Attach-4-Power Core Spec Sheet.pdf

sect. 40 1511718 rev. 2015/09/25

In order to consistently bring you the highest quality, full-featured products, we reserve the right to change our specifications and designs at any time. MURPHY products and the Murphy logo are registered and/or common law trademarks of Enovation Controls, LLC. This document, including textual matter and illustrations, is copyright protected by Enovation Controls, LLC, with all rights reserved. (c) 2015 Enovation Controls, LLC. A copy of the warranty may be viewed or printed by going to http://fwmurphy.com/warranty.

The MPC-10 is flexible in many aspects, with the ability to:

• use the same controller on 12VDC or 24VDC systems;

• assign multiple levels of passcode protection to the menu using the free of charge PC Configuration Tool;

• change the input sensor type for the analog inputs;

• use analog inputs as digital ground inputs;

• be mounted in all-weather environments;

• be customer mounted in panel of choice.

PowerCore™ MPC-10 The Murphy PowerCore MPC-10 Controller is a general, all-purpose manual/auto start and manual/ auto throttling engine controller designed with rental applications in mind. The controller is purposed primarily for applications where a wide array of inputs and outputs are not required. This is a powerful and rugged controller that supports J1939 CAN protocols for electronically governed engines as well as analog sensors on mechanical engines for fault and safety shutdowns.

Specifications

Power Input: 8-32 VDC, reverse polarity and load dump protec-tion Cranking Power Holdup: 0 VDC up to 50mS (also good for brownout/blackout instances) Total Current Consumption: Power on in stopped state; 117 mA at 12 VDC. Power on in standby mode; 52 mA at 12 VDC.

Display: 2.7” WQVGA Monochrome HR-TFT 400x240 Keypad: 11 Tactile Feedback Buttons LEDs: (1) Red, Shutdown, (1) Amber, Warning, (1) Green, Auto Mode or Running Loaded State Outputs:

(3) Relays: 10A, SPDT, Form C (30 VDC @ 10A max.), 30A max aggregate @ 85C

(2) Low-side (1A)

(2) High-side (1A)

(1) Dedicated Alternator Excite (provides Charge Fail Fault if unable to excite alternator) Inputs:

(5) Digital, configurable (high/low)

(3) Analog, configurable (4-20mA, 0-5V, resistive)

(1) Frequency, supporting Magnetic pickup (30Hz - 10kHz, 2.0VAC-120VAC) and Engine Alternator (30Hz - 10kHz, 4.5

VRMS - 90 VRMS)

While reprogrammable, the MPC-10 follows a standard operating sequence. This operating sequence is a set of 22 machine states that happen in a predetermined order. Machine states can be set to zero if not needed or adjusted to fit the application. The menu structure is incredibly versatile, with the ability to change many parameters and settings from the face without the need of a PC tool, if desired.

*Approved by CSA for non-hazardous locations (Group Safety Publication IEC 61010-1 Third Edition.

Products covered in this document comply with European Union electromagnetic compatibili-ty directive 2004/108/EC and electrical safety directive 2006/95/EC.

Dimensions

Connectors

Deutsch 12 pin Connector Gray Deutsch 12 pin Connector Black Deutsch 12 pin Connector Green Deutsch 6 pin Connector USB

PIN Function PIN Function PIN Function PIN Function

1 Battery (+) 1 Battery (+) 1 Battery (-) 1 USB1_VBUS

2 RS485 (H) 2 Not Used 2 Battery (+) 2 USB_DP_OUT

3 RS485 (L) 3 Digital Out 2 HS 1A 3 Battery (+) Switched 3 USB_DM_OUT

4 Relay 3 NC 4 Digital Out 1 HS 1A 4 Alt Excite 4 USB_ID_OUT

5 Relay 3 COM 5 Digital Out 2 LS 1A 5 CAN (H) 5 USB_SHLD

6 Relay 3 NO 6 Digital Out 1 LS 1A 6 CAN (L) 6 USB_GND

7 Analog In 3 7 Analog In 1 7 Relay 1 NO

8 Digital In 3 8 Analog In 2 8 Relay 1 COM

9 Digital In 4 9 Digital In 1 9 Relay 1 NC

10 Digital In 5 10 Digital In 2 10 Relay 2 NO

11 Not Used 11 Frequency In 11 Relay 2 COM

12 Battery (-) 12 Battery (-) 12 Relay 2 NC

How to Order

Part Number Model/Description

40700494 MPC-10 Controller

40051142 Panel Gasket, IP66, MPC-10

40700506 PowerCore 3X12 Position Connector Kit

40000598 PowerCore 3X12 Position 3’ Conn Whip Harness (1m approx.)

78000668 USB Programming Harness

Specifications (continued)

Communications:

(1) CAN J1939

(1) RS485, MODBUS RTU

(1) USB 2.0B for Programming

Dimensions:

Width: 6.57 in. (167.09 mm) Height: 5.24 in. (133.29 mm) Depth: 2.55 in. (64.81 mm)

Mass: 1lb. 1oz. (0.5 kg) Operating Temperature: -40°F to 185°F (-40°C to 85°C) Storage Temperature: -40°F to 185°F (-40°F to 85°C)

EMI/EMC: SAE J1113, 2004/108/EC

Shock: ± 50G in axes Vibration: Random, 7.86 Grms (5-2000Hz), 3 axes

Sealing: IP67 front and back, IP66 Panel Seal with Gasket Case: Polycarbonate/ABS Mating Connector: Deutsch Wedge Lock W12S-P012:

Gray DT06-12SA-P012 Black DT06-12SB-P012 Green DT06-12SC-P012 USB 6 pin

Shipping Weight: 2lbs. 7.1 oz. (1.11 kg) Shipping Dimensions:

8 x 8 x 5-11/16 in. (204 x 204 x 127mm) (WxHxD)

Languages: English, Spanish, German, French, Italian