Attachment 1-Drawing.pdf

SPECIAL PACKAGING INSTRUCTION Form Approved OMB No. 0704-0188

Public reporting burden for this collection of information is estimated to average 30 days per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Washington Headquarters Services, Directorate for

Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, Va 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project(0704-0188). Washington, DC 20503. Please do not return your form to either of these addresses.

1. PART OR DRAWING NO. NOMENCLATURE 2. CODE INDENT 3. SPI NO.

7012810-1 MOUNT ASSY, RING, M66 WITH MT, MG, CAL .50 19207 AMP7012810-1

4. NATIONAL STOCK NO. 5.DATE OF

DRAWING/SPI(YYMMDD)

6. REVISION / ERR NO.

1005-00-890-2610 190321 C / L18S3134

7. QUP / UNIT OF ISSUE 8. ICQ 9. UNIT PACK WT. (LB) (0.0) 10. UNIT PACK CU (CU.

FT.)(0.000)

11. UNIT PACK SIZE (INCHES)(00.0)

1/EA 455.0 24.384 53.0 X 53.0 X 15.0

18.

STEPS

19.

REQD

20.

DESCRIPTION

12. MILITARY PRESERVATION 1 AR PRESERVATIVE: SEE NOTE 1.

MIL-STD-2073-1, METHOD 20 2 AR WRAP: MIL-PRF-121, TYPE I. SEE NOTE 1

13. CLEANING 3 AR TAPE: ASTM D6123/D6123M

* 4 1 CONTAINER: ASTM D6251/D6251M, TYPE III,

CLASS 2, STYLE I. SEE NOTE 2.

14. DRYING 5 AR PROT. INSUL: MIL-P-130, TYPE I. SEE NOTE 4.

* 6 5 BLOCKING: ASTM D6199. SEE NOTE 3.

15. PACKING 7 AR CLOSURE: ASTM D6251/D6251M. SEE NOTE 2.

a. LEVEL A

MIL-STD-2073-1

b. LEVEL B

MIL-STD-2073-1

16. MARKING

MIL-STD-129

17. NOTES/DRAWING

SPECIFICATIONS, STANDARDS AND DRAWINGS LISTED HEREIN WHICH ARE IN EFFECT ON THE DATE OF THE SOLICITATION FORM A PART OF THIS PACKAGING INSTRUCTION. THE APPLICABLE GENERAL AND REFERENCED REQUIREMENTS OF SPECIFICATION MIL-STD-2073-1 FORM PART OF THESE INSTRUCTIONS. UNLESS OTHERWISE SPECIFIED, MATERIALS WILL BE MINIMUM SIZE IN ACCORDANCE WITH MIL-STD-2073-1. WEIGHTS AND SIZES ARE ESTIMATED AND MAY VARY SLIGHTLY. INTERMEDIATE PACKAGING AND PACKING WILL BE IN ACCORDANCE WITH

SPECIFICATION MIL-STD-2073-1 OR AS OTHERWISE SPECIFIED HEREIN.

TOLERANCES SHALL BE IN ACCORDANCE WITH MATERIAL SPECIFICATIONS. QUALITY PERFORMANCE AND TESTING REQUIREMENTS SHALL BE IN CONFORMANCE WITH MIL-STD-2073-1, OR AS OTHERWISE SPECIFIED.

* UNLESS OTHERWISE SPECIFIED, CLEANING AND DRYING SHALL BE IN ACCORDANCE WITH PARAGRAPH 5.2.1 OF MIL-

STD-2073-1.

1. PRESERVE ALL UNPAINTED METAL SURFACES WITH PRESERVATIVE AS SPECIFIED ON ITEM DRAWINGS.

WRAP ITEM WITH SPECIFIED MATERIAL AND SECURE WITH TAPE. DO NOT ALLOW TAPE TO CONTACT ITEM.

2. CONTAINER CONSTRUCTION AND CLOSURE SHALL BE IN ACCORDANCE WITH ASTM D6251/D6251M. CONTAINER DIMENSIONS

SHALL BE MAINTAINED AS SHOWN IN BLOCK 11.

3. BLOCKING SHALL BE LOCATED AS SHOWN ON PAGE 2. A 3/8 INCH HOLE SHALL BE DRILLED THRU BLOCK A, THE FLOOR OF

CONTAINER, AND THREE SKIDS AS INDICATED ON PAGE 2.

4. PROTECTIVE INSULATION SHALL BE UTILIZED WHERE ITEM CONTACTS CONTAINER COMPONENTS. LOCATE MOUNT RING

ASSEMBLY AS INDICATED ON PAGE 2.

5. RING MOUNT SHALL BE BOLTED TO CONTAINER WITH FOUR (4) CARRIAGE BOLTS, SIZE 3/8X9 OR LAG BOLTS SIZE 3/8X10 UTILIZING BOLTS AND WASHERS AS APPLICABLE. IF LAG BOLTS ARE USED THEY SHALL BE INSTALLED FROM THE TOP WITHOUT PROTRUDING ON THE BOTTOM OF THE SKIDS. NYLON WASHERS SHALL BE USED BETWEEN THE HEAD OF THE LAG BOLTS OR

METAL WASHERS AND THE RING MOUNT SURFACES.

6. PLACE DEFLECTOR (P/N 11589551) AND WIRE (P/N 10907432-4) IN INDIVIDUAL BARRIER BAGS IN ACCORDANCE WITH MIL-DTL- 117, TYPE III, CLASS B. SECURE BAGGED ITEMS TO RING MOUNT WITH TAPE. DO NOT ALLOW TAPE TO COME INTO CONTACT

WITH ITEM.

7. SKIDS SHALL BE AS DEFINED IN ASTM D6199 AND SHALL BE LOCATED AS INDICATED ON PAGE 2.

8. UNIT CONTAINER SHALL SERVE AS SHIPPING CONTAINER.

WSC: L9 ITEM SIZE: 50.0 x 50.0 x 10.5 ITEM WEIGHT: 333.0 APPROVED: BHOGE K. EUMNATH

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

DD Form 2169, JUN 97 Previous editions are obsolete Page 1 of 2 Pages

SPECIAL PACKAGING INSTRUCTION (Continuation sheet) Form Approved OMB No. 0704-0188

Public reporting burden for this collection of information is estimated to average 30 days per response, including the time for reviewing instructions, searching existing data sources, gathering and maintaining the data needed, and completing and reviewing the collection of information. Send comments regarding this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden, to Washington Headquarters Services, Directorate for

Information Operations and Reports, 1215 Jefferson Davis Highway, Suite 1204, Arlington, Va 22202-4302, and to the Office of Management and Budget, Paperwork Reduction Project(0704-0188). Washington, DC 20503. Please do not return your form to either of these addresses.

1. PART OR DRAWING NO. NOMENCLATURE 2. CODE INDENT 3. SPI NO.

7012810-1 MOUNT ASSY, RING, M66 WITH MT, MG, CAL .50 19207 AMP7012810-1

4. NATIONAL STOCK NO. 5.DATE OF

DRAWING/SPI(YYMMDD)

6. REVISION / ERR NO.

1005-00-890-2610 190321 C / L18S3134

17. NOTES / DRAWINGS CONTINUED

FIGURE 1.

DISTRIBUTION STATEMENT A: APPROVED FOR PUBLIC RELEASE; DISTRIBUTION IS UNLIMITED.

DD Form 2169, JUN 97 Previous editions are obsolete Page 2 of 2 Pages