Atch_1_SOW.pdf

140P5421R0026 Attachment 1

Page 1 of 7 Pages

NATIONAL PARK SERVICE

Cumberland Islands National Seashore

STATEMENT OF WORK

Bachlott House

The contractor shall provide all labor, supervision, material, tools, equipment, supplies, transportation and incidentals necessary to wash the entire exterior of the structure, including decking, porch ceiling, handrails, and spindles. Replace 7 single hung, vinyl windows, repair wood, lap siding, less than 5% and brick mold and trim on around windows, approximately 80 linear feet. Scrape and caulk all wood surfaces where paint is flaking and prepare for painting. Coat entire brick chimney, approximately 400 square feet, with a clear sealant to prevent moisture intrusion. Replace approximately 4 linear feet of 6 inch, half round, galvanized gutter. All work shall be done in accordance with generally accepted practices for the trade, all applicable standards and regulations and Secretary of the Interior Standards for Treatment of Historic Properties, and NPS 28: Cultural Management Guideline (Chapter 8), which can be found at https://www.nps.gov/parkhistory/online_books/nps28/28contents.htm.

Contractor Responsibilities:

• Pressure wash entire building. Approximately 4500 square feet of wall surface and approximately 1500 square feet of decking, stairs and ceiling.

https://www.nps.gov/parkhistory/online_books/nps28/28contents.htm

Page 2 of 7 Pages

• Replace 7, single hung Pozzi windows, 6 over 6 panes, (5)- 32”x 66” and (2)- 26”x 62”to match existing.

• Remove and replace approximately 500 linear feet of damaged 1”x 6” lap siding, rough sawn, pine.

• Repair approximately 100 linear feet of soffit, 1”x 6” pine, PT and less than 50 square feet of ½ inch plywood.

• Repair approximately 100 linear feet of 1”x 4” fascia.

• Replace approximately 4 linear feet of galvanized, 6 inch, half round gutter.

• Remove, paint and reinstall all wood lattice around the building. Approx. 150 square feet.

• Pressure wash, prime and paint approximately 125 square feet of wood, picket fence, both sides.

• Use galvanized nails for siding installation.

• Remove, clean and paint 16 sets (32) louvered shutters, 67”x 16”x 1”.

• Metal brackets and locks holding shutters are to be removed, cleaned and reinstalled (79 hinges, 40 locks).

• Scrape all loose paint and caulk all joints and cracks.

• Apply one coat of latex primer on all bare wood surfaces and two (2) coats of latex semi-gloss paint on all wood surfaces. Paint colors to match existing.

• Ensure 8 exterior, 3/0 doors are weather tight and functioning properly.

• Paint all exterior doors, both sides, and trim.

Special Considerations:

• Painting is to be achieved by brush and roller. NO SPRAYING!!!!!

• Approximate square footages for walls includes the doors, windows and trim.

• Replacement material will be like in kind.

• Hinges and doorknobs are to be removed or taped to prevent painting.

• Contractor will comply with all OSHA, Federal, State, and local regulations.

• Construction sites will be cleaned up at the end of each day.

• Disposal of all construction debris is the responsibility of the contractor.

• Work hours are Monday through Friday, 7am-5pm.

• No work on government holidays.

• Work on the weekend must be approved by the COR and must be requested at least 72 hours in advance.

• Ensure water does not enter building around windows and doors while pressure washing.

• Paint colors are to match existing and be approved by the COR.

See following pages for photos

Page 3 of 7 Pages

Page 4 of 7 Pages

Page 5 of 7 Pages

Page 6 of 7 Pages

Page 7 of 7 Pages