRED TO BE 3/8 IN. FROM THE END

OF SCREW. MARKINGS OF A MINIMUM 6 DOTS( APPROX. 0.032) RAISED OR DEPRESSED (

APPROX. 0.010) SHALL BE PLACED ON THE HEAD OF THE FAS TENER (TOP PREFERRED,

SIDE LOCATION IF NECESSARY).

0009 SPECIAL FLAT HEAD S/L CAPSCREW EA 12

SPECIAL FLAT HEAD SELF-LOCKING CAPSCREW, 5/8-11UNC-3A X 2-1/2 IN. LONG.

MANUFACTURE IA W DETAIL4-2C OF DWG 100-5858019 REV J. MATERIAL REQUIRED TO

BE NICUAL QQ-N-286G, ANNEALED. MAKE SELF-LOCKING IA W MIL-DTL-18240F(l) TYPEN(

MOD). MOD IS CENTER LINE OF PELLET REQUIRED TO BE 3/8 IN. FROM THE END

OF SCREW. MARKINGS OF A MINIMUM 6 DOTS( APPROX. 0.032) RAISED OR DEPRESSED (

APPROX. 0.010) SHALL BE PLACED ON THE HEAD OF THE FAS TENER (TOP PREFERRED,

SIDE LOCATION IF NECESSARY).

0010 SPECIAL FLAT HEAD S/L CAPSCREW EA 12

SPECIAL FLAT HEAD SELF-LOCKING CAPSCREW, 5/8-11UNC-3A X 2-1/2 IN. LONG.

MANUFACTURE IAW DETAIL4-2Cl OF DWG 100-5858019 REV J. MATERIAL REQUIRED TO BE NICUAL QQ-N-286G, ANNEALED. MAKE SELF-LOCKING IAW MIL-DTL-18240F(l)

TYPE-N(MOD). MOD IS CENTER LINE OF PELLET REQUIRED TO BE 3/8 IN. FROM THE

END OF SCREW. MARKINGS OF A MINIMUM 6 DOTS( APPROX. 0.032) RAISED OR

DEPRESSED ( APPROX. 0.010) SHALL BE PLACED ON THE HEAD OF THE FASTENER (TOP

PREFERRED, SIDE LOCATION IF NECESSARY).

0011 FLAT SOCKET HEAD S/L CAPSCREW EA 70

FLAT SOCKET HEAD SELF-LOCKING CAPSCREW, 0.500-13UNC-2A X 1.500 IN LG. MIL-DTL-1222J TYPE-II. MATERIAL IS NICKEL-COPPER-ALUMINUM ALLOY QQ-N-286G. MAKE SELFLOCKING IAW MIL-DTL-18240F(1) TYPE “N”. MARKINGS OF A MINIMUM (6) DOTS

(APPROXIMATELY 0.032 DIA) RAISED OR DEPRESSED (APPROXIMATELY 0.010) SHALL BE

PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED. SIDE LOCATION IF

NECESSARY).

0012 FLAT SOCKET HEAD S/L CAPSCREW EA 70

FLAT SOCKET HEAD SELF-LOCKING CAPSCREW, 0.500-13UNC-2A X 1.500 IN LG. MIL-DTL-1222J TYPE-II. MATERIAL IS NICKEL-COPPER-ALUMINUM ALLOY QQ-N-286G. MAKE SELFLOCKING IAW MIL-DTL-18240F(1) TYPE “N”. MARKINGS OF A MINIMUM (6) DOTS

(APPROXIMATELY 0.032 DIA) RAISED OR DEPRESSED (APPROXIMATELY 0.010) SHALL BE

PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED. SIDE LOCATION IF

NECESSARY).

0013 SOCKET FLAT COUNTERSUNK HEAD EA 55

S/L CAP SCREW ANGLE

SOCKET FLAT COUNTERSUNK HEAD SELF LOCKING CAP SCREW ANGLE, 0.625-11UNRC-3A X 2.750 IN LG. FF-S-86H TYPE IV. NOTE THAT PARA 3.1.4 & PARA. 3.2.5 OF FF-S-86H IS IN ERROR. FASTENERS ARE TO MEET THE REQUIREMENTS OF TABLE X NOT TABLE VIII. MATERIAL TO BE NICKEL-COPPER-ALUMINUM ALLOY QQ-N-286G. MAKE SELF-LOCKING IAW MIL-DTL-18240F(1) TYPE-ANY. MARKINGS OF A MINIMUM (6) DOTS (APPROXIMATELY 0.032 DIA) RAISED OR DEPRESSED (APPROXIMATELY 0.010) SHALL BE PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED. SIDE LOCATION IF NECESSARY).

0014 SOCKET FLAT COUNTERSUNK HEAD EA 53

S/L CAP SCREW ANGLE

SOCKET FLAT COUNTERSUNK HEAD SELF LOCKING CAP SCREW ANGLE, 0.625-11UNRC-3A X 2.750 IN LG. FF-S-86H TYPE IV. NOTE THAT PARA 3.1.4 & PARA. 3.2.5 OF FF-S-86H IS IN ERROR. FASTENERS ARE TO MEET THE REQUIREMENTS OF TABLE X NOT TABLE VIII. MATERIAL TO BE NICKEL-COPPER-ALUMINUM ALLOY QQ-N-286G. MAKE SELF-LOCKING IAW MIL-DTL-18240F(1) TYPE-ANY. MARKINGS OF A MINIMUM (6) DOTS (APPROXIMATELY 0.032 DIA) RAISED OR DEPRESSED (APPROXIMATELY 0.010) SHALL BE PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED. SIDE LOCATION IF NECESSARY).

0015 SOCKET FLAT COUNTERSUNK HEAD EA 17

CAP SCREW ANGLE SELF-LOCKING

SOCKET FLAT COUNTERSUNK HEAD CAP SCREW ANGLE SELF-LOCKING,

1/2-13UNC-3A X 2 IN LONG. MFR. IAW FF-S-86H TYPE IV. NOTE THAT PARA 3.1.4 & PARA.

3.2.5 OF FF-S-86H IS IN ERROR. FASTENERS ARE TO MEET THE REQUIREMENTS OF

TABLE X NOT TABLE VIII. MATERIAL IS NICKEL-COPPER ALLOY, QQ-N-281D AMEND 2.

SELF-LOCKING IAW MIL-DTL-18240F AMEND 1 TYPE “L OR P”. MARKINGS OF A MINIMUM (6) DOTS (APPROXIMATELY 0.032 DIA) RAISED OR DEPRESSED (APPROXIMATELY 0.010) SHALL BE PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED. SIDE LOCATION IF

NECESSARY).

0016 SOCKET FLAT COUNTERSUNK HEAD EA 42

CAP SCREW ANGLE SELF-LOCKING

SOCKET FLAT COUNTERSUNK HEAD CAP SCREW ANGLE SELF-LOCKING,

1/2-13UNC-3A X 1-9/16 IN LONG. MFR. IAW FF-S-86H TYPE IV. NOTE THAT PARA 3.1.4 &

PARA. 3.2.5 OF FF-S-86H IS IN ERROR. FASTENERS ARE TO MEET THE

REQUIREMENTS OF TABLE X NOT TABLE VIII. MATERIAL IS NICKEL-COPPER ALLOY,

QQ-N-281D AMEND 2. SELF LOCKING IAW MIL-DTL-18240F AMEND 1 TYPE “L OR P”.

MARKINGS OF A MINIMUM (6) DOTS (APPROXIMATELY 0.032 DIA) RAISED OR

DEPRESSED (APPROXIMATELY 0.010) SHALL BE PLACED ON THE HEAD OF THE

FASTENER (TOP PREFERRED. SIDE LOCATION IF NECESSARY).

0017 SOCKET FLAT COUNTERSUNK HEAD EA 28

CAP SCREW ANGLE SELF-LOCKING

SOCKET FLAT COUNTERSUNK HEAD CAP SCREW ANGLE SELF-LOCKING,

1/2-13UNC-3A X 1-3/8 IN LONG. MFR. IAW FF-S-86H TYPE IV. NOTE THAT PARA 3.1.4 &

PARA. 3.2.5 OF FF-S-86H IS IN ERROR. FASTENERS ARE TO MEET THE REQUIREMENTS OF TABLE X NOT TABLE VIII. MATERIAL IS NICKEL-COPPERALUMINUM ALLOY, QQ-N-286G. ALSO NOTE THAT PARA. 3.5.6 OF FF-S-86H IS IN ERROR, MATERIAL MARKINGS ON THE HEAD OF THE FASTENERS TO BE NOT JUST K. SELF LOCKING IAW MIL-DTL-18240F AMEND 1 TYPE “L OR P”. MARKINGS OF A MINIMUM (6) DOTS (APPROXIMATELY 0.032 DIA) RAISED OR DEPRESSED (APPROXIMATELY 0.010) SHALL BE PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED. SIDE LOCATION IF NECESSARY).

0018 SOCKET FLAT COUNTERSUNK HEAD EA 17

SELF-LOCKING CAP SCREW ANGLE

SOCKET FLAT COUNTERSUNK HEAD SELF-LOCKING CAP SCREW ANGLE,

5/8-11UNC-3A X 1-1/2 IN. LG. MFR IAW FF-S-86H TYPE IV. NOTE THAT PARA 3.1.4 & PARA.

3.2.5 OF FF-S-86H IS IN ERROR. FASTENERS ARE TO MEET THE REQUIREMENTS OF

TABLE X NOT TABLE VIII. ALSO NOTE THAT PARA 3.5.6 OF FF-S-86H IS IN ERROR AND

THAT MATERIAL MARKINGS ON THE HEAD OF THE FASTENERS TO BE NOT

JUST K. MAT’L IS NICUAL ALLOY, QQ-N-286G, ANNEALED AND AGE HARDENED. SELF

LOCKING IAW MIL-DTL-18240F(1) TYPE “L OR P”. MARKINGS OF A MINIMUM (6) DOTS

(APPROXIMATELY 0.032 DIA) RAISED OR DEPRESSED (APPROXIMATELY 0.010) SHALL BE

PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED. SIDE LOCATION IF

NECESSARY).

0019 SOCKET FLAT COUNTERSUNK HEAD EA 17

SELF-LOCKING CAP SCREW ANGLE

SOCKET FLAT COUNTERSUNK HEAD SELF-LOCKING CAP SCREW ANGLE,

5/8-11UNC-3A X 1-1/2 IN. LG. MFR IAW FF-S-86H TYPE IV. NOTE THAT PARA 3.1.4 & PARA.

3.2.5 OF FF-S-86H IS IN ERROR. FASTENERS ARE TO MEET THE REQUIREMENTS OF

TABLE X NOT TABLE VIII. ALSO NOTE THAT PARA 3.5.6 OF FF-S-86H IS IN ERROR AND

THAT MATERIAL MARKINGS ON THE HEAD OF THE FASTENERS TO BE NOT

JUST K. MAT’L IS NICUAL ALLOY, QQ-N-286G, ANNEALED AND AGE HARDENED. SELF

LOCKING IAW MIL-DTL-18240F(1) TYPE “L OR P”. MARKINGS OF A MINIMUM (6) DOTS

(APPROXIMATELY 0.032 DIA) RAISED OR DEPRESSED (APPROXIMATELY 0.010) SHALL BE

PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED. SIDE LOCATION IF

NECESSARY).

0020 SOCKET FLAT COUNTERSUNK HEAD EA 17

SELF-LOCKING CAP SCREW ANGLE

SOCKET FLAT COUNTERSUNK HEAD SELF-LOCKING CAP SCREW ANGLE,

5/8-11UNC-3A X 1-1/2 IN. LG. MFR IAW FF-S-86H TYPE IV. NOTE THAT PARA 3.1.4 & PARA.

3.2.5 OF FF-S-86H IS IN ERROR. FASTENERS ARE TO MEET THE REQUIREMENTS OF

TABLE X NOT TABLE VIII. ALSO NOTE THAT PARA 3.5.6 OF FF-S-86H IS IN ERROR AND

THAT MATERIAL MARKINGS ON THE HEAD OF THE FASTENERS TO BE NOT

JUST K. MAT’L IS NICUAL ALLOY, QQ-N-286G, ANNEALED AND AGE HARDENED. SELF

LOCKING IAW MIL-DTL-18240F(1) TYPE “L OR P”. MARKINGS OF A MINIMUM (6) DOTS

(APPROXIMATELY 0.032 DIA) RAISED OR DEPRESSED (APPROXIMATELY 0.010) SHALL BE

PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED. SIDE LOCATION IF

NECESSARY).

0021 SPECIAL FLAT HEAD S/L CAPSCREW EA 10

SPECIAL FLAT HEAD SELF-LOCKING CAPSCREW, 5/8-11UNC-3A X 2-1/2 IN LG.

MANUFACTURE IAW DETAIL4-2C OF DWG 100-5858019/J. MATERIAL REQUIRED TO BE

NICUAL QQ-N-286G, ANNEALED. MAKE SELF-LOCKING IAW MIL-DTL-18240F(1) TYPE-N (

MOD). MOD IS CENTER LINE OF PELLET REQUIRED TO BE 3/8 IN. FROM THE END

OF SCREW. MARKINGS OF A MINIMUM (6) DOTS (APPROXIMATELY 0.032 DIA) RAISED

OR DEPRESSED (APPROXIMATELY 0.010) SHALL BE PLACED ON THE HEAD OF THE

FASTENER (TOP PREFERRED. SIDE LOCATION IF NECESSARY).

0022 HEX HEAD S/L CAPSCREW EA 60

HEX HEAD SELF LOCKING CAPSCREW, 5/8-11UNC-2A X 2 IN LG. MANUFACTURE IAW

MIL-DTL-1222J TYPE I. MATERIAL IS NICKEL COPPER, QQ-N-281D AMEND 2, CLASS A.

SELF-LOCKING IAW MIL-DTL-18240F AMEND 1 TYPE “L” (MOD) MOD LOCATION OF

SLOT IS IAW DETAIL 2-4A OF DWG 600-6160946 REV D & STRIP IS REQUIRED TO BE

MIN OF 1/2 IN LG. MARKINGS OF A MINIMUM (6) DOTS (APPROXIMATELY 0.032 DIA)

RAISED OR DEPRESSED (APPROXIMATELY 0.010) SHALL BE PLACED ON THE HEAD OF

THE FASTENER (TOP PREFERRED. SIDE LOCATION IF NECESSARY).

0023 SOCKET FLAT COUNTERSUNK HEAD EA 10

CAP SCREW ANGLE

SOCKET FLAT COUNTERSUNK HEAD CAP SCREW ANGLE, 0.500-13UNRC-3A X 1.750 IN. LONG. FF-S-86H TYPE-IV. NOTE THAT PARA 3.1.4 & PARA. 3.2.5 OF FF-S-86H IS IN ERROR. FASTENERS ARE TO MEET THE REQUIREMENTS OF TABLE X NOT TABLE VIII AND THAT PARA 3.5.6 OF FF-S-86H IS IN ERROR, THAT MATERIAL MARKINGS ON THE HEAD OF THE FASTENERS TO BE NOT JUST K. MATERIAL TO BE NICKEL-COPPER-ALUMINUM ALLOY QQ-N-286G.

0024 FLAT HEAD 82 DEGREE MACHINE SCREW EA 15

FLAT HEAD 82 DEGREE MACHINE SCREW, 1/2-13UNC-2A X 2 IN. LONG. MFR IAW FF-S-92D

TYPE-I, STYLE-2S OR TYPE-III, STYLE-2C, DESIGN-I. MATERIAL IS NICKEL-COPPER-ALUMINUM ALLOY, QQ-N-286G.

0025 HEX HEAD CAP SCREW EA 30

HEX HEAD CAP SCREW, 1/2-13UNC-2A X 1-3/8 IN LONG. MFR IAW MIL-DTL-1222J TY-I.

MATERIAL IS NICKEL-COPPER ALUMINUM ALLOY, QQ-N-286G.

0026 HEX HEAD SLF LKG CAP SCREW EA 6

HEX HEAD SELF LOCKING CAP SCREW, 1-8UNC-2A X 2-1/4 IN. LG. MFR IAW MIL-DTL-1222J

TYPE I. MAT’L IS NICU ALLOY, QQ-N-281D AMEND 2. SELF LOCKING TO BE IAW MIL-DTL-18240F AMEND 1 TYPE “L OR P”. MARKINGS OF A MINIMUM SIX (6) DOTS (APPROX. .032

DIA.) RAISED OR DEPRESSED (APPROX. .010) SHALL BE PLACED ON THE HEAD OF THE

FASTENER (TOP PREFERRED, SIDE LOCATION IF NECESSARY).

0027 SOCKET HEAD CAP SCREW EA 1

SOCKET HEAD CAP SCREW, 1/2-13UNC-2A X 3 IN. LONG. MFR IAW FF-S-86H TYPE VI (MOD). MOD IS THREAD TO EXTENT TO WITHIN 1/4 IN OF THE HEAD. MATERIAL IS NICKELCOPPER ALLOY, QQ-N-281D AMEND 2.

0028 SOCKET HEAD SLF LKG CAP SCREW EA 4

SOCKET HEAD SELF-LOCKING CAP SCREW, 5/8-11UNC-3A X 2-3/8 IN LONG. MFR IAW MIL-DTL-1222J TY-II. MATERIAL IS NICKEL-COPPER ALUMINUM ALLOY, QQ-N-286G. SELF

LOCKING TO BE IAW MIL-DTL-18240F AMEND 1 TYPE “ANY”. MARKINGS OF A MINIMUM

SIX (6) DOTS (APPROX. .032 DIA.) RAISED OR DEPRESSED (APPROX. .010) SHALL BE PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED, SIDE LOCATION IF NECESSARY).

0029 FLAT HEAD 82 DEGREE MACHINE SCREW EA 11

FLAT HEAD 82 DEGREE MACHINE SCREW, 5/8-11UNC-2A X 1-5/8 IN. LG. MFR IAW FF-S-92D, TYPE III (CROSS RECESSED DESIGN I) STYLE 2C (FLAT HEAD 82 DEGREE). MAT’L IS NICUAL ALLOY, QQ-N-286G, CONDITION IS ANNEALED AND AGE HARDENED. MIL-DTL-1222J APPLIES

0030 HEX SOCKET FLAT COUNTERSUNK EA 106

HEAD SELF-LOCKING CAP SCREW

HEXAGON SOCKET FLAT COUNTERSUNK HEAD SELF-LOCKING CAP SCREW,

5/8-11UNC-2A X 2-1/4 IN LONG. MFR IAW MIL-DTL-1222J TY-II. MATERIAL IS NICKEL-COPPER ALUMINUM ALLOY, QQ-N-286G, ANNEALED & AGE HARDENED. SELF LOCKING TO BE IAW MIL-DTL-18240F AMEND 1 TYPE “L OR P”. MARKINGS OF A MINIMUM SIX (6) DOTS (APPROX. .032 DIA.) RAISED OR DEPRESSED (APPROX. .010) SHALL BE PLACED ON THE HEAD OF THE FASTENER (TOP PREFERRED, SIDE LOCATION IF NECESSARY).

0031 HEX HEAD CAP SCREW EA 2

HEX HEAD CAP SCREW, 1-8UNC-2A X 2.50 IN LONG. MFR IAW MIL-DTL-1222J TY-I.

MATERIAL IS NICKEL-COPPER ALLOY, GRADE 400.

0032 DATA REQUIREMENTS ITEMS 0001-0031 EA 1 NSP NSP

A001 EXHIBIT A, SEQ A001

SEE EXHIBIT “A” SEQ A001: CDRL DI-MISC-81356A (CERTIFICATE OF COMPLIANCE)

SEE EXHIBIT “A” SEQ A002: CDRL DI-MISC-80678 (CERTIFICATE / DATA REPORT)

***For Drawings, Submit Completed Security Form AND Your Company’s Approved Form 2345***

NOTE: OFFERORS MUST COMPLETE THE ATTACHED PROVISIONS 52.204-24, 52.204-26, 252.204-7016, AND 252.204-7019 AND INCLUDE THE COMPLETED PROVISIONS WITH

THEIR OFFER.

A small business joint venture offeror must submit, with its offer, the representation required in paragraph (c) of FAR solicitation provision 52.212-3, Offeror Representations and Certifications-Commercial Products and Commercial Services, and paragraph (c) of FAR solicitation provision 52.219-1, Small Business Program Representations, in accordance with 52.204-8(d) and 52.212-3(b) for the following categories:

(A) Small business;

(B) Service-disabled veteran-owned small business;

(C) Women-owned small business (WOSB) under the WOSB Program;

(D) Economically disadvantaged women-owned small business under the WOSB Program; or

(E) Historically underutilized business zone small business.

FAR CLAUSES AND PROVISIONS

52.204-7 System for Award Management 52.204-9 Personal Identity Verification of contractor Personnel 52.204-10 Reporting Executive Compensation and First Tire Subcontract Awards 52.204-13, SAM Maintenance 52.204-19 Incorporation by Reference of Representations and Certifications 52.204-24*See Attachment for this clause 52.204-25*See Attachment for this clause 52.204-26 *See Attachment for this clause 52.209-2 Prohibition on Contracting with Inverted Domestic Corporations- Representation 52.209-10 Prohibition on Contracting with Inverted Domestic Corporations 52.211-14, Notice of Priority Rating 52.211-15, Defense Priority And Allocation Requirements 52.211-17, Delivery of Excess Quantities 52.212-1, Instructions to Offerors 52.212-3 Alt I Instructions to Offerors Evaluation Offeror Reps and Certs 52.212-4, Contract Terms and Conditions – Commercial Items 52.222-22 Previous Contracts & Compliance Reports 52.222-25 Affirmative Action Compliance 52.225-25, Prohibition on Contracting with Entities Engaging in Certain Activities or Transactions Relating to Iran – Reps and Certs 52.232-39, Unenforceability of Unauthorized Obligations 52.232-40 Providing Accelerated Payments to Small Business Subcontractors 52.233-2 Service of Protest 52.242-13 Bankruptcy 52.242-15 Stop Work Order 52.243-1, Changes Fixed Price 52.246-1, Contractor Inspection Requirements 52.247-34, F.O.B—Destination 52.252-1, Solicitation Provisions Incorporated by Reference 52.252-2, Clauses Incorporated by Reference 52.252-6, Authorized Deviations in Clauses 52.253-1, Computer Generated Forms 252.203-7002, Requirement to Inform Employees of Whistleblower Rights 252.203-7005 Representation Relating to Compensation of Former DoD Officials 252.204-7003. Control of Government Personnel Work Product 252.204-7004, System for Award Management 252.204-7008 Compliance With Safeguarding Covered Defense Information Controls 252.223-7008 Prohibition of Hexavalent Chromium 252.204-7011 Alternative Line Item Structure 252.225-7001 Buy American Act & Balance of Payments Program 252.225-7002 Qualifying Country Sources as Subcontractors 252.225-7048 Export-Controlled Items 252.225-7059 Prohibition on Certain Procurements from the Xinjiang Uyghur Autonomous Region–Representation 252.225-7060 Prohibition on Certain Procurements from the Xinjiang Uyghur Autonomous Region 252.232-7010, Levies on Contract Payments 252.243-7001, Pricing of Contract Modifications 252.246-7007 Contractor Counterfeit Electronic Part Detection and Avoidance System 252.246-7008, Sources for Electronic Parts and 52.212-5, Contract Terms and Conditions Required to Implement Statutes or Executive Orders - Commercial Items including all base terms, conditions, and clauses outlined within the clause, plus the following clauses that have been specifically selected (checked off within the clause) for this procurement: 52.204-10 Reporting Executive Compensation and First Tier Subcontract Awards, 52.204-27 Prohibition on a ByteDance Covered Application, 52.209-2 Prohibition on Contracting with Inverted Domestic Corporations – Representation, 52.209-6 Protecting the Government’s Interest When Subcontracting with Debarred, Suspended, or Proposed for Debarment, 52.219-6, Notice of Total Small Business Set-Aside, 52.219-28 Post Award Small Business Program Representation, 52.222-3 Convict Labor, 52.222-19 Child Labor – Cooperation with Authorities and Remedies, 52.221-21 Prohibition of Segregated Facilities, 52.222-26 Equal Opportunity, 52.222-36 Equal Opportunities for Workers w/ Disabilities, 52.222-50 Combating Trafficking in Persons, 52.223-11 Ozone Depleting Substances, 52.223-18 Encouraging Contractor Policies to Ban Test Messaging While Driving, 52.225-13 Restrictions on Certain Foreign Purchases. 52.232-33 Payment by Electronic Funds Transfer—System for Award Management.

Additional contract terms and conditions applicable to this procurement are:

DFARS 252.203-7000 Requirements Relating to Compensation of Former DoD Officials, DFARS 252.204-7012, Safeguarding of Unclassified Controlled Technical Information Deviation 2016 O0001) DFARS 252.204-7015, Disclosure of Information to Litigation Support Contractors DFARS 252-204-7016, *See Attachment for this clause DFARS 252.204-7017, Prohibition on the Acquisition of Covered Defense Telecommunications Equipment or Services--Representation DFARS 252.204-7018, Prohibition on the Acquisition of Covered Defense Telecommunications Equipment or Services DFARS 252.204-7019 Notice of NIST SP 800-171 DoD Assessment Requirements DFARS 242.204-7020 NIST SP 800-171 DoD Assessment Requirements DFARS 252.209-7999, Representation by Corporations regarding an Unpaid Delinquent Tax Liability DFARS 252.244-7000 Subcontracts for Commercial Items DFARS 252.247-7023 Transportation of Supplies By Sea

DLAD CLAUSES AND PROVISIONS (See Attachment for Full Text)

52.233-9001, Disputes: Agreement to Use Alternative Disputes Resolution

DLA PROCUREMENT NOTES (See Attachment for Full Text)

C01 Superseded Part Numbered Items (SEP 2016) C02 Manufacturing Phase-Out or Discontinuation of Production, Diminishing Sources, and Obsolete Materials or Components (DEC 2016) C03 Contractor Retention of Supply Chain Traceability Documentation (JUN 2020, APRIL 2023) C04 Unused Former Government Surplus Property (SEP 2021) C14 Repackaging or Relabeling to Correct Deficiencies (MAY 2020) C20 Vendor Shipment Module (VSM) (NOV 2020) E05 Product Verification Testing (MAY 2020) H10 Awardee Requires No Access to DLA Controlled Technical Data or Information for Contract Performance (FEB 2020) L01 Electronic Award Transmission (JUN 2020) L04 Offers for Part Numbered Items (SEP 2016) L06 Agency Protests (DEC 2016) L08 Use of Supplier Performance Risk System (SPRS) in Past Performance Evaluations (JUN 2020) L31 Additive Manufacturing (JUN 2018) M05 Evaluation Factor for Unused Former Government Surplus Property (SEP 2016)

LOCAL CLAUSES (See Attachment for Full Text):

YM3 A1: Additional Information YM3 C500: Mercury Control (Supplies) YM3 C506: Qualified Products for Award YM3 C524: Controlled Industrial Material YM3 C528: Specification Changes YM3 D2: Marking of Shipments YM3 D4: Preparation for Delivery (Commercially Packaged Items) YM3 D8: Prohibited Packing Materials YM3 E2: Inspection and Acceptance (Destination) YM3 F500: Consignment Instructions for Deliveries to the Portsmouth Naval Shipyard YM3 H500: Special Provisions for Threaded Products YM3 M8: Single Award for All Items

Quoters are reminded to include a completed copy of 52.212-3 and it’s ALT I if not updated in SAM.

This announcement will close at 10:00 AM EST on November 06, 2023. The Point of Contact for this solicitation is Gary Chandler who can be reached at email gary.1.chandler@DLA.mil. All responsible sources may submit a quote which shall be considered by the agency.

System for Award Management (SAM). Quoters must be registered in the SAM database to be considered for award. Registration is free and can be completed online at http://www.sam.gov/.

If not the actual manufacturer – Manufacturer’s Name Location and Business Size must be provided.

Please submit quotes via email at gary.1.chandler@dla.mil.

Quotes also to: DLA-KME-QUOTATIONS@DLA.MIL

All quotes shall include price(s), FOB point, a point of contact, name and phone number, GSA contract number if applicable, business size, whether or not your company prefers payment by Government Commercial Purchase Card (GCPC) or Wide Area Workflow (WAWF). Please note that the Government’s terms for payment for this requirement are Net 30 Days AFTER acceptance of material. Each response must clearly indicate the capability of the quoter to meet all specifications and requirements.

image1.png