Attachment 1 - Statement of Work.pdf

NIST Statement of Work Vector network analyzer

I. Background

The Photonics and Optomechanics Group at NIST develops photonic integrated circuits, microelectromechanical systems, and optomechanical devices for traceable sensing and measurement applications. Many of these devices operate at microwave frequency and require characterization of their electrical and/or electro-optical frequency responses. As a result, a vector network analyzer is needed to measure the two-port input-output response of micro- and nanofabricated devices, including microwave acoustic resonators and photonic modulators at frequencies up to 67 GHz.

II. Purpose

The vector network analyzer will be used to measure scattering parameters and impedance for microwave acoustic resonators and filter, photonic modulators, and other related devices.

One-port and two-port measurements will be performed with the vector network analyzer.

These measurements will be used to understand loss mechanisms, measure material properties, aid in device optimization, and to better understand their RF dynamics.

III. Minimum Requirements

Contract Line Item 0001:

The Contractor shall provide a Firm Fixed Price quotation for the following:

Vector network analyzer, Quantity 1

The vector network analyzer shall meet or exceed the technical specifications listed below.

All items must be new. Used or remanufactured equipment will not be considered for award. Experimental, prototype, or custom items will not be considered. The use of “gray market” components not authorized for sale in the U.S. by the proposer is not acceptable. All line items shall be shipped in the original manufacturer’s packaging and include all original documentation and software, when applicable.

Technical Specifications:

The vector network analyzer (VNA) must have the following functionalities:

1. Two ports for standard 2-port measurements.

2. A color touch screen display that is 12” diagonal or larger for visualizing measurements and a front panel for operating the instrument.

3. The VNA must be able to measure the S-parameters of RF resonators and filters by sweeping the input frequency to the DUT and measuring the output of the DUT.

4. The VNA must have a configurable test set for each port with access to the source and receiver.

5. The VNA must have an internal hard disk drive for storing measurement data.

6. The VNA must have USB and LAN ports for data communications and instrument control.

7. All VNA capabilities must be included in a single benchtop enclosure. Combinations of multiple packaged components are not acceptable.

8. The VNA must be calibrated prior to delivery using methods compliant with ANSI Z540.

General Specifications

9. Minimum measurement frequency range: 10 MHz to 67 GHz, can be wider

10. Frequency source stability: +/- 2.5 ppm or better over first year

11. Frequency accuracy: +/- 0.8 ppm or better

12. Dynamic range:

a. 121 dB or greater in the frequency range of 1 GHz to 25 GHz

b. 98 dB or greater in the frequency range of 25 GHz to 67 GHz

13. Maximum output power:

a. 10 dBm or greater in the frequency range of 1 GHz to 25 GHz

b. 5 dBm or greater in the frequency range of 25 GHz to 67 GHz

14. Maximum level of harmonics in output signal: -15 dBc or less

15. Output signal level accuracy:

a. +/- 2.5 dB or better in the frequency range of 1 GHz to 25 GHz

b. +/- 4 dB or better in the frequency range of 25 GHz to 67 GHz

16. Output signal level linearity: +/- 3 dB or better above 0.5 GHz

17. Input test port noise floor:

a. -114 dBm or lower in the frequency range of 1 GHz to 25 GHz

b. -101 dBm or lower in the frequency range of 25 GHz to 67 GHz

18. Phase noise for test port sources at 100 kHz offset:

a. -102 dBc/Hz or lower in the frequency range of 1 GHz to 25 GHz

b. -96 dBc/Hz or lower in the frequency range of 25 GHz to 67 GHz

19. Maximum number of measurement points in a sweep: at least 100,000

20. The VNA must operate on 110 – 120 VAC at 60 Hz and the power cable must be included.

IV. Deliverables:

Delivery shall be FOB destination and shall occur within 20 weeks. FOB Destination means:

The contractor shall pack and mark the shipment in conformance with carrier requirements, deliver the shipment in good order and condition to the point of delivery specified in the purchase order, be responsible for any loss of and/or damage to the goods occurring before receipt and acceptance of the shipment by the consignee at the delivery point specified in the purchase order; and pay all charges to the specified point of delivery. The contractor shall deliver all Line Items to:

National Institute of Standards and Technology 100 Bureau Drive Gaithersburg, MD 20899-1640

V. Inspection and Acceptance

In addition to the inspection and acceptance terms articulated in 52.212-4, the Government reserves the right to perform such performance tests and evaluations as defined below to verify specified system performance. Such tests and evaluations, if performed, shall be conducted within the environment that the system is to be operated. The Contractor has the right to be present during the tests and evaluations, if performed, at the Contractor’s expense.

Acceptance test: The vector network analyzer will be used to measure the S21 response of a “through” test structure on a short-open-load-through (SOLT) calibration substrate at frequencies between 1 GHz and 67 GHz. The measured results will be compared to the expected loss of the substrate.

The place of acceptance shall be:

100 Bureau Drive Building 220 Gaithersburg, MD 20899

VI. Installation

Installation will be completed by the purchaser.

VII. Training

No training is required.

VIII. Warranty The contractor shall warrant the software and provide support for a minimum of one year after receipt of the software and shall be in accordance with terms in FAR 52.212-4

IX. Payment Schedule

The Contractor shall be paid, in accordance with Net 30-day payment terms, upon receipt and acceptance of a proper invoice, in accordance with the following schedule:

1. 100% after receipt and acceptance by the TPOC of fully delivered software

2. The Government anticipates inspection will occur immediately upon download.

NOTE: Partial shipments and partial invoices will not be accepted, unless other-wise requested and accepted by the Contracting Officer prior to award offer. Proposed payment schedules shall be submitted with vendor’s response to the RFQ for consideration.